Page 1
OPERAT OR’S MANUAL
LAMINATE TRIMMER
MODEL TR31-1
DOUBLE INSULATED
SPECIFICATIONS:
Maximum Cutter Diameter 1-3/8 in. (34.9 mm)
Collet 1/4 in. (6.4 mm)
Horsepower 3/4
Rating 120 volts, 60 Hz AC only, 3.8 amperes
No Load Speed 23,000 RPM
Power Cord 10 ft. (3 m)
Net Weight 3.0 lbs. (1.4 kg.)
We have engineered and manufactured your new Laminate Trimmer to Ryobi’s high standard for dependability, ease of
operation, and operator safety. When properly cared for, the Laminate Trimmer will give you years of rugged, trouble-free
performance.
WARNING: Carefully read through this entire operator’s manual before using your new trimmer.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 2
TABLE OF CONTENTS
■ Introduction..................................................................................................................................................... 2
■ General Safety Rules ..................................................................................................................................3-4
■ Specific Safety Rules...................................................................................................................................... 4
■ Symbols.......................................................................................................................................................... 5
■ Unpacking....................................................................................................................................................... 6
■ Features ...................................................................................................................................................... 6-7
■ Adjustments.................................................................................................................................................7-8
■ Operation................................................................................................................................................... 9-11
■ Maintenance ................................................................................ ............................................................... 12
■ Accessories ............................................................................................................................................. 13-15
INTRODUCTION
DOUBLE INSULATION
Your Ryobi power tool is double insulated. Double insulation
is a concept in safety , in electric power tools, which eliminates
the need for the usual three-wire grounded power cord. All
exposed metal parts are isolated from internal metal motor
components with protecting insulation. Double insulated tools
do not need to be grounded.
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal wiring. Observe all normal safety precautions
related to avoiding electrical shock.
WARNING:
The operation of any laminate trimmer can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with
side shields. Always wear eye protection which is marked to comply with ANSI Z87.1.
IMPORTANT
Servicing of a tool with double insulation requires extreme
care and knowledge of the system and should be performed
only by a qualified service technician. For service we suggest
you return the tool to your nearest RYOBI AUTHORIZED
SERVICE CENTER for repair. When servicing use only
identical Ryobi replacement parts.
WARNING:
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save operator's manual
and review frequently for continuing safe operation, and
instructing others who may use this tool.
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 2
Page 3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
■ Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
■ Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical Safety
■ Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation eliminates the need for the
three wire grounded power cord and grounded power
supply system.
■ Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is a n
increased risk of electric shock if your body is grounded.
■ Don't expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
■ Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately . Damaged cords
increase the risk of electric shock.
■ When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords are
rated for outdoor use and reduce the risk of electric shock.
Personal Safety
■ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operat-
ing power tools may result in serious personal injury .
■ Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry ,
or long hair can be caught in moving parts.
■ Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites accidents.
■ Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
■ Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
■ Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Tool Use and Care
■ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
■ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it is designed.
■ Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is dangerous and must be repaired.
■ Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing the tool. Such preventive safety measures re-
duce risk of starting the tool accidentally.
■ Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
■ Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
■ Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
■ Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may become hazardous when
used on another tool.
Service
■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
■ When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of electric shock or injury.
Page 3
Page 4
GENERAL SAFETY RULES
■ Keep the tool and its handle dry , clean, and free from
oil and grease. Always use a clean cloth when clean
SPECIFIC SAFETY RULES
Additional Rules for Safe Operation
■ Know your power tool. Read operator's manual care-
fully. Learn its applications and limitations as well as the
specific potential hazards related to this tool. Following
this rule will reduce the risk of electric shock, fire, or
serious injury.
■ Always wear safety glasses with side shields. Every-
day eyeglasses have only impact resistant lenses; they
are NOT safety glasses.
■ Protect your lungs. Wear a face or dust mask if the
operation is dusty.
■ Protect your hearing. Wear hearing protection during
extended periods of operation.
■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live"
and shock the operator.
■ Inspect tool cords periodically and if damaged, have
repaired at your nearest authorized service center. Stay
constantly aware of cord location.
