Salamander SYNERGY 229 Assembly

TM

SYNERGY 229

Twin Assembly

Includes:

(1) Twin 20 Unit

(2) S20 Side Panels

(2) S10 Doors

(1) Double-Width Shelf

Salamander Designs Ltd. • 800-535-5659 • www.SalamanderDesigns.com ©2008 Salamander Designs Ltd. Synergy System, Patented.

Limited Warranty

Five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in
a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.

Doc No. 500-615/v8.12 229 -1/4

BEFORE YOU BEGIN:

• Unpackallpartsandreadinstructionscarefullybeforebeginning.

•Shelfpegsanddoor hingesmustslideintothechannelsofthepost inthecorrectorder.

They cannot be removed individually without disassembling the whole unit.

1

90

O

B. Connect Post

Screw foot with metal washer through bottom
shelf and into the end of each extruded post.
Hand tighten fully and use wrench to tighten
nut onto underside of shelf.

A. Square Post

Square the post to the bottom shelf.

Connect Posts to Bottom Shelf

!

!

Short Post

WARNING: Tighten by screwing the leveler foot NOT the post.

Leveler Foot

Hex Nut

Washer

1 234 5 6

7

89

S20 /

SVDO

REAR PANEL

4

1/2

"

6"

8"

www.salamanderdesigns.com

EXTENDED
REAR PANEL

S30

/ S40

REAR PANEL

Doc No. 500-615/v8.12 229 - 2/4

C

2

Installing Hardware

D. Heavy Duty Bracket

Install heavy duty brackets down outer
posts to support the double-width shelf.
Place rubber shelf tabs through bracket.

A. Bottom Door Hinges

Slide the bottom door hinge
plates through the front post
channels.

B. Door Stops

Insert one left and one right door stop
down center post.

C. Top Door Hinges

Slide the top door hinge plates
through the front post channels,
aligning with bottom door hinges.

D

A

A B

A. Insert Hardware

Combine the 1” threaded studs with flat nuts.
Slide 2 sets of hardware down the two outside
posts and 4 sets down the center post. Allow
studs to remain loose at bottom of post.

B. Position & Secure Studs

Align the Spacer Tool at the top of each post,
then position top studs through the small “Rear
Panel” hole. Repeat this step with the bottom
studs aligning the Tool along the bottom of post
to set spacing for cable passage. Use the hex key
to secure the top and bottom studs to the posts.

C. Place Rear Panels

Secure each panel in place with thumb nuts.

Attach Rear Panels

3

4X

2X

2X

C

A

D

B

1 2 3 4 5 6 7 8 9

S20 / SV

DO

REAR PANEL

4

1/2

"

6"

8

"

www.salamanderdesigns.com

EXTENDE

D

REAR PA

NEL

S30

/ S40
REAR PAN

EL

SP

ACER

TOOL

1 2 3 4 5 6 7 8 9

S20

/ SVDO

REAR PA

NEL

4

1/2

"

6"

8"

www.salamanderdesigns.com

EXTEND

ED
RE

AR PANEL

S30 / S4

0
REAR PA

NEL

SPACER

TOOL

1 2

3 4

5 6 7

8 9

S
2
0

/
S
V
D

O

R
E
A
R
P

A
N
E
L

4

1

/
2

"

6"

8"

www.salamanderdesigns.com

E
X
TE

ND
E
D

R
E
A
R

P
A
NE
L

S3
0
/

S
4
0

R
E
A
R

P
A
N
E
L

SPACER

TOOL

To ease installation of rear
panels, gently place the unit
face down on the floor to
improve aligning of panels.

TIP

B. Double-Width Shelf

Place double-width shelf on brackets.

A. Rubber Pads

Place rubber pad on top of center post.

A

B

A. Insert Side Panels

Carefully slide side panels down
outside posts. Be sure the posts are
square to the bottom shelf to prevent
any damage to side panels.

Doc No. 500-615 /v8.12 229 -3/4

4

Placing Shelves

B . Secure Top

Secure top with the 5 connector bolts.

Place the plastic plugs in the front center hole.

5

Sides and Top Assembly

A. Attach Hinges to Door Frames

Insert the hinges into the corresponding holes
on the doors. Turn the screws 1/4 turn to the
right to lock hinges in place. NOTE: Do not over
tighten or the hinge will break.

D. Door Pull

Screw the Door Pull into place.

Doors should be 1/8” above the bottom shelf before fully
tightening hinges to post. Use the wrench thickness as a guide
for the bottom gap. Secure hinges in place with hex key.

Attach the rubber stops to the
inside of the door frame where
it hits the shelf pegs.

Attach Doors

Note: The hinge can be separated by pulling the

black tab and pulling apart the hinge from the hinge
base. Separated hinges snap back together.

LIFT UP

SHELF
PEG

6

Doc No. 500-615/v8.12 229 -4/4

B. Adjust Clearance

C. Rubber Stops

A

B

SOFT

CLOSE

INSTALLATION

SLOW CLOSE

FAST CLOSE