Page 1
OPERATOR'S MANUAL
COMPACT FINISHING SANDER
5-1/2 in. (140 mm)
CFS1501
This new compact finishing sander has been engineered and manufactured to Ryobi’s high standard for dependability, ease
of operation, and operator safety. When properly cared for, the sander will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before
using this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 2
TABLE OF CONTENTS
■ Introduction ..................................................................................................................................................................... 2
■ General Safety Rules ................................................................................................................................................. 3-4
■ Specific Safety Rules ...................................................................................................................................................... 4
■ Symbols .......................................................................................................................................................................... 5
■ Electrical .........................................................................................................................................................................6
■ Features ......................................................................................................................................................................... 7
■ Unpacking ....................................................................................................................................................................... 8
■ Assembly .................................................................................................................................................................... 8-9
■ Operation ................................................................................................................................................................ 10-12
■ Maintenance .................................................................................................................................................................13
■ Parts Ordering / Service ............................................................................................................................................... 14
INTRODUCTION
This compact finishing sander has many features for making
the use of this product more pleasant and enjoyable. Safety,
performance, and dependability have been given top priority
in the design of this product making it easy to maintain and
operate.
WARNING:
WARNING:
Do not attempt to use this product until you thoroughly
read and completely understand the operator’s manual.
Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use your product
properly and only as intended, you will enjoy years of
safe, reliable service.
The operation of any tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning operation, always wear safety goggles or safety
glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye
protection which is marked to comply with ANSI Z87.1.
Look for this symbol to point out important safety precautions. It
means attention!!! Your safety is involved.
Page 2
Page 3
GENERAL SAFETY RULES
WARNING
Read and understand all instructions. Failure to fol-
low all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
■ Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■ Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
■ Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
■ Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation eliminates the need for the
three-wire grounded power cord and grounded power
supply system.
■ Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is
an increased risk of electric shock if your body is grounded.
■ Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
■ Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
■ When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords are
rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
■ Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while oper-
ating power tools may result in serious personal injury.
■ Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jew-
elry, or long hair can be caught in moving parts.
■ Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites
accidents.
■ Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
■ Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
■ Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
■ Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
■ Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
■ Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
■ Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it is designed.
■ Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is dangerous and must be repaired.
■ Disconnect the plug from power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
■ Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
■ Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
■ Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
■ Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
■ Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Following
this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.
Page 3
Page 4
GENERAL SAFETY RULES
SERVICE
■ Tool service must be performed only by qualified repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting
tool “live” and shock the operator.
ADDITIONAL SAFETY RULES
■ Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■ Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk of
serious personal injury.
■ Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
■ Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule
will reduce the risk of serious personal injury.
■ Inspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
■ Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service center. Following
this rule will reduce the risk of shock, fire, or serious injury.
■ Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges. Following
this rule will reduce the risk of electric shock or fire.
■ When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock
or injury.
■ Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 50 feet or less in
length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An un-
dersized cord will cause a drop in line voltage resulting in
loss of power and overheating.
■ Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
■ Drugs, alcohol, medication. Do not operate tool while
under the influence of drugs, alcohol, or any medication. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■ Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
SAVE THESE INSTRUCTIONS
Page 4
Page 5
SYMBOLS
Important: Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
VVolts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
WWatt Power
min Minutes Time
Alternating Current Type of current
---
n
0
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
Direct Current Type or a characteristic of current
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
Safety Alert Precautions that involve your safety
The manual contains special messages to bring attention to
Read The Operator’s Manual
Eye Protection
Wet Conditions Alert Do not expose to rain or use in damp locations.
potential safety concerns and machine damage as well as
helpful operating and servicing information. Please read all
the information carefully to avoid injury and machine damage.
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations
with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any
danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
Note: Advises you of additional information concerning the operation or maintenance of the equipment.
Page 5
Page 6
ELECTRICAL
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting
insulation. Double insulated tools do not need to be grounded.
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal insulation. Observe all normal safety precautions to avoid electrical shock.
Important: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory
replacement parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from a
power source, be sure to use an extension cord that has the
capacity to handle the current the tool will draw. An undersized
cord will cause a drop in line voltage, resulting in overheating
and loss of power. Use the chart to determine the minimum
wire size required in an extension cord. Only round jacketed
cords listed by Underwriter’s Laboratories (UL) should be
used.
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is designated
with "WA" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating
(on tool faceplate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 —
**Used on 12 gage - 20 amp circuit.
WARNING:
Keep the extension cord clear of the working area. Position the cord so that it will not become entangled in the
rotating foam pad or caught on lumber, tools or other
obstructions while you are working with a power tool.
Failure to do so can result in serious personal injury.
Page 6
WARNING:
Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
Page 7
FEATURES
SPECIFICATIONS
Sanding Pad Length ................................................................................................................................. 5-1/2 in. (140 mm)
No Load Speed .................................................................................................................................................... 12,000/min.
