Page 1
410r
2-Cycle Garden Cultivator
OPERATOR’S MANUAL
FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or
1-800-265-6778 in CANADA
www.ryobi.com
IMPORTANT MANUAL DO NOT THROW AWAY
Page 2
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition.
The other manual that came with your power tool, the
parts manual, contains all the information that you need
to order parts.
PRODUCT REFERENCES, ILLUSTRATIONS AND
SPECIFICATIONS
All information, illustrations and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright
©
1999 Ryobi Outdoor Products, Inc.
All Rights Reserved.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
Dial:
• 1-800-345-8746 or www.ryobi.com on the world wide
web for authorized service dealers in the United States
Or
• 1-800-265-6778 in Canada to obtain the listing of the
authorized service dealer nearest you.
to obtain the listing of the authorized service dealer
nearest you.
DO NOT RETURN THE UNIT TO THE RETAILER.
NOTE: PROOF OF PURCHASE WILL BE REQUIRED
FOR WARRANTY SERVICE.
Make sure this manual is carefully read and understood
before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE
US PATENTS, OTHER PATENTS PENDING.
INTRODUCTION
2
TABLE OF CONTENTS
I. California Emission Regulations . . . . . . . . . . . . . . . . . 3
II. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 4-7
A. Important Safety Information . . . . . . . . . . . . . . . . . 4
B. Safety and International Symbols . . . . . . . . . . . . . 5
C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
III. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . 8-10
A. Assembling the Unit . . . . . . . . . . . . . . . . . . . . . . . . .8
B. Installing the Wheel Bracket Assembly . . . . . . . . . 8
C. Installing the Handlebar . . . . . . . . . . . . . . . . . . . . . 9
D. Throttle Cable Assembly . . . . . . . . . . . . . . . . . . . 10
IV. Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . 11
V. Starting/Stopping Instructions . . . . . . . . . . . . . . . . . 12
VI. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . 13
A. Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B. Adjusting Tine Depth . . . . . . . . . . . . . . . . . . . . . . 13
VII. Maintenance and Repair Instructions . . . . . . . . . 14-16
A. Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 14
B. Tine Removal and Replacement . . . . . . . . . . . . . 14
C. Air Filter Maintenance . . . . . . . . . . . . . . . . . . . . . 14
D. Carburetor Setting . . . . . . . . . . . . . . . . . . . . . . . . 16
E. Replacing the Spark Plug . . . . . . . . . . . . . . . . . . 16
VIII. Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . 17
A. Cleaning the Unit . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C. Accessories/Replacement parts . . . . . . . . . . . . . 17
D. Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . 17
E. Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
IX. Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 18
X. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
XI. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
CONTENTS OF CARTON
This unit includes the following:
• Model 410r Garden Cutivator
• Handlebar with Clamps
• Hardware Pack
• Bottle of 2-Cycle Oil
• Operator's Manual
• Parts Manual
Examine all parts to make certain that nothing is missing
and no breakage has occurred during shipping. Any
damaged or missing part must be replaced before using
this product.
Page 3
3
CALIFORNIA EMISSION REGULATIONS
WARNING
NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest
Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that
certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark
arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these
requirements could subject you to liability or a fine. This unit is not factory equipped with a spark arrestor. If these
items are required in your area, ask your LOCAL SERVICE dealer to install the Optional Accessory Part #180030 Spark
Arrestor Kit.
FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-265-6778 in CANADA
California Proposition 65 Warning:
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
This unit meets the 1995 to 1999 California emissions regulations for small off-road engines. These units are identified by
the label on the engine of your product. A typical identification label is shown.
To ensure that your unit continues to meet these regulations, refer to the following information and instructions in this
operator’s manual.
Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can
result in serious injury to the operator and/or bystanders.
SPARK ARRESTOR
WARNING!
WARNING: The operation of any power tool can cause foreign objects to be thrown into your
eyes. This can lead to severe eye damage. Before commencing power tool operation, always
wear safety glasses or goggles that are marked as meeting ANSI Z87.1 standards, and a full
face shield when needed.
Page 4
RULES FOR SAFE OPERATION
4
DANGER: Failure to obey a safety warning
will result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock, and
personal injury.
WARNING: Failure to obey a safety warning
can result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock, and
personal injury.
CAUTION: Failure to obey a safety warning
may result in property damage or personal
injury to yourself or to others. Always follow
the safety precautions to reduce the risk of
fire, electric shock, and personal injury.
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols, and
their explanations, deserve your careful attention and
understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates
danger, warning, or caution. Attention is
required in order to avoid serious personal
injury. May be used in conjunction with other
symbols or pictographs.
NOTE:Advises you of information or instructions vital to
the operation or maintenance of the equipment.
READ ALL INSTRUCTIONS
BEFORE OPERATING
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
• All guards and safety attachments must be installed
properly before operating the unit.
• Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace parts that are cracked,
chipped, or damaged in any way. Do not operate the
unit with loose or damaged parts.
• Carefully inspect the area before starting the unit.
Remove all debris and hard or sharp objects such
as glass, wire, etc.
• Clear the area of children, bystanders, and pets.
At a minimum, keep all children, bystanders and pets
outside a 50 feet (15 m) radius; there still may be a risk
to bystanders from thrown objects. Bystanders should
be encouraged to wear eye protection. If you are
approached, stop the unit immediately.
• Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
WARNING: Gasoline is highly flammable, and its vapors
can explode if ignited. Take the following precautions:
• Store fuel only in containers specifically designed and
approved for the storage of such materials.
• Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
• Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel
tank, or add fuel, when the engine is hot. Never
operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure
in the tank.
• Mix and add fuel in a clean, well-ventilated area
outdoors where there are no sparks or flames. Slowly
remove the fuel cap only after stopping engine. Do not
smoke while fueling or mixing fuel. Wipe up any spilled
fuel from the unit immediately.
• Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke, keep sparks and open flames from the area
while adding fuel or operating the unit.
WHILE OPERATING
• Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate
this unit only in a well ventilated area outdoors.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
• Wear heavy, long pants, boots, gloves and long sleeve
shirt. Do not wear, short pants, sandals or go barefoot.
• To reduce the risk of injury associated with objects
being drawn into rotating parts, do not wear loose
clothing, jewelry, scarves, etc. Secure hair above
shoulder level.
• Use the unit only in daylight or good artificial light.
• Keep outside surfaces free from oil and fuel.
• This unit has a clutch. The tines remain stationary
when the engine is idling. If they do not, have the unit
adjusted by an authorized service technician.
• IMPORTANT SAFETY INFORMATION •
Page 5
RULES FOR SAFE OPERATION
5
• Be sure the tines are not in contact with anything
before starting the unit.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. See
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for the purpose
intended.
• Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
• Use extreme caution when reversing or pulling the unit
towards you.
• Do not overreach, take extra care when working on
steep slopes or inclines. Always keep proper footing
and balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on the handlebar grips.
• Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the tines
when they are rotating. Do not operate without guards
in place.
• Do not touch the engine, muffler or gearbox. These
parts get extremely hot from operation. When turned
off they remain hot for a short time.
• Do not operate the engine faster than the speed
needed to do the job. Do not run the engine at high
speed when not in use.
• Always stop the engine when operation is delayed or
when walking from one location to another.
• Stop the engine for maintenance, repair, to install or
remove the tines. The unit must be stopped and the
tines no longer turning to avoid injury.
• The tines become very sharp from use. Always wear
heavy gloves when handling, removing, installing or
cleaning the tines.
• Use only genuine Ryobi replacement parts and accessories for this unit. These are available from
your authorized service dealer. Use of any non Ryobi
parts or accessories could lead to serious injury to the
user, or damage to the unit, and void your warranty.
• Keep unit clean of vegetation and other materials.
They may become lodged between the tines and
gearbox or guard.
• To reduce fire hazard, replace faulty muffler and spark
arrestor, keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
OTHER SAFETY WARNINGS
• Never store the unit, with fuel in the tank, inside a
building where fumes may reach an open flame or
spark.
• Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
• Store the unit in a dry place, either locked up or up
high to prevent unauthorized use or damage.
Keep out of the reach of children.
• Clean the tines with a hose and water. Wipe the tines
with a light machine oil to prevent rust.
• Never douse or squirt the engine with water or any
other liquid. Keep handles dry, clean and free from
debris. Clean after each use, see Cleaning and
Storage instructions.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning, or caution. May be used in conjunction with other
symbols or pictographs.
• WARNING - READ OPERATOR'S MANUAL
Read the Operator’s Manual(s) and follow all warnings and safety instructions.
Failure to do so can result in serious injury to the operator and/or bystanders.
• FOR SERVICE INFORMATION, CALL:
USA: 1-800-345-8746
CANADA: 1-800-265-6778
Page 6
SYMBOL MEANING
• WEAR EYE AND HEARING PROTECTION
WARNING:
Thrown objects and loud noise can cause severe eye injury and hearing
loss. Wear eye protection meeting ANSI Z87.1 standards and ear protection when
operating this unit.
• KEEP BYSTANDERS AWAY
WARNING:
Keep all bystanders, especially children and pets, at least 50 feet (15 m)
from the operating area.
• PRIMER
Push primer bulb, fully and slowly, 5 to 7 times.
• UNLEADED FUEL
Always use clean, fresh unleaded fuel.
• OIL
Refer to operator's manual for the proper type of oil.
• THROWN OBJECTS CAN CAUSE SEVERE INJURY
WARNING:
Do not operate unit without proper attachments and guards in place.
• ON/OFF STOP CONTROL
ON / START / RUN
• ON/OFF STOP CONTROL
OFF OR STOP
• HOT SURFACE WARNING
Do not touch a hot muffler, cylinder or gearbox. You may get burned. These parts get
extremely hot from operation. When turned off they remain hot for a short time.
