Sagem WUBR-128GW DONGLE WIFI, WL167G DONGLE WIFI User Manual

Page 1
SAGEM Wi-Fi 11g USB ADAPTER
Quick Start Guide
About this guide
This Quick Start Guide describes how to install and operate your SAGEM Wi-Fi 11g USB ADAPTER.
Please read this manual before you install the product.
Introduction
Its USB port is USB 2.0 compliant
It fully supports wireless networking under Windows 98SE/ME/2000/XP.
The Wireless LAN (Local Area Network) USB adapter can be operated in one of the two following networking configurations :
In this mode, the radio links are coordinated by
1. Infrastructure Networking
2. Ad-hoc Networking
Wireless Network
Infrastructure
an Access Point enabling to access an existing wired network and/or enabling to access to network resources such as Internet, email, file transfer…
Also known as a peer to peer network, this mode allows wireless to wireless connection, enabling all workstations to act as servers to all others. This mode can be used to share a printer or for file transfer.
Ad-hoc
Wired Network
1
Page 2
Package Content
These are the items included in the package:
One SAGEM Wi-Fi 11g USB ADAPTER
One USB Cable
One Quick Start Guide
One installation CD-ROM
Minimum System Requirements
PC Computer with an available USB port.
Compatible with USB 1.1 port
Microsoft Windows 98 Second Edition (98SE), Windows Millennium (ME), Windows 2000
or Windows XP installed on the PC.
Installation of the Wireless LAN Software
The installation of your LAN USB adapter requires three steps:
Installation of the software
Installation of the hardware
Configuration of the wireless connection
I. Installation of your LAN USB adapter under Windows :
I.1 Installation of the software
Warning: It is necessary to install the Wireless LAN Software BEFORE to insert
the USB adapter in the appropriate USB port of your computer.
The first step consists in copying on your hard disk all the necessary files for your new
equipment. For that, please follow the next instructions:
1. Insert the Product CD-ROM into the CD-ROM drive of your computer
2
.
Page 3
2. An Auto-run is automatically executed and the following screen comes up. If not, run the Autorun.exe” on the CD-ROM
Select in the list your adapter model.
Please, read the model information directly on your equipment label.
The menu offers the following choices :
Install the Wireless LAN Utility and
driver
Read the present manual
To launch the installation, click Wi-Fi
adapter install”
A first screen shows up. Click Continue” to continue. Follow the on-screen instructions to install the Wireless LAN Utility. You may need to restart your computer. You may need to restart your computer.
I.2 Hardware installation of the SAGEM Wi-Fi 11g USB ADAPTER
After having copied all necessary files in the previous step, we will now connect the Wireless LAN.
Insert the USB connector of the adapter in an USB port cable included in your package, if it is impossible to connect the USB adapter directly on your computer.
3
on your computer or use the USB
Page 4
Important remark under Windows 98SE
If the “Please insert the disk labeled “Windows 98SE/ME CD-ROM”, and then click “OK”
Window appears, insert your Windows CD-ROM and enter the path corresponding to the CD­ROM drive then click “OK”. Click “Finish” to complete the installation, which will restart Windows.
Configuration of your Wireless LAN USB to access to Internet
After the two previous steps completion, your Wireless USB LAN adapter is now installed. You now have to configure your connection to be able to access via an access as seen below.
Client 2
Client 3
Client 1
Point
Access
INTERNET
To do that, you will have to:
Launch the WLAN Utility management software
Configure your adapter in Infrastructure Mode
Set the SSID of the wireless network on which you want to attach
Configure the encryption parameters if you want to protect your wireless network
I. Configuration to access to Internet under Windows :
At first, you must verify that the computer, where you have installed your USB adapter is configured in DHCP (dynamic address) :
In the Network Connection tab of the Control Panel menu, click on the TCP/IP protocol
of the Wireless network connection (SAGEM Wi-Fi 11g USB ADAPTER).
Select Obtain an IP address automatically in the IP Address tab.
4
Page 5
Open the WLAN utility
To open the WLAN utility, you have two possible choices:
Select the « Sagem Utiliy \ WLAN Card \ Sagem WLAN Control
Center » from the Start Menu of Windows,
Or double-click the corresponding icon laying on the Windows
desktop :
The‘ ’ icon then appears in the System Tray (in the bottom right corner of your task bar).
Double-click this icon and the main screen of the Utility shows up as seen opposite.
Sagem WLAN Control Center
Configuration of your Wireless LAN adapter in Infrastructure Mode
To access Internet your Wireless LAN adapter must be set in Infrastructure Mode as seen below.
In the left screen click on Config icon. Now, in Basic sheet select
“Infrastructure” as Network type
Selection of the SSID
The SSID is a string of characters identifying a wireless network (it is the name of this network). To belong to a same wireless network, the client stations and the access point (connected to the Internet) have to use the same SSID.
