T
T
T
R
R
R
A
A
A
C
C
C
E
E
E
R
R
R
&
T
R
A
C
E
R
I
&
T
R
A
C
&
T
R
A
C
E
E
R
R
I
I
I
I
I
1
1
1
2
2
2
0
0
W
i
n
t
e
l
l
i
g
e
n
t
d
i
s
c
h
a
r
g
e
f
0
0
W
i
n
t
e
l
l
i
g
e
n
t
d
i
s
c
h
a
r
0
0
W
i
n
t
e
l
l
i
g
e
n
t
d
i
s
c
h
USER’ S MANUAL release 1.0
This manual must be considered an integral part of the projector.
a
r
g
g
e
e
o
f
o
f
o
l
l
o
w
s
p
o
l
l
o
w
o
w
s
s
l
l
p
p
o
o
t
t
t
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
tech@lamposrl.it
INDEX
GENERAL DESCRIPTION OF PROJECTOR --------------------------------------------------- page 2
START-UP PROCEDURES -------------------------------------------------------------------------- page 5
CONTROL UNIT ---------------------------------------------------------------------------------------- page 6
WHAT’S INSIDE ----------------------------------------------------------------------------------------- page 7
DMX CHANNEL ASSIGNMENT -------------------------------------------------------------------- page 8
CONTROL SYSTEMS --------------------------------------------------------------------------------- page 10
OPTICAL SYSTEM ------------------------------------------------------------------------------------ page 13
MAINTENAINCE ---------------------------------------------------------------------------------------- page 14
TROUBLESHOOTING -------------------------------------------------------------------------------- page 16
SPARE PARTS ----------------------------------------------------------------------------------------- page 17
WARRANTY --------------------------------------------------------------------------------------------- page 17
1
GENERAL DESCRIPTION OF PROJECTOR
TRACER is an intelligent followspot ideal for distance between 10 and 50mt, it has a built in ballast, 4 different
beam angle (10° – 12° – 14° – 16°) and it is perfectly balanced. Tracer has a colour wheel, filter correction, frost
filter, focusing, dimmer and strobe, this effects is controller by TRACER console or by any DMX 512 controller.
As shown in the figure, the TRACER FOLLOWSPOT 1200 is made up of the following parts:
1. Front opening
2. Upper lid
3. Projector body
4. “4 zoom system” control
5. Lamp compartment
6. Bracket adjustment
7. Adjustable bracket
8. Cooling unit
9. Bar adjustment
10. TRACER control unit on-board
11. TRACER console
12. Reclining rear bar
TECHNICAL FEATURES AND DIMENSIONS
Voltage rating 230 V Rated current 7,4 A
Inductive current 3,5 A Absorbed power 1600 W
Frequency 50 Hz Maximum room temperature 35° C
Maximum surface temperature 70° C Distance from inflammable surface 1,5mt
Main mount via # 1 screw M12 Projector body length 840 mm
Max. length complete with bar 1155 mm Width including bracket and handles 360 mm
Weight of the complete projector 44.8 kg Weight, included packaging 50 kg
2
REAR PANEL
As shown in the figure, the following elements ca be seen on the rear panel:
1. Rear handle
2. Serial number plate
3. DMX address area
4. Control Assignment Section
5. XLR DMX 512 in/out
6. Line and electronic fuse
7. Main power supply cable
8. ON/OFF lamp switch
9. RS232 for TRACER console
10. Gobos selection (only TRACER 2)
11. Lamp hour counter
ADJUSTMENT OF PROJECTOR BODY ANGLE AND REAR BAR
As shown in the figure, in order to be able to control manually the movement of the vertical axis, it’s sufficient to
loosen the knobs “A”. Thanks to the innovative reinforced bracket with teflon coated disks, you can avoid hard
adjustments and obtain smooth movement and perfect stability of the product, even in case of “release”. The
movement, enabled by the support bracket, is +/- 45° compared to the assembly position of the bracket.
In order to recline the rear bar into the desired position it is necessary to loosen the knob “B”. When the new
positioning has been made, we suggest to tighten firmly the knobs and to verify that the locking is well done before
operating directly with the projector.
WORKING POSITION
TRACER FOLLOWSPOT 1200 can work in all positions.
MECHANICAL SAFETY GUARDS
A bipolar cut-off switch is located between the lamp compartment and the cooling unit. This safety switch cuts off
the power to the projector if the top lid is opened.
