Sage the Control Grip All In One Instruction Book

the Control Grip All In One

Instruction Book - BSB530UK

™

IMPORTANT
SAFEGUARDS

At Sage™ by Heston
Blumenthal
safety conscious. We design
and manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.

‰

we are very

SAGE
RECOMMENDS
SAFETY FIRST

READ ALL INSTRUCTIONS
BEFORE USE AND SAVE
FOR FUTURE REFERENCE

• Before using for the first
time please ensure that your
electricity supply is the same
as shown on the rating label on
the underside of the appliance.
If you have any concerns please
contact your local electricity
company.

• Your Sage™ by Heston
Blumenthal
includes a BS 13 amp moulded
mains plug on the supply cord.

‰

appliance

• Should you need to change
this plug, please complete the
rewiring as follows (after safe
disposal of the moulded plug).

• Please note that a cut off plug
inserted into a socket is a
serious danger risk.

• Wires are coloured as follows:

−Blue = Neutral

−Brown = Live

• As the colours of the wire
may not correspond with the
coloured markings which
identify the terminals in
your plug, please refer to the
following:

−The Blue wire must be
connected to the terminal
which is marked ‘N’.

−The Brown wire must be
connected to the terminal
which is marked with the
letter ‘L’.

• Please note that if a 13 amp
plug is used, a 13 amp fuse
should be used.

• Remove any packaging
material and promotional
stickers before using the stick
mixer for the first time.

• Do not place the stick mixer
near the edge of a bench or
table during operation. Ensure
the surface is level, clean and
free of water, flour, etc.

2

• Do not place the stick mixer
on or near a hot gas or electric
burner, or where it could touch
a heated oven.

• If using the stick mixer to
blend hot food in a saucepan
over heat, remove the saucepan
from the heat source and
ensure the power cord and
body of appliance are also kept
away from any heat source.

• Take care when handling the
stick mixer, attachments and
sharp cutting blades, when
emptying the bowl and during
cleaning. Remember the blade
and attachments are very sharp
and should be kept out of the
reach of children.

• Always make sure the stick
mixer is completely and
properly assembled
before operating.

• Ensure the stick mixer is
turned off at the trigger switch,
the power is switched off at
the power outlet and the cord
is unplugged from the power
outlet before attempting to
attach any of the accessories.

• Do not use attachments other
than those provided with the
stick mixer.

• Only use the whisk attachment
for the recipes contained in this
instruction booklet.

• Do not use the whisk
attachment for anything other
than its intended use.

• Do not attempt to operate the
stick mixer by any method
other than those described in
this booklet.

• Do not process hot or boiling
liquids in food processor bowl ­allow liquids to cool before
placing into the food processor
bowl.

• Do not operate the appliance
continuously for more than
1 minute. Allow the motor to
rest for 1 minute between
each use.

• Never mix dry, thick or heavy
mixtures for more than
30 seconds. Stop the operation
and stir the ingredients before
continuing. Allow the motor
to rest for 1 minute between
each use.

• When using heavy loads,
the appliance should not
be operated for more than
30 seconds.

• Always ensure the stick mixer
is turned off, the power is
switched off at the power outlet
and the cord is unplugged
from the power outlet before
attempting to move the
appliance, when not in use,
if left unattended and before
disassembling, cleaning or
storing.

3

• If food becomes lodged around
the processing blade or in the
blade guard, release the ON
button, switch the power off at
the power outlet and unplug
the cord. Use a spatula to
dislodge the food. Do not use
fingers as the blades are sharp.

• Do not remove the stick mixer
from ingredients during
operation. Ensure the appliance
is switched off and has stopped
turning before removing, to
avoid contact with moving
blade or whisk.

• CAUTION: In order to avoid
a hazard due to inadvertent
resetting of the thermalcut-out,
this appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and off by the utility.

• Do not leave the stick mixer
unattended when in use.

• To protect against electric
shock do not immerse the
motor body, cord or power plug
in water or any other liquid.

• Keep the appliance clean.
Follow the cleaning
instructions provided in
this book.

• Do not use the stick mixer/
stick blender with wet hands.

• Do not push food into the food
chute with your fingers or other
utensils. Always use the food
pusher provided.

• Keep fingers, hands, knives
and other utensils away from
moving blade and discs.

• Do not place hands or fingers
in the processing bowl of the
food processor unless the
motor, processing blade, dough
blade or disc has come to a
complete stop. Ensure the OFF
button has been pressed to
switch the motor off and the
appliance is switched off at the
power outlet and the power
cord is unplugged before
removing the lid from the
processing bowl.

IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES

• Unwind the cord fully
before use.

• Do not let the cord hang over
the edge of a table or counter,
touch hot surfaces or become
knotted.

