Safety 1st Store ‘n Go Sport User Manual
To see installation videos, scan the QR Code
or visit www.safety1st.com
©2017 Dorel Juvenile.
Store ‘n Go Sport
2-in-1 Booster
40-110 lb (18.1-49.9 kg)
43-57 in. (110.1-144.8 cm)
KEEP INSTRUCTIONS FOR FUTURE USE.
Read all instructions before using
this booster seat.
4358-7323
7.10.17
Failure to follow the warnings on the labels and
in the instruction manual can result in serious
injury or death to your child.
Table of Contents
Getting Started............................1
Parts of the Booster Seat ..............................1
General Use ..................................3
Preparing Seat .............................................3
Installing Seat Pad ..................................3
Attaching Headrest to Backrest ................5
Attaching Backrest to Base .....................5
Adjusting Backrest .................................6
Adjusting Headrest .................................6
Removing Backrest .................................7
Storage Drawer ......................................8
Removing Seat Pad for Cleaning ..............9
Safety Information ......................11
Booster Seat Use ..........................................11
Installation in Vehicle ....................................12
Vehicle Seating Position ................................ 12
Vehicle Information ....................14
Understanding Your Vehicle ...........................14
Knowing Your Vehicle Belts ............................15
Aircraft Information ......................................16
Booster Seat with Backrest ...... 17
Lap and Shoulder Belt Installation ...........18
Booster Seat without Backrest ..20
Lap and Shoulder Belt Installation ...........21
Important Information ............... 23
Dorel Juvenile Group Information... ................23
Registration and Safety Notices .....................24
Troubleshooting... .........................................25
Replacement Parts Order Form ......................26
Warranty ......................................................28
© 2017 Dorel Juvenile
12
Front View
A. Headrest
B. Shoulder Belt-
Positioning Guide
C. Backrest
D. Armrest
E. Seat Base
F. Storage Drawer
G. Storage Drawer Lock
H. Cup Holder
I. Plastic Snap Strip
For Seat Base Pad
A
B
C
D
H
E
F
Back View
A
B
C
E
H
J
L
J. Headrest Adjustment Lock
K. Instruction Manual
Storage (under seat bottom)
L. Backrest Lock
(under the seat bottom)
G
K
I.
Parts of the Booster Seat
34
4. Attach Headrest Pad
Slide the headrest pad over
one side of the headrest, then
the other.
From the back of the
headrest, attach the elastic
straps to the hooks at the top
and bottom.
5. Attach Backrest Pad
Slide backrest pad onto one
side of the backrest. Pull
pad tight and slide the pad
over the other side of the
backrest.
Bottom of the headrest
pad should be behind the
backrest pad as shown.
WARNINGS: Do not use this booster seat
without the seat pad. Failure to do this can result
in serious injury.
2. Attach Seat Base Pad
Push in the locking tabs into
the holes on the front of the
seat base.
Preparing Seat
1. Insert Plastic Snap Strip
into Front of Seat Pad
Push locking tabs in the
holes on the front of the
seat base pad, as shown.
Note: Depending on your model, you may need to
prepare the seat for use.
Installing Seat Pad
3. Fasten Elastic Straps to
Bottom of Seat Base
From bottom of seat base,
fasten elastic straps.
56
Note: Headrest MUST always be used when using backrest.
If headrest has been removed from backrest.
1. Find Backrest
Connection Slot
Lift flap on seat pad as
shown to reveal backrest
connection slot.
2. Attach Backrest to
Seat Base
Insert the hook on the
backrest into the backrest
connection slot.
Make sure backrest is laying flat (horizontal) when
connecting.
3. Rotate Backrest Up Until It
Clicks into Place
Tuck seat pad flap under
backrest flap.
Attaching Backrest to Base
1. Rotate Backrest Forward
or Back to Desired Position
The backrest should be flush
with vehicle seat back angle.
NOTE: The backrest and headrest are removable. The
headrest and backrest must always be used together.
To use as a backed booster, attach headrest to backrest
and backrest to seat base, as follows.
With the back of the headrest
and backrest facing up, slide the
headrest into the track on the
back of the backrest.
Pull headrest adjuster lock out
and pull headrest down into a
locked position.
Attaching Headrest to Backrest
NOTE: Make sure seat pad does not get caught between
the moving parts. The backrest may not connect properly
if the pad is in the way.
Adjusting Backrest
1. Raise or Lower Headrest to
Selected Position
This booster seat has multiple
headrest positions. Grasp top of
headrest and push down with
one hand while pulling out on
the headrest adjustment lock
with the other.
Raise and lower headrest into
selected position. Release
the headrest adjustment lock
into one of the many headrest
heights.
Make sure headrest is locked by sliding headrest up and
down. Headrest may move slightly when it is locked.
Adjusting Headrest
Loading...