Page 1
D1/367A ASSEMBLY INSTRUCTIONS
6 BAY Low Profile WALL MOUNT CABINET
TIP HAZARD WARNING!
Cabinet must be affixed to wall. For use to prevent tipping in compliance with
capacity of cabinet specified. Use with heavier equipment may result in instability
or detachment causing tip over resulting in death or serious injury.
Salamander 6 Bay Low Prole Wall Mount Cabinet 1 of 11 503-250 [5.17]
Page 2
hardware
A
B
C
E
F
N
O
H
D
G
I
ID PART # DESCRIPTION
A 300-485 1/4-20 x 1/2” Button Head Socket Screw
J
K
L
B 300-465 1/4-20 x 3/4” Head Socket Screw
C 301-730 5/16 x 2.5” Lag Bolt
D 301-745 Hollow Wall Anchors
E 300-565 Drop In Nut
F 300-470 5/16” Flat Washer
G 400-035 Leveler Wrench
H 303-855 Universal Wall Bracket
I 300-468 1/4” Flat Washer
J 300-518 1/4-20 x 3/8” Button Head Socket Screw
K 302-310 10-32 x 5/8” Button Head Socket Screw
L 300-835 Universal Shelf Peg
M 301-055 3/8 x 2” Alligator Wall Anchors
M
Salamander 6 Bay Low Prole Wall Mount Cabinet 2 of 11 503-250 [5.17]
N 303-453 1/4-20” x 4” Head Socket Screw
O 300-532 1/4-20 Lock Nut
Page 3
TOOLS INCLUDED
Tools needed
PART # DESCRIPTION
P-400-030 Driver Bit 1/4” Hex Key
400-030 1/4” Hex Key
400-070 1/8” Hex Key
400-080 5/32” Hex Key
400-058 3/16” Hex Key- Short Arm
Drill Driver
#2 Phillips Head Screw Driver
1/2 Drill Bit for Standard Installation
3/16” Drill Bit for Wood Stud Installation
3/8” Drill Bit for Masonry Installation
Pencil
Tape Measure
Level
warnings
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS FURNISHING
WARNING! Failure to comply with these instructions may result in accident involving serious personal
injury. Failing to follow these instructions can result in the product being damaged or being destroyed or
voiding of the warranty.
CAUTION!
• Close supervision is necessary when this furnishing is used by or near children, invalids,
or disabled persons
• Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
• Do not use outdoors
• For Commercial Use Only
***** SAVE THESE INSTRUCTIONS *****
Accessories and Spare Parts
Please contact Salamander Designs 860.761.9500 or www.salamanderdesigns.com/commercial
Salamander 6 Bay Low Prole Wall Mount Cabinet 3 of 11 503-250 [5.17]
Page 4
WARNING! This step requires two people.
1. UNIFY cabinetS
Align the top and bottom thru holes located on the front and back vertical cabinet
extrusions.
Bolt together as shown with screw (N), washers (I) and lock nut (O).
I
I
N
O
Salamander 6 Bay Low Prole Wall Mount Cabinet 4 of 11 503-250 [5.17]
Page 5
2. install MOUNTING BRACKETS
TIP HAZARD WARNING! Cabinet MUST be affixed to wall.
A
Loosely mount Bracket (H)
using Screw (A), Washer (I)
and Drop-In Nut (E) to rear
Horizontal Extrusion as shown.
E
H
I
A
Salamander 6 Bay Low Prole Wall Mount Cabinet 5 of 11 503-250 [5.17]
Page 6
WARNING! This step requires two people.
3. Level cabinet & MARK WALL
Prior to fastening to wall, it is important to level the cabinet
with the floor by verifying that feet are properly adjusted.
Check and level Length and Depth of cabinet.
Jam Nut
A B
Loosen jam nut with supplied wrench
and tighten to the locked position.
NOTE:
Adjustments has been provided in the bracket
to mount the cabinet 0-1” of the wall to account
for baseboard trim or other obstacles.