• CHOKE CONTROL
A • FULL choke position.
B •
PARTIAL choke position.
C •
RUN position.
• GARDEN CULTIVATORS – ROTATING TINES CAN CAUSE SEVERE INJURY
WARNING:
Stop the engine and allow the tines to stop before installing or
removing tines, or before cleaning or performing any maintenance.
Keep hands and feet away from rotating tines.
RULES FOR SAFE OPERATION
6
Page 7
RULES FOR SAFE OPERATION
7
KNOW YOUR UNIT
Tine Guard
Tines
Gearbox
Primer Bulb
Choke Control
Air Filter/
Muffler Cover
Spark
Plug
Muffler
Fuel Cap
On/Off Stop
Control
STOP/OFF (O)
START/ON (I)
Throttle
Control
Throttle
Cable
Handlebar
Clamp
Starter Rope Grip
Handlebar
Wheel Bracket
Assembly
Shaft Tube Grip
Handgrip
Handgrip
APPLICATION
Use this unit for cultivating sod and light to medium soil.
Also for cultivating in garden areas, around trees, etc.
Page 8
ASSEMBLY INSTRUCTIONS
8
Fig. 1
Fig. 2
Fig. 3
ASSEMBLING THE UNIT
Your yard and garden cultivator has been completely
assembled except for the handlebar, throttle cable and
wheel bracket assembly. A large phillips screwdriver is
needed for assembly.
Unpacking
1. Carefully unpack the contents and insure that
nothing is damaged. Unwrap the throttle cable
without bending or kinking it.
WARNING: Do not cut the plastic strap off
the handle bar. The strap is under tension
and can cause serious personal injury if cut.
2. Squeeze the handle bar and slide the plastic strap
down and off (Fig. 1).
NOTE: Do not squeeze the handlebar too tight.
Excessive squeezing can cause the handlebar
to kink.
Squeeze
Together
Plastic
Strap
INSTALLING THE WHEEL BRACKET ASSEMBLY
WARNING: To avoid injury from the tines,
wear heavy gloves and a long sleeve shirt
when installing the wheel bracket assembly.
1. With the unit on it’s side, place the wheel bracket
assembly on the underside of the tine guard (Fig. 2).
2. Install a carriage bolt through each of the slotted
holes in the wheel bracket and into the tine guard.
3. On the top side of the tine guard, install a lock
washer and a wing nut onto each of the bolts (Fig. 2).
4. Make sure the square shoulder of the bolts are
through the slotted holes in the wheel bracket.
Tighten the wing nuts (Fig. 3).
NOTE: Do not over tighten the wing nuts. Loosening the
wing nuts allow the wheel height to be adjusted.
Wing Nut &
Lock Washer
Tine
Guard
Wheel
Bracket
Assembly
Page 9
ASSEMBLY INSTRUCTIONS
9
Fig. 6
Fig. 5
Fig. 7
INSTALLING THE HANDLEBAR
1. Place the handlebar between the bottom and middle
clamp pieces (Fig. 4).
2. While holding the three pieces together, position the
handlebar underneath the shaft tube and align with
the top clamp.
NOTE: The holes in the clamp assembly will line up only
when assembled correctly.
3. One at a time, hold a hex nut in the bottom clamp
recess with a finger and install a screw through the
clamp assembly. Start screw with a large Phillips
screwdriver. do the same with the other three (3)
nuts and screws. Do not tighten until you make the
handle adjustment.
4. Position the two (2) handlebar clamps with one on
each side near the top.of the handlebar. Swing the
handlebar up until it sets to the outside of the two
mounting brackets on the engine (Fig.5).
NOTE: Positioning the handlebar onto the mounting
brackets may require slightly spreading the
handlebar.
5. Slide the two (2) handlebar clamps down over the
mounting brackets (Fig. 6).
NOTE: It may be required to loosen or remove the
thumb screws on the handlebar clamps to
spread them to fit over the mounting brackets.
6. Center the handlebar and tighten the two (2)
mounting bracket clamps and the four (4) handlebar
clamp screws evenly until the handlebar is secure.
(Figs. 6 and 7).
Fig. 4
Bottom
Clamp
Nut
Middle
Clamp
Thumb
Screw
Clamp
Mounting
Bracket
Mounting
Bracket
Spacer
Nut
Handlebar
Screw
Top
Clamp
Handlebar Clamp
Handlebar
Handlebar
Page 10
ASSEMBLY INSTRUCTIONS
10
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Throttle Wire Hole
Throttle
Wire Slot
Fig. 8
THROTTLE CABLE ASSEMBLY
1. Wrap the throttle wire once around the handlebar
(Fig. 8).
2. Depress the throttle trigger and locate hole for the
throttle wire (Fig. 9).