■ Check damaged parts. Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
■ Do not abuse cord. Never carry tool by cord or yank
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges. Following this rule will reduce
the risk of electric shock or fire.
ng. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your
■ Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. A wire
gage size (A.W.G.) of at least 16 is recommended for an
extension cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next
heavier gage. The smaller the gage number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
■ Drugs, Alcohol, Medication. Do not operate tool while
under the influence of drugs, alcohol, or any medication.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■ Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also.
tool.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
SAVE THESE INSTRUCTIONS
Page 4
Page 5
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Alternating Current Type or a characteristic of current
--- Direct Current Type or a characteristic of current
n
0
.../min
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol Meaning
No Load Speed Rotational speed, at no load
Class II Construction
Revolutions or Reciprocation Per Minute
Safety Alert
Wet Conditions Alert
Designates double-insulated construction
tools
Revolutions, strokes, surface speed,
orbits etc. per minute
Indicates danger, warning or caution.
It means attention!!! Your safety is involved.
Do not expose to rain or use in damp
locations.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in serious
injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
Page 5
Page 6
UNPACKING
Your trimmer has been shipped completely assembled and
ready for use. After removing it from the carton, inspect it
carefully to make sure no breakage or damage has occurred
during shipping. If any parts are damaged or missing, contact your nearest Ryobi dealer to obtain replacement parts
before attempting to operate trimmer. A subbase accessory
with handles, operator's manual, warranty registration and
two wrenches are included in the carton.
FEATURES
WARNING:
If any parts are missing do not operate your trimmer until
the missing parts are replaced. Failure to do so could
result in possible serious injury.
KNOW YOUR TRIMMER
See Figure 2.
Before attempting to use your trimmer, familiarize yourself
with all operating features and safety requirements.
Your trimmer is a versatile woodworking tool which will give
you years of trouble-free performance. It is engineered with
the professional in mind, but its ease of operation allows the
amateur to produce work which is beautiful and precise.
As the name implies your trimmer can be used for trimming
laminates. When used with recommended accessories, such
as a straight guide, trimmer guide, template guide, or combination panel bit, it becomes even more versatile.
WARNING:
Do not allow familiarity with your trimmer to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict severe injury.
HEAVY DUTY MOTOR
Your trimmer has a powerful 3.8 amp motor with sufficient
power to handle many trimming jobs. It is capable of delivering 3/4 horsepower for heavy duty performance. The
motor also has removable brushes for ease of servicing.
SWITCH
To turn your trimmer ON, slide the switch on top of the
trimmer to ON position. Return the switch to OFF position
when finished.
DEPTH OF CUT SCALE
Your trimmer's cutting depth can be adjusted by using the
depth of cut scale. To adjust to desired depth of cut, loosen
the wing bolt and move the base until the tip of the cutter
touches work surface. The depth of cut is zero at this point.
Position your trimmer so that the cutter can extend below
the subbase for desired depth of cut setting. Move the base
further until the mark on the depth of cut scale corresponds
with your desired depth of cut. Then securely tighten the
wing bolt.
ELECTRICAL CONNECTION
Your trimmer has a precision built electric motor. It should
be connected to a power supply that is 120 volts, 60 Hz,
AC only (normal household current). Do not operate this
tool on direct current (DC). A substantial voltage drop will
cause a loss of power and the motor will overheat. If your
tool does not operate when plugged into an outlet, doublecheck the power supply.
WARNING:
The operation of any trimmer can result in foreign objects
being thrown into your eyes, which can result in severe
eye damage. Before starting power tool operation, always
wear safety goggles or safety glasses with side shields
and a full face shield when needed. We recommend wide
vision safety mask for use over eyeglasses or standard
safety glasses with side shields.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
APPLICATIONS
(Use only for the purpose listed below)
■ Smooth, professional trimming of laminates.
■ Cabinet making, trimming counter tops, and finishing
work.
■ Trimming wood and plastics.
BALL BEARING PILOTED CUTTER
See Figures 1 and 5.
Use of ball bearing piloted trimmer cutters provide a convenient method of laminate trimming. Guide the ball bearing
surface along the edge of workpiece. Be careful to follow
instructions for correct direction of feed
.
