Sala 5903922 User Manual

OSHA 1926.502
OSHA 1910.140

confIned space entry/rescUe

ADvAnceD ADjustAble offset DAvit system

The Ultimate in Fall Protection

8518006
8518385
8518386
8518387

User InstrUctIon ManUal

5903922 Rev. D

1

8518040

2

8518008

4

2

3

8515656

5

© 3M 2020

2

D

D

D

B

C

A

FC

3 4

A

B

C

FC

B

C

3

5 6

A B C

7 8

A. B. C. D.

E. F. G.

8518385,
8518386,
8518387

8518385,
8518386,
8518387

X

A

A

9

D

F

E

G

K

8518509,
8518002,
8518003,
8518004

0

K

I

X

B

J

8518008

D

H

4

M

10

M

K

N

L

H

L

L

G

G

11

V

R

R

Q

O

T

S

L

P

O

5

12

A4

A3

A1

A2

*Max.

15in.

A

X

37.0 in.

(94.0 cm)

29.0 in.

(73.7 cm)

39.0 in.

(99.0 cm)

30.0 in.

(76.2 cm)

41.0 in.

(104.1 cm)

32.0 in.

(81.3 cm)

43.5 in.

(110.5 cm)

33.0 in.

(83.8 cm)

X

PP

A2/A3

4

3

2

1

A4

MAX 31.0 in.

MIN 24.0 in.

MAX 33.5 in.

MIN 25.0 in.

PP1 PP2 PP3 PP4

(78.7 cm)

(61.0 cm)

(85.0 cm)

(63.5 cm)

33.5 in.

(85.0 cm)

26.0 in.

(66.0 cm)

36.0 in.

(91.4 cm)

27.0 in.

(68.6 cm)

PP1 PP2 PP3 PP4

A1

A2

A3

A4

*5,000 lbf (22 kN) @ ≤ 15in. (38 cm)

5,000 lbf*

(22.2 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

5,000 lbf*

(22.2 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

5,000 lbf*

(22.2 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

5,000 lbf*

(22.2 kN)

1,800 lbf

(8 kN)

1,800 lbf

(8 kN)

BPP

13

1

2

3

4

W

BPP PP

1 1

2 2 & 1

3 3, 2 & 1

4 4, 3, 2 & 1

BPP

4

3

2

1

W

6

14

5

6

8

1

7

1

4

2

3

2

3

4

WARNING/AVERTISSEMENT

This component is rated for a working load of

450 lb. (205 kg). Retractable devices or shock absorbers

must have an AVERAGE ARRESTING FORCE OF 900 lb. (4kN)

OR LESS, to provide a safety factor of 2:1. System rating is

that of the lowest rated system component.

Cette composant est conçu pour une charge de travail de

450 lb (205 kg). Des dispositifs rétractables ou amortisseurs

doit avoir une moyenne force d’arret de 900 lb (4 kN) ou

moins, pour fournir un facteur de sécurité de 2:1.

Classement du Système est celui de la composante plus

bas nominale système

8513219 Rev. C

15

5

6

7

8

22 kN

(5000 lb)

7

14

1

2

1

3

17

3

16

2

WARNING/AVERTISSEMENT

This component is rated for a working load of

450 lb. (205 kg). Retractable devices or shock absorbers

must have an AVERAGE ARRESTING FORCE OF 900 lb. (4kN)

OR LESS, to provide a safety factor of 2:1. System rating is

that of the lowest rated system component.

Cette composant est conçu pour une charge de travail de

450 lb (205 kg). Des dispositifs rétractables ou amortisseurs

doit avoir une moyenne force d’arret de 900 lb (4 kN) ou

moins, pour fournir un facteur de sécurité de 2:1.

Classement du Système est celui de la composante plus

2

1

bas nominale système

8513219 Rev. C

3

1

18

19

1

2

3

8

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Conned Space

Entry/Rescue Device. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Conned Space Entry/Rescue Device is intended for use as part of a complete personal fall protection or rescue system.

Use in any other application including, but not limited to, non-approved material handling applications, recreational or sports related activities, or

other activities not described in the User Instructions or Installation Instructions is not approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

! WARNING

This Conned Space Entry/Rescue Device is part of a personal fall protection or rescue system. It is expected that all users be fully trained in the

safe installation and operation of the complete system. Misuse of this device could result in serious injury or death. For proper selection,
operation, installation, maintenance, and service, refer to all Product Instructions and all manufacturer recommendations, see your supervisor, or
contact 3M Technical Service.