3. With the throttle trigger depressed, place the barrel
end of the throttle wire inside the hole of the trigger
(Fig. 10).
4. Release the throttle trigger and guide the cable up
into the slot of the trigger housing.
5. Push the throttle cable housing into the trigger
housing until it snaps into place (Fig. 11).
6. Route the throttle cable through the clip on the right
handlebar mounting bracket (Fig. 12).
NOTE: Ensure the throttle cable is fitting into the guide
at the carburetor plate on the engine. If it does
not, the throttle will not work properly (Fig. 8).
Throttle Cable
Carburetor
Plate Guide
Mounting
Bracket
Throttle
Cable
Engine
Page 11
OIL AND FUEL INFORMATION
11
WARNING: Gasoline is extremely
flammable. Ignited Vapors may explode.
Always stop the engine and allow it to cool
before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING: Remove fuel cap slowly to avoid
injury from fuel spray. Never operate the unit
without the fuel cap securely in place.
WARNING: Add fuel in a clean, well
ventilated area outdoors. Wipe up any spilled
fuel immediately. Avoid creating a source of
ignition for spilt fuel. Do not start the engine
until fuel vapors dissipate.
NOTE: Dispose of the old fuel/oil mix in accordance to
Federal, State, and Local regulations.
FILLING THE FUEL TANK
Fill or add fuel to the tank only when the cultivator is in a
horizontal position (Fig. 13).
OIL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons
for the unit not running properly. Be sure to use fresh,
clean unleaded fuel. Follow the instructions carefully for
the proper fuel/oil mixture.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms
acids when stored. When using alcohol-blended fuel,
use fresh fuel (less than 60 days old).
Using Blended Fuels
If you choose to use a blended fuel, or its use is
unavoidable, follow recommended precautions.
• Always use fresh fuel mix per your operator's manual.
• Use the fuel additive STA-BIL® or an equivalent.
• Always agitate the fuel mix before fueling the unit.
• Drain the tank and run the engine dry before storing
the unit.
Using Fuel Additives
The use of fuel additive, such as STA-BIL® Gas
Stabilizer or an equivalent, will inhibit corrosion and minimize the formation of gum deposits. Using a fuel additive can keep fuel from forming harmful deposits in the
carburetor for up to six (6) months. Add 0.8 oz. (23 ml.)
of fuel additive per gallon of fuel according to the
instructions on the container. NEVER add fuel additives
directly to the unit's fuel tank.
CAUTION: For proper engine operation and
maximum reliability, pay strict attention to the
oil and fuel mixing instructions on the 2-cycle
oil container. Using improperly mixed fuel can
severely damage the engine.
Thoroughly mix the proper ratio of 2-cycle engine oil
with unleaded gasoline in a separate fuel can. Use a 32:1
fuel/oil ratio. Do not mix them directly in the engine fuel
tank. See the table below for specific gas and oil mixing
ratios.
NOTE: One gallon (3.8 liters) of unleaded gasoline mixed
with one 4 oz. (120 ml.) bottle of RYOBI 2 CYCLE
OIL makes a 32:1 fuel/oil ratio.
+
UNLEADED GAS RYOBI 2 CYCLE OIL
1 US. GALLON + 4.0 FL. OZ.
(3.8 LITERS) (120 ml)
1 LITER + 30 ml
MIXING RATIO - 32:1
Fig. 13
Page 12
STARTING/STOPPING INSTRUCTIONS
12
Choke Control
Full Choke
Position (A)
Starter
Rope
Throttle
Control
Primer Bulb
Fig. 16
STARTING INSTRUCTIONS
WARNING: Avoid accidental starting. Be in
the starting position when pulling the starter
rope (Fig. 16). The operator and unit must be
in a stable position while starting to avoid
serious personal injury.
WARNING: Operate this unit only
in a well ventilated area outdoors. Carbon
monoxide exhaust fumes can be lethal in a
confined area.
1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.
See Oil and Fuel Mixing Instructions Pg. 11.
2. Put the On/Off Stop Control in the START (I) position
(Fig. 14).
3. Fully press and release primer bulb slowly 5 to 7
times. Fuel should be visible in the bulb (Fig. 15).
If fuel is not visible, press three (3) more times, or
until it is.
4. Place the choke lever in the FULL choke position
(A ) (Fig. 15).
5. With the unit on the ground, squeeze the throttle
control and pull starter rope briskly (Fig. 16).
Continue pulling until the engine sounds as
though it wants to run (normally 2 to 5 pulls).
NOTE: Squeeze the throttle control until the engine has
started and warmed up.
6. Place the choke lever in the PARTIAL choke position
(B ) (Fig. 15).
NOTE: The unit will not run in the FULL choke position
(A ).
7. Pull starter rope briskly 1 to 3 times to start the
engine (Fig. 16).
8. If the engine does not start, repeat steps
4 through 7.
