Page 1
SYNERGY TWIN UNIT - SN20 / SN30 / SN40
CONNECTOR BOLTS
TOP SHELF
ALUMINUM POSTS
SHELF PEG
LEVELER FOOT
HEX NUT
WASHER
HEAVY SHELF BRACKET
LOW HEAD SCREW
FLAT NUT
RUBBER TAB
BOTTOM SHELF
WARNING: If you are installing accessories such as doors or drawers to the base unit, read all
instructions for the accessory and install in conjunction with these instructions.
!
* Diagram: Synergy 40 Twin Unit
Doc No. 500-350 1 of 4
Page 2
Salamander Designs Ltd. 800-535-5659 • www.SalamanderDesigns.com
©2002 Salamander Designs Ltd.
(300-470)
Washer
(300-540)
Connector Bolt
(P-300-320) - Leveler Foot
6x
6x
6x
(P-400-040) - Level
(400-060) - 3/16” Hex Key
1x
1x
Limited Warranty
For five full years Salamander Designs Ltd will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any
damage to or destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the
original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via
UPS within the continental U.S.A. only.
Rear Panel Bag - PHK-240
2x
8x
8x
8x
(400-070) - 1/8” Hex Key
(300-560) - Flat Nut
(300-530) - ThumbNut
(300-510) - Stud
Heavy Shelf Bracket
PHK-150 (Only SN40)
Parts
6 - Aluminum Posts Adjustable Shelf (SN20 -2) • (SN30 - 4) • (SN40 - 8)
1 - Top Shelf Heavy Duty Shelf Bracket (SN40 - 4)
1 - Bottom Shelf 1 - Spacer Tool
2 - Rear Panels
(PHK-370)
Shelf Peg “B”- Right
SN20 -4x
SN30 - 8x
SN40 - 12x
(PHK-380)
Shelf Peg “A” - Left
SN20 - 4x
SN30 - 8x
SN40 - 12x
8x
8x
(300-490)
Low Head Screw
(300-610)
Rubber Tab
1x
(400-035) - Wrench
8x
(300-560) - Flat Nut
Doc No. 500-350 2 of 4
Page 3
1
B
B
A
A
Leveler Foot
Hex Nut
Washer
90
O
B. Connect Post
Screw foot with metal washer
through bottom shelf and onto
the end of an extruded post.
Hand tighten fully then use
wrench on hex nut to tighten
nut onto underside of shelf.
A. Square Post
Square the post to the bottom shelf.
B.
Gently tighten pegs and brackets
with the hex key to desired position.
A.
Insert all shelf pegs and heavy
shelf brackets (SN40 only)
down each post.
Connect Posts to Bottom Shelf
WARNING: Tighten by screwing the leveler foot NOT the post.
2
Add Shelf Pegs
WARNING: If you are installing an optional door or drawer refer to
specific instructions before proceeding.
!
!
Doc No. 500-350 3 of 4
Page 4
Side Panels
Before enclosing the unit
with the top shelf install
side panels (if applicable).
See Side Panel Instructions
C. Fine Tuning
Use the bubble level to precisely adjust
the shelves. Be sure to level both side
to side as well as front to back. Use
the hex key to tighten each peg.
A.
Adjusting Shelves
Insert peg down the post channel
and position the peg through the
Spacer and tighten. You may also
consider using books or CD's for
shelf spacing.
A. Insert Hardware
Combine the 1” threaded studs
with the flat nuts. Slide hardware
into rear channel
B. Secure Rear Panel
Secure thumb nuts to finish panel
installation.
C. Install Top
Insert the four connector bolts and
tighten shelf down.
1 2 3 4 5 6 7 8 9
S
2
0
/
S
V
D
O
R
E
A
R
P
A
N
E
L
4
1/2
"
6"
8"
www.salamanderdesigns.com
E
X
T
E
N
D
E
D
R
E
A
R
P
A
N
E
L
S
3
0
/
S
4
0
R
E
A
R
P
A
N
E
L
SPACER
TOOL
1 2 3 4 5 6 7 8 9
S
2
0
/
S
V
D
O
R
E
A
R
P
A
N
E
L
4
1/2
"
6"
8"
www.salamanderdesigns.com
E
X
T
E
N
D
E
D
R
E
A
R
P
A
N
E
L
S
3
0
/
S
4
0
R
E
A
R
P
A
N
E
L
SPACER
TOOL
2X
2X
2X
REAR
8"
SPACER
TO
O
L
B. Placing Shelf
Place shelves from the bottom up.
Angle the shelf in between the front
post and set on top of shelf pegs
and heavy duty brackets.
1 2 3 4 5
S
2
0
/ S
V
D
O
R
EA
R
P
A
N
E
L
www.salamanderdesigns.com
EX
T
E
N
D
E
D
R
EA
R
P
A
N
EL
S
3
0
/ S
4
0
R
E
A
R
P
A
N
E
L
3
Adjust Shelf Pegs / Add Shelves
4
Attach Rear Panel
STOP
Doc No. 500-350 4 of 4
Loading...