OPERATOR’S MANUAL
FEED
DIRECTION
inch
1
0
1
2
3
Inch
1
0
1
2
3
ROUTER TABLE
A25RT01
Your router table has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
Introduction .....................................................................................................................................................................2
Warranty .......................................................................................................................................................................... 2
General Safety Rules ....................................................................................................................................................3-4
Specific Safety Rules ....................................................................................................................................................... 4
Symbols ........................................................................................................................................................................5-6
Electrical ..........................................................................................................................................................................7
Features ........................................................................................................................................................................8-9
Assembly ..................................................................................................................................................................10-16
Operation ..................................................................................................................................................................17-18
Maintenance ..................................................................................................................................................................19
Parts Ordering / Service ...................................................................................................................................Back Page
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
WARRANTY
RYOBI® POWER TOOL - LIMITED TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY
One World Technologies, Inc., warrants its RYOBI® power tools with the following conditions:
30-DAY EXCHANGE POLICY: During the first 30 days after date of purchase, you may either request service under this
warranty or you may exchange any RYOBI® power tool which does not work properly due to defective workmanship or
materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool
or requested warranty service, you must present proof of purchase and return all original equipment packaged with the
original product. The replacement power tool will be covered by the limited warranty for the balance of the two year period
from the date of the original purchase.
WHAT THIS WARRANTY COVERS: This warranty covers all defects in workmanship or materials in your RYOBI® power
tool for a period of two years from the date of purchase. With the exception of batteries, power tool accessories are
warranted for ninety (90) days. Batteries are warranted for two years.
HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to an Authorized Service
Center. You can obtain the location of the Service Center nearest you by contacting a service representative at One
World Technologies, Inc., P.O. Box 1207, Anderson, SC 29622-1207, by calling 1-800-525-2579 or by logging on to www.
ryobitools.com. When you request warranty service, you must also present proof of purchase documentation, which
includes the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either repair or replace
any defective part, at our option. We will do so without any charge to you. We will complete the work in a reasonable time,
but, in any case, within ninety (90) days or less.
WHAT’S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This
warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defects resulting
from misuse, abuse, neglect, alteration, modification or repairs by other than Authorized Service Centers. One World
Technologies, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools
other than those specifically stated in this warranty.
ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or
fitness for a particular purpose, are limited to two years from the date of purchase. One World Technologies, Inc. is not
responsible for direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
2
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Carefully read the router
table operator’s manual and the manual for the particular
router you are using. Learn the applications and limitations as well as the specific potential hazards related to
this tool.
GUARD AGAINST ELECTRICAL SHOCK BY PREVENT-
ING BODY CONTACT WITH GROUNDED SURFACES.
For example: pipes, radiators, ranges, refrigerator enclosures.
KEEP GUARDS IN PLACE and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and benches
invite accidents. DO NOT leave tools or pieces of wood
on the tool while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
K EEP CHI LDR EN AND VIS ITO RS AWAY. Al l
visitors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks, master
switches, or by removing starter keys.
DON’T FORCE THE TOOL. It will do the job better and
safer at the feed rate for which it was designed.
USE THE RIGHT TOOL. Do not force the tool or attach-
ment to do a job for which it was not designed.
USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. Use only a cord heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 14 is recommended for an extension
cord 25 feet or less in length. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
DRESS PROPERLY. Do not wear loose clothing,
neckties, or jewelry that can get caught and draw you into
moving parts. Rubber gloves and nonskid footwear are
recommended when working outdoors. Also wear protective hair covering to contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work
when practical, it is safer than using your hand and frees
both hands to operate the tool.
DO NOT OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before servicing,
or when changing attachments, blades, bits, cutters, etc.,
all tools should be disconnected from power source.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may result in injury.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. DO NOT LEAVE TOOL UNTIL IT
COMES TO A COMPLETE STOP.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never carry tool by the cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
USE OUTDOOR EXTENSION CORDS. When tool is
used outdoors, use only extension cords marked “W-A”
or “W”. These cords are rated for outdoor use and reduce
the risk of electric shock.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
3
GENERAL SAFETY RULES
I NSPE C T TOOL C O RDS PER I ODI C ALLY. I f
damaged, have repaired by a qualified service technician at
an authorized service facility. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
SPECIFIC SAFETY RULES
FOR YOUR OWN SAFETY, read this router table operator’s
manual and the router manual before operating the router
or using the router table.