Fig. 14
Fig. 15
Run
Position (C)
Partial Position (B)
NOTE: If the engine floods while trying to start, place the
choke lever in the RUN position (C ) (Fig. 15).
Squeeze the throttle control. Pull the starter rope
briskly. The engine should start within three (3) to
eight (8) pulls.
9. Squeeze the throttle control to warm up engine for 5
to 10 seconds. Place the choke lever in the RUN
position (C ) (Fig. 15).
NOTE: Choking is unnecessary when starting a warm
engine. Put the On/Off Stop Control in the
START (I) position (Fig. 14), and start in PARTIAL
Choke position (B ) (Fig. 15).
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control (Fig. 16).
Allow the engine to cool down by idling.
2. Put the On/Off Stop Control in the STOP (O) position
(Fig. 14).
On/Off Stop
Control
STOP/OFF (O)
START/ON (I)
Page 13
Transporting the Unit
WARNING: To prevent serious personal
injury, always stop the engine when
operation is delayed or when transporting
the unit from one location to another.
1. Stop the engine.
2. Slide the wheel bracket assembly all the way down.
3. Tilt the unit back until the tines clear the ground.
4. Push or pull the unit to the next location to be
cultivated.
OPERATING INSTRUCTIONS
13
Fig. 17
Fig. 18
OPERATING TIPS
WARNING: Dress properly to reduce the risk
of injury when operating this unit. Do not
wear loose clothing or jewelry. Wear eye and
ear/hearing protection. Wear heavy, long pants,
boots and gloves. Do not wear short pants,
sandals or go barefoot.
1. Move the cultivator to the work area prior to starting
the engine. The cultivator may be transported by
pushing it on wheels or carrying it by the shaft
tube grip.
WARNING: To prevent serious personal
injury, never pick-up or carry the unit while
the engine is running.
2. Start the unit per Starting Instructions.
3. With the engine running and the tines off the ground,
depress the throttle control to increase the engine
speed.
4. Holding both of the handlebar grips firmly, slowly
lower the cultivator until the tines make contact with
the ground (Fig. 17).
5. As cultivating action begins, pull back on the
cultivator so that the tines can penetrate the ground.
6. Once the ground has been broken, continue at a
moderate pace until you are familiar with the controls
and the handling of the cultivator.
7. Pull the cultivator backwards to improve the depth of
cultivation and reduce your effort.
8. If the tines are digging too deep or not deep enough,
adjust the tines per Adjusting Tine Depth.
ADJUSTING TINE DEPTH
Tine adjustment will vary depending on the type of soil
being cultivated and how it will be used. Generally,
adjusting the tines to break the soil 4 to 6 inches is
recommended for most gardens. Adjust the tines as
follows:
1. Stop the engine and disconnect the plug wire.
2. Loosen (do not remove) the two wing nuts on the
tine guard (Fig. 18).
3. Slide the wheel bracket assembly down for shallower
and up for deeper tine penetration.
4. Once the tines are in the desired position, tighten the
wing nuts, making sure that the carriage bolts are
seated properly through the bracket.
5. If the tine depth is not correct, repeat steps 2 to 4.
Down
Up
Page 14
MAINTENANCE AND REPAIR INSTRUCTIONS
14
AIR FILTER MAINTENANCE
Removing the Air Filter/Muffler Cover
WARNING: To avoid serious personal
injury, always turn the unit off and allow it
to cool before you clean or perform any
maintenance on it.
1. Place the choke control in the PARTIAL choke
position (B).
NOTE: The choke control must be in the PARTIAL
choke position (B) (Fig. 21) to remove the
air filter/muffler cover.
2. Remove the four (4) screws securing the air
filter/muffler cover (Fig. 21). Use a flat blade or # T20
Torx bit screwdriver.
3. Pull the cover from the engine. Do not force.
Clevis Pin Clip
Felt Cushion
Clevis Pin
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures take your unit to an authorized
service dealer.
MAINTENANCE SCHEDULE
These required maintenance procedures should be
performed at the frequency stated in the table. They
should also be included as part of any seasonal tune-up.
MAINTENANCE REQUIRED
Fill fuel tank with correct oil and fuel mixture.
Clean and re-oil air filter.
Check spark plug condition and gap.
FREQUENCY
Before Starting Engine
Every 10 Hours
Every 50 Hours
REFER TO:
Page 11
Page 15
Page 16
WARNING: To prevent serious injury, never
do maintenance or repairs with unit running.
Always do maintenance and repairs on a
cool unit. Disconnect spark plug wire to
ensure the unit will not start.
Fig. 19
Fig. 20
TINE REMOVAL AND REPLACEMENT
All 4 tines should be replaced at the same time because
they will wear evenly through normal use. Work on one
side at a time.
WARNING: To prevent serious personal
injury, always wear heavy gloves when
handling the tines.
1. Put the On/Off Stop Control in the STOP (O) position
and disconnect the spark plug wire.