Enter the name of the access point you want to associate in the Network
Name (SSID) field and then click “Apply” button to make the setting
take effect.
5
Page 6
The SSID can be set up to 32 characters. It is case sensitive (please take great attention to that).
Configuration of the Encryption parameters
To prevent unauthorized wireless station from accessing data transmitted over your network, the Wireless LAN adapter offers secures data encryption, like “open” and “shared Key” authentication with WEP (Wired Equivalent Privacy) encryption or WPA­Shared Key) authentication with TKIP (Temporal Key Integrity Protocol) encryption. The activation or not of the security has to be set on the same way on the Access Point and on your LAN USB adapter (client station).
Your network can only be operated in the 2 following conditions:
No security activated, neither in the Access Point, neither in the client stations
Security activated (recommended for securing your data) in the Access Point and on all client
stations with the same characteristics of encryption.
1) Security disabled on Access Point.
If your Access Point works without security, your wireless LAN adapter also has to be set without security. Check in the Encryption screen of the Utility that the Network Authentication is set to open and Data encryption is set to Disable.
PSK (Wi-Fi Protected Access – Pre
6
Page 7
2) Security enabled on Access Point.
Beware that if you enable security on your adapter, you necessarily have to enable the type of security on the Access Point side, as well, if you want your adapter to be able to associate with it. Go to the Encryption tab in the Config screen of the Utility to set the security.
Here we will explain how to configure open security with WEP and WPA-PSK security with TKIP.
2.1) WEP encryption :
In the window ” Encryption ”, you will have to :
select authentication : Open
set encryption to WEP
select the key format : ASCII characters or hexadecimal digits
select the key length : 64 bits or 128 bits
select the default index key
select the way to generate the encryption keys (from a automatic or manual)
Length of the WEP keys
WEP protocol offers two levels of encryption: encryption based on 40 or 64 bits key length and more secure encryption based on 104 or 128 bits key length.
40 bits keys and the 64 bits keys are the same, if their effective length is 64 bits, only 40 bits
The are selected by the user, the others bits are automatically calculated. Speak about 40 bits keys or 64 bits keys is the same thing. It is identical for the 104 and 128 bits keys.
The principle of management is identical for both 64 bits and 128 bits.
The key length has to be set at the same value on the Access Point and on the client station (Wireless LAN adapter in our case).
Creation of the WEP keys
It is possible to manually enter the WEP key you want to use. However, this entry being rather tedious, especially for 128 bit keys, it is possible to have them generated automatically. To do that, you will have to enter a string of characters called "Passphrase".
7
Page 8
Create Encryption Keys by Using a automatic generation “Passphrase”
1- select authentication to Open
2- Set encryption to WEP
3- Select first the “64 bits” or ”128
bits” length of the key.
4- Select “ASCII” or “Hexadecimal”
5-
Select Automatic Generation
and enter the key string in passphrase
6- Select the default key index
Finally click the “Apply”button
7-
to save the configuration in profile
8-
use “Save Configuration” button
To quit click “OK” button.
9-
Warning: when Create Key with Passphrase is enabled, the wireless device’s Key number with PassPhrase must match the Key number with PassPhrase used by the access point with which wireless devices are going to communicate.
Create Encryption Keys Manually
1.
Set encryption to WEP
2.
Select authentication to Open
3. Select first the “64 bits” or “128 bits” length of the key to generate
4. Select “ASCII” or “Hexadecimal”
5. Enter manually the key you want in the corresponding index key field taking in account the remarks here after specifying the authorized characters
6.
Select the default key index
7.
Finally click the “Apply”button
8.
To save the configuration in profile use “Save Configuration” button.
9. To quit click “OK” button.
Note: You can also create up to 4 encryption keys.
8
Page 9
For 64bit encryption you may choose:
Alphanumeric: 5 characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g. MyKey)
Hexadecimal: 10 hexadecimal digits in the range of “A-F”, “a-f” and “0-9” (e.g. 11AA22BB33)
For 128bit encryption you may choose:
Alphanumeric: 13 characters (case sensitive) ranging from “a-z”, “A-Z” and “0-9” (e.g.
MyKey12345678)
Hexadecimal: 26 hexadecimal digits in the range of “A-F”, “a-f” and “0-9” (e.g.
00112233445566778899AABBCC).
2.2) WPA-PSK / TKIP encryption:
1 - Select authentication mode : WPA­PSK
2 – Select encryption mode : TKIP.
3 – Enter a string from 8 to 63 characters or a 64 hexadecimal characters key in Network key.
4 – Finally click the “Apply”button
5 – To save the configuration in profile use “Save Configuration” button.
