Ryobi 41CD875A034 Owner’s Manual
OPERATOR'S MANUAL
i i ¸¸iii iiiiiiiiiiiiiii ¸ iiiiiiiiiiiiiii i iii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiii ¸¸¸ iiiiiiiiii i¸iii ¸ i
iiiiiiiiiiiiiiiiiiiiiiiii_!ill__ii_!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!_i_ iiii!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iii_
....iiiiiiiiiiiiiiiiiiiiiiiiiiii ¸ iiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiii¸¸ iiiiiiiiiiiiii
IMPORTANT MANUAL
DO NOT THROW
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator's manual provides you with eesy-to-
understand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition. The other
manual that came with your power tool, the parts
manual, contains all the information that you need to
order parts,
PRODUCT REFERENCES, ILLUSTRATIONS AND
SPECIFICATIONS
All information, illustrationsand specifications in this
manual are based on the latest product information
available at the time of printing, We reserve the right to
make changes at any time without notice.
Copyright © 1998 Ryobi Outdoor Products, Inc.
All Rights Reserved.
ClickoLink ® isa registered trademark of Ryobi Outdoor
Products.
SpeedSpool ® is a registered trademark of Ryobi
Outdoor Products.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
Dial:
• 1-800-345-8746 or www.ryobi,com on the world wide
web for authorized service dealers in the United States
Or
• 1-800-265-6778 in Canada to obtain the listing of the
authorized service dealer nearest you,
to obtain the listing of the authorized service dealer
nearest you.
DO NOT RETURN THE UNIT TO THE RETAILER.
NOTE: PROOF OF PURCHASE WILL BE REQUIRED
FOR WARRANTY SERVICE.
Make sure this manual is carefully read and understood
before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE
US PATENTS, OTHER PATENTS PENDING.
L
California EmissionRegulations ................. 3
II.
Rules for Safe Operation ..................... 4-8
A. Important Safety Information ............... 4-5
B. Safety and International Symbols ........... 6-7
C. Know Your Unit ........................... 8
III.
Assembly Instructions ........................ 9
A. Adjusting the J handle ...................... 9
IV.
Oil and Fuel Information ................... 10-11
A. Recommended Oil Type ................... 10
B. Adding Oil to Crankcase-Initial Use ........... 10
C. Recommended Fuel Type .................. 11
D. Fueling the Unit .......................... 11
V.
Starting/Stopping Instructions ................. 12
VI.
Operating Instructions .................... 13-15
A. Operating the Click-Link System ............. 13
B. Holding the Trimmer ...................... 14
C, Adjusting Trimming Line Length ............. 14
D. Tips for Best Trimming Results .............. 14
E. Decorative Trimming ...................... 15
VII. Maintenance and Repair Instructions ......... 15-24
A. Maintenance Schedule .................... 15
B. Line Installation for the SpeedSpool .......... 16
C. Installing a Prewound Reel ................. 17
D, Cleaning the SpeedSpool .................. 18
E. SpeedSpool Replacement Parts ............. 18
F, Checking the Oil Level ..................... 19
G.Changing the Oil ......................... 19
H, Air Filter Maintenance ..................... 20
I. Carburetor Adjustment .................... 21
J. Rocker Arm Clearance ..................... 22
K. Replacing the Spark Plug .................. 24
L. Spark Arrestor Maintenance ................ 24
M.Accessories/Replacement parts ............. 24
VIII, Cleaning and Storage ........................ 25
IX. Troubleshooting Chart ....................... 26
X. Specifications .............................. 27
Xl. Warranty ............................... 29-30
CONTENTS OF CARTON
This carton should includeof the following:
• Model 875r Trimmer with J-Handle
• Operator's Manual
• Parts Manual
• Product Registration Card
• Bottle of 4-Cycle Oil
ThisenginemeetsU.S.EPAPH1and2000modelyearandlaterCaliforniaemissionsregulationsforsmalloff-road
engines.Theseunitsareidentifiedbythelabelontheengineof your product. A typical identification label is shown.