2. Remove the clevis pin clips and clevis pins (Fig. 19).
3. Remove the tines and felt cushions from the shaft.
4. Clean and oil the shaft.
5. Replace the tines and felt cushions by reversing
steps 2 and 3 (Fig. 20).
NOTE: When installed correctly, the hubs on the tines
will face each other and the letter “R” stamped
on the tines will appear on the right side of the
cultivator and the letter “L” will appear on the
left side from the normal operating position. It is
important that the tines are installed correctly.
6. Repeat this procedure on the opposite side.
Page 15
MAINTENANCE AND REPAIR INSTRUCTIONS
15
Cleaning the Air Filter
WARNING: To avoid serious personal
injury, always turn the unit off and allow it
to cool before you clean or perform any
maintenance on it.
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Not maintaining the
air filter will VOID the warranty.
1. Remove the air filter/muffler cover. See Removing
the Air filter/Muffler Cover.
2. Remove the air filter from behind the air filter/muffler
cover. (Fig. 22).
3. Wash the filter in detergent and water (Fig. 23). Rinse
the filter thoroughly. Squeeze out excess water.
Allow it to dry completely.
4. Apply enough clean SAE 30 oil to lightly coat the
filter (Fig. 24).
5. Squeeze the filter to spread and remove excess oil
(Fig. 25).
6. Replace the air filter in the air filter/muffler cover
(Fig. 22).
NOTE: Operating the unit without the air filter and
air filter/muffler cover assembly, will VOID the
warranty.
Fig. 23
Air Filter
Fig. 22
Fig. 24
Choke Control
Screws
Screws
Partial Choke
Position (B)
Fig. 21
Fig. 25
Reinstalling the Air filter/Muffler Cover
1. Place the air filter/muffler cover over the back of the
carburetor and muffler.
NOTE: The choke control must be in the PARTIAL
choke position (B) (Fig. 21) to install the air filter/muffler cover.
2. Insert the four (4) screws into the holes in the air
filter/muffler cover (Fig. 21) and tighten. Use a flat
blade or # T20 Torx bit screwdriver. Do not over
tighten. Do not force.
Page 16
MAINTENANCE AND REPAIR INSTRUCTIONS
16
REPLACING THE SPARK PLUG
Use a Champion RDJ7Y spark plug (or equivalent). The
correct air gap is 0.020 in. (0.5 mm.). Remove the plug
after every 50 hours of operation to check its condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull the cap from the spark plug.
2. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning a 5/8 in.
socket counterclockwise.
NOTE: Replace cracked, fouled or dirty spark plug.
3. Set the air gap at 0.020 in. (0.5 mm.) using a feeler
gauge (Fig. 27).
0.020 in.
(0.5 mm.)
Fig. 27
CAUTION: Do not sand blast, scrape, or
clean electrodes. Grit in the engine could
damage the cylinder.
4. Install a correctly gaped spark plug in the cylinder
head. Tighten by turning the 5/8 in. socket clockwise
until snug.
If using a torque wrench torque to;
110-120 in.•lb.. (12.3-13.5 N•m).
Do not over tighten.
CARBURETOR SETTING
The idle speed adjuster of the engine is adjustable
through the Air filter/muffler cover (Fig 26).
NOTE: Careless adjustments can seriously damage your
unit. An authorized service dealer should make
carburetor adjustments.
Check Fuel Mixture
Old and/or improperly mixed fuel is usually the reason
for the unit not running properly. Drain and refill the tank
with fresh, properly mixed fuel prior to making any
adjustments. Refer to Oil and Fuel Information, Pg. 11.
Clean Air Filter
The condition of the air filter is important to the
operation of the unit. A dirty air filter will restrict air flow
and change the air/fuel mixture. This is often mistaken
for an out of adjustment carburetor. Check the condition
of the air filter before adjusting the idle speed adjuster.
Refer to
Air Filter Maintenance Pg. 14.
Adjust Idle Speed Adjuster
WARNING: This unit will need to be running
during idle speed adjustment. Wear
protective clothing and observe all safety
instructions to prevent serious personal
injury.
If after checking the fuel mixture and cleaning the
air filter the engine still will not idle, adjust the idle speed
screw as follows.
1. Start the engine and let it run at a high idle for a
minute to warm up. See Starting/Stopping
Instructions, Pg. 12.
NOTE: Ensure the tines are not in contact with the
ground when adjusting the idle.
2. Release the throttle control and let the engine idle. If
the engine stops, insert a small phillips or flat blade
screwdriver into the hole in the air filter/muffler cover
(Fig. 26). Turn the idle speed screw in, clockwise,
1/8 of a turn at a time (as needed) until the engine
idles smoothly.
NOTE: The tines should not rotate when the engine
idles.
3. If the tines rotate when the engine idles, turn the idle
speed screw counterclockwise 1/8 of a turn at a
time (as needed), to reduce idle speed.