ALWAYS USE THE ARTICULATING ROUTER CUTTER
BIT GUARD.
WHEN USING THE ROUTER ON THE ROUTER TABLE,
the router must be plugged into the router table switch
outlet.
KEEP HANDS AWAY FROM CUTTING AREA. Do not
reach underneath the table or in the cutting path with your
hands or fingers at any time while the tool is connected
to a power source.
DO NOT USE AWKWARD HAND POSITIONS.
FIRMLY CLAMP OR BOLT THE ROUTER TABLE TO
A WORK SURFACE so that the router table surface is
approximately hip height.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
DO NOT OPERATE A TOOL WHILE UNDER THE
IN FLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
INSPECT FOR AND REMOVE ALL NAILS FROM LUM-
BER BEFORE ROUTING. Following this rule will reduce
the risk of serious personal injury.
ALWAYS FEED WORKPIECE AGAINST ROTATION OF
CUTTER.
KEEP FINGERS AWAY FROM REVOLVING CUTTER,
USE FIXTURES WHEN NECESSARY.
ALWAYS SUPPORT WORKPIECE FIRMLY AGAINST
TABLE AND FENCE.
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions
also.
4
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
n
o
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
DESIGNATION/EXPLANATION
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s Manual
Eye Protection
Safety Alert Precautions that involve your safety.
No Hands Symbol
No Hands Symbol
No Hands Symbol
No Hands Symbol
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any hot
surface.
5
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand completely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Ryobi customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the product’s plug.
When using a power product at a considerable distance from
the power source, use an extension cord heavy enough to
carry the current that the product will draw. An undersized
extension cord will cause a drop in line voltage, resulting in
a loss of power and causing the motor to overheat. Use the
chart provided below to determine the minimum wire size
required in an extension cord. Only round jacketed cords
listed by Underwriter’s Laboratories (UL) should be used.
**Ampere rating (on product data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25
' 16 16 16 16 14 14
' 16 16 16 14 14 12
50
' 16 16 14 12 10 —
100
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the product outdoors, use an extension
cord that is designed for outside use. This is indicated by the
letters “WA” on the cord’s jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
products or other obstructions while you are working with
a power product. Failure to do so can result in serious
personal injury.
SPEED AND WIRING
The no-load speed of this product depends on the router
you are using. This speed is not constant and decreases
under a load or with lower voltage. For voltage, the wiring
in a shop is as important as the motor’s horsepower rating.
A line intended only for lights cannot properly carry a power
product motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can
support one power product may not be able to support two
or three products.
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This product is equipped with an
electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary, do
not connect the equipment-grounding conductor to a live
terminal.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the product is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is intended for use on a circuit that has an outlet
like the one shown in figure 1. It also has a grounding pin
like the one shown.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use product with a damaged
cord since touching the damaged area could cause electrical shock resulting in serious injury.
ELECTRICAL CONNECTION
This product should be connected to a power supply that is
120 volts, 60 Hz, AC only (normal household current). Do
not operate this product on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor will
overheat. If the router table does not operate when plugged
into an outlet, double check the power supply.
GROUNDING
PIN
7
120 V GROUNDED OUTLET
Fig. 1
FEED
DIRECTION
inch
1
0
1
2
3
Inch
1
0
1
2
3
Inch
1
FEED
DIRECTION
1
FEATURES
P
U
S
H
R
E
E
T
S
PRODUCT SPECIFICATIONS
Table Dimensions ............................. 14 in. x 28 in. x 3/4 in.
Maximum Cutter Diameter ................................. 1-15/16 in.
Fence Length .............................................................18 in.
Miter Slot ........................................ 1/4 in. x 3/4 in. x 28 in.
Rating .............................. 120 V, 60 Hz, AC only, 15 Amps
Net Weight ..............................................................18.5 lbs.
