Safetymind Wireless 8839 433 Users manual

8839-433 SERIES

Wireless Key Transmitter

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The 8839-433 key transmitters are portable wireless transmitters for use onl y with wireless alarm systems that sup port DSC wireless receivers

(ex. DSC hardwired panel s, 9047, & 9057). The 88 39-4 33 i s re plac emen t remote of DSC W S4939

 B utt ons are typically used for ar ming a nd d isarmi ng, but ca n b e programmed for any appropriate zo ne respo nse.

 A but ton must be pres sed and held unt il the LED be gins to flash to activate a button function. This press and hold feature

minimizes the possibility of a ccidental transmissions.

The fac tor y-i nstall ed repl ace abl e lithi um batt ery pr ovi des pow er for up to five (5) years.

Button Features

Buttom 1: Stay Arming

Press this button to arm your system in the Stay mode. All perimeter zones will be armed, such as all window and
door contacts,but the interior zones will remain inactive, allowing you to stay on the premises without setting off
an alarm.

Buttom 2: Away Arming

Press this button to arm your system in the Away mode. Both the interior and exterior zones
will be armed, allowing you to exit the premises.
Buttom 3: Disarm

Press this button to disarm your system. You do not have to enter your access code when
you use the key to disarm the system.
Buttom 4: Panic

Press this button to notify your central monitoring station of a situation requiring the police,
such as a break-in.

PROGRAMMING

For com plet e de tails on how to prog ram the transmitter at the control panel, see the co ntrol uni t's Install atio n Instruction s. W hen

programming , note the foll owing:

 Each 8839-433 transmitter has one unique serial numbers assigned during manufacture.

Programmi ng for 9057 panels:

＊8 - 5555 - 898 / Learn sensor / Press any key on the remote / Once learned, press

Then you w ill see Key 1(If the remote is the 2nd remote, you need to
Then press * * then ## to get out of programming.
Need to set up following if the remote still not recognized : 015 – 12345 / 016 – 2568

REPLACING THE BATTERY

The LED will not flas h during battery as follows.

1. Remov e the ca se back.

2. Ins ert t he blade of a sm al l s crewdriver under batt ery as s hown to open the case .

3. With the Positive (+) end of a new battery facing Up & insert the battery as shown, t hen pres sing
do wn to sn ap i nto place.

IMPORTANT:

Positive (+) end must face up. Use Maxell CR2032, Duracell DL2032

• Im pro per installat ion wi ll res ult in damage

• Do n ot remove the prin ted circuit boar d.

SPECIFICATIONS

Unit D imensi ons: 2.36" x 1.1 2" x 0.41" (60 mm x 28.6mm x 1 0.5m m)

Federal Communications Commission Statement

This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures:
Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate this equipment.