Checking the fuel mixture, cleaning the air filter, and
adjusting the idle speed screw should solve most engine
problems.
If not and:
• The engine will not idle,
• The engine hesitates or stalls on acceleration,
• There is a loss of engine power,
have the carburetor adjusted by an authorized service
dealer.
Idle Speed Adjuster
Fig. 26
Page 17
CLEANING AND STORAGE
17
CLEANING THE UNIT
WARNING: To avoid serious personal
injury, always turn the unit off and allow it
to cool before you clean or perform any
maintenance on it.
• Use a small brush to clean off the outside of the unit
and to keep the air vents free of obstructions.
• Do not use strong detergents or petroleum based
cleaners, such as kerosene. Some household
cleaners contain aromatic oils such as pine and
lemon that can damage the plastic housings or
handles. Wipe off any moisture with a soft cloth.
STORAGE
• Never store the unit with fuel in the tank where
fumes may reach an open flame or spark.
• Allow the engine to cool before storing.
• Store the unit in a locked up area to prevent
unauthorized use or damage.
• Store the unit in a dry, well ventilated area.
• Store the unit out of the reach of children.
ACCESSORIES/REPLACEMENT PARTS
2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311
Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000
Tine (Left Outer or Right Inner) . . . . . . . . . . . . . . .147471
Tine (Right Outer or Left Inner) . . . . . . . . . . . . . . .147472
Clevis Pin with Clip . . . . . . . . . . . . . . . . . . . . . . .147473
LONG TERM STORAGE
If the unit will be stored for an extended time,
1. Drain all fuel from the fuel tank into a container. Do
not use fuel that has been stored for more than 60
days. Dispose of the old fuel in accordance to local
regulations.
2. Start the engine and allow it to run until it stalls. This
ensures that all fuel has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and
put 1 oz. (30 ml.) of high quality motor oil into the
cylinder. Pull the starter rope slowly to distribute the
oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start the
unit after storage.
4. Thoroughly clean the unit and inspect for any loose
or damaged parts. Repair or replace damaged parts
and tighten loose screws, nuts or bolts. The unit is
ready for storage.
TRANSPORTING
• Allow the engine to cool before transporting.
• Secure the unit while transporting.
• Drain the fuel tank before transporting.
• Tighten fuel cap before transporting.
Page 18
TROUBLESHOOTING
18
CAUSE ACTION
Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for
carburetor adjustment
Cultivator tines bound with dirt or grass Stop the unit, switch the On/Off Stop Control to
STOP, clean and remove any debris binding the tines
CAUSE ACTION
On/Off Stop Control in the STOP position Turn the On/Off Stop Control to START
Empty fuel tank Fill fuel tank
Primer bulb wasn't pressed enough Press primer bulb fully and slowly 5-7 times
Engine flooded Use starting procedure with choke control in the
RUN position, Pg. 12
Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture
Fouled spark plug Replace or clean the spark plug
ENGINE WILL NOT START
ENGINE WILL NOT IDLE
ENGINE WILL NOT ACCELERATE
ENGINE LACKS POWER OR STALLS WHEN UNDER LOAD
CAUSE ACTION
Air Filter is Plugged Replace or clean the air filter
Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture
Improper carburetor adjustment Adjust per instruction Pg. 16
CAUSE ACTION
Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for
carburetor adjustment
Page 19
SPECIFICATIONS
19
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 cc
Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,800-3,600 rpm
Operating RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6,700-9,000 rpm
Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centrifugal
Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic
On/Off Stop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle Switch
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.020 inch (0.5 mm)
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture
Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32:1
Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position
Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto Rewind
Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard
Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring Return
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ounces (415 ml)
Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HD Polyethylene
ENGINE
DRIVE SHAFT AND CULTIVATOR
Drive Shaft Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steel Tube
Throttle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Finger-Tip Trigger
Cultivating Path Width (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 inches (22.86 cm)
Cultivating Depth (Maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 inches (15.24 cm)
Weight (no fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.5 lb. (11.2 kg)
Page 20
NOTES
20
Page 21
21
The California Air Resources Board and Ryobi
Outdoor Products (ROP), are pleased to explain the
emission control system warranty on your 1995 and
later small off-road engine. In California, new small
off-road engines must be designed, built and
equipped to meet the State's stringent anti-smog
standards. ROP must warrant the emission control
system on your small off-road engine for the periods
of time listed below provided there has been no
abuse, neglect or improper maintenance of your small
off-road engine.
Your emission control system may include parts such
as the carburetor or fuel injection system, the ignition
system, and catalytic converter. Also included may be
hoses, belts, connectors and other emission-related
assemblies.
Where a warrantable condition exists, ROP will repair
your small off-road engine at no cost to you including
diagnosis, parts and labor.
The 1995 and later small off-road engines are
warranted for two years. If any emission-related part
on your engine is defective, the part will be repaired
or replaced by ROP.