VACUUM PORT
THROAT PLATES
ARTICULATING ROUTER CUTTER / BIT GUARD
INSERT
PLATE
SWITCH
ASSEMBLY
RESET BUTTON
FENCE
ASSEMBLY
STARTING
PIN
MITER
GAUGE
Fig. 2
KNOW YOUR ROUTER TABLE
See Figure 2.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
FENCE ASSEMBLY
The fence assembly provides an adjustable surface to support and guide the work. Molded into the fence assembly
is the vacuum port.
INSERT PLATE
The insert plate can be used in combination with a variety
of routers. It also has pre-drilled countersunk holes that can
ARTICULATING ROUTER CUTTER / BIT
GUARD
The articulating router cutter bit guard on the fence assembly provides a barrier to protect the operator from contact
with the cutter and is designed to stay in contact with the
workpiece.
be used with a variety of routers.
MITER GAUGE
A miter gauge is used for mitered routing and to help support
wider pieces.
8
FEATURES
RESET BUTTON
See Figure 2.
The router table switch is e
protects the electronic components of the router table switch
box from overload.
quipped with a reset button that
STARTING PIN
When you are unable to use the fence for a guide because
the workpiece is odd-shaped or too small, use the starting
pin for a guide and/or pivot point. Only use piloted cutters
when using the starting pin.
THROAT PLATES
Five throat plates are included with the router table. The
throat plate provides a stable surface around the cutter and
prevents objects from falling through the throat and damaging the spindle.
VACUUM PORT
The vacuum ports molded into the fence will accept either
a 1-1/4 in. or 2-1/2 in. vacuum attachment.
SWITCH ASSEMBLY
See Figure 3.
This product is equipped with a switch assembly that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
TO TURN YOUR ROUTER TABLE ON:
Plug the router into either switch box outlet on the router
table and plug the router table into a 120 volt grounded
outlet.
With the switch key inserted into the switch, lift the switch
to turn ON ( l ).
WARNING:
Always remove the switch key when the tool is not in
use and keep it in a safe place. In the event of a power
failure, turn the switch OFF ( O ) and remove the key.
This action will prevent the tool from accidentally starting
when power returns.
WARNING:
ALWAYS make sure your workpiece is not in contact with
the cutter before operating the switch to start the tool.
Failure to heed this warning may cause the workpiece to
be kicked back toward the operator and result in serious
personal injury.
WARNING:
To reduce the risk of accidental starting, ALWAYS make
sure the switch is in the OFF ( O ) position before plugging
tool into the power source.
SWITCH
ON
SWITCH
OFF
NOTE: The router table is equipped with a reset button ( See
Figure 2 ). If, for any reason, the router table will not turn on,
press the reset button and then restart.
TO TURN YOUR ROUTER TABLE OFF:
Press the switch down to turn OFF ( O ).
TO LOCK YOUR ROUTER TABLE:
Press the switch down.
Remove the switch key from the switch and store in a
safe, secure location.
SWITCH KEY
9
SWITCH IN LOCKED POSITION
Fig. 3
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
1
2
3
1
2
3
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to heed
this warning could result in serious personal injury.
1
2
3
4
5
6
8
7
9
10
WARNING:
The undertable guards must be securely in place before
using the router table. Failure to do so could result in
serious personal injury.
19
20
17
18
16
12
11
15
14
13
Fig. 4
PACKING LIST
1. Table Leg (4)
2. Table Leg Phillips Head Screw (16)
3. Starting Pin
4. Table Top
5. Switch Box Nut (3)
6. Switch Box Screw (3)
7. Switch Box
8. Carriage Bolt Washer (2)
9. Carriage Bolt (2)
10. Hex Key (1)
11. Under Table Guard (2)
12. Throat Plates (5)
13. Router Insert Plate Screws (
5/16-18 x 3/4 in.) (3)
14. Router Insert Plate Screws (10-24 x 5/8 in.) (3)
15. Router Insert Plate Screws (10-32 x 5/8 in.) (3)
16. Under Table Guard Screw (6)
17. Miter Gauge
18. Fence Assembly
19. Fence Lock Knob (2)
20. Fence Lock Knob Washer (2)
21. Operator’s Manual (not shown)
10
ASSEMBLY
ASSEMBLING THE ROUTER TABLE
Assembling the router table involves attaching the switch
box, the under table guards, the legs, the router/insert plate
assembly, the fence assembly, throat plate, starting pin, and
installing the miter gauge to the router table.
