Salamander Designs C/ML247/WH/BK, X3/EPS2/237S/SN/MW/BK, C/ML347/WH/BK, X3/EPS2/237S/MM/GW/BK, X3/EPS2/237S/CH/BO/BK Assembly Instructions
Chameleon Options
Media Drawer Assembly
Note: Twin cabinet shown. Follow same process for all congurations.
chameleon
ASSEMBLY INSTRUCTIONS
Congratulations on your purchase!
For any questions please call us at:
800.535.5659 / 860.313.0525 (9am-5pm EST)
Visit our website at: www.salamanderdesigns.com
Media Organizer
Set drawer liner (303-555)
A
TM
on bottom of tray.
Place media organizer
B
(303-310).
Note: Horizontal grooves.
Drawer Liner
2 Install Shelves
For Innitely Adjustable Shelves please skip ahead to “Fine Tuning & Tips.”
TIP:
Speaker Grill Removal
(Applicable Models Only)
Remove by lifting up and out.
A
Chameleon Hardware
You will need a Phillips head screwdriver to assemble your Chameleon Cabinet.
Shelf Pegs
300-835
Socket Screw 1”
(Use with Shelf Peg)
300-455
1 Level Cabinet
Prior to installing components, it is important to level the cabinet with the oor.
Verify that all of the feet are properly adjusted to support the cabinet evenly.
Assemble shelf pegs with
A
socket screws (300-455).
Ax shelf peg assembly
B
to post at desired position
and secure using hex key.
Remove plastic coating from shelves and place onto shelf pegs.
C
Hex Key 3/16’’
400-060
Optional: Innitely Adjustable Shelf Kit (See Fine Tuning)
Socket Screw 3/4”
(Use with Shelf Peg)
300-465
LIMITED WARRANTY
Salamander warrants against manufacturing defects for the lifetime of the product.
Salamander will repair or replace, at our option, any product defective in materials or craftsmanship.
© 2018 Salamander Designs Ltd. Doc No. 501-500 / v 07.18
Hex Key 4mm
400-170
(PHK-2070)
Socket Screw 1.25”
303-520
(Wood Tops Only)
Drop-In Nut
(Use with Shelf Pegs)
300-565
Rubber Pads
303-380
(Glass Tops Only)
Jam Nut
(Applicable Models Only)
Leveler Foot
Loosen jam nut with supplied wrench
and tighten to the locked position.
Wrench included.
Leveler
Wood Block Foot
Lift cabinet and adjust leveler by hand.
TIP:
At this point you may install accessories (IR Repeater Kit, Power
Conditioner, Etc.) and place components.
3 Place & Secure Top
Fine Tuning/Tips
4 Install Door Pulls
(Applicable Models Only)
TIP:
If you have a TV Mount, install it before securing the Top.
Wood Top
Align wood top squarely to the cabinet
A
frame with the holes closest to edge of
top, positioned to the rear of cabinet.
Fasten top to the frame using screws (303-520).
B
Secure pulls with screws
A
using a Phillips screwdriver.
Innitely Adjustable Shelves
Assemble loosely as shown.
A
Socket Screw 3/4’’
(300-465)
Drop-In Nut
(300-565)
Shelf Peg
Glass Top
Place Rubber Pads (303-380) on the frame covering bolts as shown.
A
5 Rear Panels
Insert into post channel and slide to desired height.
B
Level shelf by adjusting shelf peg positions and
tighten screw using hex key.
Note: Drop-in nut must make a 1/4 turn in post.
Aligning Doors
Follow these instructions if you wish to adjust your doors.
Main Adjustment (Side to Side and Up/Down)
Adjustment is made by turning screw (A) in and out.
A
Place the glass top
B
squarely on the cabinet
with the
positioned to the back/left
corner.
Salamander Logo
TIP:
Locate the rear post channels.
A
Lead one end of the rear panel into a
B
post channel.
Compress the rear panel rmly into
C
the opposing post channel.
You may need to wiggle the rear panel to set it into place.
Adjust the tops of the doors to be
parallel to the top of the cabinet.
Door Front
B
Dismount Hinge from Hinge Plate
With one hand holding the door open, pull
back on the hinge quick-release lever (B).
Loading...