NOISE LEVEL
After the projector has been powered up and the initial configuration takes place, the noise produced by the
projector is primarily due to its cooling system. The noise level is much lower than the limit of 70 db as permitted by
law.
3
PACKING
The projector is shipped and delivered in a cardboard box made of KRAFT cardboard and semi-chemical additivefree paper, in compliance with BSFV Class 3 standards for waste disposal.
The projector is completely assembled, placed in the box inside a polyethylene bag and held firmly in place with
polyurethane foam packing material. The box is stapled shut.
Even though the packing provides complete protection from rain, it must not be exposed to inclement weather or
humidity.
No more than three identical boxes can be stacked one on top of the other.
STORAGE
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and
+50°C.
HANDLING
The projector, with or without packing, must be handled with care.
Lifting and handling must be carried out with special equipment. Do not expose the projector, with or without its
packing, to brusque accelerated or decelerated movements, knocks, dragging, or other stress caused by
unsuitable handling.
The projector in its packing can be seriously damaged if it falls or suffers a blow during transportation.
HANDLE WITH CARE!
ADMISSIBLE ENVIRONMENTAL CONDITIONS
The projector was engineered and produced to function in covered dry areas with an air temperature ranging
between 0° and 35° C, and with a humidity level between 30 and 90%.
Sharp changes in room temperature may generate condensation inside the projector which can harm the projector.
Therefore, switch on the projector only after it has undergone a period of gradual adaptation to the room
temperature.
4
START – UP PROCEDURES
POSITIONING AND INSTALLATION
Follow these steps for opening the package and installing the projector in its working position:
• Place the projector near the place it will be installed.
• Open the package and remove the anchoring elements, accessories, and user manual.
• Carefully read the instructions in the manual.
• Arrange tripod or stand or any other adequate support.
• In case of tripod or stand, position the projector on an horizontal plane and mount before the rotation pivot
in the middle of the adjustable bracket.
• Using and adequate lifting equipment, complete the mounting on the stand or any other adequate support.
• Tighten the M12 bolts and insert a device to prevent them from accidentally loosening.
• Make sure all adjustable parts are locked firmly in place in the desired position.
You must verify the stability of the support elements when the projector is in working condition.
Do not install the projector where there are objects located at a distance of less than 20 centimetres from
the cooling unit.
POWER SUPPLY
The power line must be protected by a differential magneto thermal circuit breaker, while using the followspot, be
sure not to pull the cable. TRACER 1200 absorbs 1600 W at 230 V.
Connect the fixture to the mains with the enclosed power cord and plug. See the table for the colours of
the connection-cable.
When in doubt, consult a qualified electrician.
Be careful with your operations. With a high voltage you can suffer a dangerous electric shock when
touching the wires! Inside the projector, the ignitor circuit have very high voltage, over 5Kv.
The User must ensure that the power supply is provided with a highly sensitive differential circuit breaker
30m/A to protect the projector from indirect contacts, and that the grounding system PE is working
properly.
Don’t power the projector with a dimmer circuit
5
LAMP INSTALLATION
• Loosen the knobs on the top lid and remove it.
• Remove the lamp from the packing and carefully read the
manufacturer’s instructions.
• LAMP MSR 1200W: Insert the lamp into the ceramic socket.
• LAMP HMI 1200: Loosen the two ring nuts at both end of the
lamp.
Place the lamp in its socket. Make sure the protuberance of the
central bulb is facing downwards to avoid creating shadows in
the projection. Tighten the two ring nuts on the lamp.
• Replace the top lid and firmly tight the knobs.
• Regulate the LAMP, with screws, if necessary.
CONTROL UNIT
TRACER FOLLOWSPOT 1200 comes with a control unit mounted on the adjustable bar and connected to the
projector by means of a proper cable through 9 pin din connector. The TRACER CONTROL UNIT is powered at
low voltage 12 Volts directly by the projector and it is able to control the fixture in all its functions.
It is necessary to know that TRACER FOLLOWSPOT 1200 can be controlled by practically all types of controllers
on the market that can execute the standard DMX 512 protocol. Controller-projector and projector-projector
connections require a two-core screened cable provided with CANNON PLUGS AND SOCKETS. TRACER can
use both 3 or 5 pin CANNON plugs and sockets because it comes with 3- and 5 pin CANNON SERIAL PORTS.
The ground braid on the screened cable must be connected to just one end of the cable. The projector and cables
must not be installed near overhead ducts for electrical cables or intense magnetic fields.
