Page 1
OPERATOR'S MANUAL
1/2 in. (13 mm) THREE SPEED
CORDLESS HAMMER DRILL
MODEL NO. HD1830
15
This new cordless hammer drill has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. When properly cared for, the drill-driver will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before
using this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 2
TABLE OF CONTENTS
■ Introduction ..................................................................................................................................................................... 2
■ General Safety Rules ................................................................................................................................................. 3-4
■ Specific Safety Rules ...................................................................................................................................................... 4
■ Important Safety Instructions for Charger ....................................................................................................................... 5
■ Symbols .......................................................................................................................................................................... 6
■ Specifications ................................................................................................................................................................. 7
■ Unpacking ....................................................................................................................................................................... 7
■ Applications .................................................................................................................................................................... 7
■ Features ..................................................................................................................................................................... 8-9
■ Adjustments ............................................................................................................................................................ 10-12
■ Operation ................................................................................................................................................................ 13-17
■ Maintenance ........................................................................................................................................................... 18-19
■ Parts Ordering / Service ............................................................................................................................................... 20
INTRODUCTION
This cordless hammer drill has many features for making
the use of this product more pleasant and enjoyable.
Safety, performance, and dependability have been given
top priority in the design of this product making it easy to
maintain and operate.
WARNING:
The operation of any drill can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles
or safety glasses with side shields and a full face shield when needed. We recommend Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always
wear eye protection which is marked to comply with ANSI Z87.1.
WARNING:
Do not attempt to use this product until you thoroughly
read and completely understand the operator’s manual.
Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use your product
properly and only as intended, you will enjoy years of
safe, reliable service.
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 2
Page 3
GENERAL SAFETY RULES
WARNING
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
■ Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
■ Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
■ Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords immediately. Damaged cords may create a fire.
■ A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery.
■ Use battery operated tool only with specifically
designated battery pack. Use of any other batteries may
create a risk of fire.
■ Use battery only with charger listed.
MODEL BATTERY CHARGER
HD1830 130255004 1423701
PERSONAL SAFETY
■ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while oper-
ating power tools may result in serious personal injury.
■ Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
■ Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites accidents.
■ Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
■ Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
■ Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
TOOL USE AND CARE
■ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
■ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it is designed.
■ Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is dangerous and must be repaired.
■ Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool.
Such preventive safety measures reduce risk of starting
the tool accidentally.
■ Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of
untrained users.
■ When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause sparks, burns, or a
fire.
■ Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
■ Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
■ Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool may create a risk of injury when used
on another tool.
■ Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool.
Page 3
Page 4
GENERAL SAFETY RULES
SERVICE
■ Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
■ Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring. Contact with a "live" wire will
make exposed metal parts of the tool "live" and shock
the operator.
ADDITIONAL RULES FOR SAFE OPERATION
■ Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well as
the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■ Always wear safety glasses with side shields. Everyday glasses have only impact resistant lenses. They are
NOT safety glasses.
IMPORTANT RULES FOR BATTERY TOOLS
■ Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not
using your battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Do not place battery tools or their batteries near fire or
heat. This will reduce the risk of explosion and possibly
injury.
■ When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
■ Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light. To
reduce the risk of serious personal injury, never use any
cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
■ Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
■ For best results, your battery tool should be charged in
a location where the temperature is more than 50°F but
less than 100°F. Do not store outside or in vehicles.
■ Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with
your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for at
least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious
personal injury.
Page 4
Page 5
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER
WARNING:
Read and understand all instructions. Failure to fol-
low all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
■ Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped battery
immediately. Failure to heed this warning can result in
serious personal injury.
■ Save these instructions. This manual contains important safety and operating instructions for charger.
■ Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
■ CAUTION: To reduce risk of injury, charge only nickel-
cadmium type rechargeable batteries. Other types of
batteries may burst causing personal injury and damage. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
■ Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
■ To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
■ Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. Following this rule will reduce the risk of serious
personal injury.
■ Do not abuse cord. Never carry tool by cord or yank
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges. Following this rule will reduce
the risk of electric shock or fire.
■ An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
■ Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
■ Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take
it to a qualified serviceman. Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.
■ Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock
or fire. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ To reduce the risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this risk.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
■ Disconnect charger from power supply when not in
use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
SAVE THESE INSTRUCTIONS
Page 5
Page 6
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type or a characteristic of current
--- Direct Current Type or a characteristic of current
n
0
.../min Revolutions or Reciprocation Per Minute
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol Meaning
No Load Speed Rotational speed, at no load
Revolutions, strokes,
surface speed, orbits etc. per minute
Indicates danger, warning or caution.
Safety Alert Symbol It means attention!!! Your safety is
involved.
Always wear safety goggles or
Wear Eye Protection safety glasses with side shields when
operating this product.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
Page 6
Page 7
SPECIFICATIONS
Chuck ............................................................................................................................................... 1/2 in. (13 mm) Keyless
Motor .................................................................................................................................................................... 18 Volt DC
Switch ........................................................................................................................................................... Variable Speed
Gear Train ................................................................................................................................................................ 3 Speed
No Load Speed ............................................................................................................................. 0-370/0-750/0-2,200/min.
Hammer Speed .................................................................................................................. 0-5,920/0-12,000/0-35,200 BPM
Clutch ................................................................................................................................................................. 24 Positions
Charger Input ..................................................................................................................................... 120 V, 60 Hz, AC only
Charge Rate................................................................................................................................................................ 1 Hour
Maximum Torque .................................................................................................................................................... 480 in.lb.
UNPACKING
INSTRUCTIONS
This Cordless Hammer Drill has been shipped completely
assembled.
■ Carefully remove the tool and the accessories from the
box.
■ Make sure that all items listed in the packing list are
included.
■ Inspect the tool carefully to be sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
■ If any parts are damaged or missing, please call 1-800525-2579 for assistance.
APPLICATIONS
PACKING LIST
Cordless Hammer Drill
2 batteries
Charger
2 Bits
Operator's Manual
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
WARNING:
This tool should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
You may use the cordless hammer drill for the purposes listed below:
Hammer drilling in concrete, brick, or other masonry.
Drilling in wood.
Drilling in ceramics, plastics, fiberglass, and laminates.
Drilling in both soft and hard metals.
Driving screws with screwdriver bits, using driving accessories.
Mixing paint.
Page 7
Page 8
FEATURES
KNOW YOUR HAMMER DRILL
See Figure 1.
Before using this product, familiarize yourself with all operating
features and safety requirements. However, do not let
familiarity with the tool make you careless.
KEYLESS CHUCK
This hammer drill has a heavy-duty keyless chuck that allows
you to hand tighten or release drill bit in the chuck jaws.
SWITCH
This hammer drill has a conveniently located variable speed
trigger switch.
SWITCH LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
THREE SPEED GEAR TRAIN
This hammer drill has a three-speed gear train. A slide switch
is located on top of the drill to select either LO (1), HI (2) or
SUPER-HI (3) speed.
FORWARD/REVERSE SELECTOR
(DIRECTION OF ROTATION SELECTOR)
The hammer drill has a forward/reverse selector located
above the switch trigger.
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
HAMMER MODE OPERATION
This tool features a hammer speed of 0-35,200 Blows Per
Minute (BPM) in SUPER-HI (3) speed. Blows Per Minute is
the number of impacts per minute when operating in Hammer
Mode.
AUXILIARY HANDLE ASSEMBLY
An auxiliary handle is installed on the hammer drill. For ease
of operation, you may use the handle with either the left hand
or the right hand.
DEPTH GAUGE ROD
A depth gauge rod is installed on the auxiliary handle
assembly to assist you in controlling the depth of drilled
holes.
BIT STORAGE
When not in use, bits provided with your drill-driver can be
placed in the storage area located on the top of the motor
housing.
Page 8
Page 9
DEPTH GAUGE
ROD
FEATURES
THREE SPEED
GEAR TRAIN (LO-HI-SUPER-HI)
AUXILIARY
HANDLE ASSEMBLY
KEYLESS
CHUCK
15
DIRECTION OF
ROTATION SELECTOR
TORQUE
ADJUSTING RING
SWITCH
TRIGGER
BIT
STORAGE AREA
BATTERY PACK
Fig. 1
Page 9
Page 10
WARNING:
ADJUSTMENTS
The hammer drill should never be connected to a
power supply when you are assembling parts, making
adjustments, cleaning, performing maintenance, or
when the tool is not in use. Disconnecting the tool will
prevent accidental starting that could cause serious
injury.
