Salamander Designs Barcelona User Manual
chameleon
ASSEMBLY INSTRUCTIONS
Congratulations on your purchase!
For any questions please call us at:
800.535.5659 / 860.313.0525 (9am-5pm EST)
Visit our website at: www.salamanderdesigns.com
1 Level Cabinet
Prior to installing components, it is important to level
the cabinet with the oor. Verify that all of the feet are
properly adjusted to support the cabinet evenly.
TM
Leveler
3 Place & Secure Top
TIP:
If you have a TV Mount, install it before securing the Top.
Wood Top
Align wood top squarely to the cabinet
2 Install Shelves
For Innitely Adjustable Shelves please skip ahead to “Fine Tuning & Tips.”
TIP:
R
L
A
frame with the holes closest to edge of
top, positioned to the rear of cabinet.
Fasten top to the frame using screws (303-520).
B
Chameleon Hardware
You will need a Phillips head screwdriver to assemble your Chameleon Cabinet.
Shelf Pegs “L”
300-840
Shelf Pegs “R”
300-830
Socket Screw 1”
(Use with Shelf Peg)
300-455
Assemble shelf pegs with
A
socket screws (300-455).
L
R
L
R
Glass Top
Place Rubber Pads (303-380) on the frame covering bolts as shown.
A
Afx shelf peg assembly
B
to post at desired position
and secure using hex key.
Hex Key 3/16’’
400-060
Optional: Innitely Adjustable Shelf Kit (See Fine Tuning)
Socket Screw 3/4”
(Use with Shelf Peg)
300-465
LIMITED WARRANTY
For ve full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials
or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and
is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a
shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned
prepaid within the continental U.S.A. only.
© 2011 Salamander Designs Ltd. Doc No. 501-500 / v 8.11
Hex Key 4mm
400-170
(PHK-2070)
Socket Screw 1.25”
303-520
(Wood Tops Only)
Drop-In Nut
(Use with Shelf Pegs)
300-565
Rubber Pads
303-380
(Glass Tops Only)
Remove plastic coating from shelves and place onto shelf pegs.
C
TIP:
At this point you may install accessories (IR Repeater Kit, Power
Conditioner, Etc.) and place components.
Place the glass top
B
squarely on the cabinet
with the
positioned to the back/left
corner.
Salamander Logo
4 Install Door Pulls
Speaker Grill Assembly
(Applicable Models Only)
Media Drawer Assembly
Secure pulls with screws
A
using a Phillips screwdriver.
Speaker Grille Hardware Bag - PHK-2085
Bracket
303-370
Attach the two brackets (303-370) using the wafer-
A
head screws (300-115) to backside of speaker grill.
Note the “UP” arrow.
Socket Screw
300-465
Waferhead Screw
300-115
Rubber Cover
303-375
Grill Pad
303-545
Set drawer liner (303-555)
A
on bottom of tray.
Place media organizer
B
(303-310).
Note: Horizontal grooves.
Fine Tuning/Tips
Innitely Adjustable Shelves
Media Organizer
Drawer Liner
5 Rear Panels
Place grill pads (303-545) ush to corner edges.
B
Afx socket screw (300-465)
C
into second hole from top
on inside of posts. Place
rubber covers (303-375)
on screw heads.
Hang speaker grill on brackets.
D
NOTE: Remove by lifting up and out.
Assemble loosely as shown.
A
Drop-In Nut
Socket Screw 3/4’’
(300-465)
Insert into post channel and slide to desired height.
B
Level shelf by adjusting shelf peg positions and
tighten screw using hex key.
1
2
Note: Drop-in nut must make a 1/4 turn in post.
Shelf Peg
(300-565)
Aligning Doors
Follow these instructions if you wish to adjust your doors.
Main Adjustment (Side to Side and Up/Down)
Adjustment is made by turning screw (A) in and out.
A
TIP:
Locate the rear post channels.
A
Lead one end of the rear panel into a
B
post channel.
Compress the rear panel rmly into
C
the opposing post channel.
You may need to wiggle the rear panel to set it into place.
Adjust the tops of the doors to be
parallel to the top of the cabinet.
Door Front
B
Dismount Hinge from Hinge Plate
With one hand holding the door open, pull
back on the hinge quick-release lever (B).
Loading...