PROJECTOR ADDRESS
To make sure the projector functions properly , the dip-switches in the DMX ADDRESS AREA on the rear panel
must be correctly configure. Keep in mind that each TRACER FOLLOWSPOT 1200 occupies 6 DMX channels.
Each projector must be set separately on its own BASE CHANNEL (or STARTING CHANNEL) . The BASE
CHANNEL assignment is obtained by summing the values for each switch in the DMX SECTION (for example, to
set a projector on BASE CHANNEL #39, you must set dip-switches 32,4,2 and 1 to the ON position, because
32+4+2+1= 39). In the Standard Operating Mode, this means the TRACER FOLLOWSPOT 1200 will receive
signals on 6 channels following the BASE CHANNEL, BASE CHANNEL included (for example, if the projector is
set on BASE CHANNEL #39, it will receive signals on channels #39, 40, 41, 42, 43 and 44)
6
WHAT’S INSIDE
COLOUR WHEEL
TRACER has n°1 motorized colour wheel with n°7 adjacent dichroic filter plus open (White – Red – Yellow –
Magenta - Green – Orange – Pink).
GOBOS WHEEL (only TRACER 2)
TRACER 2 has n°1 wheel with n°4 metal gobos (interchangeable) plus open.
To change the gobos, follow these steps:
• Disconnect the power supply.
• Wait at least 20 minutes to be sure the projector components are cold.
• Loosen the knobs on the top lid and remove it.
• Choose the pattern you want to replace and delicately press on it to extract it from a fastening clip.
• Choose another gobo, use standard M-size gobos.
• Insert the new pattern inside the clips.
• Replace the top lid and firmly tight the knobs.
EFFECT WHEEL
TRACER has n°1 motorized effect wheel with CTO filter, CTB filter and Frost filter for soft beam.
FOCUS LENS
TRACER has n°1 motorized focusing coated lens, for high definition projection.
ZOOM WHEEL
TRACER has manual multi step zoom, N°1 wheel with lenses to obtain n°4 different beam angle.
SHUTTER
TRACER has n°2 shutter for dimmer and strobe effect
7
DMX CHANNEL ASSIGNMENT
CHANNEL FUNCTION
01 COLOUR
02 COLOUR CORRECTION
03 IRIS
04 DIMMER & SHUTTER
05 FOCUSING
06 SPECIAL FUNCTION
The projector can receive the signal from any DMX CONTROLLER and from the TRACER CONSOLE at the
same time. The dip switches of the control assignment section set on OFF are controlled by the DMX
CONTROLLED. The dip switches of the control assignment section set on ON are controlled by the
TRACER CONSOLE. Do not remove the TRACER console
When using the projector with a standard DMX controller, the channel to be used is n°2 or higher.
When you address a projector keep in mind that the BASE CHANNEL (or Starting Channel) corresponds to
the first channel (the colour channel, in this case), and the other functions follow in the order described in
the table.
8
CHANNEL 1 = COLOURS
percent values decimal values
0 > 5.9 % WHITE 0 > 15
6.3 > 9.4 % WHITE / RED 16 > 24
9.8 > 13.3 % RED 25 > 34
13.7 > 18 % RED / YELLOW 35 > 46
18.4 > 21.6 % YELLOW 47 > 55
22 > 25.5 % YELLOW / MAGENTA 56 > 65
25.9 > 29.8 % MAGENTA 66 > 76
30.2 > 33.7 % MAGENTA / GREEN 77 > 86
34.1 > 37.3 % GREEN 87 > 95
37.6 > 41.6 % GREEN / ORANGE 96 > 106
42 > 45.9 % ORANGE 107 > 117
46.3 > 49.8 % ORANGE / BLUE 118 > 127
50.2 > 53.3 % BLUE 128 > 136
53.7 > 57.3 % BLUE / PINK 137 > 146
57.6 > 61.6 % PINK 147 > 157
62 > 65.9 % PINK / WHITE 158 > 168
66.3 % MIN RAINBOW SPEED =169
66.3 > 100 % INCREASING RAINBOW SPEED 169 > 255
100 % MAX RAINBOW SPEED =255
CHANNEL 2 = COLOURS CORRECTION
percent values decimal values
0 > 19.2 % OPEN 0 > 49
19.6 > 38.8 % CTO (CORRECTION ORANGE) 50 > 99
39.2 > 58.4 % FROST FILTER 100 > 149
58.8 > 78.0 % CTB (CORRECTION BLUE) 150 > 199
78.4 > 100.0 % FROST FILTER 200 > 255
CHANNEL 3 = IRIS DIAPHRAGM
percent values decimal values
0 % > 2.4 % CLOSED 0 > 6
2.7 % > 100 % INCREASING DIAMETER 7 > 255
100 % OPEN =255
CHANNEL 4 = DIMMER & SHUTTER
percent values decimal values
0 % BLACK-OUT =0
0 % > 52.5 % LIGHT LEVEL, FROM 0 TO MAX 0 > 134
