SAGEM Wi-Fi 11g USB ADAPTER
Quick Start Guide
About this guide
This Quick Start Guide describes how to install and operate your SAGEM Wi-Fi 11g USB ADAPTER.
Please read this manual before you install the product.
Introduction
The SAGEM Wi-Fi 11g USB ADAPTER is a network adapter with a rate of 54 Mbps to 1 Mbps operating in
the 2.4 GHz band implementing the IEEE 802.11b/g standard.
Its USB port is USB 2.0 compliant
It fully supports wireless networking under Windows 98SE/ME/2000/XP.
The Wireless LAN (Local Area Network) USB adapter can be operated in one of the two following networking
configurations :
In this mode, the radio links are coordinated by an
1. Infrastructure Networking
Access Point enabling to access an existing wired
network and/or enabling to access to network
resources such as Internet, email, file transfer…
2. Ad-hoc Networking
Wireless Network
Also known as a peer to peer network, this mode
allows wireless to wireless connection, enabling all
workstations to act as servers to all others. This mode
can be used to share a printer or for file transfer.
Ad-hoc
Infrastructure
Wired Network
1
Package Content
These are the items included in the package:
♦ One SAGEM Wi-Fi 11g USB ADAPTER
♦ One USB Cable
♦ One Quick Start Guide
♦ One installation CD-ROM
Minimum System Requirements
♦ PC Computer with an available USB port.
♦ Compatible with USB 1.1 port
♦ Microsoft Windows 98 Second Edition, Windows Millennium, Windows 2000 or Windows XP installed
on the PC.
Installation of the Wireless LAN Software
The installation of your LAN USB adapter requires three steps:
♦ Installation of the software
♦ Installation of the hardware
♦ Configuration of the wireless connection
2
Installation of the software
Warning: It is necessary to install the Wireless LAN Software BEFORE to insert
the USB adapter in the appropriate USB port of your computer.
The first step consists in copying on your hard disk all the necessary files for your new equipment. For
that, please follow the next instructions:
1. Insert the Product CD-ROM into the CD-ROM drive of your computer.
2. An Auto-run is automatically executed and the
following screen comes up. If not, run the
Autorun.exe on the CD-ROM
The menu offers the following choices :
Install the Wireless LAN Utility and driver
Read the present manual
To launch the installation, click Wi-Fi adapter
install
A first screen shows up. Click Continue to continue. Follow the on-screen instructions to install the Wireless
LAN Utility.
When this screen shows up, go to the next
chapter to execute the hardware installation of
your SAGEM Wi-Fi 11g USB ADAPTER, then
click on OK.
Hardware Installation
After having copied all necessary files in the previous step, we will now connect the Wireless LAN.
Insert the USB connector of the adapter in an USB port
included in your package, if it is impossible to connect the USB adapter directly on your computer.
on your computer or use the USB cable
Important remark under Windows 98SE
♦ If the Please insert the disk labeled Windows 98SE/ME CD-ROM, and then click OK Window
appears, insert your Windows CD-ROM and enter the path corresponding to the CD-ROM drive then
click OK. Click Finish to complete the installation, which will restart Windows.
3
Configuration of your Wireless LAN USB to access to Internet
After the two previous steps completion, your Wireless USB LAN adapter is now installed. You now have to
configure your connection to be able to access via an access as seen below.
Client 2
Client 3
Client 1
Point
Access
INTERNET
To do that, you will have to:
♦ Launch the WLAN Utility management software
♦ Configure your adapter in Infrastructure Mode
♦ Set the SSID of the wireless network on which you want to attach
♦ Configure the encryption parameters if you want to protect your wireless network
Internet access configuration
At first, you must verify that the computer, where you have installed your USB adapter is configured in DHCP
(dynamic address) :
♦ In the Network Connection tab of the Control Panel menu, click on the TCP/IP protocol of the
Wireless network connection (SAGEM Wi-Fi 11g USB ADAPTER).
♦ Select Obtain an IP address automatically in the IP Address tab.
Open the WLAN utility
To open the WLAN utility, you have two possible choices:
♦ Select the SAGEM Wi-Fi 11g USB adapter LAN Utility from the Start
Menu of Windows,
♦ Or double-click the corresponding icon laying on the Windows desktop :
SAGEM Wi-Fi
11g USB adapter
LAN Utility
The‘ ’ icon then appears in the System Tray (in the bottom right corner of your task bar).
4
Double-click this icon and the main screen of
the Utility shows up as seen opposite.
Configuration of your Wireless LAN adapter in Infrastructure Mode
To access Internet your Wireless LAN adapter must be set in Infrastructure Mode as seen below.
