Safco Plan Master Assembly Instructions Manual
Plan Master
Height Adjustable Drafting Table
an LDI Spaces Company
Minneapolis, MN 55428
www.safcoproducts.com
PRODUCT WARRANTY REGISTRATION is available online at: www.safcoproducts.com
Tools required: Phillips screwdriver, hammer
(nail or pointed tool may be used to help start holes)
LETTER
CODE
A
Left Frame Assembly 1 3957-51BL
B
Right Frame Assembly 1 3957-52BL
C
Back Panel 1 3957-53BL
D
Horizontal Tube 2 3957-54BL
E
Lift Bar 1 3957-55BL
F
Left Support Channel 1 3957-60BL
G
Right Support Channel 1 3957-61BL
S
DESCRIPTION
TABLE TOP (SOLD SEPARATELY)
T
READ THESE INSTRUCTIONS BEFORE STARTING! FOLLOW THE ASSEMBLY PROCEDURES CAREFULLY.
PART NO.
QTY.
ASSEMBLY INSTRUCTIONS
PARTS LIST
LETTER
CODE
H
I
J
K
L
M
N
DESCRIPTION
Tube Plug
Large Flat Head Machine Screw
Long Pan Head Machine Screw
Pan Head Hi-Grip Screw
Nylon Spacer
Washer
Adjustment Knob, Black
8 3957-76BL
18 3957-79NC
4 3957-82NC
2 3957-71NC
2 3957-73BL
PART NO.
QTY.
2 3957-77NC
16 3957-78NC
LETTER
CODE
O
*Table Tops below sold & shipped separately
Drawing Board – 60" 1 3948*
Drawing Board – 48" 1 3951*
Leveler
P
Drawing Board Support Bar
Q
Pencil Bar
R
Short Pan Head Machine Screw
S
T
3957
DESCRIPTION QTY.
4 3957-75NC
2 3957-65BL
1 3957-83BL
2 3957-74NC
PART NO.
F
D
J
E
I
C
J
N
Adjustment Knob AT-
TENTION!
Do NOT loosen
until instruction num-
ber 9.
Q
P
K
G
K
D
I
J
L
R
M
B
H
O
A
3957-37EN: 1 of 4;
Rev. 2; 02/06
ASSEMBLED
UNIT
For questions or concerns, please call the Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time) (English-speaking operators)
Locate the A Left Frame Assembly (the short chan-
1
nels will be on the right side of the frame), and the B
Right Frame Assembly (the short channels will be on
the left side of the frame).
A
SHORT CHANNELS
N
ATTENTION!
Do NOT
unscrew the
ADJUSTMENT
KNOBS
until the final
instruction.
Place the A Left Frame Assembly on a protected
2
surface with the short channels upward. Insert the
H Tube Plugs if they are not already installed on the
tube ends. Insert the O Levelers. Repeat with the B
B
Right Frame Assembly.
O
A
H
3
OF RIGHT
ASSEMBLY
UPPER
END
FRAME
D
UPPER
END
OF LEFT
FRAME
ASSEMBLY
SHORT
CHANNELS
Insert the D Horizontal Tubes onto each of the short
channels along the upper end of the Left Frame Assembly. Attach using two J Long Pan Head Machine
Screws for each tube. Insert one end of the C Back
B
J
C
J
A
Panel onto the two lower short channels and attach
using four J Long Pan Head Machine Screws.
With the help of an assistant, carefully lift the B Right
Frame Assembly up and insert the short channels into
the open ends of the tube and back panel. Loosely
fasten using eight J Long Pan Head Machine Screws.
Carefully turn the assembled base upright.
Place one L Nylon Spacer on the pin. Insert the G Support
4
Channel onto the pin. Place one L Nylon Spacer and one M
Washer on the pin and fasten securely using one R Short Pan
Head Machine Screw. Repeat for the other support channel
and frame.
3957-37EN: 2 of 4; Rev. 2; 02/06
G
Do Not
Overtighten.
L
M
R
Safco Products Company, New Hope, MN 55428
FRAME
HINGE
PIN
Loading...