• Keep the appliance and its cord
out of reach of children.

4

• Young children should be
supervised to ensure that they
do not play with the appliance.

• Do not use the appliance if
power cord, power plug or
appliance becomes damaged
in any way. If damaged or
maintenance other than
cleaning is required, please
contact Sage
Blumenthal
on 0808 178 1650 |

0333 0142 970 or go to
sageappliances.co.uk.

• This appliance is for household
use only. Do not use this
appliance for anything other
than its intended use. Do not
use in moving vehicles or
boats.
Do not use outdoors. Do not
use outdoors. Misuse may
cause injury.

• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current
not exceeding 30mA be
installed in the electrical circuit
supplying the appliance. See
your electrician for professional
advice.

™ by Heston

‰

Customer Service

• This appliance can be used by
persons with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe way
and understand the hazards
involved.

• This appliance shall not be
used by children. Keep the
appliance and its cord out of
the reach of children.

The symbol shown
indicates that this
appliance should not be

disposed of in normal
household waste. It should be
taken to a local authority
waste collection center
designated for this purpose or
to a dealer providing this
service. For more information,
please contact your local
council office.

SAVE THESE
INSTRUCTIONS

5

Components

A

B

K

L

M

N

A. Speed control dial
B. Easy grip trigger switch
C. Motor body
D. Processing gear box
E. Clear lid
F. 1.6L chopping bowl
G. Feed chute
H. Whisk
I. Stainless steel blending leg
J. Detachable mashing gear box
K. Detachable mashing leg

IJ H

L. Micro-serrated S-blade
M. Variable slicing disc
N. Reversible shredding disc
O. Storage base
P. Spindle

SAGE ASSIST™ PLUG

Your Sage appliance comes with a unique Sage
Assist
finger hole to easy removal from the wall outlet.

G

O

™ Plug, conveniently designed with a

P

™

C

D
E

F

6

Assembly

BEFORE FIRST USE

• Before using your mixer for the first time,
remove packaging material and promotional
labels. Do this while the POWER is off, and
the cord is unplugged.

• Be careful when handling the blending leg,
blades and discs as they are extremely sharp.

• Wash the blending leg, processing bowl,
processing lid and all attachments in warm
soapy water with a soft cloth. Rinse and dry
thoroughly.

ATTACHING THE MOTOR BODY

1. Hold the motor body over the blending leg,

masher, whisk, or gear box, as shown below.
Push together until it clicks and locks.

ASSEMBLING THE
PROCESSING BOWL

1. The spindle must be used with the S-blade,
adjustable slicer, and the fine and coarse
reversible shredder. Failing to use the
spindle will damage the parts, and
incorrect use this way may cause the
parts to fuse together.

2. Position the spindle over the coupling in
the centre of the processing bowl.

2. To release the motor body, squeeze the
EJECT buttons with thumb and finger as
shown below. Pull the motor body away,
while supporting the part you are releasing
it from.

3. Place either the S-blade, adjustable slicer,
or the fine and coarse shredder over the
spindle. Blades are extremely sharp ­position them by touching the plastic area
and keeping fingers away from blades

POSITIONING THE SHREDDER

7

POSITIONING THE ADJUSTABLE SLICER

POSITIONING THE S-BLADE

5. Position the gearbox as shown below, and
push down to click into place.

6. Add food through the chute, applying
gentle and even pressure with the pusher.
Do not use any other utensil to add or
push food.

4. Place lid onto the processing bowl so that
the ALIGN | LOCK graphics on the lid and
handle align. To LOCK the lid, hold the
chute and turn anti-clockwise.

8

ADJUSTABLE SLICER

The adjustable slicer has 18 precise settings.
To adjust the slicing thickness, hold the disc by
the edges with one hand, and turn the rotating
collar with the other hand. The numbers
printed on the collar are approximately the
thickness of the slice (in millimetres).

ASSEMBLING THE MASHER LEG

1. The masher leg is an assembly of 4 parts,
the gearbox, blade, outer leg, and inner leg.

2. Align the outer leg and gearbox as shown.

4. Rotate gearbox anti-clockwise while
holding the outer leg. Rotate until it clicks
and locks into place.

5. Refer to instructions in previous section to
attach the mashing leg with the motor body.
Push together until it clicks and locks.

6. Position blade on the underside of mashing
head, and lock by rotating anti-clockwise.

IMPORTANT

Blade will only attach when the mashing leg
is attached to the motor body.

7. Select the desired setting on the variable
mashing leg: textured, smooth or creamy.

3. Once aligned, hold the outer leg and
gearbox firmly with one hand. Insert the
inner leg and push up until it clicks and
locks into place.

9