Safeway EXECUTIVE Installation Instructions Manual

A: TOTHREAD SHOULDER STRAP

through loopof adjustorstrap

thread "free"end ofbelt through the firstslot ofthe 2-Slot slideronce again

B :TO THREADADJUSTOR BELT

1. Insert "free"end ofshoulder strap fromunderneath righthand side ofthe EXECUTIVE CARSAFETY SEATthrough slotin seat. Pull
through until 2-Slotslider touchesthe bottom ofthe seat.

2. Thread "free"end ofshoulder strap throughright handbuckle mechanism from underneathbuckle throughto top. Insertstrap
through desired right sideshoulder slot(according to heightof child'sshoulders)(Diagram 8)

3. Thread "free"end ofshoulder strap , thread throughleft handside shoulder slotfrom rearthrough to
front of seat. (Diagram9)

4. Thread throughleft sideof buckle mechanismfrom topto bottom, insert throughleft handside slot onbottom ofthe EXECUTIVE
CAR SAFETY SEAT (Diagram10).

5. Push beltunderneath bottomof chair betweenseat andreclining mechanism and threadthe beltthrough the 2-Slotslider (Diagram

11).

6. In orderto ensurethe belt issecure, (Diagram 12).

1. Adjust theEXECUTIVE CARSAFETY SEATto thesleeping position. Push theadjustor strap(small belt) betweenthe shelland the
base towards the frontof thechair. Threadthe adjustor beltthrough the2-Slot slider of thecrotch straptowards the topof the
EXECUTIVE CARSAFETY SEAT (Diagram13). Threadthe adjustorstrap through theadjustor buckleand pull through(Diagram

14).

Once you have selected the correct shoulder height and re-thread the belts, the belt can be adjusted by a simple adjustment of the
adjustor beltin front(Diagram 14). Pushthe "adjustor buckle"and pullthe harness totighten orpull on theharness to loosen.Youshould
be ableto comfortably fityour hand beneaththe harness foran ideal fitwith child strappedin the EXECUTIVECAR SAFETY SEAT.The
"adjustor buckle"holds theharness in afixed position.

Toremove the headrest, disengage the locking clip situatedat the back of the EXECUTIVE CARSAFETY SEAT, where the headrest
support legsslot intothe backrest (Diagram15). You cannow pull theheadrest out.

Tofit the headrest, simply slidethe headrest support legsinto the eyelets situated atthe top of theEXECUTIVE CAR SAFETY SEAT's
cover and into the holes in the backrest. Push the headrest down as far as possible. Replace the locking clip, making sure that it
engages.

All partsof theEXECUTIVE CAR SAFETYSEATcan be cleanedwith mildcleaning agents.

Should youwish toremove the cover, theharness can beremoved asfollows :

1. Unbuckle theharness andseparate the shoulderbelt fromthe 2-Slot sliderat the bottomof the EXECUTIVECAR SAFETYSEAT.

2. Slide theentire strapfree.

3. Remove cover.

4. The covercan bewashed in lukewarm waterwith a milddetergent. Do nottumble dry oruse anysolvents.

To replacethe harnesson the EXECUTIVECAR SAFETYSEAT referto .

1. The safetyof theEXECUTIVE CAR SAFETYSEATis only validIf instructions arecarefully followed. Keepinstructions wherethey
can be readilyfound.

2. Ensure thatthe EXECUTIVECAR SAFETY SEAT BELTS andthe vehicle safetybelts are inoptimum conditionbefore use. Ensure
that all beltsare tightlyfastened.

3. Ensure thatthe EXECUTIVECAR SAFETY SEAT isfastened inthe vehicle even whennot inuse.

4. Never leavea childunattended in theEXECUTIVE CARSAFETY SEAT.

5. Do notuse theEXECUTIVE CAR SAFETYSEATif it haspreviously been involvedin a collision.

6. Never leaveheavy objectson the rearparcel shelf,they could injure yourchild ifyou brake sharply.

7. Ensure thatyour childdoes not accidentallyunfasten thesafety belt while playing.

8. Do notuse theEXECUTIVE CAR SAFETYSEATfor children weighing morethan 18kg.

9. The seatcover orbelts should notbe replacedwith any otherthan the onerecommended by themanufacturer asthey constitute an
integral part ofthe restraints'performance.

