Safco 1851 Assembly Instructions Manual

an LDI Company

New Hope, MN 55428

Visit us on the web:

www.safcoproducts.com

Mobile Machine Stand

ASAS

AS

ASAS

TOOLS REQUIRED: Short Handled Phillips Screwdriver; Hammer or Mallet (Two People Recommended)

SEMBLSEMBL

SEMBL

SEMBLSEMBL

Y Y

Y

Y Y

INSTRUCTIONSINSTRUCTIONS

INSTRUCTIONS

INSTRUCTIONSINSTRUCTIONS

1851

PRODUCT WARRANTY REGISTRATION is available online at: www.safcoproducts.com

E

D

A

Z

B

O

T

H

V

W

K

§ Note: When corresponding about parts, be sure to state color:
Gray (GR), Mahogany (MH) or Medium Oak (MO).

For questions or concerns, please call

L

O

ASSEMBLED UNIT

MODEL 1851

N

F

M

Q

P

Safco Consumer Hot Line 1-800-664-0042

available Monday-Friday 8:00 AM to 4:30 PM (Central Time)

(English-speaking operators)

J

X

G

O

I

C

Y

W

U

K

S

R

Sort and count your parts!

PARTS LIST

LETTER

CODE

Back Panel 1 1850-01§

A

Left Side Panel 1 1851-03§

B

Right Side Panel 1 1851-04§

C

Short Back Panel 1 1851-01§

D

Top Panel 1 1850-05§

E

Fixed Shelf 1 1851-06§

F

Tall Screw Post 16 HFFMFB

G

Tall Cam 16 HFFMFC

H

Short Screw Post 4 HMF12B

I

Short Cam 4 HMF12

J

Caster Bracket 4 1854-10

K

Machine Screw, 5/8”L 8 1850-22

L

Bottom Panel 1 1850-02§

M

Kick Panel 1 1850-07§

N

Wood Dowel 8 H8MMDWL

O

Swivel Caster with Brake 2 8917-24

P

Swivel Caster without Brake 2 8917-25

Q

Hinge 4 8919-16

R

Hinge Mount Plate 4 8919-14

S

Left Door Panel 1 1850-08§

T

Right Door Panel 1 1850-09§

U

Handle 2 8962-31

V

Long Screw, 1”L 4 1850-23

W

Divider 1 1851-07§

X

Shelf Peg 24 HSFBNZ

Y

Small Shelf 6 1851-08§

Z

DESCRIPTION QTY. PART NO.

V

1851-37: 1 of 4; Rev. 3; 09/06

Safco Products Company, New Hope, MN 55428

IMPORTANT

 READ and FOLLOW these instructions carefully!
 CHECK ALL PACKAGING - there may be parts in it!
 SORT and COUNT your parts - compare with the parts list on page 1.

Work on a smooth and clean surface. Arrange the A Back

1

Panel, B Left Side Panel and C Right Side Panel with the
holes facing up as shown.

Place the D Short Back Panel
above the A Back Panel with large
holes up and insert J Short Cams
in the Short Back Panel. Arrange
the F Fixed Shelf below the Back
Panel and insert H Tall Cams in the
large corner holes of the Back
Panel and Fixed Shelf.

Insert two H Tall Cams in the two
large holes at the upper end of the
side panels, and insert two I Short
Screw Posts in the holes at the
upper center of each side panel.
Screw six G Tall Screw Posts into the small
holes in the upper, lower and back edges
of each side panel as shown. Fasten two K Caster
Brackets to the bottom end (unfinished edge) of each side
panel using two L 5/8” Machine Screws each.

Place the E Top Panel above the Short Back Panel with the
six small holes upward; screw four G Tall Screw Posts into the
corner holes.

B

D

H

I

UNFINISHED

EDGES

E

L

K

G

J

A

Insert two O Wood Dowels into both ends of
the N Kick Panel and the X Divider.

O

X

I

H

C

H

K

N

O

L

F

Raise the A Back Panel so it is perpendicular to the

2

B Left Side Panel. Align the two Screw Posts at the
back end of the Side Panel with the corresponding
holes on the Back Panel. With the arrows on the
Cams pointing toward the Screw Posts, guide the
holes over the Screw Posts and fasten by turning
each of the engaged cams CLOCKWISE as far as
they can turn. Install the D Short Back Panel in a
similar manner.

IMPORTANT: to prevent possible damage during
assembly, a second person should help support the
back panel in its upright position (or prop upright
with appropriate materials).

D

B

Position the F Fixed Shelf with the Cord Cutout next

3

to the A Back Panel, and the side with cams toward
the bottom end of the side panel. Align the two
Screw Posts on the Left Side Panel with the corre­sponding holes on the edge of the Fixed Shelf. With
the arrows on the Cams pointing toward the Screw
Posts, insert the Screw Posts and fasten by turning
each of the engaged cams CLOCKWISE as far as
they can turn. Insert the screw posts on one end of
the M Bottom Panel into the holes on the bottom
end of the Left Side Panel and fasten the cams .

CORD
CUTOUT

F

A

A

M

1851-37: 2 of 4; Rev. 3; 09/06

Safco Products Company, New Hope, MN 55428

FRONT;

FINISHED EDGES

BOTTOM

END