Saeco Primea Touch Plus Cappuccino, SUP 030 ADR Operation And Maintenance Manual

TABLE OF CONTENTS

Operation and maintenance manual

Before using the machine, please read the attached operating instructions.

Carefully read the safety rules

FOR HOUSEHOLD USE ONLY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be
followed, including the following:

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to person do not immerse

cord, plugs, or machine in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near
children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.

6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair or
adjustment.

7. The use accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cords hang over edge of table or counter, or touch hot surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Always attach plug to appliance first, then plug cord into wall outlet. To

disconnect, turn any control to “off”, then remove plug from wall outlet.

12. Do not use appliance for than intended use.

13. Save this instructions.

SAVE THESE INSTRUCTIONS

CAUTION

This appliance is for household use only. Any servicing, other than cleaning and
user maintenance, should be performed by an authorized service centre. Do
not immerse machine in water. To reduce the risk of fire or electric shock, do not
disassemble the machine. There are no parts inside the machine serviceable
by the user. Repair should be done by authorized service personnel only.
1 Check voltage to be sure that the voltage indicated on the nameplate

corresponds with your voltage.

2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during

operation.

4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft

cloth dampened with water.

5 For optimal taste of your coffee, use purified or bottled water. Periodic

descaling is still recommended every 2-3 months.

6 Do not use caramelized coffee

INSTRUCTIONS FOR THE POWER

SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be

provided to reduce risks resulting from becoming entangled in or tripping
over a longer cord.

B. Longer detachable power-supply cords or extension cords are available and

may used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,

1. The marker electrical rating of the detachable power-supply cord or

extension cord should be at least as great as the electrical rating of the
appliance

2. If the appliance is of the grounded type, the extension cord should be a

grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the counter

top or table top where it can be pulled on by children or tripped over.

2

GENERAL INFORMATION .................................................................................................................................3

MAC HINE ........................................................................................................................................................4

ACCESSORIES ....................................................................................................................................................................4

INS TALL ATION ................................................................................................................................................5

STARTING THE MACHINE ........................................................................................................................................................5

MANUAL PRIMING OF THE WATER CIRCUIT ....................................................................................................................................6

SETTING THE LANGUAGE AND THE CLOCK ....................................................................................................................................6

INTENZA WATER FILTER .........................................................................................................................................................7

DISPLAY .........................................................................................................................................................8

CHOOSE COFFEE AROMA ........................................................................................................................................................8

ADJ US TME NTS ...............................................................................................................................................9

COFFEE INTENSITIY ..............................................................................................................................................................9

ADJUSTING THE HEIGHT OF THE DRIP TRAY. .................................................................................................................................9

FILLING THE MILK CONTAINER..................................................................................................................................................9

BEVERAGE DISPENSING ................................................................................................................................10

ESPRESSO / COFFEE / LONG COFFEE .......................................................................................................................................10

DISPENSING BEVERAGES WITH GROUND COFFEE ........................................................................................................................... 11

HOT WATER DISPENSING ...................................................................................................................................................... 12

LATTE MACCHIATO .............................................................................................................................................................12

ESPRESSO MACCHIATO ........................................................................................................................................................14

CAPPUCCINO ...................................................................................................................................................................14

DISPENSING HOT MILK ........................................................................................................................................................15

BEVERAGE PROGRAMMING .......................................................................................................................... 15

BEVERAGE PROGRAMMING MENU ............................................................................................................................................15

ESPRESSO / COFFEE / LONG COFFEE PROGRAM ........................................................................................................................... 15

PROGRAMMING MILK BEVERAGES ............................................................................................................................................16

PROGRAMMING THE MACHINE .....................................................................................................................18

MACHINE SETTINGS ...........................................................................................................................................................18

LANGUAGE MENU ............................................................................................................................................................. 19

CUP ILLUMINATION MENU .................................................................................................................................................... 19

WATER FILTER MENU ......................................................................................................................................................... 19

WATER HARDNESS MENU - INTENZA AROMA SYSTEM ................................................................................................................... 20