Cord ................................................................................................................................................................. 10 ft. (3.05 m)
Orbit Diameter........................................................................................................................................... 1/16 in. (1.59 mm)
Input ..................................................................................................................................120 Volts, 60 Hz, AC only, 1 Amp
Weight ............................................................................................................................................................2.6 lbs. (1.2 kg)
KNOW YOUR COMPACT FINISHING SANDER
See Figure 1.
Before using this product, familiarize yourself with all operating
features and safety requirements. However, do not let
familiarity with the tool make you careless.
SWITCH
This tool is equipped with a simple switch control located
near the front of the motor housing.
QUICK CHANGE HOOK AND LOOP PAD
The hook and loop design allows for quick change of sanding sheets and scrubbing pads. It also enables you to easily
clean and reuse them.
TRI-FLEX PAD DESIGN
The top two-thirds of each sanding pad is a detachable triangle that can be rotated to extend pad life and promote
even wear.
CIRCULAR SANDING ACTION
The oscillating action of your sander produces very quick,
small circular motion of the sanding pad. The motion is ideal
for producing a fine finished grain or, when using the scrubbing pad, removing light rust, paint and other build up from
the work surface.
DUST COLLECTION BAG
The dust bag attaches to the sander and keeps dust to a
minimum.
PAPER PUNCH
The paper punch template punches sandpaper for proper fit
and alignment.
Page 7
Fig. 1
Page 8
UNPACKING
INSTRUCTIONS
When unpacking the sander:
■ Carefully remove the tool and accessories from the box.
■ Make sure that all items listed in the packing list are
included.
■ Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
■ If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
If any parts are missing do not operate your tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
ASSEMBLY
WARNING:
The tool should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
SANDING DISC SELECTION
Selecting the correct size grit and type sanding disc is an
extremely important step in achieving a high quality sanded
finish. Aluminum oxide, silicon carbide, and other synthetic
abrasives are best for power sanding. Natural abrasives, such
as flint and garnet are too soft for economical use in power
sanding.
In general, coarse grit will remove the most material and finer
grit will produce the best finish in all sanding operations. The
condition of the surface to be sanded will determine which
grit will do the job. If the surface is rough, start with a coarse
grit and sand until the surface is uniform. Medium grit may
then be used to remove scratches left by the coarser grit
and finer grit used for finishing of the surface. Always continue sanding with each grit until surface is uniform.
Sheet/Pad Recommended Use
Heavy scrubbing pad Paint and rust removal
Light scrubbing pad Light scrubbing and cleaning
60-grit sanding sheet Coarse sanding
120-grit sanding sheet Light sanding
240-grit sanding sheet Finish sanding
PACKING LIST
5-1/2 in. (140 mm) Compact Finishing Sander
60-grit Sanding Pad (2)
120-grit Sanding Pad (3)
240-grit Sanding Pad (2)
Heavy-duty Scrubbing Pad (Red)
Light Scrubbing Pad (White)
Polishing Pad (Gray)
Dust Collection Bag
Pad Punch
Carrying Case
Operator's Manual
ATTACHING HOOK AND LOOP SANDING
DISCS
See Figure 2.
■ Unplug the sander.
■ Align holes in hook and loop type sanding disc with holes
in pad, then carefully press fuzzy side of sanding disc
against pad as tightly as possible.
Note: Hook and loop type sanding discs can be reused
for the life of the sanding abrasive. It is recommended
that you keep the sanding disc backing pad clean to provide for best adhesion. Clean occasionally by brushing
lightly with a small brush.
Fig. 2
Page 8
Page 9
ASSEMBLY
WARNING:
The sander should never be connected to a power supply when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
ATTACHING THE DUST BAG
See Figure 3.
The dust bag provides a dust collection system for the sander.
Sanding dust is drawn up through the holes of the sanding
disc and collected in the dust bag during sanding.
Follow these steps to attach the dust bag.
■ Unplug the sander.
■ Using a slight twisting motion as shown in figure 3, firmly
slide dust bag assembly in blower exhaust on sander.
Fig. 3
Page 9
Page 10
OPERATION
WARNING:
Exercise caution when using this tool. Careless actions,
for even a fraction of a second, can result in serious
personal injury.
APPLICATIONS
You may use the sander for the purposes listed below:
■ Sanding on wood surfaces.
■ Removing rust from and sanding steel surfaces.
■ Polishing and scrubbing porcelain and metal.
CAUTION:
Keep the cord away from the sanding pad and position
the cord so that it will not be caught on lumber, tools, or
other objects during sanding.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating this tool. Failure to do so could
result in dust, shavings, or loose particles being thrown
into your eyes, resulting in possible serious injury.
OPERATING THE SANDER
See Figure 5.
Follow these steps to operate the sander.
■ Secure the workpiece to prevent it from moving under
the sander.
