Page 1
CHAMELEON
WALL MOUNT
2. MARK WALL LOCATION
A. WOOD CONSTRUCTION - Using a stud finder, mark the locations of
the studs in the area to be covered by the cabinet. It may be necessary to shift the cabinet
slightly left or right to avoid the mounting brackets being obstructed by the vertical
framework of the cabinet.
CAPACITIES (CONTENT)
SINGLE: 100lbs
TWIN: 100lbs
TRIPLE: 200lbs
QUAD: 250lbs
TOOLS REQUIRED
Pencil
3/16” (5 mm) for Wood
3/8” (10 mm) for Masonry
Level
Drill and Bit:
Tap Measure
Stud Finder
COMES WITH
Bracket
(303-850)
Plastic Wall
Plug
BEFORE YOU BEGIN
• This bracket is intended for use with Chameleon 20” Tall Cabinets.
• Total weight capacity of each bracket is: 100 lbs. (45kg). (ex 3 brackets provides
300 lbs. (135kg).
• Carefully inspect your items for shipping damage or missing parts. If any damage is apparent or you are
missing parts contact Salamander Designs Ltd. at 800-535-5659.
• Read ALL assembly instructions before assembly. If you have any questions, please contact your installation
contractor or Salamander Designs.
• Use with products heavier than the maximum weight or other than the cabinet indicated may result
in instability causing possible injury or damage.
• Mounts must be attached as specified in assembly instructions. Improper installation can result in
serious personal injury.
Connector Bolt
(300-540)
1/8” Hex Key (400-070)
3/16” Hex Key (400-060)
6 mm Hex Key
Lag ScrewWasher
Leveling Set Screw
(300-540)
Note: It is not important that the brackets are not located in the same relative location in
each bay. As long as a bracket is located every 16” on center sufficient capacity will be met.
16
16
1. Remove top and feet. Install provided connector bolt in previous foot locations.
B. MASONRY CONSTRUCTION - Mark the wall 2” inward from each
side panel and 2” left or right of each divider panel.
or
2”
Page 2
down 21/
down 27/
4
glass
8
wood
3. MARK HEIGHT LOCATION
Move the cabinet from the mounting location. Determine the desired height of the top
of the cabinet (28” (711mm) is common). From this height subtract 2-1/4” (57mm) for
a glass top cabinet or 2-7/8” (73mm) for a wood top cabinet. This will be the location
of the top bracket top hole. Using a level, mark the remaining intersecting locations at
the same height. Add a second mark 3-3/8” (86mm) below the top bracket hole location
for the second fastener for each bracket.
top bracket hole location
desired cabinet top height
4
21/
or
8
27/
3
8
/
3
ADJUST FOR LEVEL
B. Tighten brackets using a level for proper alignment. Install the leveling screws to
bracket without screw protruding through top of the bracket.
7. HANG CABINET
A. Using two people, lift the cabinet placing the rear upper framing member entirely
into the bracket “hook”.
FINE TUNE LEVELING
A. Adjust side to side to position as desired.
B. Using a level, adjust the leveling screws if necessary. Be sure that all leveling
screws are in contact with the cabinet frame.
4. DRILL WALL HOLES
Predrill mounting holes 21/2” (64mm) deep using a 3/16” (5mm) bit for wood
construction; 3/8” (10mm) bit for masonry construction.
5. INSTALL WALL BRACKETS
A. Install brackets using lag screws (Do not completely tighten). Washers are provided
only to be used between wall and brackets to correct for uneven wall surfaces.
For masonry insert plastic wall plugs prior to mounting brackets with lag screws.
only shim for uneven wall surfaces
masonry only
8. INSTALL A/V COMPONENTS & SECURE TOP
With the top still removed, configure shelving and install your a/v components. When complete, install
cabinet top.For wood tops, use only the front fastening locations.
LIMITED WARRANTY- For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship.
Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure. Defective product must
be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in
original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Doc No. 500-090/v11.10 ©2010 Salamander Designs Ltd.
Loading...