OPERATOR’S MANUAL
CORDLESS DRILL-DRIVER
MODEL NOS. SA960 / SA120
MODEL SA960
20
MODEL SA120
20
This new drill has been engineered and manufactured to our Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
■■
■ Introduction .................................................................................................................................................................... 2
■■
■■
■ General Safety Rules..................................................................................................................................................3-4
■■
■■
■ Specific Safety Rules..................................................................................................................................................... 4
■■
■■
■ Important Safety Instructions for Charger...................................................................................................................... 5
■■
■■
■ Symbols ......................................................................................................................................................................... 6
■■
■■
■ Specifications................................................................................................................................................................. 7
■■
■■
■ Unpacking ...................................................................................................................................................................... 7
■■
■■
■ Applications....................................................................................................................................................................7
■■
■■
■ Features......................................................................................................................................................................8-9
■■
■■
■ Adjustments ............................................................................................................................................................10-12
■■
■■
■ Operation ................................................................................................................................................................ 13-16
■■
■■
■ Maintenance ........................................................................................................................................................... 17-18
■■
■■
■ Parts Ordering / Service .............................................................................................................................................. 18
■■
INTRODUCTION
The Cordless Drill-Driver has many features for making the use of this product more pleasant and enjoyable. Safety,
performance, and dependability have been given top priority in the design of this product making it easy to maintain
and operate.
WARNING:
Do not attempt to use this product until you thoroughly read and completely understand the operator’ s manual. Pa y
close attention to the safety rules, including Dangers, W arnings, and Cautions. If you use y our product properly and
only as intended, you will enjoy years of safe, reliable service.
Look for this symbol to point out important safety precautions. It
means attention!!! Your safety is involved.
WARNING:
The operation of any tool can result in foreign objects being thrown into your eyes, which can result in
severe e y e damage. Before beginning operation, always wear saf ety goggles or safety glasses with side
shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to
comply with ANSI Z87.1.
Page 2
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SA VE THESE INSTR UCTIONS
WORK AREA
■ Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. P o w er tools create sparks which may ignite the
dust or fumes.
■ Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
■ A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery .
■ Use battery operated tool only with specifically
designated battery pack. Use of any other batteries may
create a risk of fire.
■ Use battery only with charger listed.
MODEL BATTERY PACK CHARGER
SA960 1311146 1411140
SA120 1311148 1411141
■ Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords immediately. Damaged cords may create a fire.
PERSONAL SAFETY
■ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while oper-
ating power tools may result in serious personal injury.
■ Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
■ Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites accidents.
■ Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
■ Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
■ Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
TOOL USE AND CARE
■■
■ Use clamps or other practical way to secure and sup-
■■
port the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
■ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it is designed.
■ Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is dangerous and must be repaired.
■ Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool.
Such preventiv e safety measures reduce the risk of starting the tool accidentally.
■ Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
■ When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, ke ys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another . Shorting the
battery terminals together may cause sparks, burns, or a
fire.
■ Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
■ Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
■ Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool ma y create a risk of injury when used
on another tool.
■ Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following
this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.
Page 3
GENERAL SAFETY RULES
SERVICE
■ Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel may result in a risk of injury.
■ When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES
■■
■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
■■
hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.
ADDITIONAL RULES FOR SAFE OPERATION
■ Know your power tool. Read operator's manual care-
fully. Learn its applications and limitations, as well as
the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■ Always wear safety glasses with side shields. Everyday glasses have only impact resistant lenses. They are
NOT safety glasses. Following this rule will reduce the risk
of eye injury.
IMPORTANT RULES FOR BATTERY TOOLS
■ Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not
using your battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
■ WARNING: Batteries vent hydrogen gas and can ex-
plode in the presence of a source of ignition, such as a
pilot light. To reduce the risk of serious personal injury,
never use any cordless product in the presence of open
flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
■ Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
■ For best results, your battery tool should be charged in
a location where the temperature is more than 50°F but
less than 100°F. Do not store outside or in vehicles.
■ Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and
water, then neutralize with lemon juice or vinegar. If
liquid gets into your eyes, flush them with clean water
for at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of serious
personal injury.
Page 4
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
■ Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped battery
immediately. Failure to heed this warning can result in
serious personal injury.
■ Save these instructions. This manual contains important safety and operating instructions for charger.
■ Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
■ CAUTION: To reduce risk of injury, charge only nickel-
cadmium type rechargeable batteries. Other types of
batteries may burst causing personal injury and damage. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock, fire,
or serious personal injury.
■ Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
■ To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
■ Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. Following this rule will reduce the risk of serious
personal injury.
■■
■ Do not abuse cord. Never carry tool by cord or yank
■■
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges. Following this rule will reduce
the risk of electric shock or fire.
■ An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
■ Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
■ Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way;
take it to a qualified serviceman. Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.
■ Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock
or fire. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ To reduce the risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Disconnect charger from power supply when not in
use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
WARNING:
Some dust created by power sanding, sa wing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,
such as those dust masks that are specially designed
to filter out microscopic particles.
SA VE THESE INSTRUCTIONS
Page 5
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type or a characteristic of current
--- Direct Current Type or a characteristic of current
n
0
.../min Revolutions or Reciprocation Per Minute
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol Meaning
No Load Speed Rotational speed, at no load
Revolutions, strokes,
surface speed, orbits etc. per minute
Indicates danger, warning or caution.
Safety Alert Symbol It means attention!!! Your safety is
involved.
Always wear safety goggles or
Wear Eye Protection safety glasses with side shields when
operating this product.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
Page 6
SPECIFICATIONS
DRILL-DRIVER SA960 SA120
Chuck 3/8 in. (10 mm) Keyless 3/8 in. (10 mm) Keyless
Motor DC Motor 9.6 Volt DC Motor 12 Volt
Switch Variable Speed Variable Speed
No Load Speed 0 - 550 RPM 0 - 550 RPM
Clutch 24 Positions 24 Positions
Charger Input 120 V, 60 Hz, AC only 120 V, 60 Hz, AC only
Charge Rate 3-6 Hours 3-6 Hours
Torque Maximum 90 in.lb. Maximum 95 in.lb.
UNPACKING
INSTRUCTIONS
When unpacking the tool:
■ Carefully remove the tool and accessories from the box.
■ Make sure that all items listed in the packing list are in-
cluded.
■ Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
■ If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Cordless Drill
Charger
Battery Pack
28 Piece Bit Kit
Operator’s Man ual
Case
APPLICATIONS
WARNING:
If any parts are missing do not operate the tool until
the missing parts are replaced. F ailure to do so could
result in possible serious personal injury.
You may use the two speed drill for the purposes listed below:
■ Drilling in wood
■ Drilling in ceramics, plastics, fiberglass, and laminates
■ Drilling in both hard and soft metals
■ Using driving accessories, such as driving screws with screwdriver bits
■ Mixing paints
Page 7
FEATURES
KNOW Y OUR DRILL-DRIVER
See Figure 1.
Before using this tool, familiarize yourself with all operating
features and safety requirements. However, do not let
familiarity with the tool make you careless.
WARNING:
Exercise caution when using this tool. Careless actions, for even a fraction of a second, can result in
serious personal injury.
This new drill-driver is equipped with the following features.
KEYLESS CHUCK
The drill-driver has a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
SWITCH
The drill-driver has a conveniently located variable speed
switch.
SWITCH LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
FORW ARD/REVERSE SELECT OR
(DIRECTION OF ROTATION SELECTOR)
The drill-driver has a forward/re verse selector located abov e
the switch trigger.
BIT STORAGE
When not in use, bits provided with your drill-driver can be
placed in the storage area located on the top of the motor
housing.
LEVEL
To keep drill bit level during drilling operations, a level is
located on the top end of the motor housing.
Page 8
TORQUE
ADJUSTMENT
RING
FEATURES
MODEL SA960
LEVEL
BIT
STORAGE
AREA
20
DIRECTION OF
ROTATION
SELECTOR
KEYLESS
CHUCK
TORQUE
ADJUSTMENT
RING
SWITCH
TRIGGER
BATTERY
PACK
MODEL SA120
LEVEL
BIT
STORAGE
AREA
20
KEYLESS
CHUCK
DIRECTION OF
ROTATION
SELECTOR
SWITCH
TRIGGER
BATTERY
PACK
MAG TRAY™
Fig. 1
Page 9
ADJUSTMENTS
REVERSIBLE
See Figure 2.