ADJUSTING THE AUXILIARY HANDLE
ASSEMBLY
See Figure 2.
Follow these steps to adjust the auxiliary handle assembly.
■ Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
■ Rotate the auxiliary handle assembly to the desired
location.
■ Tighten the auxiliary handle assembly securely by
turning the knob clockwise.
ADJUSTING THE DEPTH GAUGE ROD
See Figure 3.
Follow these steps to adjust the depth gauge rod.
■ Lock the trigger switch by placing the rotation
selector in the center position.
■ Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
■ Adjust the depth gauge rod so that the drill bit
extends beyond the end of the rod to the required
drilling depth.
■ Tighten the auxiliary handle assembly by turning the
knob clockwise.
AUXILIARY
HANDLE ASSEMBLY
TIGHTEN
TO DECREASE
DRILLING DEPTH
DRILLING
DEPTH
TO
TO INCREASE
DRILLING DEPTH
5
1
15
TO
LOOSEN
Fig. 2
DEPTH
GAUGE ROD
Page 10
DRILL BIT
AUXILIARY
HANDLEASSEMBLY
Fig. 3
Page 11
ADJUSTMENTS
ADJUSTING THE TORQUE
See Figure 4.
The hammer drill is equipped with an adjustable torque
clutch for driving different types of screws into different
materials. Adjust the torque as necessary. We recommend
that you use carbide-tipped bits and select hammer mode
when drilling in hard materials such as brick, tile, concrete,
etc.
Follow these steps to adjust the torque.
■ Identify the torque indicator settings located on the
front of the hammer drill.
■ Rotate the adjusting ring to the desired setting.
• 1 - 4 For driving small screws.
• 5 - 8 For driving screws into soft material.
• 9 - 12 For driving screws into soft and hard
materials.
• 13 - 16 For driving screws in hard wood.
• 17 - 20 For driving large screws.
TO DECREASE
TORQUE
TO INCREASE
TORQUE
HAMMER MODE
DRILLING MODE
5
1
TORQUE
ADJUSTING RING
Fig. 4
• 21 - For heavy drilling.
• For hammer drilling.
CAUTION:
The hammer drill is not designed for reverse hammering. Failure to obey this caution may result in property
damage.
Page 11
Page 12
ADJUSTMENTS
CHANGING THE BIT ROTATION
See Figure 5.
The direction of the chuck is controlled by the rotation
selector located above the trigger switch.
Follow these steps to change the bit rotation.
For forward rotation
■
left.
■
For reverse rotation
right.
Note: The hammer drill will not run unless the
selector is pushed fully to the left or right.
: Move the rotation selector to the
: Move the rotation selector to the
INSERTING BITS
See Figure 6.
Follow these steps to insert bits.
■ Lock the trigger switch by placing the rotation selector
in the center position.
■ Open or close chuck jaws to a point where the opening
is slightly larger than the bit size you intend to use. Also,
raise the front of the drill slightly to keep the bit from
falling out of the chuck jaws.
■ Insert drill bit straight into chuck the full length of the
jaws as shown in figure 6.
FORWARD / REVERSE
SELECTOR
FORWARD
CHUCK JAWS
(Release)
UNLOCK
REVERSE
Fig. 5
CHUCK COLLAR
WARNING:
Do not insert a drill bit into the chuck jaws and tighten as
shown in Figure 7. This could cause the drill bit to be
thrown from the drill resulting possible serious injury or
damage to the chuck.
■ Tighten the chuck jaws on the drill bit. To tighten, grasp
and hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
Note: Rotate the chuck body in the direction of the arrow
marked GRIP to tighten the chuck jaws.
■ Do not use a wrench to tighten or loosen the chuck
jaws.
REMOVING BITS
See Figure 6.
Follow these steps to remove bits.
■ Lock the trigger switch by placing the rotation selector
in the center position.
■ Loosen the chuck jaws from drill bit
■ To loosen: grasp and hold the collar of the chuck with one
hand, while rotating chuck body with your other hand.
Note: Rotate chuck body in the direction of the arrow
marked RELEASE to loosen chuck jaws.
■ DO NOT use a wrench to tighten or loosen the chuck
jaws.