52.9 % STROBE EFFECT MIN SPEED =135
52.9 > 95.3 % INCREASING RAINBOW SPEED 135 > 243
95.3 % STROBE EFFECT MAX SPEED =243
96.1 % > 100 % OPEN (MAX LIGHT LEVEL) 245 > 255
CHANNEL 5 = FOCUSING
percent values decimal values
0 % MAX FOCUS =0
0 > 100 % adjustable focus from FAR to NEAR 0 > 255
100 MIN FOCUS =255
CHANNEL 6 = SPECIAL FUNCTION
percent values decimal values
0 > 29.4 % LAMP OFF (AFTER 20 SEC.) 0 > 75
44.7 > 54.9 % RESET (AFTER 5 SEC.) 114 > 140
71 > 100 % LAMP ON (INSTANT) 181 > 255
NOTE: (In standard version of TRACER, the LAMP is permanent ON)
9
CONTROL SYSTEMS
CONTROL FROM TRACER CONTROL UNIT
In this mode, the projector is controlled directly from the on-board TRACER control unit.
To better understand the working, we suggest to read carefully this paragraph and, if possible, to operate step by
step directly on the TRACER console or to refer to the TRACER console drawing.
COLOUR SECTION
Colours are controlled from here.
Quick- select keys can be used to project the corresponding colour.
Two-colour beams are projected when two adjacent keys are pressed simultaneously.
When the Rainbow/Fixed Colours key is pressed, the projector will do the rainbow effect. Rotation speed is
controlled by the colour section slider when the Rainbow LED is switched on. This function may be switched off by
pressing the Rainbow/Fixed Colours key again or any of the quick-select COLOUR keys.
FILTER CORRECTION SECTION
Temperature correction filters and frost filter are controlled from here.
The colour temperature correction filter keys is used to set primary colours (5600°K), warm colours (3200°K CTO)
or cold colours (6500°K CTB). The FROST filter key is used to obtain soft beam using.
DIMMER /SHUTTER SECTION
This section contains the controls for light beam characteristics: INTENSITY, my means of the DIMMER, and
STROBE EFFECT, using the variable speed SHUTTER.
Note that the action of the slider for this section depends on the position of the Dimmer/Strobe selector. When the
Dimmer LED is on, the slider adjusts the intensity of the beam. When the Strobe LED is on, the slider controls the
strobe effect speed.
The two Blackout keys on both sides of the DIMMER / SHUTTER SECTION open or close the shutter
instantaneously. This function has priority over the other keys in this section, when the black-out function is active
the LED over the two blackout keys flashes.
When the blackout LED is flashing, just press any one of the two blackout keys and the projector will return to
either dimmer or strobe status (depending on the position of the dimmer/strobe selector).
10
IRIS SECTION
This section provides beam DIAMETER controls.
Beam diameter is controlled directly with the slider. The beam is blocked completely when the slider is set to 0.
Press the Open key to open or close the iris immediately. The beam can be opened to the desired diameter using
the slider.
FOCUS SECTION
By pressing one of two keys (“+” or “-“), the beam can be perfectly focused at the desired distance.
SPECIAL FUNCTION
Tracer function, as the name suggest, concerns the beam positioning.
HOW IT WORKS: when the blackout key is pressed, the Blackout and Tracer LED flash simultaneously. In fact, the
TRACER function only works when the projector is in BLACKOUT mode.
At this point, when the TRACER key is pressed and held down, the IRIS is at the minimum aperture and the
DIMMER starts opening at minimum speed. In this phase the TRACER key directly controls the dimmer.
Keeping the key pressed, light intensity increases, When the key is released, intensity decreases, As a result, the
operator can easily get exactly the right intensity for undetectable tracing.
Once the projector has been correctly positioned, simply pressing the Blackout key the beam instantly is on target
with the preset light intensity and beam diameter.