This tool has the feature of being rev ersible. The direction of
rotation is controlled by a selector located above the switch
trigger. With the drill held in normal operating position, the
direction of rotation selector should be positioned to the left
of the switch for drilling. The drilling direction is reversed
when the selector is to the right of the switch. When the
selector is in center position, the switch trigger is locked.
CAUTION:
T o pre vent gear damage, alwa ys allow chuck to come
to a complete stop before changing the direction of
rotation.
To stop, release switch trigger and allow the chuck to
come to a complete stop.
KEYLESS CHUCK
See Figure 3.
A keyless chuck has been provided with your drill to allow for
easy installation and removal of bits. As the name implies,
you can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand. Rotate
the chuck body with your other hand. The arrows on the
chuck indicate which direction to rotate the chuck body in
order to GRIP (tighten) or RELEASE (unlock) the drill bit.
CENTER POSITION
(LOCK)
FORWARD
REVERSE
0
1
5
SWITCH
TRIGGER
RELEASE (UNLOCK)
CHUCK BODY
DIRECTION OF
ROTATION
SELECTOR
Fig. 2
W ARNING:
Do not hold the chuck body with one hand and use
the power of the drill to tighten chuck jaws on drill
bits. Chuck body could slip in y our hand or your hand
could slip and come in contact with rotating drill bit.
This could cause an accident resulting in serious personal injury.
GRIP
(TIGHTEN)
20
CHUCK
COLLAR
Fig. 3
Page 10
ADJUSTMENTS
INSTALLING BITS
See Figures 4 and 5.
■ Lock the switch trigger by placing the direction of rotation
selector in center position.
■ Open or close chuck jaws to a point where the opening
is slightly larger than the bit size you intend to use. Also,
raise the front of the drill slightly to keep the bit from
falling out of the chuck jaws.
■ Insert drill bit straight into chuck the full length of the
jaws.
See Figure 4.
■ Tighten the chuck jaws on the drill bit.
■ To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
■ Do not use a wrench to tighten or loosen the chuck
jaws.
See Figure 9.
WARNING:
Make sure to insert drill bit straight into chuck jaws.
Do not insert drill bit into chuck jaws at an angle then
tighten, as shown in Figure 5. This could cause drill
bit to be thrown from drill, resulting in possible serious personal injury or damage to the chuck.
CHUCK JAWS
DRILL BIT
RIGHT
CHUCK BODY
20
CHUCK COLLAR
Fig. 4
20
REMOVING BITS
See Figure 4.
■ Lock the switch trigger by placing the direction of
rotation selector in center position.
■ Loosen the chuck jaws from the drill bit
■ To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other
hand.
NOTE: Rotate chuck body in the direction of the arrow
marked UNLOCK to loosen chuck jaws.
■ Do not use a wrench to tighten or loosen the chuck
jaws.
■ Remove the drill bit from the chuck jaws.
NOTE: Rotate the chuck body in the direction of the arrow
marked GRIP to tighten the chuck jaws. DO NOT use a
wrench to tighten or loosen the chuck jaws.
See Figure 9.
.
WRONG
Fig. 5
Page 11
20
20
ADJUSTMENTS
ADJUSTABLE TORQUE CLUTCH
See Figure 6.
When using your drill-driver for various driving applications,
it becomes necessary to increase or decrease the torque in
order to help prevent the possibility of damaging scre w heads,
threads, workpiece, etc. In general, torque should correspond
to the intensity of the screw diameter. If the torque is too
high or the screws too small, the screws ma y be damaged or
broken.
The torque is adjusted by rotating the torque adjustment ring.
The torque is greater when the torque adjustment ring is set
on a higher setting. The torque is less when the torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and the
size of screw you are using.
TO ADJUST TORQUE
■ Identify the twenty four torque indicator settings located
on the front of the drill.
■ Rotate adjusting ring to the desired setting.
• 1 - 4 ..................For driving small screws.
• 5 - 8 ..................For driving screws into soft material.
• 9 - 12 ................For driving screws into soft and hard
materials.
• 13 - 16 ..............For driving screws in hard wood.
• 17 - 20 ..............For driving large screws.
• 21 - 24 ( )....For heavy drilling.