■ Remove drill bit from chuck jaws.
.
DRILL BIT
LOCK
(Tighten)
RIGHT
WRONG
15
CHUCK BODY
Fig. 6
15
Fig. 7
Page 12
Page 13
OPERATION
WARNING:
Exercise caution when using this tool. Careless actions,
for even a fraction of a second, can result in serious
personal injury.
CHARGING YOUR DRILL-DRIVER
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by recharging) for them to fully charge.
CHARGER
BATTERY
PACK
TO CHARGE
■ Charge battery pack only with the charger provided.
■ Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
■ Connect charger to power supply.
■ Place battery pack in charger.
raised rib on battery pack with groove in charger.
■ Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
When properly connected, red light will turn on.
■ Normally, the yellow and green lights on the charger
will come on. This indicates charger is in control charge
mode and should switch to fast charge mode within 5
minutes. When charger is in fast charge mode the red
light will come on. If after a period of 15 minutes the
yellow and green lights remain on, remove the battery
pack, wait 1 minute and re-insert battery pack in charger.
If the yellow and green lights continue to remain on an
additional 15 minutes, the battery pack is damaged
and will not accept charge.
■ When your battery pack becomes fully charged, the
red light will turn off and the green light will turn on.
■ After normal usage, 1 hour of charge time is required to
be fully charged. A minimum charge time of 1 to 1-1/2
hours is required to recharge a completely discharged
tool.
■ The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
■ DO NOT place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
See Figure 8.
Align
GREEN LIGHT "ON"
INDICATES FULLY
CHARGED
YELLOW AND GREEN LIGHTS "ON"
INDICATES CONTROL CHARGE OR
POSSIBLE FAULTY BATTERY
Fig. 8
CHARGER
RED LIGHT "ON"
INDICATES FAST
CHARGING MODE
Fig. 9
LED FUNCTION OF CHARGER
See Figure 9.
LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK:
1. Red LED lighted = Fast Charging Mode
2. Green LED lighted = Fully Charged Battery Pack
3. Yellow and Green LED Lighted = Control Charge or Defective Battery Pack.
Page 13
Page 14
OPERATION
TURNING ON/OFF THE HAMMER DRILL
See Figure 10.
Follow these steps to turn on/off the hammer drill.
■
Turn on the hammer drill
■
Turn off the hammer drill
VARIABLE SPEED
See Figure 10.
Your drill has a variable speed feature in the switch. The
switch delivers higher speed and torque with increased
trigger pressure. Speed is controlled by the amount of
switch trigger depression.
SWITCH LOCK
See Figure 10.
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use. To lock the switch trigger, place the direction
of rotation selector in the center position.
REVERSIBLE
See Figure 10.
This tool is reversible. The direction of rotation is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch for
drilling. The drilling direction is reversed when the selector is
to the right of the switch. When the selector is in center
position, the switch trigger is locked.
: Depress the trigger switch.
: Release the trigger switch.
5
1
SWITCH TRIGGER
DIRECTION OF
ROTATION SELECTOR
Fig. 10
CAUTION:
To prevent gear damage, always allow chuck to come to
a complete stop before changing the speed or the
direction of rotation.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
WARNING:
Battery tools are always in operating condition. Therefore,
switch should always be locked when not in use or when
carrying at your side.
Page 14
Page 15
OPERATION
THREE SPEED GEAR TRAIN
See Figure 11.
The hammer drill has a three-speed gear train that provides
a super-high speed of approximately 2,200/min, a high
speed of approximately 750/min. and a low speed of
approximately 370/min (stated speeds are with the trigger
switch in the “Full-on” position).
Follow these steps to adjust the speed.
■
For super high speed
switch to “3.”
■
For high speed
to “2.”
■
For low speed
to “1.”
Note: If you have difficulty changing from one gear
range to the other, turn the chuck by hand until the
gears engage.
: Slide the three-speed gear train switch
: Slide the three-speed gear train
: Slide the three-speed gear train switch
CAUTION:
To prevent gear damage, always allow chuck to come to
a complete stop before changing the speed or the
direction of rotation.