CASCADE CONTROL FROM THE TRACER CONSOLE
When several projectors are connected by cable, the console on the first projector can control all functions on the
following projectors. For this reason, the projectors must be connected with a standard DMX cable, IN/OUT 3 or 5
pin connectors. Each projector must have its own TRACER console connected.
This system can be used to control an indefinite number of projectors in perfect synchronism.
FIRST MASTER: all the dip switches of the control assignment section and the dmx address area must be set on
OFF, but the dip switch nr. 7 of the control assignment section set on ON.
OTHER SLAVES: all the dip switches of the control assignment section and the dmx address area must be set on
OFF, but the dip switch nr. 1 of the dmx address area set on ON.
11
CASCADE CONTROL FROM ANY DMX 512 LIGHTING DESK
This control system is identical to the previous one with the only difference that all projectors must be set to SLAVE
mode (all 5 DIP-SWITCHES of the CONTROL ASSIGNMENT SECTION set to OFF).
MIXED CONTROL
Mixed control means that the projectors are driver by any DMX console, but allows the operator to decide the
functions to use directly from the projector.
The projector can receive the signal from any DMX CONTROLLER and from the TRACER CONSOLE at the same
time. The dip switches of the control assignment section set on OFF area controlled by the DMX CONTROLLED.
The dip switches of the control assignment section set on ON area controlled by the TRACER CONSOLE.
12
OPTICAL SYSTEM
TRACER 1200 is provided with a efficiency optical system, double condenser with mirror and coated lenses. This
system lets TRACER FOLLOWSPOT 1200 project an extremely powerful and homogenous light beam.
The TRACER FOLLOWSPOT 1200 is furnished with a 4 - lenses system that lets you create beams of different
sizes. This system consists of a wheel (as shown in the figure) with four different positions. It is a kind of manual
zoom that let TRACER produce beams of different sizes. The 4 OBJECTIVES system makes TRACER the most
versatile projectors in its range. From 10 to 50mt.
With projector ON, in order to obtain the desired beam aperture, it sufficient to act on the control knob of the “4
objectives system”, visible on the picture and located on the side of the projector body
The graphs show the beam amplitudes for the different choices, The details of the positions as described in the
drawings may be subject to change. Therefore, please refer to the indications printed directly on the wheel of the
optional lenses.
10° is the plus luminous beam of the 4 aperture.
13
MAINTENANCE
Safety guards, lenses and filters must be replaced if they are visibly damaged to the point that they
become ineffective (i.e.: if they have deep slashes or cuts)..
The lamp must be replaced if damaged, cracked or deformed by the heat
PLANNED MAINTENANCE
OPERATION FREQUENCY RESPONSIBLE ACTION
Optical efficiency test
Lamp replacement
Surface temperature test
Cleaning
Testing for safety breaker circuit
on general electric system
Check damage to cables due to
mobile use projector
General service check of projector
750 hours User
Max 800 hours " "
Quarterly " "
Every two months " "
Monthly " "
Once a year " "
Every two years Authorized technician
Check life-saving safety device by
pressing its "T" bottom
Replace cable if damage
M1
M2
M3
M4
Always use original spare parts to ensure safe and proper functioning of the projector.
Do not make changes to the projector. A modified projector requires a new CE marking
M1 OPTICAL EFFICIENCY TEST
Use the controller to focus the beam on a flat surface, keeping the Iris and Dimmer at 100%. If the spot is not
homogeneous, follow these steps:
• Remove knob A, making sure the projector keeps its current position.
• Insert a screw driver in the hold and turn clockwise or counter clockwise to optimise the horizontal position
of the lamp compared to the optical system.
• Replace the knob A and firmly tighten.
• Remove the PVC plug on the bottom of the projector. Insert a screw driver in the hole and turn it clockwise
or counter clockwise to optimise the vertical position of the lamp compared to the optical system.
• Replace the plug.
M2 LAMP REPLACEMENT
The lamp must be replaced with the same type of lamp and according to the same frequency. A less efficient lamp
jeopardizes projector performance. Replace the lamp as follows:
• Loosen the knobs on the top lid and remove the lid.
• Remove the lamp from the packing and carefully read the Manufacturer’s instructions.
• LAMP MSR 1200W: Insert the lamp into the ceramic socket.
• LAMP HMI 1200: Loosen the two ring nuts at both end of the lamp. Place the lamp in its socket. Make sure
the protuberance of the central bulb is facing downwards to avoid creating shadows in the projection.