ATTACHING THE SWITCH BOX
See Figure 5.
The switch box will come in a bag with the switch box screws
and nuts. Use these screws and nuts in the bag to attach
the switch box.
Place the router table upside down on a flat surface.
Hold the switch box so that the words ON and OFF on
the toggle switch are upside down.
Line up the three holes in the switch box with the three
holes on the outside of the front rail, this is the rail that
is already installed on the front underside of the router
table.
Insert the switch box screws through the holes in the
switch box and through the holes in the front rail.
Install the nuts on the back of the switch box screws.
Holding the screws in place with a screwdriver, tighten
the nuts onto the screws with a wrench or socket.
SWITCH BOX
SCREW
UNDER
TABLE GUARDS
SWITCH KEY
SWITCH BOX
SWITCH
BOX NUT
FRONT RAIL
Fig. 5
UNDER TABLE
GUARD SCREW
ATTACHING THE UNDER TABLE GUARDS
See Figure 6.
The under table guards will come in a bag with the under
table guard screws. Use these screws in the bag to attach
the under table guards.
Place the router table upside down on a flat surface.
Position the under table guards in front of and behind the
insert plate. The front under table guard should have the
open ended side facing the back of the router table.
Align the three holes of the under table guards with the
holes in the table. The front under table guard will be
bolted onto the front rail.
Insert the under table guard screws through the holes
and into the table.
Tighten screws with a screwdriver.
ATTACHING THE TABLE LEGS
See Figure 7.
The table legs will come in a bag with the table leg screws. Use
the table leg screws in the bag to attach the table legs.
Place router table upside down on a flat, level surface
with the front edge closest to you.
Place each leg in a corner of the table. The legs with the
warning labels should go in the front, and the legs without
the warning labels should go in the back.
NOTE: The table leg with the English language warning
should go next to the switch box.
Align the four holes in the legs with the four corresponding
threaded holes in the table.
Insert the table leg screws through the holes and into the
table.
Tighten screws with a screwdriver.
TABLE LEG
RIGHT LEG-
FRENCH / SPANISH
LABEL
TABLE LEG SCREW
LEFT LEG-
ENGLISH LABEL
Fig. 6
FRONT SIDE
Fig. 7
11
ASSEMBLY
NOTCH
A1
A3
A5
A6
A4
B3
B4
A2
B2
B1
RD
PC2
RY
PC1
PC1
ML
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
PRE-DRILLING HOLES FOR THROUGH
TABLE DEPTH ADJUSTMENT
See Figure 8.
Since each router will have different placements for through
table depth adjustments, pilot holes have been pre-drilled in
the throat plate to assist in through table adjustments. Only
the models listed below in the key are available for use with
the through table depth adjustment feature.
Remove the throat plate.
Determine which router you have and find the pre-drilled
pilot hole that matches your router. (Refer to key be-
low.)
Using a drill and drill bit, drill a hole through the pilot hole
large enough for the depth adjustment tool (not included
with router table, but may be included with your router)
to pass though so through table depth adjustments can
be made.
Figure 8 Key:
RD: RIDGID R2930
RY: Ryobi R163K
ML: Milwaukee 5615-20, 5616-20
PC1: Porter-Cable 890 Series
PC2: Porter-Cable 8529
ATTACHING THE ROUTER TO THE TABLE
For ease of use, assemble the router to the insert plate with
the insert plate removed first, then install the insert plate/
router assembly into the router table.
PRE-DRILLED
PILOT HOLES
INSERT PLATE
REAR SIDE
Fig. 8
INSERT PLATE
FRONT SIDE
Fig. 9
ROUTER INSERT
PLATE SCREWS
ATTACHING THE ROUTER TO THE INSERT
PLATE
See Figures 9 - 10.
Remove the insert plate.
Remove the subbase plate from the router.
Using the following chart for reference, and using one of
the three included sets of three router insert plate screws,
attach the router to the insert plate with the pilot holes
facing the router and the notch in the insert plate facing
the back of the router table.
NOTE: When attaching insert plate to the router, make
sure the holes in the router base match up with the insert
plate accurately and are not off-center.
INSTALLING THE ROUTER/INSERT PLATE
ASSEMBLY
See Figure 11.
