Ryobi ACR200BG Owner's Manual
PISTOL-GRIP SPRAYER
ACR200BG
WARNING:
To reduce the risk of injury, user must read and understand
the operator’s manual for their paint sprayer before using
this accessory. Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your eyes,
resulting in possible serious injury. Risk of fluid injections;
do not point at people, pets, electrical devices, or the unit
itself. Turn off the paint sprayer and relieve pump pressure
before changing or adjusting accessories.
INSTALLING THE PISTOL-GRIP SPRAYER
See Figure 1.
n Screw the collar on the high pressure hose onto the pistol-
grip sprayer by turning the hose collar clockwise.
n Use an adjustable wrench to hold the nut on the pistol-grip
sprayer and another to turn and tighten the nut on hose
end and tighten securely.
INSTALLING SPRAY TIP AND NOZZLE TIP
GUARD
See Figure 2.
See paint sprayer operator’s instructions for spraying, priming,
and cleaning before installing nozzle tip guard and spray tip.
Note all warnings regarding use of pistol-grip sprayer and the
possibility of injection.
n Turn lock-off thumbscrew counterclockwise to lock sprayer
trigger.
n Select spray tip and push securely into nozzle tip guard.
n Install tip saddle and tip seal into nozzle tip guard.
n Thread nozzle tip guard assembly onto sprayer and tighten
securely.
n Keep pistol-grip sprayer trigger locked when not in use.
REVERSIBLE
SPRAY TIP
NOZZLE TIP
GUARD
PISTOL-GRIP
SPRAYER
HOSE
COLLAR
NUT
Fig. 1
TIP SEAL
LOCK-OFF
THUMBSCREW
TIP
SADDLE
Fig. 2
SPRAY
LOCK-OFF
THUMBSCREW
USING THE PISTOL-GRIP SPRAYER
See Figure 3.
Always lock the pistol-grip sprayer trigger when you have
stopped spraying to prevent the sprayer from being bumped
or triggered accidentally and causing injection.
n Pull back and hold the trigger to operate the pistol-grip sprayer.
n Release the trigger to stop the flow of paint through the
nozzle.
To engage the lock-off:
n Turn lock-off thumbscrew counterclockwise.
To disengage the lock-off:
n Turn lock-off thumbscrew clockwise.
TRIGGER
LOCK
OFF
Fig. 3
CLEANING THE PISTOL-GRIP SPRAYER
See Figure 4.
n Turn off the paint sprayer and relieve pump pressure.
n Check that pistol-grip sprayer trigger is locked off.
n Remove pistol-grip sprayer from the high pressure hose
using two adjustable wrenches.
n Unscrew hex socket screw and lock nut to release trigger
guard from plate on the base of sprayer.
n Using wrench, turn handle counterclockwise to remove.
n Remove filter from handle, noting direction of filter.
n Thoroughly clean filter container with water (for water based
paints) or Klean Strip® Revolutionary White Formula Paint
Thinner (for oil-based paints or varnish).
n If filter has any holes, replace with new filter. NEVER
puncture filter with any object.
n Replace filter in handle, tapered end down facing back of
sprayer. Sprayer will not work if filter is improperly inserted
in handle.
n Reassemble pistol-grip sprayer in reverse order, tighten
securely.
CALIFORNIA PROPOSITION 65
WARNING:
This product, and the paints designed to be applied with
this product, may contain chemicals, including lead,
known to the State of California to cause cancer, birth
defects, or other reproductive harm. Wash hands after
handling.
LOCK-OFF
THUMBSCREW
TRIGGER
HEX SOCKET
SCREW
TRIGGER
GUARD
SPRAYER
HANDLE
LOCK NUT
FILTER
SPRAYER
NUT
SPECIFICATIONS
Maximum Pressure 3000 psi
Fig. 4
TROUBLESHOOTING
PROBLEM CAUSE POSSIBLE SOLUTION
Pistol-grip sprayer leaks. Internal sprayer parts are worn or
damaged.
Nozzle tip guard leaks. Nozzle tip guard or spray tip were
assembled improperly.
Pistol-grip sprayer will not spray. Spray tip is clogged.
Pistol-grip sprayer filter is clogged
Spray tip is not fully seated into nozzle
tip guard.
Paint pattern is weak or uneven. Pistol-grip sprayer filter is clogged
Spray tip is worn.
Material being sprayed is too thick.
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-800-525-2579
États-Unis, Téléphone 1-800-525-2579 • USA, Teléfono 1-800-525-2579
www.ryobitools.com
Contact Authorized Service Center.
Reassemble according to nozzle tip guard
and spray tip assembly instructions.
Turn spray tip 180° and spray to clean.
Clean or replace pistol-grip sprayer filter
Reassemble according to nozzle tip guard
and Spray tip assembly instructions.
Clean or replace filter
Replace spray tip.
Follow material manufacturer’s directions
and thin material as needed.
Loading...