RINSE MENU ................................................................................................................................................................... 20

CUP WARMING PLATE MENU ................................................................................................................................................. 21

ACCOUSTIC TONES AND ALARMS MENU .................................................................................................................................... 21

DISPLAY MENU ................................................................................................................................................................ 21

BEVERAGE SET TINGS ..........................................................................................................................................................22

ADJUSTMENT OF THE COFFEE BREW TEMPERATURE ..................................................................................................................... 22

AROMA ADJUSTMENT FOR COFFEE BREWING.............................................................................................................................. 23

PREBREWING ADJUSTMENT (ONLY COFFEE BEVERAGES) ................................................................................................................ 23

ADDITIONAL FUNCTIONS ......................................................................................................................................................24

COFFEE OF THE WORLD FUNCTION ......................................................................................................................................... 24

DEMO MODE ................................................................................................................................................................... 26

BEVERAGE COUNTER FUNCTION ............................................................................................................................................. 26

MAINTENANCE..................................................................................................................................................................27

MILK CIRCUIT RINSE CYCLE ..................................................................................................................................................27

MILK CIRCUIT WASH CYCLE .................................................................................................................................................. 28

COFFEE CIRCUIT CLEANING CYCLE (BREW GROUP WASH CYCLE) ....................................................................................................... 31

BLOCK DISPLAY .............................................................................................................................................................. 31

DESCALING .................................................................................................................................................................... 32

CLOCK SETTINGS ..............................................................................................................................................................34

TIME SETTING ................................................................................................................................................................. 34

AUTOMATIC TIMER SETTINGS ................................................................................................................................................ 35

ENERGY SAVING SETTINGS ................................................................................................................................................... 37

SPECIAL .........................................................................................................................................................................38

FACTORY SET TINGS ........................................................................................................................................................... 38

CLEANING AND MAINTENANCE .....................................................................................................................39

MAINTENANCE DURING OPERATION ..........................................................................................................................................39

GENERAL MACHINE CLEANING ................................................................................................................................................39

MILK CONTAINER MAINTENANCE AND CLEANING...........................................................................................................................40

CLEANING THE BREW GROUP .................................................................................................................................................42

GRINDER MAINTENANCE ......................................................................................................................................................43

ERROR CODES ..............................................................................................................................................44

TECHNICAL DATA ..........................................................................................................................................45

SAFETY RULES .............................................................................................................................................46

TABLE OF CONTENTS

3

The coffee machine is intended for preparing espresso by using either coffee beans or ground coffee. It
includes an automatic device for preparing milk beverages and a hot water dispenser.
The machine is elegantly designed for domestic use and is not suitable for continuous heavy duty or
professional use.

Warning: no liability is assumed for any damage caused by:

• Incorrect use not in accordance with the intended uses;

• Repairs not carried out by authorized customer service centers;

• Tampering with the power cord;

• Tampering with any part of the machine;

• The use of non-original spare parts and accessories;

• Failure to descale the machine or use at temperatures below 0°C.

IN THESE CASES, THE WARRANTY IS NOT VALID.

Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee
machine. For further information or if you experience problems not completely or suffi ciently addressed in these
instructions, please contact an Authorized Customer Service Center.

KEEP THESE INSTRUCTIONS

A WARNING TRIANGLE DRAWS ATTENTION TO ALL THE INSTRUCTIONS THAT
ARE IMPORTANT FOR USER SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS
CAREFULLY TO AVOID SERIOUS INJURY!

HOW TO USE THESE OPERATING INSTRUCTIONS

GENERAL INFORMATION

4

Cappuccinatore

maintenance kit

Compartment for pre­ground coffee

Brew group

Coffee grounds drawer

Socket for
power cord

Open coffee bean hopper

button

Coffee bean hopper

Cup warming plate

Main switch

Service door

ACCESSORIES

Coffee bean hopper cover

Drip tray

Button for raising/lowering
the drip tray

TOUCH SCREEN Display

SBS

Dispensing head

Drip tray + grill and fl oat

Compartment for milk
container

Hot water spout

Water tank

Intenza water fi lter

Ground coffee

measuring scoop

Cleaning detergent

(Brew group)

Water hardness

tester

Grinder

adjustment key

MACHINE

Lubricant for the

brew group

Detergent for cleaning

milk container

Milk compartment
button

5

1 2 3

4

7

65

INSTALLATION

Attach the female end of the
power cord to the machine. Insert
the male end into the power
outlet.