With the insert plate installed on the router, insert router
and insert plate assembly into the router table with the
notch in the insert plate facing the back of the router table
toward the fence assembly.
Install the insert plate screws and leave loose until all
adjustments have been made.
INSERT PLATE
Fig. 10
INSERT
PLATE SCREWS
NOTCH
Fig. 11
12
ASSEMBLY
BRAND MODEL BASE TYPE FASTENER SIZE INSERT PLATE HOLES USED NUMBER OF HOLES
Bosch 1617 Fixed 10-24 x 5/8 in. A1, A3, A5 3
Bosch 1617 EVS Fixed 10-24 x 5/8 in. A1, A3, A5 3
Bosch 1617 EVSPK Fixed 10-24 x 5/8 in. A1, A3, A5 3
Craftsman 17504 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17505 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17506 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17508 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17510 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17511 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17515 Plunge 5/16-18 x 3/4 in. B1, B2, B4 3
Craftsman 17517 Plunge 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17533 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 17533 Plunge 5/16-18 x 3/4 in. B1, B2, B4 3
Craftsman 24833 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Craftsman 24833 Plunge 5/16-18 x 3/4 in. B1, B2, B4 3
Craftsman 27500 Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Craftsman 26921 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Hitachi M12V Plunge 10-32 x 5/8 in. A1, A3, A5 3
Hitachi KM12VC Fixed 10-32 x 5/8 in. A1, A3, A5 3
Makita RF1101 Fixed 10-24 x 5/8 in. A1, A3, A5 3
Makita RP1101 Plunge 10-24 x 5/8 in. A1, A3, A5 3
Makita RF1101K
Milwaukee 5615-20 Fixed 10-24 x 5/8 in. A1, A3, A5 3
Milwaukee 5616-20 Fixed 10-24 x 5/8 in. A1, A3, A5 3
Porter Cable
Porter Cable
Porter Cable
Porter Cable
Porter Cable
Porter Cable
Porter Cable
RIDGID R2930
Ryobi R160 Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Ryobi R161K Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Ryobi R162K Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Ryobi R163K Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Ryobi R165U Fixed 5/16-18 x 3/4 in. B1, B2, B4 3
Ryobi R175 Plunge 5/16-18 x 3/4 in. B1, B3 2
Ryobi RE175 Plunge 5/16-18 x 3/4 in. B1, B3 2
Ryobi
Skil 1810 Fixed 10-32 x 5/8 in. A2, A4, A6 3
Skil 1825
693LRPK Plunge only 10-24 x 5/8 in. A1, A3, A5 3
694PK Plunge only 10-24 x 5/8 in. A1, A3, A5 3
694VK Plunge only 10-24 x 5/8 in. A1, A3, A5 3
892 Fixed 10-24 x 5/8 in. A1, A3, A5 3
893PK Fixed 10-24 x 5/8 in. A1, A3, A5 3
7529 Plunge 10-24 x 5/8 in. A1, A3, A5 3
8529 Plunge 10-24 x 5/8 in. A1, A3, A5 3
RE180PL/PL1
All identified trademarks and trade names are the property of their respective owners.
Fixed/Plunge
Fixed/Plunge
Plunge 5/16-18 x 3/4 in. B1, B3 2
Fixed/Plunge
10-24 x 5/8 in. A1, A3, A5 3
10-32 x 5/8 in. A1, A3, A5 3
10-32 x 5/8 in. A2, A4, A6 3
13
0
Inch
1
2
1
3
0
0
Inch
1
2
1
3
0
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
ASSEMBLY
MAKING INSERT PLATE LEVEL
See Figure 12.
Unplug the router table and/or the router.
Check to see if the insert plate mounted assembly is level
with a straight edge or level.
Using the supplied hex key, tighten or loosen the adjust-
ing screws depending on how the insert plate needs to be
adjusted in order to make the insert plate level.
Tighten insert plate screws with a screwdriver.
ATTACHING THE FENCE ASSEMBLY
See Figure 13.
Unplug the router table and/or the router.
Place the router table right side up with the back edge
closest to you.
Slide the carriage bolt washers onto the carriage bolts.
Slide carriage bolts through the slot in the router table
and through the slots in the fence assembly.
Slide the fence lock knob washer over the carriage
bolts.