BIT STORAGE
See Figure 7.
When not in use, bits provided with your drill can be placed
in the storage area located on the top of your drill.
TO DECREASE
TORQUE
TORQUE
ADJUSTMENT
RING
TO INCREASE
TORQUE
Fig. 6
SCREWDRIVER BITS
BIT
STORAGE
AREA
Fig. 7
Page 12
OPERATION
WARNING:
Do not allow familiarity with the drill-driver to make
you careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
CHARGING YOUR DRILL-DRIVER
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it overnight prior to use.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by recharging) for them to fully charge.
TO CHARGE
See Figure 8.
■ Charge battery pack only with the charging assembly
provided.
■ Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only.
■ Connect charging assembly to power supply.
■ Place battery pack in charging assembly. Align raised
rib on battery pack with groove in charging assembly.
See Figure 9
■ Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charging
assembly. When properly connected, red light on charging assembly will turn on.
Note: During the two year warranty period, if the charge
indicator light (LED) fails to come on or goes out while
charging battery pack, return charging assembly and
battery pack to your nearest authorized service center
for repair or replacing.
■■
■ After normal usage, 3 hours or less of charging time is
■■
required to fully recharge battery pack. Note: If battery
pack is completely discharged, 6 hours or longer of
charging time is required to fully recharge battery
pack.
■ The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
■ DO NOT place charging assembly in an area of ex-
treme heat or cold. It will work best at normal room
temperature.
■ When battery pack has been charged, disconnect charging assembly from power supply and remove the battery pack. This practice will increase battery life.
.
BATTERY
PACK
CHARGING
ASSEMBLY
CHARGE
INDICATOR
LIGHT (LED)
Fig. 8
Page 13
OPERATION
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your drill-driver continuously, the batteries become hot. You should let the batteries cool down for approximately 30 minutes before attempting to recharge.
NOTE: This situation occurs when continuous use of your
drill-driver causes the batteries to become hot. It does not
occur under normal circumstances. Refer to “Charging Your
Drill-Driver” earlier in this manual, for normal recharging of
batteries. If the charger does not charge your batteries under
normal circumstances, return both the drill-driver and charger
to your nearest authorized service center for electrical check.
For more information on the battery recycling call
1-800-8 BATTERY.
TO INSTALL BATTERY PACK
■■
■ Place the direction of rotation selector in center posi-
■■
tion.
See Figure 9.
■■
■ Place the battery pack in your drill. Align raised rib on
■■
battery pack with groove in drill's battery port.
ure 10.
■■
■ Make sure the latches on each side of your battery pack
■■
snap in place and that battery pack is secured in drill
before beginning operation.
See Fig-
CENTER POSITION
(LOCK)
FORWARD
REVERSE
0
1
5
SWITCH
TRIGGER
20
DIRECTION OF
ROTATION
SELECTOR
Fig. 9
TO REMOVE BATTERY PACK
■■
■ Place the direction of rotation selector in center posi-
■■
tion.
See Figure 9.
■■
■ Locate latches on side of battery pack and depress both
■■
sides to release battery pack from your drill.
■■
■ Remove battery pack from your drill.
■■
See Figure 4.
CAUTION:
When placing battery pack in your drill, be sure raised
rib on battery pack aligns with groove in drill's battery
port and latches snap in place properly. Improper
assembly of battery pack can cause damage to internal components.
SWITCH
See Figure 9.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
SWITCH LOCK
See Figure 9.
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use. To lock the switch trigger, place the direction
of rotation selector in the center position.
BATTERY
PACK
DEPRESS
LATCHES TO
RELEASE
BATTERY PACK
BATTERY
PORT
LATCHES
Fig. 10
Page 14
OPERATION
2
0
15
VARIABLE SPEED
See Figure 9.
Your drill has a variable speed feature in the switch. The
switch delivers higher speed and torque with increased
trigger pressure. Speed is controlled by the amount of
switch trigger depression.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tool. F ailure to do so could
result in objects being thrown into your eyes, resulting in possible serious injury.
DRILLING
See Figure 11.
When drilling hard, smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
lower speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate your
drill at lower speed until the hole is started.