Place a container beneath the hot
water spout.

Press the button on the coffee
hopper to open the cover. Fill the
hopper with coffee beans.

Close the cover pushing it down
completely.

Remove the water tank.
We recommend installing the water
fi lter (see page 7).

Press the main switch once to turn
on the machine. The appliance
automatically performs a diagnosis
of its functions. This test is
performed each time the machine
is turned on.

The machine automatically primes the water circuit.
The machine is now ready for use.
Water may not be dispensed into the glass.
This should not be considered a malfunction.

Make sure that the main power button is not switched to the “ON” position.

Fill the tank with fresh drinking
water. Do not exceed the “max”
level indicated on the water tank.
Once fi lled place the tank back
into the machine.

STARTING THE MACHINE

TO ADJUST THE WATER HARDNESS LEVEL AND SET

THE INTENZA AROMA SYSTEM SEE THE «WATER

HARDNESS MENU» ON PAGE 20.

6

1 3

Press to select the desired
language.

The machine starts and displays
the menu in the selected
language.

See manual on page 34 to
adjust the clock.

5

italiano (ch)

language

1/2

français

deutsch

nederlands

english

Italiano ( i)

ok

1

Select the desired language.
Press

for the other languages.

Press “ok”.

demo

self-test

4

italiano (ch)

language

1/2

français

deutsch

nederlands

english

Italiano ( i)

ok

2

italiano (ch)

language

1/2

français

deutsch

nederlands

english

Italiano ( i)

ok

3

If desired, the “demo” function (see page 26)
may be activated by pressing the key, each time
the machine carries out a self-diagnosis.

demo

self-test

4

MANUAL PRIMING OF THE WATER CIRCUIT

Position a container under the hot
water spout (it is possible that
water will not come out of the
spout).

Press the display once and the
machine will begin priming the
water circuit.

When the prime circuit cycle is
fi nished, remove the container.
The machine is now ready for
use.

INSTALLATION

SETTING THE LANGUAGE AND THE CLOCK

When the machine is switched-on for the fi rst time, it requires the selection of the desired language.
This allows you to adjust the parameters of the beverages to the typical parameters of the country
where the machine is used. This is why some languages are differentiated also by country.

2

start

priming the machine

position the SBS system as shown

Manually prime the water circuit only when display (2) appears.
Note: fi rst make sure that the water tank is full.

Important: before performing the circuit priming, position the SBS system (see page 9) as shown on the
display. Then adjust as desired.

7

5

6

9

4

1

3

2

Remove the small white fi lter
from the tank and store it in a dry
place sheltered from dust.

Fill the tank with fresh drinking
water and reinsert it into the
machine.

Set the Intenza Aroma System:
A = Light water
B = Medium water (standard)
C = Hard water
For further details see page 20

INTENZA WATER FILTER

To improve the quality of the water you use, and extend the life of your machine at the same time, it is
recommended that you install the water fi lter. After installation, go to the water fi lter initialization program
(see programming). In this way, the machine informs the user when the water fi lter must be replaced.

Remove the water fi lter from its packaging, immerse it vertically (with the opening facing upwards)
in cold water and gently press its sides so as to let the air bubbles out.

Insert the fi lter in its place within
the empty tank (see fi gure).
Press down until it clicks into
place.

Press "machine settings".

Press "water fi lter".

Press "water fi lter activation".

water

fi lter

inserted

not

inserted

water fi lter

activation

The machine performs the water fi lter initialization. Wait until the cycle stops automatically.
At the end of the initialization cycle, the machine returns to the product selection menu. Do not use the water
dispensed during this phase.

