User Guide
Front Panel
1. Time Set Button 8. Test Switch
2. Alarm Set Button 9. Vibrating Pad Port
3. Snooze Button 10. Volume Switch
4. Hour Adjust Button 11. USB Port
5. Minutes Adjust Button 12. Audio Tone Switch
6. Alarm Switch 13. Power Cable Port
7. Display Dimmer Switch 14. LED Side Light Switch
Back Panel
Instructions:
Insert the Vibrating Pad jack into the Vibrating Pad Port
(9) and insert the power supply jack into Power Cable
Port (13). Insert the power supply plug into a socket and
switch on.
If keeping the clock by your bed we recommend the
vibrating pad is placed under a pillow.
To set time:
Press and hold the Time button (1), followed by the
Hour button (4) to change the digit, press several times
until you reach the desired hour. Do the same for the
minutes by pressing the Minute button (5) together with
the Time button (1).
To set alarm:
Press and hold the Alarm button (2) followed by the
Hour (4) and Minutes (5) buttons to the desired time.
Set the alarm switch (6) to the on position.
How to turn off the alarm:
When the alarm goes off, press the Snooze button (3) to
snooze the alarm for approx. 9 minutes. You can
continue this process 7 times before the alarm mode
turns off. To switch the alarm off straight away, or stop
snooze mode, press and hold the Snooze button (3) for
3 seconds.
The set alarm will then repeat at the desired time the
next day.
Other functions
Test the Alarm
You can test the alarm mode by pressing the test button
(8) to release. When the button is protruding out the
test mode will activate. Push the button back in to turn
the test off.
Charge your Mobile Phone
Insert your mobile phone’s USB charger into the USB
port (11). Can be used to charge most 5V mobile phones
or other electronic devices.
Adjust the clock display and Alarm Sound
The brightness of the display can be adjusted by pressing
the display dimmer switch (7).
You can choose the desired volume of the alarm sound
by adjusting the volume switch (10) between HI, LO and
OFF. The tone of the alarm sound can also be adjusted
using the Audio Tone switch (12) between HI, MED and
LO.
The clock’s lights can be turned on/off using the LED side
light switch (14).
Power Cut
In the case of a power cut the clock will memorise the
time for up to 72 hours so no need to reset the time and
it ensures the alarm remains correct while you are
sleeping.
Disposal of old electrical and electronic equipment
This product may not be treated as household waste.
Instead it should be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment.
For more information about recycling this product, please
contact your local council office or household waste disposal
service.
Dispose of batteries in the correct manner via your local waste
recycling centre and not in your general waste bin.
Congratulations on purchasing your Shake ‘n’ Wake™
Extra Loud Alarm Clock from Safe and Sound Products.
This alarm clock’s vibrating pad, flashing lights and extra
loud sounder will help to wake even the heaviest sleeper.
It also has a jumbo display to help people with poor sight
and a USB socket to charge your mobile phone.
Contents
• Extra Loud Alarm Clock
• Vibrating Pad
• UK Mains Power Supply
• User Guide
Safety Information
Use only the power adaptor supplied.
Do not overload power outlets and extension cords. This
can result in fire or electric shock.
Completely insert the power adaptor into the power
outlet. Failure to do so may result in electric shock
and/or excessive heat causing a fire.
Regularly remove any dust etc. from the power adaptor
by pulling from the power outlet and wiping with a soft
dry cloth. Accumulated dust may cause an insulation
defect.
Unplug the product from power outlets if it emits smoke,
an abnormal smell or makes an unusual noise.
Unplug from power outlets and never touch the inside of
the product if the case is broken.
Never touch the plug with wet hands – danger of electric
shock exists.
Always ensure there is a free flow of air over the alarm
clock.
Cleaning
Unplug and clean the alarm clock and vibrating pad with a
soft cloth. Do not use polish or other cleaning agents as
they may damage the inside or finish of the product.
Operating Safeguards
Unplug the product from the power outlet before
cleaning. Do not use liquid or aerosol cleaners.
Do not disassemble the product.
Do not spill liquids (e.g. detergents, cleaners) onto the
product or plug, or allow them to become wet. This may
cause a fire.
Volume Warning
This unit has a maximum operating
volume of 95dB.
SS/10700 working temperature：0°C to 40°C
Guarantee
This product is guaranteed for 2 years from the time of
purchase. During this time all repairs and replacements
(at our discretion) are free of charge. The guarantee
excludes general wear and tear and damage to cables.
Important: Your receipt is part of your guarantee and
must be retained and produced in the event of a warranty
claim.
Shake ‘n’ Wake Extra Loud Alarm Clock
User Guide
Product Code: SS/10700
Made in China
www.safeandsoundproducts.net
Safe and Sound Products
c/o Gordon Ellis & Co.
Trent Lane, Castle Donington
Derby, DE74 2AT, UK
info@safeandsoundproducts.net
01332 856022
Loading...