To ensure that your unit continues to meet these regulations, refer to the following information and instructions in this
operator's manual.
f
California Proposition 65 Warning:
RYOBI®
IMPORTANTENGINEiNFORMATII
ENGINEDISPLACEMENT2_2cc
ENGINEFAMILY:..XN4XS.O26,M_Elf
1HISBiG_ N_ETSU.S.B_APHI
AND2000M(X)R.YEARAIDL._
_JFORMAEMSSIONM FOR_
SMALLOIT-.ROADI RB:BTO
OPBATOR'SIFOR E
m110NS N_An,Jtb'll_n_
NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest
Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that
certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark
arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these
requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If it requires
replacement, ask your LOCAL SERVICE dealer to install the Accessory Part #180890 Spark Arrestor Screen,
FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-265-6778 in CANADA
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
Read the Operator's Manual(s) and follow all warnings and safety instructions. Failure to do so can
result in serious injury to the operator and/or oystanders.
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols, and
their explanations, deserve your careful attention and
understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL MEANING
_ SAFETY ALERT SYMBOL: Indicates
NOTE: Advises you of information or instructions vital
to the operation or maintenance of the equipment.
danger, warning, or caution. Attention is
required in order to avoid serious personal
injury. May be used in conjunction with other
symbols or pictographs.
• IMPORTANT SAFETY INFORMATION °
will result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock, and
l,_ ANGER: Failure to obey a safety warning
personal injury.
WARNING: Failure to obey a safety warning
can result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock, and
personal injury.
CAUTION: Failure to obey a safety warning
may result in property damage or personal
injury to yourself or to others. Always follow
the safety precautions to reduce the risk of
fire, electric shock, and personal injury.
READ ALL INSTRUCTIONS
BEFORE OPERATING
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
• Inspect the unit before use. Replace damaged parts.
Check for fuel leaks, Make sure all fasteners are in
place and secure. Replace cutting attachment parts
that are cracked, chipped, or damaged in any way.
Make sure the cutting attachment is properly installed
and securely fastened. Be sure the cutting attachment
shield is properly attached, and positioned as
recommended. Failure to so can result in personal
injury to the operator and bystanders, as well as
damage to the unit.
• Use only 0.080 inch (2.03 mm) diameter genuine Ryobi
replacement line. Never use metal-reinforced line,
wire, or rope, etc.. These can break off and become a
dangerous projectile.
• Be aware of the risk of injury to the head, hands and
feet.
• Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be thrown or become entangled in
the cutting attachment. Clear the area of children,
bystanders, and pets. At a minimum, keep all children,
bystanders and pets outside a 50 feet (15 m.) radius;
there still may be a risk to bystanders from thrown
objects. Bystanders should be encouraged to wear
eye protection. If you are approached, stop the engine
and cutting attachment immediately.
• Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using unit.
• This unit was not designed to be used as a
brushcutter. Do not attach or operate this unit with any
type of brushcutting blade or brushcutting attachment.
SAFETY WARNINGS FOR GAS TRIMMERS
WARNING: Gasoline is highly flammable, and its vapors
can explode if ignited. Take the following precautions:
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel
tank, or add fuel, when the engine is hot. Never
operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure
in the tank.
Add fuel in a clean, well-ventilated area outdoors
where there are no sparks or flames. Slowly remove
the fuel cap only after stopping engine. Do not smoke
while fueling or mixing fuel. Wipe up any spilled fuel
from the unit immediately.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke, keep sparks and open flames from the area
while adding fuel or operating the unit.
A
WHILE OPERATING
• Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate
this unit only in a well ventilated area outdoors.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty. Long sleeve shirts
are recommended.
• Wear heavy, long pants, boots and gloves. Do not
wear loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.
• The cutting attachment shield must always be in place
while operating the unit. Do not operate unit without
both trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.
• This unit has a clutch. The cutting attachment remains
stationary when the engine is idling. If it does not, have
the unit adjusted by an authorized service technician.
• Adjust the J-Handle to your size to provide the best
grip.
• Be sure the cutting attachment is not in contact with
anything before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. See
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for the purpose
intended.