NOTE: if the Intenza water fi lter is not available, insert the small white fi lter previously removed (see
point 1) into the tank.

Place a container beneath the
hot water spout.

Press "programming menu".

show icon

explanation

my custom

coffee

program-

ming
menu

main-

tenance

main

menu

specials

machine
settings

clock

settings

extras

beverage

settings

energy
saving

back to

coffee

menu

alerts &
acoustic
settings

machine

settings

display

language

rinsing

water

hardness

water

fi lter

cup

illumination

cup

warmer

go back

restore
default

settings

back to

menu

go back

restore
default

settings

back to

menu

save

settings

8

7

8

• To get the desired beverage, press the corresponding symbol on the display.
The machine automatically performs all the necessary operations.

• To make 2 cups, press the beverage symbol twice.

press twice

weak medium strong

The intensity of the color on the cup icon (only valid for coffee beverages) indicates the aroma, or
quantity of coffee to be ground, for preparing the beverage. The greater the quantity of coffee
ground the stronger the coffee will taste.

DISPLAY

Go to the "text
format" menu

Beverage
programming

Accessing the
programming menu

It is possible to change the type of display and choose between " icon format" and "text format"

ICON FORMAT

long

coffee

hot

water

coffee espresso

hot

milk

latte

macchiato

espresso

macchiato

cappuccino

medium strongmedium

medium strongmedium

Go to the "icon
format" menu

TEXT FORMAT

CHOOSE COFFEE AROMA

When the machine is programmed to use pre-ground coffee or when a beverage is customized, the
icon is displayed in a different way and/or accompanied by an asterisk (see section on
“programming beverages”.)

pre-ground customization

show icon

explanation

my custom

coffee

program-

ming
menu

show

icon

my custom

coffee

program-

ming

menu

9

MEDIUM

COFFEE

STRONG
COFFEE

MILD

COFFEE

SBS adjusts the intensity of the brewed coffee,
and can even be adjusted while brewing. Any
adjustment has an immediate effect on the
brewing coffee.

COFFEE INTENSITIY

SBS – SAECO BREWING SYSTEM

Height adjustable drip tray.

To raise the drip tray, press lightly on the lower part of the button. To lower the tray,
press lightly on the upper part of the button; when the desired height is reached,
release the button.

Note: There is a red fl oater in the drip tray. When it rises, the tray must be emptied
and washed.

ADJUSTING THE HEIGHT OF THE DRIP TRAY

FILLING THE MILK CONTAINER

ADJUSTMENTS

The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply
turn the dial and you will notice that the coffee goes from mild intensity to strong intensity.

Only the container with the cappuccinatore must be fi lled before preparing beverages with milk. Do not
use milk after the best-before date. (Important! Refer to the instructions for maintenance and cleaning

of the cappuccinatore on page 40).

Adjust the drip tray before dispensing any beverages.

21 3

Open the milk compartment by
pressing the button and remove
the milk container.

Remove the cover and pour in the
milk. DO NOT EXCEED THE
MAXIMUM LEVEL shown in the
fi g u r e .

Replace the lid on the container
and place it back in the milk
compartment. Make sure to
carefully close the compartment.

S

C

10

1 2

3

DISPENSING COFFEE, HOT WATER AND MILK CAN BE INTERRUPTED AT ANY TIME BY
SELECTING THE "STOP ... DISPENSING" BUTTON.

THE DISPENSED MILK CAN REACH HIGH TEMPERATURES: THERE IS A DANGER OF
SCALDING. DO NOT TOUCH IT WITH BARE HANDS.

Check that all the containers are clean. To do this operation, follow the instructions in the "Cleaning and
Maintenance" (see page 39).

WHEN YOU HAVE FINISHED PREPARING BEVERAGES CONTAINING MILK, PROCEED WITH
CLEANING THE CONTAINER AND THE MACHINE'S CIRCUIT.