Page 6
Page 7
ON-OFF
SWITCH
FEATURES
OFF
BASE
ON
BRUSH CAP
MOTOR
HOUSING
SUBBASE
WING BOLT
WRENCH (2)
COLLET NUT
ON
OFF
1
3/4
1/2
DEPTH OF
CUT SCALE
COLLET
ADJUSTMENTS
WARNING:
Your laminate trimmer should never be connected to
power supply when you are assembling parts, making
adjustments, installing or removing cutters, or when not
in use. Disconnecting your trimmer will prevent accidental
starting that could cause serious injury.
WARNING:
Do not use cutters with undersized shanks. Undersized
shanks will not tighten properly and could be thrown from
tool causing injury.
Fig. 2
WARNING:
Do not use cutters that are larger in diameter than the
opening in trimmer base. Use of such cutters will come
in contact with the trimmer base and damage both the
cutter and trimmer base. This situation could also cause
possible loss of control or create other hazardous
conditions that could cause possible serious personal
injury.
Page 7
Page 8
ADJUSTMENTS
INSTALLING/REMOVING CUTTERS
See Figure 3.
■ UNPLUG YOUR TRIMMER.
WARNING:
Failure to unplug your trimmer could result in accidental
starting causing serious injury.
■ Place your trimmer upside down on a workbench in order
to gain easy access to the spindle and collet nut.
■ Place the small end of one of the wrenches provided on
the spindle flats. This will hold the spindle stationary.
■ Place the large end of the other wrench provided onto the
collet nut. Rotate wrench counterclockwise to loosen
collet nut.
See Figure 3.
WARNING:
If you are changing a cutter immediately after use, be
careful not to touch the cutter or collet with your hands or
fingers. They will get burned because of the heat buildup
from cutting. Always use the wrench provided.
WRENCH ON
COLLET NUT
ON
CUTTER
WRENCH ON
SPINDLE FLATS
Fig. 3
OFF
■ If installing cutter for the first time, it can be installed once
collet nut is loose. If changing cutters, cutter will easily slip
from collet after loosening collet nut.
■ The collet is machined to precision tolerances to fit cutters
with 1/4 in. (6.4 mm) diameter shanks.
■ With your trimmer still upside down on a workbench, insert
shank of cutter into collet. The shank of your cutter should
be close to but not touching bottom of collet. This allows
for expansion when the cutter gets hot.
■ Tighten the collet nut securely by turning clockwise with
the wrench provided.
See Figure 3.
WARNING:
If collet nut is not tightened securely, cutter may come
out during use, causing serious personal injury.
WARNING:
Avoid open area of trimmer base. Serious personal injury
will result from contact with a rotating cutter.
TO SET DEPTH OF CUT
See Figure 4.
■ UNPLUG YOUR TRIMMER.
WARNING:
Failure to unplug your trimmer could result in accidental
starting causing serious injury.
INDICATOR
POINT(S)
DEPTH OF
1
3/4
1/2
WING
BOLT
■ Loosen the wing bolt and move the base until the tip of
cutter touches the work surface. The depth of cut is zero
at this point.
■ Position your trimmer so that the cutter can extend below
the subbase for desired depth of cut setting.
■ Move the base to obtain the desired depth of cut. The
distance the cutter moves can be read on the depth of cut
scale. Each mark on the scale indicates a 1/16 in. (1.6 mm)
change in depth setting. Indicator points are located on the
base.
■ Securely tighten the wing bolt.
See Figure 4.
CUT SCALE
1
3/4
1/2
1/4
0
INDICATOR
POINT(S)
Fig. 4
Page 8
Page 9
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when using your trimmer. Failure to do so could
result in dust, shavings, chips, loose particles, or foreign
objects being thrown into your eyes resulting in possible
serious injury. If the operation is dusty, also wear a face
or dust mask.
WARNING:
When turning your trimmer ON, be prepared for start-up
torque. Always have a firm grasp of your trimmer before
starting. Because of the high cutter speed rotation your
trimmer has a tendency to twist, jerk, or grab in your hands
during start-up. If not prepared, this can cause a loss of
control resulting in possible serious injury.
