Ryobi HP1802M, HP1442M User Manual

OPERATOR'S MANUAL

CORDLESS DRILL-DRIVER MODEL NOS. HP1442M / HP1802M

MODEL HP1442M

MODEL HP1802M

THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER.

Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

CAUTION: Carefully read through this entire operator’s manual before using your new cordless drill-driver.

Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless drill-driver properly and only for what it is intended, you will enjoy years of safe, reliable service.

Thank you again for buying Ryobi tools.

SAVE THIS MANUAL FOR FUTURE REFERENCE

TABLE OF CONTENTS

■ General Safety Rule ................................................................................................................................................ 2-3

■ Specific Safety Rules/Symbols ................................................................................................................................ 3-5

■ Features .................................................................................................................................................................. 6-7

■ Operation ............................................................................................................................................................... 8-14

■ Maintenance ............................................................................................................................................................. 15

■ Parts Ordering / Service ........................................................................................................................................... 16

GENERAL SAFETY RULES

Personal Safety

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS Work Area

■ Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

■ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which

may ignite the dust or fumes.

■ Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to

lose control.

Electrical Safety

■ Do not abuse the cord. Never use the cord to carry the charger. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords may create a fire.

■ A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that

may be suitable for one type of battery may create a risk of fire when used with another battery. Use battery only with charger listed.

MODEL BATTERY CHARGER HP1442M 1314702 1412001

HP1802M 1322401 / 1323303 1423701

■ Use battery operated tool only with specifically designated battery pack. Use of any other batteries

may create a risk of fire. Use only with battery pack listed.

■ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while

operating power tools may result in serious personal injury.

■ Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jew-

elry, or long hair can be caught in moving parts.

■ Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack.

Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on, invites accidents.

■ Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a

rotating part of the tool may result in personal injury.

■ Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better

control of the tool in unexpected situations. Do not use on a ladder or unstable support.

■ Use safety equipment. Always wear eye protection.

Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Page 2

GENERAL SAFETY RULES

Tool Use and Care

■ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable and may lead to loss of control.

■ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer

at the rate for which it is designed.

■ Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.

■ Disconnect battery pack from tool before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce risk of

starting the tool accidentally.

■ Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands

of untrained users.

■ When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

■ Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting

edges are less likely to bind and are easier to control.

■ Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by

poorly maintained tools.

■ Use only accessories that are recommended by the manufacturer for your model. Accessories that may

be suitable for one tool, may create a risk of injury when used on another tool.

Service

■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed

by unqualified personnel could result in a risk of injury.

■ When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or

failure to follow Maintenance Instructions may create a risk of shock or injury.

SPECIFIC SAFETY RULES AND/OR SYMBOLS

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Additional Rules For Safe Operation

■ Know your power tool. Read operator's manual care-

fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool.

Following this rule will reduce the risk of electric shock, fire, or serious injury.

■ Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. An

undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Important Rules for Battery Tools

■ Battery tools do not have to be plugged into an

electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.

■ Do not place battery tools or their batteries near fire

or heat. This will reduce the risk of explosion and

possibly injury.

WARNING:

Batteries vent hydrogen gas and can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemical. If exposed, flush with water immediately.

■ Do not charge battery tool in a damp or wet location.

Following this rule will reduce the risk of electric shock.

■ For best results, your battery tool should be charged in a location where the temperature is more than 50° F but less than 100°F. Do not store outside or in ve-

hicles.

■ Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk

of serious personal injury.

Page 3

SPECIFIC SAFETY RULES AND/OR SYMBOLS

W ARNING:

A damaged battery is subject to explosion. To avoid serious personal injury, properly dispose of a damaged battery.

Important Safety Instructions For Charger

■ Save these instructions. This manual contains im-

portant safety and operating instructions for charger.

Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

■ Before using battery charger, read all instructions

and cautionary markings in this manual, on battery charger, and product using battery charger. Follow-

ing this rule will reduce the risk of electric shock, fire, or serious personal injury.

■ To reduce risk of injury, charge only nickel-cadmium

and nickel metal hydride type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. Following this rule will

reduce the risk of electric shock, fire, or serious personal injury.

■ Do not expose charger to wet or damp conditions.

Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

■ Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following

this rule will reduce the risk of electric shock, fire, or serious personal injury.

■ To reduce risk of damage to charger body and cord,

pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk

of electric shock, fire, or serious personal injury.

■ Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to damage or stress. Following this rule will reduce the risk

of serious personal injury.

■ An extension cord should not be used unless absolutely necessary. Use of improper extension cord could

result in a risk of fire and electric shock. If extension cord must be used, make sure:

a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet) 25' 50' 100' Cord Size (AWG) 16 16 16 Note: AWG = American Wire Gage

■ Do not operate charger with a damaged cord or plug.

If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

■ Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Following this

rule will reduce the risk of electric shock, fire, or serious personal injury.

■ Do not disassemble charger; take it to a qualified

serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.

■ To reduce the risk of electric shock, unplug charger

from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.

■ Disconnect charger from power supply when not in use. Following this rule will reduce the risk of electric

shock, fire, or serious personal injury.

DANGER:

RISK OF ELECTRIC SHOCK. DO NOT TOUCH UNINSULATED PORTION OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.

■ Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk

of electric shock, fire, or serious personal injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Page 4

SYMBOLS

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type or a characteristic of current

--- Direct Current Type or a characteristic of current

.../min Revolutions or Reciprocation Per Minute Revolutions, strokes,

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

No Load Speed Rotational speed, at no load

surface speed, orbits etc. per minute

Safety Alert Symbol Indicates danger, warning or caution.

It means attention!!! Your safety is involved.

SYMBOL MEANING

SAFETY ALERT SYMBOL:

Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.

Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to

yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

SAVE THESE INSTRUCTIONS

Page 5

+ 11 hidden pages