Salamander 6 Bay Low Prole Wall Mount Cabinet 6 of 11 503-250 [5.17]
Place cabinet in desired location and
mark bracket holes. Once holes have
been marked move cabinet.
Page 7
4. install WALL FASTENERS (most applications)
Install wall fasteners to marked location on wall & fasten cabinet.
NOTE: Alternate fasteners (C & F) provided for wood studs.
Drill 1/2” diameter hole. Hold metal
A B
channel flat alongside plastic straps
and slide channel through hole.
Snap straps at wall by pushing side
C D
to side,snapping of straps level with
flange of cap.
Hold ends of straps between thumb
and forefinger and pull toward you
until channel rests flush behind wall.
Slide plastic cap along straps with either
hand with flange of cap is flush with wall.
Move cabinet to wall and attach
bracket. Insert bolt through Bracket
and tighten until snug against wall.
Salamander 6 Bay Low Prole Wall Mount Cabinet 7 of 11 503-250 [5.17]
Page 8
4B. install WALL FASTENERS (ALTERNATE)
WOOD: Locate two framing studs using a stud finder device.
A
MASONRY: Place brackets in desired location.
Use a 3/16” [5mm] drill bit and drill holes 2.5” [64mm] deep.
B
F
M C
Insert wall anchors (M) into hole.
C D
Place cabinet in place and fasten
with washers (F) and Lag Bolts (C).
Salamander 6 Bay Low Prole Wall Mount Cabinet 8 of 11 503-250 [5.17]
Page 9
5. install Brush seal
Use with baseboard molding, trim work or gaps in uneven wall surfaces.
Brush Seal Holders should stay flush to surface so that ONLY brush is showing.
Cabinet Side
A
Peel off tape and install from inside
of cabinet by aligning and afxing
the brush seal to rear inside panel.
Salamander 6 Bay Low Prole Wall Mount Cabinet 9 of 11 503-250 [5.17]
Page 10
6. install Shelves
NOTE: Shelf pegs can be re-positioned if desired.
A. Place shelves on pegs.
B. Install shelf stops in front or back of shelf as desired.
C. Shelf placement can be adjusted if necessary to either pre-drilled.
locations or any location using Drop-In Nuts (E) supplied.
D. Install accessories (IR Repeater Kit, Power Conditioner, etc) and place components.
C
A
B
Drop-In Nut Option
Should you desire shelf placement in location other than
predrilled locations, use the drop-in nut option.
This option allows shelf to be placed at any height.
B
L
Assemble loosely as shown.
E
Insert into post channel
and slide to desired height.
Level shelf by adjusting
shelf peg positions and
tighten screw using hex key.
Note: Drop-in nut must
make a 1/4 turn in post.
Salamander 6 Bay Low Prole Wall Mount Cabinet 10 of 11 503-250 [5.17]
Page 11
ADJUSTMENT TIPS
3U Vertical Rack
Remove
Loosen screws on both sides.
Then tilt rack until the hook is
free and lift up until the rack is
free from bottom screw.
NOTE: It is important that cabinet is level before adjusting doors, see step 3.
Main Adjustment (Side to Side and Up/Down)
A
Adjustment is made by turning screw (A) in and out.
B
Re-Install
Slide the slotted ends of the
A B
rack over the bottom screw and
hook the top screw as shown.
DOORS
Adjust the tops of the doors to be
parallel to the top of the cabinet.
A
Door Front
A
A
Tighten with provided
Hex Key.
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS
Salamander is proud to stand behind our products with industry-leading warranties. Should you ever encounter any problem with your
Salamander product, let us know. We are here to make it right. 1.860.761.9500
Full warranty including limitations and warranty claim information may be found at www.salamanderdesigns.com/commercial/warranty
Salamander 6 Bay Low Prole Wall Mount Cabinet 11 of 11 503-250 [5.17]
Dismount Hinge from Hinge Plate
With one hand holding the door open, pull
back on the hinge quick-release lever (B).
Made in USA
Loading...