• To reduce the risks associated with working with a Conned Space Entry/Rescue Device which, if not avoided, could result in

serious injury or death:

- Inspect the device before each use, at least annually, and after any fall event. Inspect in accordance with the User Instructions.

- If inspection reveals an unsafe or defective condition, remove the device from service and repair or replace according to the User

Instructions.

- Any device that has been subject to fall arrest or impact force must be immediately removed from service. Refer to the User Instructions
or contact 3M Fall Protection.

- The device must only be installed in the manner detailed in the Installation Instructions or User Instructions. Installations and use outside
the scope of the instruction must be approved in writing by 3M Fall Protection.

- The substrate or structure to which the device is attached must be able to sustain the static loads specied for the device in the
orientations permitted in the User Instructions or Installation Instructions.

- Do not exceed the number of allowable users.

- Never work below a suspended load or worker.

- Use caution when installing, using, and moving the device as moving parts may create potential pinch points. Refer to the User

Instructions.

- Ensure proper lockout/tagout procedures have been followed as applicable.

- Never attach to a system until it is positioned, fully assembled, adjusted, and installed. Do not adjust the system while a user is attached.

- Only connect fall protection subsystems to the designated anchorage connection point on the device.

- Prior to drilling or fastening, ensure no electric lines, gas lines, or other critical embedded systems will be contacted by the drill or the

device.

- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet
the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements.
Always consult a Competent or Qualied Person before using these systems.

EN

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with

your doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or

suitability of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections.
Consult 3M prior to using this equipment in combination with components or subsystems other than those described in the User
Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures,
chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or the fall protection
equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an

unintended fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.

FORM NO: 5908277 REV: A

9

Prior to installation and use of this equipment, record the product identication information from the ID label in the

;

Inspection and Maintenance Log (Table 3) at the back of this manual.

Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M

;

Technical Services for updated instruction manuals.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ DBI-SALA® Advanced Adjustable Offset Davit System. The System is designed to be attached to a
person for the purpose of raising or lowing them to a workspace. This instruction covers Advanced Variable Offset Masts with an
offset range of 24 inches (61 cm) to 44 inches (112 cm). All one-piece davits (8518385, 8518386, and 8518387) must not be
used with mast extensions or the Portable Base (see Figure 8). The Advanced Variable Offset Mast (Figure 7) may be equipped
with front mounted and/or back mounted winches (A) and Self-Retracting Devices (SRDs). When using the 8518006 davit with

a xed base, a maximum of two mast extensions/lower masts may be combined, but must not exceed 78 inches (198.1 cm) in

height.

As illustrated in Figure 10, the Offset Mast is equipped with two pulleys (A3, A4) and a U-bracket (A2), which are rated as OSHA

approved fall arrest anchor points when used with a device with a 900 lbf (4 kN) average arresting force. The mast mounted
U-bracket (A1) is rated as an 5,000 lbf (22 kN) anchor point when used within 15 inches (38 cm) of the base.

Figure 2 illustrates the components of the Davit System.

Table 1 – Specications

Specications:

Capacity: One person with a combined weight (clothing, tools, etc.) of no more than 310 lb. (141 kg).
Material Handling: 450 lb. (205 kg) maximum load
System Weights: 8518006 - 31 lb. (14 kg)

8518385 - 40 lb. (18 kg)
8518386 - 44 lb. (20 kg)
8518387 - 50 lb. (23 kg)
8518040 - 138 lb. (62 kg)
8518008 - 116 lb. (53 kg)

Component Specications:

Figure 2

Reference Component Materials

A Variable Offset Mast Aluminum

B Lower Mast Aluminum

C Hoist Base Aluminum

D Pulleys Nylon

Hardware Steel/Stainless Steel

Anchorage Requirements:

Moment Load for the Structure 80,000 in-lb (9.0 kN-m)
Vertical Load for the Structure 5,000 lbf (22 kN)

Structure resistance validation and installation execution must be performed by a Qualied Person1.

;

1  Qualied Person: An individual with a recognized degree or professional certicate, and extensive experience in Fall Protection. This individual must be capable

of design, analysis, evaluation, and specication in Fall Protection.

10