To brew 2 cups, the machine dispenses half of the entered quantity and briefl y interrupts dispensing in
order to grind the second serving of coffee. Coffee dispensing is then restarted and completed.If a milk
beverage has been chosen, the machine automatically dispenses the milk. If the fi rst coffee is interrupted,
the second will not be dispensed.

THE MILK USED MUST HAVE BEEN PROPERLY PRESERVED.
DO NOT USE IT AFTER THE EXPIRATION DATE ON THE PACKAGE.

ESPRESSO / COFFEE / LONG COFFEE

Choose the beverage and press
the corresponding icon on the
display: once for 1 cup and twice
for 2 cups.

The machine begins grinding the
quantity of coffee entered.

Begin dispensing the selected
beverage.

stop

coffee

dispensing

espresso

BEVERAGE DISPENSING

This procedure shows how to dispense an espresso. To dispense another type of coffee, press the
appropriate icon. Use appropriate espresso or coffee cups so that the coffee will not overfl ow.

The machine ends dispensing automatically according to the quantity determined by the manufacturer. It is
possible to customize this quantity. See page 15.

If you wish to interrupt the dispensing cycle, press the " stop coffee dispensing" button.

show icon

explanation

my custom

coffee

program-

ming

menu

11

1 2 3

4 5

DISPENSING BEVERAGES WITH GROUND COFFEE

Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean
hopper. Pour in only coffee ground for espresso machines and never coffee beans or instant coffee. (see the
"Beverage programming" chapter on page 15).

WARNING: PUT PRE-GROUND COFFEE IN THE COMPARTMENT ONLY WHEN YOU WISH TO
DISPENSE THIS TYPE OF BEVERAGE.

INSERT ONLY ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE
DISPENSED AT THE SAME TIME.

Press the appropriate button and
the display will show:

A message appears, reminder the
user to pour ground coffee in the
appropriate compartment.

add preground

coffee

start!

go

back

Press the "start! "button to start
dispensing.

Pour ground coffee into the pre­ground coffee compartment using
the measuring scoop provided
with the accessories.

add preground

coffee

start!

go

back

Begins dispensing the selected
beverage.

long

coffee

stop

coffee

dispensing

Note:

• After 1 minute from when the message appears (2), if brewing has not started the machine will return to
the main menu and dump any inserted coffee into the coffee grounds drawer.

• If no pre-ground coffee is poured into the compartment, only water will be dispensed.

• If 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the
compartment will be dumped into the coffee grounds drawer.

In the example given below, we chose to dispense a long coffee using pre-ground coffee.
The customized choice of using pre-ground coffee is shown on the display with an asterisk next to the
chosen beverage.

show icon

explanation

my custom

coffee

program-

ming

menu

12

2

2

3

4 5

1

1

6

Press the hot water icon once.

HOT WATER DISPENSING

WHEN THE HOT WATER BEGINS TO DISPENSE, SHORT SPURTS OF HOT WATER MAY BE
DISPENSED WHICH POSE A RISK OF SCALDING. THE HOT WATER SPOUT CAN REACH
HIGH TEMPERATURES: AVOID TOUCHING IT WITH BARE HANDS.

Begin hot water dispensing.

To dispense another cup of
hot water, repeat this
operation.

BEVERAGE DISPENSING

latte

macchiato

latte

macchiato

latte

macchiato

The machine begins grinding the
quantity of coffee entered.

Select the beverage and press the
corresponding icon on the
display: once for 1 cup and twice
for 2 cups.

When the coffee fi nishes grinding,
the machine will automatically
dispense the programmed quantity
of hot milk.

Once milk has been dispensed, the
machine automatically prepares the
coffee.

After this, the machine allows you to
dispense more milk if you wish. This
option remains active for
approximately 2 seconds. To activate,
press the “add milk” button.