HOW TO OPERATE YOUR TRIMMER
Before starting your trimmer, unplug it and make sure cutter
is securely tightened in collet and that depth of cut is properly
set. Never start trimmer while cutter is in contact with the
workpiece.
After completing a cut, pull cutter slightly away from cut
surface. Turn trimmer off and wait for rotating cutter to
completely stop before removing base from work surface.
Your trimmer is turned on by means of a slide switch located
on top of the tool. Make a few cuts on a piece of scrap
material to determine the desired depth or shape of cut.
When cutting, fit the base of your trimmer over the work
surface and firmly hold the body of your trimmer with your
hand. Make sure the trimmer is running at full speed. For best
results, move your trimmer from left to right, against the
turning direction of the cutter.
move trimmer too rapidly.
Remain alert and watch what you are doing. DO NOT
operate trimmer when fatigued or under the influence of
drugs, alcohol, or any medication.
See Figure 5.
Be sure not to
FEED DIRECTION
When trimming, the cutter rotates clockwise. Therefore, you
should feed the trimmer into the workpiece from left to right.
When fed from left to right, the rotation of the cutter pulls the
trimmer against the workpiece. If fed in the opposite direction, the rotation forces of the spinning cutter will tend to
throw the trimmer away from the workpiece. This could
cause loss of control of your trimmer.
RATE OF FEED
IMPORTANT: The whole “secret” of professional laminate
trimming lies in making a careful setup for the cut to be made
and in selecting the proper rate of feed.
The proper rate of feed depends on several factors: the hardness and moisture content of the workpiece, the depth of
Fig. 5
cut, and the cutting diameter of the cutter. When cutting shallow grooves in soft woods such as pine, a faster rate of feed
can be used. When making cuts in hardwoods such as oak,
a slower rate of feed will be required.
The best rate of feed is one that does not slow down the
trimmer motor more than one-third of its no-load speed. If
the trimmer is fed too fast, it will take large chips out of the
wood and leave gouge marks. If the trimmer is fed too slow,
it will scorch or burn the wood.
PROPER FEEDING
The right feed is neither too fast nor too slow. It is the rate at
which the cutter is being advanced firmly and surely to produce a continuous spiral of uniform chips or a smooth trim
edge on laminate. If you are making a small diameter, shallow groove in soft, dry wood, the proper feed may be about
as fast as you can travel your trimmer along your guide line.
On the other hand, if the cutter is a large one, the cut is
deep or the workpiece is hard to cut, the proper feed may
be a very slow one. A cross-grain cut may require a slower
pace than an identical with-grain cut in the same workpiece.
There is no fixed rule. You will learn by experience from
practice and use. The best rate of feed is determined by
listening to the sound of the trimmer motor and by feeling
the progress of each cut. Always test a cut on a scrap piece
of the workpiece wood or laminate beforehand.
FORCE FEEDING
Clean, smooth laminate trimming and edge shaping can be
done only when the cutter is revolving at a relatively high
speed and is taking very small bites to produce tiny , cleanly
severed chips. If your trimmer is forced to move forward too
fast, the speed of the cutter becomes slower than normal in
relation to its forward movement. As a result, the cutter must
take bigger bites as it revolves. “Bigger bites” mean bigger
Page 9
Page 10
OPERATION
chips, and a rougher finish. Bigger chips also require more
power, which could result in the trimmer motor becoming
overloaded.
Under extreme force-feeding conditions the relative speed
of the cutter can become so slow — and the bites it has to
take so large — that chips will be partially knocked off (rather
than fully cut off), with resulting splintering and gouging of
the workpiece.
Your trimmer is an extremely high-speed tool (23,000 RPM
no-load speed), and will make clean, smooth cuts if allowed
to run freely without the overload of a forced (too fast) feed.
Three things that cause “force feeding” are cutter size,
depth-of-cut, and workpiece characteristics. The larger the
cutter or the deeper the cut, the more slowly the trimmer
should be moved forward. If the wood is very hard, knotty,
gummy or damp, the operation must be slowed still more.
You can always detect “force feeding” by the sound of the
motor. Its high-pitched whine will sound lower and stronger
as it loses speed. Also, the strain of holding the tool will be
noticeably increased.