6 – To quit click “OK” button.
The configuration of your Wireless LAN adapter to access to Internet under Windows is finished
9
Page 10
Configuration of your Wireless LAN adapter in Ad Hoc mode
Also known as a peer to peer network, this mode allows wireless to wireless connection, enabling all workstations to act as servers to all others. This mode can be used to share a printer or for file transfer.
Client 1
Client 3
Client 2
I. Configuration in Ad Hoc mode :
Configuration of Network Type
To set your Wireless LAN adapter in the Ad Hoc mode, click the down arrow at the right of the Network Type field and select “Ad Hoc” in the Basic sheet of the Config screen of the WLAN utility.
Configuration of the SSID
The SSID is a string of characters identifying your wireless network (it is the name of this network).To be part of a same network, wireless clients must have the same SSID. This SSID is the name of this network.
If you want to associate to an existing Ad Hoc network, enter the SSID of this network in the corresponding field and click the “Apply” button on the Configuration tab to make the setting take effect.
If you want to create a new Wireless Ad Hoc network, enter an unused SSID to identify your own network. Then click the “Apply” button to make the setting take effect.
Configuration of the Channel
To be part of a same network, wireless clients must use the same channel If you want to associate to an existing Ad Hoc network Channel in the main screen of the WLAN utility. Then click the “Apply” button to make the setting take effect.
If you want to create a new Wireless Ad Hoc network “Apply” button to make the setting take effect and “OK”.
, select the channel of this network in the corresponding field AdHoc
, select an unused channel, then click the
10
Page 11
Configuration of WEP encryption
The configuration of WEP encryption in Ad Hoc mode is similar to the one in Infrastructure Mode. Please refer to the above explanations.
The configuration of your Wireless LAN adapter in Ad-Hoc mode is finished.
About Status Information on your Wireless LAN USB
adapter LED Indicator
The SAGEM Wi-Fi 11g USB ADAPTER has a PWR LED and a DATA LED indicator giving the following informations on the link status:
PWR LED ON The adapter is receiving power from the USB port. OFF The adapter is not receiving power from the USB port.
The adapter may be disconnected or the computer is OFF.
LED DATA Blinking The adapter is transmitting or receiving data packets.
OFF There is no wireless data activity.
I. On the WLAN utility under Windows :
Icon of the WLAN utility
Icons link status description :
: excellent radio link
: radio link usable but weak
: not connected
11
Page 12
Status field on the Configuration Menu of the WLAN utility
The Status field on the Configuration menu provides more detailed information.
State : When operating in Infrastructure mode, this field shows the MAC address of
the Access Point with which the SAGEM Wi-Fi 11g USB ADAPTER is communicating. When operating in Ad-Hoc mode, it shows the virtual MAC address used by computers participating in the Ad-Hoc network.
Current Channel : Shows the radio channel on which the connection is made.
Current Data Rate : Shows the highest transmit rate of the current 54 Mbps to 1 Mbps.
Throughput : Shows the short term transmit and receive throughput in bytes/second, and is
continuously updated.
Link Quality : Based on the quality of the received signal
Signal Strength : Based on the received radio signal strength.
Uninstall the Wireless LAN adapter
I. Uninstallation :
1. To remove the Wireless LAN Utility from your computer, go to the Start menu and select
Sagem Utility / WLAN Card / WLAN Uninstall Sagem WLAN Card Utilities”.
2. Follow the instructions on the different screens to uninstall the Wireless Utility then click “Finish”.
3. Now you can disconnect your SAGEM Wi-Fi 11g USB ADAPTER.
Troubleshooting
If you experience any difficulty resolving the problem while installing or using the SAGEM Wi-Fi
11g USB ADAPTER, please contact the supplier for support.
12
Page 13
Problem Solution
At SAGEM Wi-Fi 11g USB ADAPTER installation, Windows was unable to locate the driver for this device.
The Wireless LAN adapter LED does not come on.
The Wireless LAN adapter LED flashes and you cannot access to your Access Point or to the other client stations of your network.
After a restart of your computer, the system cannot detected the Wireless LAN adapter plug into it.
Restart your PC and follow the screens showed up.
Check that the Wireless LAN adapter is correctly
connected.
Plug out the Wireless LAN adapter, then plug in it into the same USB port on your computer.
Under Windows check the Wireless LAN adapter driver is correctly installed. If this is not the case uninstall then reinstall the driver.
Check that the SSID and the WEP encryption keys are the same on the computers and the access point which are on the same network.
Check that the wireless network is operational.
Plug out the Wireless LAN adapter, then plug in it into the
same USB port on your computer.
All rights reserved Copyright 2005 SAGEM SA PARIS France
Ed. 01 Ref. 252122182
13
Loading...