The “milk rinsing” icon will fl ash
once the machine is done
dispensing in order to clean the
milk circuit. Press the “milk
rinsing” icon to clean the internal
milk circuit.

stop
milk

dispensing

add
milk

stop

water

dispensing

hot

water

milk

rinsing

Fill the milk container

LATTE MACCHIATO

show icon

explanation

my custom

coffee

program-

ming
menu

show icon

explanation

my custom

coffee

program-

ming

menu

show icon

explanation

my custom

coffee

program-

ming

menu

stop

coffee

dispensing

stop

milk

dispensing

stop

coffee

dispensing

SEE INSTRUCTIONS ON PAGE 40 FOR OPTIMAL MILK DISPENSING

13

9

start

rinsing

milk rinsing cycle

8

rinsing...

rinsing milk circuit-

please wait

If the user wishes to continue preparing other drinks the
machine will keep the “milk rinsing” signal active.

After 20 minutes of inactivity, the machine requires the user
to perform a rinsing cycle as described in Step 7.
If the machine is turned off immediately after dispensing a
milk beverage, the next time the machine is turned on it will
require the user to perform a rinsing cycle.

Note: Before performing the “milk rinsing” function make
sure that:

1. an adequate sized container is placed under the
dispensing head

2. the water tank is full of fresh water.

7

To perform a rinse cycle,
press “start rinsing”.

Wait for the cycle to be completed.
After this, the machine returns to
the main menu.

THIS PROCEDURE MUST BE PERFORMED FOR ALL MILK BEVERAGES!

AFTER USE, ALWAYS REMOVE THE MILK CONTAINER AND PUT IT IN THE REFRIGERATOR IF IT

CONTAINS REMAINING MILK.

Remove the container and put
it in the refrigerator if it
contains remaining milk.

THE CONTAINER MAY BE LEFT IN THE MACHINE ONLY IF IT HAS BEEN WASHED WITH

DRINKING WATER AND IT DOES NOT CONTAIN MILK (SEE PAGE 40).

After performing the rinse cycle, the machine reminds the user to
remove the container with the remaining milk through the message
“remove milk”.

REMOVE THE MILK CONTAINER ONLY WHEN THE MACHINE IS ON.

show icon

explanation

my custom

coffee

program-

ming

menu

remove

milk

milk

cleaning

show icon

explanation

my custom

coffee

program-

ming

menu

After 14 days from the fi rst dispensing of
a milk-based beverage, the message
“milk cleaning” is displayed; it is
advisable to clean the milk circuits as
shown on page 28.

After another 7 days the machine stops
dispensing milk-based beverages and the
milk circuits must be washed; during this
phase, coffee and hot water may be
brewed.

14

2

31

4

5

2

3

4 5

1

BEVERAGE DISPENSING

espresso

macchiato

espresso

macchiato

cappuccino

cappuccino

cappuccino

ESPRESSO MACCHIATO

The machine begins grinding the
quantity of coffee entered.

Press the icon once for 1 cup and
twice for 2 cups.

Espresso macchiato begins
brewing.

Once the coffee has been brewed,
the machine automatically prepares
the hot milk.

CAPPUCCINO

The machine begins grinding the
quantity of coffee entered.

Press the icon once for 1 cup and
twice for 2 cups.

After this, the machine allows you to dispense more milk if you wish.
Press the “add milk” button within 2 seconds.

Fill the milk container

Fill the milk container

When the "milk rinsing"
symbol fl ashes, clean the
milk circuits as described for
latte macchiato (see page 12,
Step 6).

When the "milk rinsing"
symbol fl ashes, clean the
milk circuits as described for
latte macchiato (see page 12,
Step 6).

When the coffee fi nishes grinding,
the machine will dispense the
programmed quantity of hot milk.

Once milk has been dispensed, the
machine automatically prepares the
coffee.

add

milk

To dispense more milk, press the
“add milk” icon.

espresso

macchiato

show icon

explanation

my custom

coffee

program-

ming

menu

show icon

explanation

my custom

coffee

program-

ming

menu

stop
milk

dispensing

stop

coffee

dispensing

stop

milk

dispensing

stop

coffee

dispensing

stop
milk

dispensing

stop

coffee

dispensing

stop
milk

dispensing

stop

coffee

dispensing

add

milk