10. Donot usethe EXECUTIVE CARSAFETY SEAT witha 2-Point safety belt.

11. TheEXECUTIVE CARSAFETY SEATwhen usedas a GROUP0 “rearwardfacing" must notbe usedin the frontpassenger seat
where the vehicleis equippedwith a passengerseat airbag.

12. Ensurethat ifthe EXECUTIVE CARSAFETY SEAT hasbeen exposed to directsunlight, nopart of ithas becomeexcessively hot.

13. Thebuckle hasbeen purposely designedto providea quick release.In the eventof an emergency, itmay benecessary for aperson
unfamiliar with theequipment torelease the childin seconds.The buckle has beendesigned therefore,so that evena childcan
undo it.This means thebuckle is nottamper proof.The childtransported in thesafety seat shouldbe disciplined tonot playwith the
buckle whilethe harnessis in use.

14. Ensurethat theEXECUTIVE CAR SAFETYSEATdoes not become trappedby amoveable car seator inthe door ofthe car.

15.

16. Donot hesitateto contact usif youhave any querieson yourEXECUTIVE CAR SAFETYSEAT.

Distributed by:Unimark Distributors(Pty) Ltd., P.O.Box 912-1095, Silverton,0127
Tel: [phone], Fax: [phone], E-mail: [e-mail]

HOW TOREMOVE ANDFIT THE HEADREST

HOW TOCLEAN THEEXECUTIVE CAR SAFETYSEATAND COVER

HOW TOADJUST HARNESSAND THREADBELTS

IMPORTANTPOINTS TOREMEMBER

SETTHE RIGHT EXAMPLE, ALWAYS BUCKLEUP.

EXECUTIVE

CAR SAFETY SEAT

EXECUTIVE

INSTALLATION INSTRUCTIONS

Group 0 : 0 - 10 kg
Group 1 : 10 - 18 kg

Please readthese instructions beforeuse. The EXECUTIVECAR SAFETY SEAT is suitablefor children frombirth to 18kg, newborn to
approximately 5years.

GROUP 0 0 -10 kg
GROUP 1 10 -18 kg

When used as a Group 0 safetyseat, i.e. when your infants mass is under 10 kg, the EXECUTIVE CARSAFETY SEAT can be used
either in the front or rear of the vehicle using a 3-POINT SEAT BELT. Please note that if the
vehicle isequipped witha PASSENGERSEAT AIRBAG, theEXECUTIVE CAR SAFETYSEATmust only beused in therear seats.The
EXECUTIVE CARSAFETY SEATmust not be fittedin the middle ofthe rear seatif it is onlyequipped with a 2-POINTSEAT BELT (Lap
belt).

1. Adjust the EXECUTIVE CAR SAFETY SEAT to the sleeping position (See "How to adjust reclining positions" (Diagram 5)). The
EXECUTIVE CARSAFETY SEAT shouldbe fully reclinedto ensure appropriatesupport. It isnot necessaryto install theheadrest
when in thisposition.

2. Fasten theseat beltin the seatwhere theEXECUTIVE CAR SAFETYSEATwill be used.

3. Place theEXECUTIVE CARSAFETY SEATin arearward facing position.

4. Lift thelap partof the belt(horizontal belt)through the gapson thebase. Slip thelap partof the belton eachside over theprotruding
base (Diagram1).

5. Pull thediagonal strapof the safetybelt asfar out asis neededto place itbehind theEXECUTIVE CAR SAFETYSEAT'sbackrest.
The strapmust befitted into thebelt guidebracket mounted inthe middle,on the back,at therear of theEXECUTIVE CARSAFETY
SEAT. (Diagrams1 &2)

6. YourEXECUTIVE CARSAFETY SEATis nowsecured. Totighten theseat belt asmuch aspossible, push theEXECUTIVE CAR
SAFETY SEATdown intothe vehicle seat.Adjust thevehicle seatbelt accordingly.Make sure thatthe beltis adjusted tightly. Itis
quite normal forthe safetybelt of thevehicle tohave some playafter tensioning.