TOO SLOW FEEDING
It is also possible to spoil a cut by moving the trimmer forward too slowly . When it is advanced into the work too slowly ,
a revolving cutter does not dig into new wood fast enough
to take a bite; instead, it simply scrapes away sawdust-like
particles. Scraping produces heat, which can glaze, burn,
or mar the cut — in extreme cases, it can even overheat the
cutter so as to destroy its hardness. Dull cutters can also
contribute to scraping and burning.
In addition, it is more difficult to control a trimmer when the
cutter is scraping instead of cutting. With practically no load
on the motor the cutter will be revolving at close to top RPM,
and will have a much greater than normal tendency to
bounce off the sides of the cut (especially , if the wood has a
pronounced grain with hard and soft areas). As a result, the
cut produced may have sides that are rippled instead of
straight.
“Too-slow feeding” can also cause your trimmer to take off
in a wrong direction from the intended line of cut. You can
detect “too-slow feeding” by the high-pitched sound of the
motor. Always grasp and hold your trimmer firmly when
trimming.
DEPTH OF CUT
See Figure 7.
As previously mentioned, the depth of cut is important
because it affects the rate of feed which, in turn, affects the
quality of a cut (and, also, the possibility of damage to your
trimmer motor and cutter). A deep cut requires a slower feed
than a shallow one, and a too deep cut will cause you to slow
the feed so much that the cutter is no longer cutting, it is
scraping, instead.
Making a deep cut is never advisable. The smaller cutters—
especially those only 1/16 in. (1.6 mm) in diameter — are
easily broken off when subjected to too much side thrust. A
See Figure 6.
TOO SLOW
TOO FAST
DEPTH
OF CUT
1ST.
2ND.
PASS
large enough cutter may not be broken off, but if the cut is too
deep a rough cut will result — and it may be very difficult to
guide and control the cutter as desired. For these reasons,
we recommend that you do not exceed 1/8 in. (3.2 mm) depth
of cut in a single pass, regardless of the cutter size or the
softness or condition of the workpiece. This will result in a
higher quality cut.
To make deeper cuts it is therefore necessary to make as
many successive passes as required, lowering the cutter
1/8 in. (3.2 mm) for each new pass. In order to save time,
do all the cutting necessary at one depth setting, before
lowering the cutter for the next pass. This will also assure
a uniform depth when the final pass is completed.
PASS
1ST. PASS
OF CUT
2ND. PASS
Fig. 6
WIDTH
Fig. 7
WARNING:
If desired depth of cut is greater than can be safely cut in
one pass, make cuts in two or more passes.
Page 10
Page 11
OPERATION
DIRECTION OF FEED AND THRUST
See Figures 8 and 9.
The trimmer motor and cutter revolve in a clockwise direction. This gives the tool a slight tendency to twist (in your
hands) in a counterclockwise direction, especially when the
motor starts.
Because of the extremely high speed of cutter rotation during
a “proper feeding” operation, there is very little kickback to
contend with under normal conditions. However, should the
cutter strike a knot, hard grain, foreign object, etc. that would
affect the normal progress of the cutting action, there will be
a slight kickback — sufficient to spoil the trueness of your cut
if you are not prepared. Such a kickback is always in the
direction opposite to the direction of cutter rotation.
To guard against such a kickback, plan your setup and
direction of feed so that you will always be thrusting the tool
— to hold it against whatever you are using to guide the cut
— in the same direction that the leading edge of the cutter is
moving. In short, the thrust should be in a direction that keeps
the sharp edges of the cutter continuously biting straight into
new (uncut) wood.
EXTENSION CORDS
The use of any extension cord will cause some loss of power.
To keep the loss to a minimum and to prevent tool
overheating, use an extension cord that is heavy enough to
carry the current the tool will draw.
A wire gage size (A.W.G.) of at least 16 is recommended for
an extension cord 100 feet or less in length. When working
outdoors, use an extension cord that is suitable for outdoor
use. The cord's jacket will be marked WA.