Install the fence lock knobs over the carriage bolts.
Tighten the fence lock knobs.
INSERT
PLATE
STRAIGHT
EDGE
FENCE LOCK KNOB
WASHER
HEX KEY
ADJUSTING
SCREWS
Fig. 12
FENCE LOCK KNOBS
WARNING:
Make sure throat plates snap securely into place. Do
not use if snaps are damaged or throat plates do not
snap in securely. Failure to do so could result in serious
personal injury.
INSERTING AND REMOVING THROAT
PLATES
See Figure 14.
The throat plate provides a stable surface around the cutter
and prevents objects from falling through the throat plate
and damaging the spindle.
SLOT
FENCE
ASSEMBLY
CARRIAGE BOLT
WASHER
CARRIAGE BOLTS
Fig. 13
14
FEED
DIRECTION
Inch
1
0
1
2
3
2
3
Inch
1
0
1
2
3
1
2
3
FEED
DIRECTION
ASSEMBLY
1
0
1
2
3
0
1
2
3
The proper size throat plate depends on the size and shape
of the cutter. When inserted, the throat plate opening should
be within approximately 1/4 in. of the outermost edge of
the cutter.
Unplug the router table and/or the router.
Select the throat plate you wish to use.
Press throat plate into insert plate slot until it snaps into
place.
To remove, push throat plate out from the bottom of the
insert plate.
INSERTING THE STARTING PIN
See Figure 15.
Place the starting pin on the router table and use it as a pivot
point when cutting small, odd-shaped pieces.
NOTE: It is not necessary to use the fence when you are
using the starting pin, but the bit guard should be used to
cover the cutter. Additionally, only use piloted cutters when
using the starting pin.
Unplug the router table and/or the router.
Place the starting pin into the hole to the right of the router
table throat opening.
Push the pin in to secure.
INSTALLING THE MITER GAUGE
See Figure 16.
Unplug the router table and/or the router.
With the router table right side up, and the front edge
closest to you, place the miter gauge bar in the slot near
the front of the table with the pointer on the right.
THROAT PLATE
NOTCH
STARTING
PIN HOLES
TAB
Fig. 14
STARTING PIN
INSTALL
REMOVE
Fig. 15
MITER
GAUGE BAR
MITER GAUGE
POINTER
SLOT
Fig. 16
15
inch
FEED
DIRECTION
1
inch
1
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
ASSEMBLY
ATTACHING THE VACUUM HOSE
See Figure 17.
The vacuum port molded into the fence will accept either a
1-1/4 in. or 2-1/2 in. vacuum attachment.
CLAMPING THE ROUTER TABLE TO A WORK
BENCH
See Figures 18.
Unplug the router table and/or the router.
Place the router table right side up on a sturdy work
surface; e.g., leg stand, workbench, counter top.
Using a clamp, insert the top front of clamp through the
opening in the router table leg.
Tighten clamp securely.
MOUNTING THE ROUTER TABLE TO A
WORK BENCH
See Figure 19.
Unplug the router table and/or the router.
Place the router table right side up on a sturdy work
surface; e.g., leg stand, workbench, counter top.
Mark the holes with a pencil.
Remove the router table.
Drill four holes through the work surface.
Place the router table back on the work surface, align-
ing the holes in the table legs with the holes in the work
surface.
VACUUM PORT
VACUUM HOSE
Fig. 17
NOTE: Position the router table surface at approximately
hip height.
Insert four bolts (not included, 1/4-20 recommended) and
tighten securely with flat washers, lock washers, and hex
nuts (not included).
WORK TABLE
FLAT
WASHER
CLAMP
Fig. 18
BOLTS
16
HEX NUT
LOCK
WASHER
WORK TABLE
Fig. 19
OPERATION
WARNING:
Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
�Table mounted dado and mortise operations in wood and
wood composition materials
Fence guided edging operations for cabinetry and
picture framing on wood and wood compos ition
materials
Piloted cutter operations using the starting pin for
edgin g pat ter ned surf ace s o n woo d and wood
composition materials
WARNING:
The direction of feed for the workpiece is always against
the sharp edges of the cutter and therefore into the rotation of the cutter. Failure to heed this warning can result
in serious personal injury.
