Sabine SW75-T BELTPACK TRANSMITTER User Manual

SW75-T Beltpack Transmitter Quick Setup Guide

PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS.

Select the INPUT to Match your Input Type

1

1

2

SELECT

MICROPHONE INSTRUMENT

UPDOWN

SIDE

A

Select INPUT function: Push the transmitter’s
SELECT button to scroll through functions until
the word INPUT appears at bottom in the trans­mitter LCD, which stays backlit while you are
editing all parameters.

NOTE: Electric Guitar & Bass: For best results, put your receiver’s FBX Feedback Exterminator into
BYPASS mode. BYPASS is accessible via the receiver front panel or Remote Software control.

Adjust PAD Settings to Match your Input Level

2

As in all audio equipment, the setting of the input level is crucial to achieving the best sound quality. Setting
minimal PAD levels (-3, -6, or -10 dB) may produce a distorted sound if you are using a high output microphone
or instrument. Conversely, setting a more extreme PAD level (-40, -37, or -34 dB) may require you to raise
your system gain unnecessarily, resulting in a noisier output. Set your level so there are at least three indica­tors illuminated on the audio meter, with an occasional move to the fourth indicator. The fifth and biggest
indicator denotes clipping. If you see clipping, choose a lower pad setting (for example, go from -10 to -14 dB).

Changing PAD Settings

1

SELECT

Select PAD function: Press the
SELECT button to scroll through
functions until PAD flashes in the
transmitter LCD.

Suggested PAD Settings - adjust for your application

♦ SWT31L-TA4

Cardioid Lav

Sabine

♦ Microphones

low-output

General

-10 dB -17 dB -23 dB -26 to -34 dB -37 dB

PAD

♦ Microphones

standard

♦ Acoustic

instruments

low-gain pickups

2

UPDOWN

Select PAD setting: Use the UP
or DOWN buttons to select the
desired setting. Selection is
stored after 3 seconds.

♦ SWT73W-TA4
♦ SWT56W-TA4

Cardioid
Headworns

♦ Electric guitars

low-gain pickups

♦ Microphones

higher gain

Select INSTR or MIC: Use the UP or DOWN but­tons to select your desired input (Instrument or
Microphone). This important selection optimizes
the input section of the transmitter. Your selection
is stored after 3 seconds.

Clipping
Zone

3

Check for Clipping: Make sure
the receiver’s Audio Level Meter
stays out of the Clipping Zone.

♦ SWTVT50-TA4

Omni Lav

♦ SVT40L-TA4

Omni Lav

♦ SVT80BW-TA4
♦ SVT81LW-TA4

Cardioid Headworns

♦ Electric guitars

standard

♦ SVT70LW-TA4
♦ SVT70BW-TA4

Omni
Headworns

♦ Instruments

high-gain pre­amps

Set Low-Cut Filter to Match your Sound

3

1

SELECT

Select LOW CUT function: Push the
transmitter’s SELECT button to scroll through
functions until L 0 or L 75 appears on the transmit­ter LCD.

Battery RUN TIME Hours

4

1

To view Run-time Hours: Use the
transmitter’s SELECT button to scroll
through functions until TIME appears in
the LCD.

© 2007 Sabine, Inc.

Toggles between no filter and 12 dB/octave low frequency roll-off filter
(starting at 75 Hz).

2

UPDOWN

Select LOW CUT setting: Use the UP or DOWN
buttons to toggle between no filter (indicated in the
display as L 0) or a roll-off at 75 Hz (indicated by L 75).

Resets the display that indicates the length of power-on time (hours and minutes) since the last
battery change or recharge.

USER TIP: FOR ELECTRIC

& BASSES USE L0;

GUITARS
SOME ACOUSTIC INSTRUMENTS

BENEFIT FROM L75.

MAY

2

UPDOWN

To Reset Run-time hours: Simultaneously press
and hold both the UP and DOWN arrows until LCD
resets to 0.00.

NOTE: RUN-TIME HOURS ARE RESET AUTOMATICALLY

CHARGING BATTERIES.

WHEN

LIT-SW75T-QG-EN-070223.pmd

SW75-T Beltpack Transmitter Quick Setup Guide

Opening Access Compartment

SIDE

B

1

Using your thumb and forefinger, grab both tabs

and simultaneously pull down toward the bottom
of the beltpack. This releases the locks.

Closing Access Compartment

Swing the door back up and close it by firmly
pushing the top part of the door in until you hear
the locks click.

2

Gently pull the door open.

Important Battery Information

Your Sabine 2.4 GHz beltpack transmitter (SW75-T) comes with two size AA rechargeable NiMH batteries.
For best results, charge the battery for at least 8 hours before using it for the first time. Please note that the
full charging potential of the battery will be achieved after the first 5 charging cycles have been completed.

These rechargeable NiMH batteries are highly resistant to the “memory effect,” which affects some recharge­able batteries. The included batteries will provide more lifetime charges and longer battery life for each charge
than many rechargeable batteries.

Acceptable Batteries for use with SW70-T Beltpack Transmitters

2 “AA” size (14.5x50.5mm,

• NiMH Rechargeable (Sabine part #: SWBAA2)

• Alkaline: NEDA 14A - ANSI 14A - IEC LR14

• Heavy Duty batteries (NOT recommended)

WARNING! DO NOT USE: Alkaline Rechargeable Batteries

Alkaline “AA”

Rechargeable

Batteries

Battery Caution

DO NOT BURN OR PUNCTURE BATTERY.
DOING SO COULD RELEASE TOXIC MA-

DO NOT SHORT CIRCUIT. MUST BE RE­CYCLED OR DISPOSED OF PROPERLY.

TERIALS WHICH COULD CAUSE INJURY.

PLEASE CAREFULLY READ THE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS.

®

SABINE

13301 NW US Highway 441 • Alachua, FL 32615-8544 USA • +USA [phone] • +USA [phone] fax

© 2007 Sabine, Inc.

[e-mail] • www.Sabine.com

)