In the main screen of the Utility, click the down arrow at the
right of the Network Type field and select Infrastructure
Selection of the SSID
The SSID is a string of characters identifying a wireless network (it is the name of this network). To belong to
a same wireless network, the client stations and the access point (connected to the Internet) have to use the
same SSID.
If you keep the SSID field to empty (default value), your
adapter will attach itself to the nearest access point (or to the
one sending the higher radio signal).
If you know the name of the access point you want to associate with, enter this SSID in the corresponding
field and then click Apply button to make the setting take effect. Or double click on Site Survey line where
your access point appear.
The SSID can be set up to 32 characters. It is case sensitive (please take great attention to that).
Configuration of the Encryption parameters
To prevent unauthorized wireless station from accessing data transmitted over your network, the Wireless
LAN adapter offers secures data encryption, like open and shared Key authentication with WEP (Wired
Equivalent Privacy) encryption or WPATKIP
(Temporal Key Integrity Protocol) encryption. The activation or not of the security has to be set on the
PSK (Wi-Fi Protected Access – Pre Shared Key) authentication with
same way on the Access Point and on your LAN USB adapter (client station).
Your network can only be operated in the 2 following conditions:
♦ No security activated, neither in the Access Point, neither in the client stations
♦ Security activated (recommended for securing your data) in the Access Point and on all client stations
with the same characteristics of encryption.
5
1) Security disabled on Access Point.
If your Access Point works without security, your wireless LAN adapter also has to be set without WEP.
Check in the main screen of the Utility that the Security Enabled check box is unchecked.
2) Security enabled on Access Point.
Beware that if you enable security on your adapter, you necessarily have to enable the type of security on
the Access Point side, as well, if you want your adapter to be able to associate with it. Go the Configuration
tab in the main screen of the Utility and activate the Security Enabled check box.
The Security window then shows up.
Here we will explain how to configure open security with WEP and WPA-PSK security with TKIP.
2.1) WEP encryption :
In the window Security, you will have to :
♦ select authentication : Open
♦ encryption is fix to WEP
♦ disable IEEE 802.1X authentication mode
♦ select the WEP type : 64 bits or 128 bits
♦ select the index key
♦ select the way to generate the encryption keys (from a passphrase or manually)
Length of the WEP keys
WEP protocol offers two levels of encryption: encryption based on 40 or 64 bits key length and more secure
encryption based on 104 or 128 bits key length.
The
40 bits keys and the 64 bits keys are the same, if their effective length is 64 bits, only 40 bits are
selected by the user, the others bits are automatically calculated. Speak about 40 bits keys or 64 bits keys is
the same thing. It is identical for the 104 and 128 bits keys.
The principle of management is identical for both 64 bits and 128 bits.
The key length has to be set at the same value on the Access Point and on the client station (Wireless LAN
adapter in our case).
Creation of the WEP keys
It is possible to manually enter the WEP key you want to use. However, this entry being rather tedious,
especially for 128 bit keys, it is possible to have them generated automatically. To do that, you will have to
enter a string of characters called "Passphrase".
6
Create Encryption Keys by Using a Passphrase
1- Select first the 64 bits or 128 bits length of the
key.
2-
Select in key format : Passphrase.
3-
Select index key
4- Enter the string in Network key and Confirm
network key. The key is generated from your
string.
5-
Finally click the Apply button in the
Configuration tab to save the configuration.
Warning: when Create Key with Passphrase is enabled, the wireless device’s Key number with
PassPhrase must match the Key number with PassPhrase used by the access point with which wireless
devices are going to communicate.
Create Encryption Keys Manually
You can also create up a encryption key.
1. Select first the 64 bits or 128 bits length of the key to
generate
2. Select ASCII or Hexadecimal
3. Select index key
4.
Enter manually the key you want in the key field taking in
account the remarks here after specifying the authorized
characters
5.
Finally click the Apply button in the Configuration tab
to save the configuration and make setting take effect.
For 64 bits encryption you may choose:
• Alphanumeric: 5 characters (case sensitive) ranging from a-z, A-Z and 0-9 (e.g. MyKey)
• Hexadecimal: 10 hexadecimal digits in the range of A-F, a-f and 0-9 (e.g. 11AA22BB33)
For 128 bits encryption you may choose:
• Alphanumeric: 13 characters (case sensitive) ranging from a-z, A-Z and 0-9
(e.g. MyKey12345678)
• Hexadecimal: 26 hexadecimal digits in the range of A-F, a-f and 0-9
(e.g. 00112233445566778899AABBCC).
7
2.2) WPA-PSK / TKIP encryption:
1 - Select authentication mode : WPA-PSK
2 – Select encryption mode : TKIP.
3 – Enter a string from 8 to 63 characters or a 64
hexadecimal characters key in Network key and
Confirm network key
4 - Select OK to close Privacy configuration.
