Salamander Designs 345C-B User Manual

SYNERGY 345

!

Quad Assembly

Includes:

(1) Quad 30 Baseunit

(4) Side Panels

(4) Rear Panels

(2) S20 Doors

(2) S30 Doors

(6) Adjustable Shelves

(1) Double Width Shelf

BEFORE YOU BEGIN:

!

• Unpack all parts before beginning and refer to the drawing below.

• Shelf pegs and door hinges must slide into the channels of the post in the correct order.
They cannot be removed individually without disassembling the whole unit.

Limited Warranty

For five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or
destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing
material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.

Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com ©2012 Salamander Designs Ltd. ® Synergy System, Patented.

Doc No. 501-092/v10.12 345 - 1 of 4

1

!

Connect Posts to Bottom Shelf

WARNING: Tighten by screwing the leveler foot NOT the post.

!

A. Connect Post

Screw foot with metal washer through bottom
shelf and onto the end of each extruded post.
Place the 17.75” Post front and center of unit.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.

B. Square Post

Square the post to the bottom shelf.

90

2

Add Shelf Pegs & Door Hinges

A. Group Shelf Pegs

There are two varieties of shelf pegs (A and B).
They are designed to cradle the shelf in place.

O

Refer to drawing.

B

A

A

B

A B

C. Post Cover

Press post cover onto 8.5” center
post to protect the center shelf.

Washer

Hex Nut

Leveler Foot

B. Door Hinges & Shelf Pegs

1. Slide the bottom hinge plate through

the front post channels. (Doors can be
either left or right side opening.)

2. Insert shelf peg into each post in

quantities indicated.

3. Slide top hinge plate through front

post channels.

C. Heavy Duty Bracket

The heavy duty brackets will be used
to supoort the double-width shelf.

Doc No. 501-092/v10.12 345 -2 of 4

3

Attach Doors

A. Attach Hinges to Door Frames

Insert the hinges into the corresponding holes on
the doors. Turn the screws 1/4 turn to the right to
lock hinges in place.

or the hinge will break.

NOTE: Do not over tighten

Note: The hinge can be separated by pulling the
black tab and pulling apart the hinge from the
hinge base. Separated hinges snap back together.

PULL

B. Adjust Clearance

Doors should be 1/8” above the bottom shelf before
fully tightening hinges to post. Use the wrench thickness
as a guide for the bottom gap. Secure hinges in place
with hex key.

C. Rubber Stops

Attach the rubber stops to the inside of the door
frame where it hits the shelf pegs.

SHELF

PEG

D. Door Pull

Screw the Door Pull into place.

Doc No. 501-092/v10.12 345 -3 of 4

4

DE F INING ORIG INAL

™

DE F INING ORIG INAL

™

DEFINING ORIGINAL

™

Logomark

Logotype

TaglineRule

Attach Rear Panels

5

Final Assembly

A.

Insert Hardware

Combine the 1” threaded studs with the flat nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the three center posts.
Allow studs to remain loose at bottom of post.

2X

4X

REAR

4X

B. Position & Secure Studs

Align the Spacer Tool at the top of each post, then
position top studs through the small “Rear Panel”
hole. Repeat this step with the bottom studs
aligning the Tool along the bottom of post to
set spacing for cable passage. Use the hex key

to secure the top and bottom studs to the posts.

4X

2X

A. Placing & Adjusting Shelves

Place shelves from the bottom up. Angle the
shelf in between the front post and set on top
of shelf pegs. Use the Spacer Tool to adjust
spacing between shelves. Position the peg
through the Spacer and tighten.

B. Fine Tuning

Use the bubble level to precisely adjust
the shelves. Be sure to level both sides
as well as front to back. Use the hex
key to tighten each peg.

C. Insert Side Panels

Carefully slide side panels down center
channel of outside posts. Be sure the
posts are square to the bottom shelf to
prevent any damage to side panels.

SOFT

CLOSE

INSTALLATION

A

C. Place Rear Panels

Secure each panel in place with thumb nuts.

D. Secure Top

Secure top with the 8 connector bolts to
complete installation.

B

SLOW CLOSE

FAST CLOSE

Doc No. 501-092/v10.12 345 -4 of 4