TRIM END
GRAINS FIRST
TRIMMER FEED
BIT
ROTATION
TRIMMER FEED
DIRECTION
GUIDE OUTSIDE
ROTATION
ROTATION
DIRECTION
DIRECTION
TRIMMER FEED
BIT
ROTATION
Fig. 8
THRUST
FEED
GUIDE
GUIDE INSIDE
GUIDE
CAUTION:
Keep extension cords away from any trimming area and
position the cord so that it will not get caught on lumber,
tools, etc., during trimming operation.
WARNING:
Check extension cords before each use. If damaged
replace immediately . Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
THRUST
FEED
Fig. 9
Page 11
Page 12
MAINTENANCE
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
BRUSH REPLACEMENT
See Figure 10.
Your trimmer has externally accessible brush assemblies
that should periodically be checked for wear. Proceed as
follows when replacement is required:
■ UNPLUG YOUR TRIMMER.
WARNING:
Failure to unplug your trimmer could result in accidental
starting causing serious injury.
■ Remove brush cap with a flat blade screwdriver. Brush
assembly is spring loaded and will pop out when you
remove brush cap.
■ Remove brush assembly (brush and spring).
■ Check for wear. If worn, always replace in pairs. DO
NOT replace one side without replacing the other
■ Reassemble using new brush assemblies. Make sure
curvature of brush matches curvature of motor and that
brush moves freely in brush tube.
■ Make sure brush cap is oriented correctly (straight) and
replace.
■ Tighten brush cap securely. DO NOT over torque.
PROPER CARE OF CUTTERS
Get faster more accurate cutting results by keeping cutters
clean and sharp. Remove all accumulated pitch and gum
from cutters after each use.
When sharpening cutters, sharpen only the inside of the
cutting edge. Never grind the outside diameter. Be sure
when sharpening the end of a cutter to grind the clearance
angle the same as originally ground.
PROPER CARE OF COLLET
From time to time, it also becomes necessary to clean your
collet and collet nut. To do so, simply remove collet nut from
collet and clean the dust and chips that have collected. Then
return collet nut to its original position.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
.
BRUSH CAP
BRUSH
ASSEMBLY
Fig. 10
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc. come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
When electric tools are used on fiberglass boats, sports cars,
wallboard, spackling compounds, or plaster, it has been
found that they are subject to accelerated wear and possible
premature failure, as the fiberglass chips and grindings are
highly abrasive to bearings, brushes, commutators, etc.
Consequently it is not recommended that this tool be used
for extended work on any fiberglass material, wallboard,
spackling compounds, or plaster. During any use on these
materials, it is extremely important that the tool is cleaned
frequently by blowing with an air jet.
WARNING:
Always wear safety goggles, or safety glasses with side
shields during power tool operation or when blowing dust.
If operation is dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
Page 12
Page 13
ACCESSORIES
HELPFUL HINTS
✓ Always clamp workpiece securely before trimming.
✓ A safe operator is one who thinks ahead.
✓ Always wear eye protection when trimming.
✓ Make setup adjustments carefully. Then double check.
Measure twice and cut once.
✓ Keep cutters clean and properly sharpened.
✓ Don’t let familiarity make you careless.
✓ Study all safety rules and do the job safely.
✓ NEVER place your hands in jeopardy.
✓ Make certain clamps can’t loosen while in use.
✓ Test difficult setups on scrap — Don’t waste lumber.
✓ Plan each operation before you begin.
✓ Provide for smoother operation by cleaning your
trimmer frequently. Shake trimmer or blow with an air
jet to remove sawdust buildup.
✓ THINK SAFETY BY THINKING AHEAD.
EDGE SHAPING WITH OPTIONAL TRIMMER GUIDE
Fig. 11
Standard accessories included with your laminate trimmer
are two wrenches. A subbase accessory with two handles is
also included.
The following is a list of optional accessories available for
your Laminate Trimmer:
Part No. Description
6072373 Trimmer Guide
4675208 Straight Trim Bit
6072063 Straight Guide
Fig. 12
Page 13
WARNING:
Avoid hand positions that may expose fingers to cutter
through open areas of trimmer base.
See Figure 12.
Page 14
R2
R2
R3
1
2
1/4
1/2
3/4
1
ACCESSORIES
TRIMMING WITH SUBBASE ACCESSORY
See Figures 13 and 16.