5 - select Apply button in the Configuration tab to
save the configuration and make setting take effect.
.
The configuration of your Wireless LAN adapter to access to Internet under Windows is finished
Configuration of your Wireless LAN adapter in Ad Hoc mode
Also known as a peer to peer network, this mode allows wireless to wireless connection, enabling all
workstations to act as servers to all others. This mode can be used to share a printer or for file transfer.
Client 2
Client 1
Client 3
8
Configuration of Network Type
To set your Wireless LAN adapter in the Ad Hoc mode, click the down arrow at the right of the Network Type
field and select Ad Hoc in the main screen of the WLAN utility.
Configuration of the SSID
The SSID is a string of characters identifying your wireless network (it is the name of this network).To be part
of a same network, wireless clients must have the same SSID. This SSID is the name of this network.
If you want to associate to an existing Ad Hoc network, enter
the SSID of this network in the corresponding field (replacing
ANY) and click the Apply button on the Configuration tab to
make the setting take effect.
If you want to create a new Wireless Ad Hoc network, enter an unused SSID to identify your own network.
Then click the Apply button on the Configuration tab to make the setting take effect.
Configuration of the Channel
To be part of a same network, wireless clients must use the same channel If you want to associate to an
existing Ad Hoc network, select the channel of this network in the corresponding field AdHoc Channel in the
main screen of the WLAN utility. Then click the Apply button on the Configuration tab to make the setting
take effect.
If you want to create a new Wireless Ad Hoc network
on the Configuration tab to make the setting take effect.
Configuration of WEP encryption
The configuration of WEP encryption in Ad Hoc mode is similar to the one in Infrastructure Mode. Please
refer to the above explanations.
The configuration of your Wireless LAN adapter in Ad-Hoc mode is finished.
, select an unused channel, then click the Apply button
About Status Information on your Wireless LAN USB
adapter LED Indicator
The SAGEM Wi-Fi 11g USB ADAPTER has one LED indicator giving the following informations on the link
status:
♦ Solid Green: Connected to an Access Point or Ad-Hoc wireless workstation and
transmitting data.
♦ Blinking Green: Attempting connection to the Access Point or Ad-Hoc wireless workstation
Icon of the WLAN utility
The color behind the system tray icon indicates the link status :
Blue indicates a good or excellent link.
Yellow indicates a usable but weak link.
9
Red indicates very poor link quality.
Red and exclamation mark indicates no link.
Status field on the Configuration Menu of the WLAN utility
The Status field on the Configuration menu provides more detailed information.
State : When operating in Infrastructure mode, this field shows the MAC address of the
Access Point with which the SAGEM Wi-Fi 11g USB ADAPTER is communicating.
When operating in Ad-Hoc mode, it shows the virtual MAC address used by computers
participating in the Ad-Hoc network.
Current Channel : Shows the radio channel on which the connection is made.
Current Tx Rate : Shows the highest transmit rate of the current 54 Mbps to 1 Mbps.
Throughput : Shows the short term transmit and receive throughput in packets/second, and is
continuously updated.
Link Quality : Based on the quality of the received signal
Signal Strength : Based on the received radio signal strength.
Uninstall the Wireless LAN adapter
1. To remove the Wireless LAN Utility from your computer, go to the Start menu and select Uninstall
SAGEM Wi-Fi 11g USB adapter LAN Utility .
2. Follow the instructions on the different screens to uninstall the Wireless Utility then click Finish.
3. Now you can disconnect your SAGEM Wi-Fi 11g USB ADAPTER.
10
Troubleshooting
If you experience any difficulty resolving the problem while installing or using the SAGEM Wi-Fi 11g USB
ADAPTER, please contact the supplier for support.
Problem Solution
At SAGEM Wi-Fi 11g USB ADAPTER
installation, Windows was unable to
locate the driver for this device.
The Wireless LAN adapter LED does
not come on.
The Wireless LAN adapter LED
flashes and you cannot access to your
Access Point or to the other client
stations of your network.
After a restart of your computer (PC or
Mac), the system cannot detected the
Wireless LAN adapter plug into it.
All rights reserved Copyright 2006 Sagem Communication PARIS France
• Restart your PC and follow the screens showed up.
• Check that the Wireless LAN adapter is correctly connected.
• Plug out the Wireless LAN adapter, then plug in it into the same
USB port on your computer.
• Under Windows check the Wireless LAN adapter driver is
correctly installed. If this is not the case uninstall then reinstall the
driver.
• Check that the SSID and the WEP encryption keys are the same
on the computers and the access point which are on the same
network.
• Check that the wireless network is operational.
• Plug out the Wireless LAN adapter, then plug in it into the same
USB port on your computer.
Ref. 252516540
11
Loading...