• Do not overreach. Always keep proper footing and
balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both the front and rear handle or
grips.
• Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it is rotating.
• Do not touch the engine or muffler. These parts get
extremely hot from operation. When turned off they
remain hot for a short time.
• Do not operate the engine faster than the speed
needed to cut, trim or edge. Do not run the engine at
high speed when not cutting.
• Always stop the engine when cutting is delayed or
when walking from one cutting location to another.
• If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
• Stop and switch the engine to off for maintenance,
repair, or for changing the cutting attachment or other
attachments.
• Use only genuine Ryobi replacement parts when
servicing this unit. These parts are available from
your authorized service dealer. Do not use parts,
accessories or attachments not authorized by Ryobi
for this unit. Doing so could lead to serious injury to
the user, or damage to the unit, and void your
warranty.
• Keep unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.
• To reduce fire hazard, replace faulty muffler and spark
arrestor, keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
OTHER SAFETY WARNINGS
• Never store the unit, with fuel in the tank, inside a
building where fumes may reach an open flame or
spark.
• Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high
to prevent unauthorized use or damage, out of the
reach of children.
• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning, or caution. May be used in conjunction with other
symbols or pictographs.
• WARNING - READ OPERATOR'S MANUAL
Read the Operator's Manual(s) and follow all warnings and safety instructions.
Failure to do so can result in serious injury to the operator and/or bystanders.
• FOR SERVICE INFORMATION, CALL:
USA: 1-800-345-8746
i
e
CANADA: 1-800-265-6778
• WEAR EYE AND HEARING PROTECTION
WARNING: Thrown objects and loud noise can cause severe eye injury and hearing loss.
Wear eye protection meeting ANSI Z87.1-1989 standards and ear protection when
operating this unit.
5-7X
• KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders, especially children and pets, at least 50 feet (15 m.)
from the operating area.
• PRIMER BULB
Push primer bulb, fully and slowly, 5 to 7 times.
• UNLEADED FUEL
Always use clean, fresh unleaded fuel.
• OIL
Refer to operator's manual for the proper type of oil.
SYMBOL MEANING
• THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY
WARNING: Do not operate without the cutting attachment shield in place.
Keep away from the rotating cutting attachment.
• ON/OFF STOP CONTROL
ON / START / RUN
• ON/OFF STOP CONTROL
OFF OR STOP
• HOT SURFACE WARNING
Do not touch a hot muffler or cylinder. You may get burned. These parts get extremely hot
from operation. When turned off they remain hot for a short time.
m
• SHARP BLADE
WARNING: Sharp blade on cutting attachment shield. To prevent serious injury, do not
touch line cutting blade.
• CHOKE CONTROL
A" FULL choke position.
B • PARTIAL choke position.
C • RUN position.
WARNING: The operation of any power tool can cause foreign objects to be thrown into your
eyes. This can lead to severe eye damage. Before commencing power tool operation, always
wear safety glasses or goggles that are marked as meeting ANSI Z87.1-1989 standards, and
a full face shield when needed.
APPLICATIONS
As a trimmer;
• Cutting grass and light weeds.
• Edging
• Decorative trimming around trees, fences, etc.
Other optional accessories may be used with the 875r.
See list of add-ons on page 13.
Spark Arrestor
Muffler Guard
Fuel Cap
On/Off Stop Control
Shaft Grip
Throttle
Control
Shaft Housing
Line Cutting Blade
Cutting Attachment
Shield
Cutting Attachment
J-Handle
Air Filter Cover
Engine Feet
Choke Lever
Spark Plug
Oil Fill Plug / Dipstick
ADJUSTING THE J-HANDLE
1. Loosen the four (4) screws holding the J-handle in
place (Fig. 1). Do not completely remove the screws.
J-Handle
(4) Screws
Fig. 1
2, Slide the J-handle in or out until the arrow/white line
on the decal touches the clamp assembly (Fig. 2).
.
While holding the unit in the operating position
(Fig. 3), position the J-handle to the location
that provides you the best grip.
Fig. 3
4. Tighten the clamp screws evenly, until the J-handle
is secure.
Fig. 2
4
Loading...