A subbase accessory is packed in the box with your trimmer.
If desired, the existing subbase can be removed and this
accessory attached.
It is convenient when routing 4 in. (101.6 mm), 5 in. (127 mm),
or 6 in. (152.4 mm) circular grooves. It can also be used
when routing grooves parallel to the edge of the workpiece.
The handles provided allow you to grasp and hold your
trimmer with two hands similar to grasping and holding a
router.
TO ATTACH SUBBASE ACCESSORY
See Figure 13.
■ Unplug your trimmer.
WARNING:
Failure to unplug your trimmer could result in accidental
starting causing serious injury.
LAMINATE
TRIMMER
HANDLE(S)
■ Turn your laminate trimmer upside down, remove the
four subbase screws and subbase.
■ Attach your subbase accessory using the same four
subbase screws.
■ Tighten subbase screws securely, but do not overtighten.
■ Turn your laminate trimmer upright and thread the
handles provided into the threaded holes in the subbase
accessory.
■ Tighten handles securely.
ROUTING GROOVES IN A CIRCLE
See Figure 14.
■ There are three holes marked R2", R2-1/2", and R3" on
the subbase accessory. Each number represents a radius and may be used when cutting circular grooves that
are 4 in. (101.6 mm), 5 in. (127 mm) or 6 in. (152.4 mm)
in diameter.
■ Select the radius for the desired circle, place a finishing
nail through the hole and securely tack it into your
workpiece. This will create a pivot axis for that size
radius.
■ Rout circular groove in a clockwise direction only. See
arrow shown in figure 14.
SUBBASE
ACCESSORY
SUBBASE
SCREW(S)
ROUT CIRCULAR GROOVE CLOCKWISE
R3
R2
1
2
Fig. 13
R2
1
FINISHING
NAIL
WORKPIECE
/4
1
/2
3
/4
1
Fig. 14
Page 14
Page 15
ACCESSORIES
ROUTING GROOVES PARALLEL TO AN EDGE
See Figures 13 and 14.
You can use the scale provided on the subbase accessory
to cut a straight parallel line up to 1 in. (25.4 mm) from the
edge of your workpiece.
■ The intersection of the horizontal and vertical lines at
the center of the subbase accessory indicates the center of your cutter. This is also the center of groove being
cut.
■ If you have purchased an optional straight guide, place
cutter at desired position on the workpiece and make
your cut from left to right as shown by the arrow in
figure 13.
■ In this case the thrust is from straight guide towards
the cutter or trimmer.
■ For grooves more than 1 in. (25.4 mm) from the edge
of workpiece, align the center of desired groove on
workpiece with centerline on subbase accessory. Then
measure from the centerline on subbase accessory to
the guiding portion of straight guide. Tighten knob on
the straight guide securely.
■ If you are using "C" clamps and a board to act as your
straight edge, place cutter at desired position on the
workpiece and make your cut from right to left as
shown by the arrow in figure 16.
■ Note: The board being used as a straight edge must
be 1/4 in. (6.4 mm) thick or less to prevent contact with
trimmer base. It must also be at least as long as the
workpiece in order to be a guide.
■ In this case the thrust is from your trimmer against the
straight edge.
■ As mentioned previously, do not make too heavy of a
cut in one pass. If a deep cut is required, make successive passes at increasing depths with each new
pass until you reach the desired groove depth.
ROUT GROOVE FROM LEFT TO RIGHT
R3
R2
1
R2
2
1
/4
1/2
3/4
1
ROUT GROOVE FROM RIGHT TO LEFT
Fig. 15
Page 15
R3
R2
1
R2
2
1/4
1/2
3/4
1
Fig. 16
Page 16
OPERAT OR'S MANUAL
LAMINATE TRIMMER - TR31-1
DOUBLE INSULATED
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to
provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your
nearest Ryobi Authorized Service Center. You can also check our web site at
www.ryobitools.com for a complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBER
• SERIAL NUMBER
TR31-1
983000-149
4-03
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson, SC 29625
Post Office Box 1207 Anderson, SC 29622-1207
Phone 1-800-525-2579
www.ryobitools.com
Loading...