When the child'smass exceeds 10 kg,it may now be transportedfacing forward. In thisposition the EXECUTIVE CAR SAFETYSEAT
should be placedon the rear seat of thevehicle. The EXECUTIVE CAR SAFETYSEAT can only beused with a 3-Point seat belt.The
EXECUTIVE CARSAFETY SEAT mustnot be fittedin themiddle of therear seatif it isonly equippedwith a 2-Pointseat belt(Lap belt).

1. Fasten theseat beltin the seatwhere theEXECUTIVE CAR SAFETY SEAT willbe used.

2. Place theEXECUTIVE CARSAFETY SEATon therear seat ofthe vehicle ina forward facingposition.

3. Lift thelap partof the belt(horizontal belt)through the gapsin thebase.Slip the lappart ofthe belt oneach sideover the protruding
base. (Diagram 3)

4. Pull thediagonal strapof the safetybelt asfar out asis neededto place itbehind theEXECUTIVE CAR SAFETYSEAT'sbackrest.
The strap mustbe fittedinto the beltguide bracketmounted in themiddle, onthe back, atthe rearof the EXECUTIVECAR SAFETY
SEAT. (Diagram 2)

5. YourEXECUTIVE CARSAFETY SEATis nowsecured. Totighten theseat belt asmuch aspossible, push theEXECUTIVE CAR
SAFETY SEATdown intothe vehicle seat.Adjust thevehicle seatbelt accordingly.Make sure thatthe beltis adjusted tightly. Itis
quite normal forthe safetybelt of thevehicle tohave some playafter tensioning.

Once the EXECUTIVE SAFETY SEAT is fastened in the vehicle with the safety belt,pull the safety belt as tight as possible and then
place and fasten the RED SAFETY CLIP on the shoulder belt strap directly above the buckle to ensure stability of the EXECUTIVE
SAFETY SEAT. (Diagram 4)

The EXECUTIVE CAR SAFETY SEAT features 5 different reclining positions, from seated to fully reclined. The EXECUTIVE CAR
SAFETY SEAT's position can be changed by simply pulling the red lever in the centre underneath the seat and adjusting the
EXECUTIVE CARSAFETY SEAT upor down. Byreleasing thelever, theseat locks automaticallyin thedesired position (Diagram5).

1. Interlock thebuckle partsattached to theshoulder strapsso that they formone unit(Diagram 6).

2. Fit bothparts intothe buckle housingwhich isattached to thecrotch strap (Diagram7).

3. Press untilengagement " " isheard, andensure all partsare secured.

4. Torelease thebuckle press theRED RELEASEBUTTON on the buckle.

In orderto change theshoulder height adjustment,select the slotsin the EXECUTIVECAR SAFETY SEAT whichare the correctheight
just aboveyour child's shoulders.If a changeof height is necessary, unfastenthe harness andseparate the beltsfrom the EXECUTIVE
CAR SAFETYSEAT.

INSTALLATION INSTRUCTIONS- GROUP 0(0 -10 kg "REARWARDFACING")

INSTALLATION INSTRUCTIONS- GROUP 1(10 -18 kg "FORWARDFACING")

ATTACHING THERED SAFETY CLIP

HOW TOADJUST RECLININGPOSITIONS

HOW TOUSE THEEXECUTIVE CAR SAFETYSEATBUCKLE

HOW TOADJUST THEHARNESS ANDTHREAD BELTS

BUT MUST BE REARWARD FACING

(ONLYPLACE THECLIP OVERTHE SHOULDER BELTAND NOT THELAP BELT)

CLICK

ONLY TO BE USED WITH A 3-POINT SEAT BELT

SAFEWAY EXECUTIVE CAR SAFETY SEAT INSTALLATION INSTRUCTIONS

12

3

4

56

7

89

10

11 12

14

15

13