SUPER-HI
SPEED
32
CHUCK JAWS
THREE-SPEED
GEAR TRAIN (LO-HI-SUPER-HI)
HI
SPEED
(Release)
UNLOCK
CHUCK COLLAR
LO
SPEED
1
Fig. 11
KEYLESS CHUCK
See Figure 12.
A keyless chuck has been provided with your drill to allow for
easy installation and removal of bits. As the name implies,
you can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand. Rotate
the chuck body with your other hand. The arrows on the
chuck indicate which direction to rotate the chuck body in
order to GRIP (tighten) or RELEASE (unlock) the drill bit.
WARNING:
Do not hold the chuck body with one hand and use the
power of the drill to tighten chuck jaws on drill bits. Chuck
body could slip in your hand or your hand could slip and
come in contact with rotating drill bit. This could cause
an accident resulting in serious personal injury.
DRILL BIT
LOCK
(Tighten)
CHUCK BODY
5
1
Fig.12
Page 15
Page 16
OPERATION
TO INSTALL BATTERY PACK
■ Place the direction of rotation selector in center position.
See Figure 10.
■ Place the battery pack in your drill. Align raised rib on
battery pack with groove in drill's battery port.
See Figure 13.
■ Make sure the latches on each side of your battery pack
snap in place and that battery pack is secured in drill
before beginning operation.
TO REMOVE BATTERY PACK
■ Place the direction of rotation selector in center position.
See Figure 10.
■ Locate latches on side of battery pack and depress both
sides to release battery pack from your drill.
See Figure 13.
■ Remove battery pack from your drill.
CAUTION:
When placing battery pack in your drill, be sure raised
rib on battery pack aligns with groove in drill's battery
port and latches snap in place properly. Improper
assembly of battery pack can cause damage to internal
components.
BATTERY PACK
DEPRESS LATCHES TO
RELEASE BATTERY PACK
BATTERY PORT
LATCHES
Fig. 13
BIT STORAGE
See Figure 14.
When not in use, the bit provided with this drill can be placed
in the storage area located on the base of the drill.
ELECTRIC BRAKE
This drill has an electric brake. When the trigger switch is
released, the chuck stops turning. When the brake is
functioning properly, sparks will be visible through the vent
slots on the housing. This is normal and is the action of the
brake.
BIT
STORAGE AREA
SCREWDRIVER
BIT
Fig. 14
Page 16
Page 17
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating tool. Failure to do so could result
in dust, shavings, or loose particles being thrown into
your eyes, resulting in possible serious injury.
DRILLING
See Figure 15.
The material to be drilled should be secured in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
We recommend that you select normal drill mode when
drilling with twist drills, hole saws, etc., in soft material.
WARNING:
Do not force tool. Forcing tool can result in jamming and
loss of balance or footing, which could result in personal
injury.
When drilling hard, smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
lower speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate your
drill at lower speed until the hole is started.
For drilling in wood, begin drilling at LO (1) speed, gradually increasing to full power. Occasionally clear chips from
the bit to prevent overheating. Low speed bits should be
used when drilling larger holes.
When drilling metals other than brass and cast iron, use a
light oil on the drill bit to keep it from overheating. The oil will
prolong the life of the bit and increase the drilling action.
Begin drilling at LO (1) speed, gradually increasing to higher
speeds. When drilling larger holes in steel, it may be helpful
to first drill a smaller pilot hole.
We recommend that you use carbide-tipped bits and select
hammer mode when drilling in hard materials such as brick,
tile, concrete, etc.
This tool is packed with two double-ended screwdriver bits.
For driving screws, select the desired speed and torque
settings using the speed selector and torque adjustment
ring. Insert the screwdriver bits as you would a drill bit, as
shown in figure 6. You may need to drive a few practice
screws in the type of material you will be working with.
For using the hammer drill feature, rotate the torque
adjustment ring, as shown in figure 4, so that the hammer
symbol is aligned with the arrow. Using the auxiliary handle
will provide better control and prevent forcing the tool.
Fig. 15
■ Hold the drill at a right angle as shown in figure 15. Do not
force or apply side pressure to elongate the hole.
■ If the hammer speed decreases while drilling deep holes,
it may be necessary to lift up partially on the tool to clear
debris from the hole.
■ If there is excessive dust while using the hammer feature,
do not add water to the hole. This can cause clogging and
binding of the bit.
