Safety 1st 015611, BO069, Clean & Comfy User Manual

Clean & Comfy Booster Seat

015611 / BO069 User Guide

Age: 6 months to 4 years.
Maximum weight: 20 kg.
Adult assembly required.

•

Remove all contents from packaging and discard box and/or poly bags.

Have ready the model number (015611) and date code
(manufacture date) located on underside of the booster seat base.

• Lay out and identify all parts.

• Do not return this product to the place of purchase. If any parts are
missing, please contact our Customer Service Team:

•

Before Assembly: Wipe down trays with a soft cloth and warm soapy

water.

WARNING:

• Prevent serious injury or death from sliding out, falls, or
tipping over.

• ALWAYS secure child in the restraint until child is able
to get in and out of the booster seat without help (about
2-1/2 years old). The tray, if supplied, is not designed to
hold the child in the chair.

• NEVER leave child unattended.

• NEVER allow a child to push away from table.

• ALWAYS fasten seat and back straps securely to adult chair.

• ALWAYS check security of t to adult chair before each use.

• This booster seat is only to be used with standard kitchen

or dining room chairs. NEVER use this product as a car seat
or bath seat, on a tabletop, stool, swivel chair, or any other
seating surface where the straps cannot secure it properly.

• Prevent serious injury or death. NEVER use in motor vehicles.

• ALWAYS ensure that all chair protector pads are located

completely on the adult chair surface.

• Discontinue use if damaged, broken or if parts are
missing.

• Keep small parts away from children during assembly.

CAUTION:

© 2014 Dorel Australia Pty Ltd. All Rights Reserved.

Made in CHINA AX: 015611 09/14

safety1st.com.au

Australia

Parts List

A
B
C

F

D

G

E

H

I

J

To Assemble

Insert tray
Tray
Seat
Waist restraint
Seat attachment hooks & snaps

Base
Adult chair topper
Protector pad (3)
Chair straps (2 sets)
Tray release

1 Preassembled Parts

C D F H

:

Three protector pads (Figure 1a) and
child waist restraint (Figure 1b) will
come preassembled to base and seat,
respectively.

1a 1b

Waist restraint

D

J

E

A

B

C

F

G

I

H

F

1

Dorel Australia Pty Ltd

655-685 Somerville Road
Sunshine West, Victoria, 3020
Melbourne: [phone]
Australia wide (local call cost): 1300 809 526
Hours: 8:30 am - 5:00 pm, Monday to Friday
Email: [e-mail]

IGC Dorel New Zealand Ltd

14 Sir William Avenue
East Tamaki, Auckland, 2013
Auckland: [phone]
NZ wide (toll free): 0800 628 000
Hours: 8:00 am - 5:00 pm, Monday to Friday
Email: [e-mail]

2

G

I

H

2

Attach Seat

C EC F

:

Place seat face-down on flat surface with hooks and snaps
facing upward (Figure 2a). Align base and seat as shown
(Figure 2b). Turn seat so that underside of the base faces
towards you. Insert hooks on the seat into the corresponding
slots on the base (Figure 2c). Ensure hooks are inserted
correctly; locking tabs should slide beneath them (Figure 2d).

To Assemble

(continued)

3 Secure Seat

E F

:

Place hands on seat base as seen below and firmly push base
until it is fully engaged with seat (Figure 3a). After seat clicks
into place, ensure that hooks and snaps are locked and secure
as seen below (Figure 3b).
Note: If seat is not secure, use force to push base onto seat to
ensure proper attachment.

3b3a

Snap

Hook

2b2a

Hook

Snap

2c 2d

4 Attach Chair Straps

(2 sets)

F I

:

Locate chair straps.
Snap buckles together
(Figure 4a).

With one set of straps,
insert folded ends into
two openings on back of
the base (Figure 4b).

With second set of
straps, insert folded
ends into two openings
on either side of the
base (Figure 4c).

Pull each strap to ensure
strap is secure.

4b

4a

4c