WARNING:
The router or router table should never be connected to
a power supply when you are assembling parts, making
adjustments, installing or removing cutters, cleaning, or
when not in use. Disconnecting the router and router table
will prevent accidental starting that could cause serious
personal injury.
PERFORMING A ROUTING OPERATION
Observe the following rules when using the router.
Read the entire operator’s manual for the router and
router table.
Plug the router table power cord into a power source.
Always control the power to the router with the router
table switch whenever the router is mounted on the
table.
Always plug the router into either of the router table
switched outlets. Never plug a router table mounted
router into another power source.
Position the infeed and outfeed fence so they are close
to the maximum diameter of the cutter, but not touching
the cutter.
NOTE: The workpiece must always be tight against
the fence, unless you are using a ball-bearing piloted
cutter.
Adjust the infeed fence to support the uncut workpiece
and adjust the outfeed fence to support the workpiece
after the cut. The “0” location on the fence scale denotes
the center of the throat opening of the table.
Reconfirm that all router adjustments are securely locked
before connecting the router table to a power source.
Feed the workpiece from right to left with the cutter in
line with the fence opening.
Make sure the router table switch is off when not in use.
Remove the switch key to ensure the router table is off.
WARNING:
When operating the router with the router table, the
router must only be plugged into and controlled by the
router table switched outlet. To reduce the risk of serious
personal injury, never connect the table mounted router
into another power source.
17
1/4
0
Inch
1
0
1
2
3
Inch
1
0
1
2
3
FEED
DIRECTION
Inch
1
0
1
2
3
Inch
1
0
1
2
3
OPERATION
0
1/4
INSERTING/REMOVING CUTTERS
Unplug the router table and/or the router.
Remove the fence assembly. (See Attaching the Fence
Assembly in the Assembly section.)
WARNING:
If you are changing a cutter immediately after use, be
careful not to touch the cutter or collet with your hands or
fingers. They will get burned because of the heat buildup
from cutting. Always use a wrench.
Remove the router/insert plate assembly. (See
Router/Insert Plate Assembly
in the Assembly sec-
Installing
tion.)
Consult the router operator’s manual for proper cutter
removal/installation procedure and replace cutter.
ADJUSTING DEPTH OF CUT
We recommend that cuts be made at a depth not exceeding
1/8 in. and that several passes be made to reach depths of
cut greater than 1/8 in.
ADJUSTING THE MITER GAUGE
See Figure 20.
Unplug the router table and/or the router.
Loosen the miter gauge knob.
Rotate the miter gauge to the desired angle.
Tighten the miter gauge knob.
FENCE LOCK KNOB
LOOSEN
MITER GAUGE
MITER
GAUGE KNOB
Fig. 20
LOCK KNOB
POSITIONING THE FENCE
See Figure 21.
The fence enables you to support and guide the workpiece.
Unplug the router table and/or the router.
Loosen the fence lock knobs.
Position the fence to the desired location.
Tighten the fence lock knobs.
NOTE: The outfeed fence has joining capabilities and can
be adjusted out in increments up to 1/4 in. and enable
you to support the workpiece as it exits the cutter.
When making a side or edge cut, never position the fence
such that the workpiece is located between the cutter
and the fence. Failure to heed this warning can result in
serious personal injury.
WARNING:
SCALE
TIGHTEN
OUTFEED FENCE
CUTTER
PROPER
DISTANCE
SCALE
Fig. 21
18
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Electric tools used on fiberglass material, wallboard, spack
ling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently, we do not recommend
using this product for extended work on these types
of materials. However, if you do work with any of these
materials, it is extremely important to clean the product
using compressed air.
-
19
OPERATOR’S MANUAL
ROUTER TABLE
A25RT01
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
• MODEL NUMBER
• SERIAL NUMBER
A25RT01
• HOW TO OBTAIN REPLACEMENT PARTS:
Replacement parts can be purchased online at www.ryobitools.com or by calling
1-800-525-2579. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
Authorized Service Centers can be located online at www.ryobitools.com or by calling
1-800-525-2579.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
Ryobi® is a registered trademark of Ryobi Limited used under license.
987000-114
03-08-07 (REV:00)
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-525-2579
www.ryobitools.com
20
Loading...