The material to be drilled should be secured in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
Fig. 11
WARNING:
Be prepared for binding or bit breakthrough. When
these situations occur, the drill has a tendency to grab
and kick opposite to the direction of rotation and could
cause loss of control when breaking through material. If you are not prepared, this loss of control can
result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
Page 15
OPERATION
LEVEL DRILLING
See Figure 12.
A convenient new feature provided with your drill is a level.
It is recessed in the motor housing on top of your drill. It can
be used to keep drill bit level during drilling operations.
MAG TRAY™ MODEL SA120
See Figure 13.
For convenience, your drill has a Mag Tray™ to place small
parts when doing a variety of tasks.
0
2
MODEL SA120
20
LEVEL
Fig. 12
MAG TRAY™
(SCREW HOLDER)
20
Fig. 13
Page 16
MAINTENANCE
20
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in
contact with plastic parts. They contain chemicals that
can damage, weaken or destroy plastic.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such
alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury .
MALLET
CHUCK JAWS
HEX KEY
KEYLESS CHUCK
20
Fig. 14
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc. that can
damage, weaken, or destroy plastic.
WARNING:
Always wear eye protection marked to comply with
ANSI Z87.1. F ailure to do so could result in dust, shavings, or loose particles being thrown into your eyes,
resulting in possible serious injury.
CHUCK REMOVAL
See Figures 14, 15, and 16.
The chuck must be removed in order to use some accessories. To remove:
■ Lock the switch trigger by placing the direction of
rotation selector in center position. See
■ Insert a 5/16 in. or larger hex key into the chuck of the
drill and tighten the chuck jaws securely.
■ Tap the hex key sharply with a mallet in a clockwise
direction.
the chuck for easy removal.
See Figure 14.
This will loosen the screw in
Figure 4.
Fig. 15
20
Page 17
Fig. 16
MAINTENANCE
■ Open the chuck jaws and remove the hex key. Remove
the chuck screw by turning it in a clockwise direction.
See Figure 15.
NOTE: The screw has left hand threads.
■ Insert the hex key in the chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the
spindle. It can now be unscrewed by hand.
16.
See Figure
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
To tighten, follow these steps:
■ Lock the switch trigger by placing the direction of
rotation selector in center position. See
■ Open the chuck jaws.
■ Insert the hex key into the chuck and tighten chuck
jaws securely. Tap the hex key sharply with a mallet in
a clockwise direction. This will tighten the chuck on the
spindle.
■ Open the chuck jaws and remove the hex key.
■ Tighten the chuck screw.
NOTE: The chuck screw has left hand threads.
See Figure 16.
Figure 3.
BATTERIES
The battery pack for your tool is equipped with nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are doing.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
■ Store and charge your batteries in a cool area.
Temperatures below 50°F or above 100°F will shorten
battery life.
■ Never store batteries in a discharged condition. Recharge
them immediately after they are discharged.
■ All batteries gradually lose their charge. The higher the
temperature the quicker they lose their charge. If you
store your tool for long periods of time without using it,
recharge the batteries every month or two. This practice
will prolong battery life.
BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING
WARNING:
Upon removal, cov er the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its components. Nick el-cadmium batteries must be recycled
or disposed of properly . Also , ne ver touch both terminals with metal objects and/or body parts as shor t
circuit may result. Keep away from children. Failure
to comply with these warnings could result in fire and/
or serious injury.
Y
C
C
L
E
RBRC
Cd
Ni
.
.
8
2
2
E
™
R
1
.
8
0
0
Consult your local waste authority for information regarding
available recycling and/or disposal options
To preserve natural resources, please
recycle or dispose of batteries properly.
This product contains nickel-cadmium
batteries. Local, state or federal laws may
7
3
prohibit disposal of nickel-cadmium
8
8
batteries in ordinary trash.
Page 18
NOTES
Page 19
OPERATOR’S MANUAL
CORDLESS DRILL-DRIVER
MODEL NOS. SA960 / SA120
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
Authorized Service Center. You can also check our web site at www.ryobitools.com for a
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBERS
• SERIAL NUMBER
SA960 / SA120
983000-333
6-03
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson SC 29625
Post Office Box 1207 Anderson SC 29622
Phone 1-800-525-2579
www.ryobitools.com
Loading...