SA-SC8/WS8/SS-CT8/TS8
SERVICE MANUAL
Ver 1.1 2004. 09
• SA-SC8 is the speaker section in
DAV-FC9/SC8.
• SA-SC8 is composed of following models.
SA-SC8
FRONT and SURROUND speakers SS-TS8
CENTER speaker SS-CT8
SUBWOOFER SA-WS8
SA-WS8
SS-CT8 SS-TS8
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
SPECIFICATIONS
Front/Surround
Speaker system Bass reflex
Speaker unit 70 mm dia. cone type × 2,
25 mm dia. balance dome
Rated impedance 4 ohms
Dimensions (approx.) 250 × 1196 × 250 mm
(w/h/d, Max size with the
stand)
250 × 646 × 250 mm
(w/h/d, Min size with the
stand)
Mass (approx.) 3.62 kg
Centre
Speaker system Bass reflex
Speaker unit 70 mm dia. cone type × 2,
25 mm dia. balance dome
Rated impedance 4 ohms
Dimensions (approx.) 379 × 125 × 85 mm
(w/h/d, with the stand)
Mass (approx.) 1.07 kg
Subwoofer
Speaker system Active subwoofer,
Speaker unit 20 cm dia. cone type
Enclosure type Advanced SAW type
Amplifier section
Continuous RMS power output
EXCEPT US and Canadian models:
US and Canadian models:
Power requirements
US and Canadian models:
Australian and Asian models:
Taiwan model: 120 V AC, 50/60 Hz
Other models: 110 – 120 V/220 – 240 V
Power consumption 90 W, 1 W (standby mode)
Dimensions (approx.) 230 390 475 mm
Mass (approx.) 14.5 kg
Design and specifications are subject to change
without notice.
Magnetically shielded
135 W (8 ohms,
20 Hz -20 kHz, 10% THD)
150 W (6 ohms,
20 Hz – 20kHz, 10% THD)
120 V AC, 60 Hz
220 – 240 V AC, 50/60 Hz
AC, 50/60 Hz
(w/h/d) incl. front grille
9-961-138-02
2004I16-1
© 2004.09
SUBWOOFER/SPEAKER SYSYTEM
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
SA-SC8/WS8/SS-CT8/TS8
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for A C leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a V OM
or battery-operated A C v oltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate lo w-v oltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
TABLE OF CONTENTS
1. DIAGRAMS
1-1. CIRCUIT BOARDS LOCATION (SA-WS8) .............. 3
1-2. PRINTED WIRING BOARDS (SA-WS8)................... 5
1-3. SCHEMATIC DIAGRAM (SA-WS8)..........................6
2. EXPLODED VIEWS
2-1. SS-CT8 (OVER ALL SECTION)··································· 7
2-2. SS-TS8 (OVERALL SECTION)····································8
2-3. SS-TS8 (STAND SECTION) ········································· 9
2-4. SA-WS8 (OVERALL SECTION) ································10
2-5. SA-WS8 (AMP SECTION)··········································11
3. ELECTRICAL PARTS LIST········································· 12
To Exposed Metal
Parts on Set
0.15
µ
F
1.5k
Ω
Earth Ground
AC
voltmeter
(0.75V)
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH SONY
PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN
THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
À LA SÉCURITÉ!!
2
SA-SC8/WS8/SS-CT8/TS8
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/
specified.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
• A : B+ Line.
• B : B– Line.
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
•Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage var iations may be noted due to normal production tolerances.
• Signal path.
F : AUDIO
•Abbreviation
CND : Canadian model.
Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• : Pattern from the side which enables seeing.
4
W or less unless otherwise
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
• Semiconductor
Location
Ref. No. Location
D201 I-4
D202 H-4
D303 E-3
D304 E-3
D305 F-6
D306 D-8
D501 C-8
D502 E-8
D503 E-8
D504 E-8
D505 E-8
D506 F-7
D507 E-7
D601 I-7
D602 I-7
D603 J-7
D604 I-7
D605 H-7
D606 G-7
(D607) J-9
<D608> G-8
D701 B-5
D702 C-5
D703 C-5
D704 C-5
D801 E-10
IC101 C-3
IC102 C-2
IC104 C-5
IC201 H-3
IC202 H-1
IC203 H-3
IC204 H-4
IC301 E-2
IC701 B-6
Q101 C-1
Q301 E-3
Q302 E-2
Q303 E-2
Q304 D-2
Q305 D-3
Q306 D-3
Q307 D-3
Q308 E-7
Q309 F-6
Q310 E-6
Q311 E-6
Q401 J-3
Q402 J-3
Q403 J-2
Q404 J-5
Q501 F-7
Q502 E-7
Q601 H-7
Q602 G-7
Q701 B-5
Q702 C-6
Q703 A-7
Q704 A-7
Q705 A-7
(): Except E model
<>: E model
4