Tighten the two ring nuts on the lamp.
• Replace the top lid and firmly tighten the knobs.
• Regulation the LAMP, with screws, if necessary.
• Switch on the projector to make sure the lamp is working correctly.
14
M3 SURFACE TEMPERATURE TEST
Before you check the temperature, make sure the projector is in its full operating mode (wait about 20 minutes after
switching on the projector). Use a contact probe to measure the surface temperature on the projector’s metal case
and determine the hottest area.. The temperature must be less than 70° C. Otherwise, check the cooling system.
M4 CLEANING
Cleaning must be carried out when the projector is cool disconnected from the power supply with the general
power switch turned off, and the ON/OFF switch on the rear panel switched OFF.
FREQUENCY
It is recommended to clean the projector every two months to ensure efficiency and performance. If the projector is
used in particularly smoky or dusty sections, clean the projector more frequently.
CLEANING PROCEDURES
1 Open the top lid by unscrewing the knob and remove it from its seat.
2 Use a low power comprised air to remove dust.
3 Use a soft cloth (non fabric) and pH neutral (pH7 ) liquid detergent to clean mirror and lens surface. Make sure
you remove all residual traces. Never touch the lamp directly with your hands or materials that can leave greasy
traces.
4 Follow the same steps to clean the other internal parts of the projector.
5 Make sure the cleaning procedure did not damage any internal part or modified their correct position
6 Replace the top lid and firmly tight the knob.
If the projector is operated in ordinary working conditions and the user follows the planned maintenance operations
established by the Manufacturer, it should last for years.
When the projector is discarded, it must be disposed of according to recycling laws.
15
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Make sure the mains power is ON and the circuit breaker has
No mains power supply
Projector does not turn
ON
Lamp does not ignite Burned-out or faulty lamp Replace the lamp
The beam is not well
defined (Faulty
projection)
The projector does not
respond to controller
signals
Discontinuous
projector functioning
Noisy projector Mechanical wear
No power to projector
Burned-out fuse
An optical element is
damaged
Malfunctioning of the
electronic circuit
The lenses and mirrors
are dirty
In case of DMX control:
malfunctioning of the
DMX cable
In case of DMX control:
wrong addressing
Malfunctioning electronic
circuit
Malfunctioning motor or
transmission
Safety thermostat has
been triggered
Make sure the switch on the back of the projector is ON
Make sure the top lid is tightly closed
Replace the burned-out fuse* Use the type of fuse as
indicated on the side of the projector
Switch OFF the power and check mirrors and lenses. If
damaged call an authorized technician.
Contact an authorized technician
Switch OFF the power and clean the parts as explained in the
Replace the cable and check the line before switching ON again
Check the DMX section and CONTROL ASSIGNMENT section
and reconfigure the dip-switches correctly
Contact an authorized technician
Contact an authorized technician
Remove the dirt and check to see if the cooling system is
One or both fans stop functioning. Contact authorized technician
Identify the source of noise and remove the cause or contact an
*Before switching ON the projector, identify and remove the causes that made the safety fuse intervene.
not been triggered
cleaning paragraph
the projector
working properly
authorized technician
16
SPARE PARTS
When ordering spare parts for the projector remember to mention the model and serial number which can be found
on the plate at the rear of the projector.
Call your area dealer or feel free to contact the manufacturer for any additional assistance.
WARRANTY
TRACER is guaranteed against any manufacturing defects or material flaws. If defects or breakdowns occur during
the warranty period, the manufacturer, directly or through its agents. After inspection and according to its own
unquestionable judgment, the manufacturer will repair or replace the defective part.
No goods can be returned, for any reason without previous authorisation from the manufactured, and the transport
charges, to and from LAMPO are at the cost of the client.
The warranty is not valid in the following cases:
1 If the projector was used improperly or with negligence, or if it was damaged and repaired and/or modified to the
point of jeopardizing safe functioning.
2 If the projector is used in conditions other that those specified in this manual.
3 If non-original spare parts are used.
4 All malfunctioning and breakdowns caused by acts of God, negligence, and improper use, and parts subject to
wear are not covered by the warranty.
The improper use of this projector, cancel the guarantee and our responsibility. All the information have been
written and driven with extreme care; however, we do not engage us any responsibility for contingent errors or
omissions. We reserve the right to modify and/ or improve our product as we retain necessary, without subsequent
warning or notice. It is forbidden any complete or partial reproduction of this handbook, if not expressly authorized.
17
Loading...