WARNING:
Unsecured workpieces could be thrown towards the operator, causing injury.
WARNING:
Keep your head away from the sander and the sanding
area. Your hair could be drawn into the sander causing
serious injury.
■ Place the sander on the workpiece so that all of the sanding disc surface is in contact with the workpiece.
CAUTION:
To avoid damaging the motor from overheating, be careful not to let your hand cover the air vents.
TURNING THE SANDER ON/OFF
See Figure 4.
Follow these steps to turn the sander ON/OFF.
■ Turn on the sander: Push the ON/OFF switch to the left.
■ Turn off the sander: Push the ON/OFF switch to the right.
■ Turn on the sander and move it slowly over the
workpiece.
Hold the sander in front and away from you, keeping it clear
of the workpiece. Start sander and let the motor build to its
maximum speed, then gradually lower the sander onto the
workpiece. Move the sander slowly across the workpiece
using small circular motions.
See Figure 5.
Fig. 4
Fig. 5
Page 10
Page 11
OPERATION
Do not force. The weight of the unit supplies adequate pres-
sure, so let the sanding disc and sander do the work. Applying additional pressure only slows the motor, rapidly wears
sanding disc and greatly reduces sander speed. Excessive
pressure will overload the motor causing possible damage
from motor overheating and can result in inferior work. Any
finish or resin on wood may soften from the frictional heat.
Do not allow sanding on one spot too long as the sander’s
rapid action may remove too much material, making the surface uneven.
Extended periods of sanding may tend to overheat the motor. If this occurs, turn sander off and wait until sanding disc
comes to a complete stop, then remove it from workpiece.
Remove your hand from vent area, remove sanding disc,
then with your hand removed from vent area, turn sander on
and run it free without a load to cool motor.
For detail sanding such as corners and crevices, use the tip
of the sanding pad with small back and forth motions, as
shown in figure 6.
EMPTYING THE DUST BAG
See Figure 7.
For more efficient operation, empty the dust bag when it is
no more than half full. This will permit the air to flow through
the bag better. Always empty and clean the dust bag thoroughly upon completion of a sanding operation and before
placing the sander in storage.
WARNING:
Collected sanding dust from sanding surface coatings
such as polyurethanes, linseed oil, etc. can self-ignite in
your sander dust bag or elsewhere and cause fire. To
reduce the risk of fire always empty your dust bag frequently (10-15 minutes) while sanding and never store or
leave a sander without totally emptying its dust bag. Also
follow the recommendations of the coatings manufacturers.
Follow these steps to empty the dust bag:
■ Unplug the sander.
WARNING:
Fig. 6
Failure to unplug the tool could result in accidental starting causing possible serious injury.
■ Remove the dust bag from the sander.
■ Shake out the dust.
■ Reattach the dust bag to the sander.
For a more thorough cleaning of the dust bag, remove dust
bag from frame, as shown in figure 7, and shake out dust.
Replace dust bag over frame then install dust bag assembly on sander.
Page 11
Fig. 7
Page 12
OPERATION
CHANGING THE SANDING SHEETS
See Figure 8.
The sander is packed with sanding sheets and pads designed
for a variety of uses. To change sheets, simply pull the used
sheet off the base and attach the desired sheet by pressing
the sheet or pad onto the base of the sander.
Fig. 9
Fig. 10
Page 12
Page 13
MAINTENANCE
WARNING:
The tool should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause
product damage.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean cloths
to remove dirt, carbon dust, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
CLEANING THE SCRUBBING PADS
To ensure longer life and optimum performance, periodically
clean all sanding residue and foreign materials from the
scrubbing pads. This can be done simply by rinsing the pad
with warm water untill all foreign material has been washed
away. After cleaning, gently squeeze the pad to remove
excess water and allow pad to dry. Always store pads and
sanding sheets flat in a cool dry location.
CLEANING THE SANDING SHEETS
The sanding sheets that came with your sander are made to
be re-used. Therefore, it is important that they be cleaned
periodically to remove sanding residue and foreign material
that can accumulate over time.
To clean sanding sheets, rub the sheets with a hard rubber
block. You can also use the clean rubber sole of a shoe.
WARNING:
Always remove scrubbing or sanding pad from sander
before cleaning. Failure to do so could cause serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this tool for extended work on these types of materials.
However, if you do work with any of these materials, it is
extremely important to clean the tool using compressed air.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing dust.
If operation is dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
Page 13
Page 14
OPERATOR'S MANUAL
COMPACT FINISHING SANDER
5-1/2 in. (140 mm)
CFS1501
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
Authorized Service Center. You can also check our web site at www.ryobitools.com for a
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
CFS1501
0
Phone 1-800-525-2579
www.ryobitools.com
983000-367
8-03
Loading...