■ If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
WARNING:
Be prepared for binding or bit breakthrough. When these
situations occur, the drill has a tendency to grab and kick
opposite to the direction of rotation, and could cause loss
of control when breaking through material. If you are not
prepared, this loss of control can result in possible serious
injury.
Maximum Recommended Capacities
SPEED 1 SPEED 2 SPEED 3
Bits, Metal Drilling 1/2" 1/4" 1/4"
Wood, Flat Boring 1-1/2" 5/8" 3/8"
Bits, Masonry Drilling - 1/4" 1/4"
Page 17
Page 18
MAINTENANCE
REMOVING THE CHUCK
See Figures 16, 17, and 18.
Follow these steps to remove the chuck.
■ Lock the trigger switch by placing the rotation selector
in the center position.
■ Insert a 5/16 inch or larger hex key wrench into the
chuck of the drill and tighten the chuck jaws securely.
■ Tap the hex key wrench sharply with a mallet in a
clockwise direction. This will loosen the screw in the
chuck for easy removal.
■ Open the chuck jaws and remove the hex key wrench.
■ Remove the chuck screw by turning it in a clockwise
direction.
Note: The screw has left hand threads.
■ Insert the hex key wrench in the chuck and tighten the
chuck jaws securely.
■ Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now
be unscrewed by hand.
MALLET
CHUCK JAWS
15
HEX KEY
KEYLESS CHUCK
Fig. 16
SCREWDRIVER
TIGHTENING THE CHUCK
The chuck may become loose on the spindle and begin to
shake when using the drill. Also, the chuck screw may
become loose causing the chuck jaws to bind and prevent
them from closing.
Follow these steps to tighten the chuck.
■ Lock the trigger switch by placing the rotation selector
in center position.
■ Open the chuck jaws.
■ Insert the hex key wrench into the chuck and tighten
the chuck jaws securely.
■ Tap the hex key wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
■ Open the chuck jaws and remove the hex key wrench.
■ Tighten the chuck screw.
Note: The chuck screw has left hand threads.
5
1
15
Fig. 17
Fig. 18
Page 18
Page 19
WARNING:
MAINTENANCE
DO NOT ABUSE POWER TOOLS. Abusive practices can
damage the tool, as well as the workpiece.
When servicing use only identical Ryobi replacement
parts. Use of any other parts can create a hazard or cause
product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
a clean cloth to remove dirt, oil, grease, etc.
CAUTION:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that may
damage, weaken, or destroy plastics.
BATTERIES
Your drill is equipped with Nickel-Cadmium rechargeable
batteries. Length of service from each charging will depend
on the type of work you are doing.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. DO NOT disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in serious burn.
To obtain the longest possible battery life, we suggest the
following:
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
CAUTION:
Any repairs requiring disassembly should only be
performed by a Ryobi Authorized Service Center. For
the repair center nearest you, call 1-800-525-2579.
■ Storing and charging your batteries in temperatures above
100°F or below 50°F will shorten battery life.
■ Never store batteries in a discharged condition. Wait for
battery to cool and charge immediately.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your tool for long periods of time without using it,
recharge the batteries every month or two. This practice
will prolong battery life.
DISPOSAL OF THE EXHAUSTED BATTERY
To preserve natural resources, please
recycle or dispose of properly.
This product contains nickel-cadmium
battery. Must be disposed of properly. Local,
state, or federal laws may prohibit disposal
of Nickel-Cadmium batteries in ordinary
trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
For more information on battery recycling call 1-800-
8BATTERY.
WARNING:
Do not attempt to disassemble the battery pack. Fire or
injury can result.
Page 19
BATTERY PACK PREPARATION FOR RECYCLING
WARNING:
Upon removal, cover the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its
components. Also, never touch both terminals with metal
objects and/or body parts, as short circuit can result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
Page 20
OPERATOR'S MANUAL
1/2 in. (13 mm) THREE SPEED
CORDLESS HAMMER DRILL
MODEL NO. HD1830
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
Authorized Service Center. You can also check our web site at www.ryobitools.com for a
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
HD1830
Phone 1-800-525-2579
www.ryobitools.com
983000-339
4-04
Loading...