OWNER'S WARRANTY RESPONSIBILITIES:
• As the small off-road engine owner, you are
responsible for the performance of the required
maintenance listed in your operator's manual. ROP
recommends that you retain all receipts covering
maintenance on your small off-road engine, but
ROP cannot deny warranty solely for the lack of
receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the small off-road engine owner, you should
however be aware that ROP may deny you warranty
coverage if your small off-road engine or a part has
failed due to abuse, neglect, improper maintenance
or unapproved modifications.
• You are responsible for presenting your small
off-road engine to a Ryobi Authorized Service
Center as soon as a problem exists. The warranty
repairs should be completed in a reasonable
amount of time, not to exceed 30 days.
If you have any questions regarding your warranty
rights and responsibilities, you should call
1-800-345-8746.
MANUFACTURER'S WARRANTY COVERAGE:
• The warranty period begins on the date the engine
or equipment is delivered to the retail purchaser.
• The manufacturer warrants to the initial owner and
each subsequent purchaser, that the engine is free
from defects in material and workmanship which
cause the failure of a warranted part for a period of
two years.
• Repair or replacement of warranted part will be
performed at no charge to the owner at an
Authorized Ryobi Service Center. For the nearest
location, please contact Ryobi at: 1-800-345-8746.
• Any warranted part which is not scheduled for
replacement, as required maintenance which is
scheduled only for regular inspection to the effect of
"Repair or replace as necessary" is warranted for
the warranty period. Any warranted part which is
scheduled for replacement as required maintenance
will be warranted for the period of time up to the
first scheduled replacement point for that part.
• The owner will not be charged for diagnostic labor
which leads to the determination that a warranted
part is defective, if the diagnostic work is performed
at an Authorized Ryobi Service Center.
• The manufacturer is liable for damages to other
engine components caused by the failure of a
warranted part still under warranty.
• Failures caused by abuse, neglect or improper
maintenance are not covered under warranty.
• The use of add-on or modified parts can be
grounds for disallowing a warranty claim. The
manufacturer is not liable to cover failures or
warranted parts caused by the use of add-on or
modified parts.
• In order to file a claim, go to your nearest
Authorized Ryobi Service Center. Warranty services
or repairs will be provided at all Authorized Ryobi
Service Centers.
• Any manufacturer approved replacement part
may be used in the performance of any warranty
maintenance or repair of emission related parts
and will be provided without charge to the owner.
Any replacement part that is equivalent in
performance or durability may be used in
non-warranty maintenance or repair and will
not reduce the warranty obligations of the
manufacturer.
• The following components are included in the
emission related warranty of the engine, air filter,
carburetor, primer, fuel lines, fuel pick up/fuel filter,
ignition module, spark plug and muffler.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
Page 22
ALL IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE TWO (2) YEAR WARRANTY
PERIOD OR NINETY (90) DAYS FOR PRODUCTS
USED FOR ANY COMMERCIAL PURPOSE.
ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES
INCLUDING MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OTHERWISE, ARE
DISCLAIMED IN THEIR ENTIRETY AFTER THE
EXPIRATION OF THE APPROPRIATE TWO-YEAR
OR NINETY DAY WARRANTY PERIOD. RYOBI’S
OBLIGATION UNDER THIS WARRANTY, IS STRICTLY
AND EXCLUSIVELY LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS, AND ROP
DOES NOT ASSUME OR AUTHORIZE ANYONE TO
ASSUME FOR THEM ANY OTHER OBLIGATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
RYOBI ASSUMES NO RESPONSIBILITY FOR
INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO
EXPENSE OF RETURNING THE RYOBI PRODUCT
TO AN AUTHORIZED SERVICE DEALER AND
EXPENSE OF DELIVERING IT BACK TO THE
OWNER, MECHANIC’S TRAVEL TIME, TELEPHONE
OR TELEGRAM CHARGES, RENTAL OF A LIKE
PRODUCT DURING THE TIME WARRANTY SERVICE
IS BEING PERFORMED, TRAVEL, LOSS OR DAMAGE
TO PERSONAL PROPERTY, LOSS OF REVENUE,
LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
OR INCONVENIENCE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.
This warranty applies to all RYOBI Products
manufactured by RYOBI and sold in the United States
and Canada.
To locate your nearest service dealer dial
1-800-345-8746 in the United States or
1-800-265-6778 in Canada.
RYOBI OUTDOOR PRODUCTS
550 N. 54th Street
Chandler, AZ 85226 U.S.A.
RYOBI CANADA INC.
275 Industrial Rd
Cambridge, Ontario N1R 6K2 CANADA
RYOBI OUTDOOR PRODUCTS warrants each new
RYOBI Product for two (2) years according to the
following terms.
This warranty extends to the original retail purchaser
only and commences on the date of original retail
purchase.
Any part of the RYOBI Product manufactured or
supplied by RYOBI and found in the reasonable
judgement of RYOBI to be defective in material or
workmanship will be repaired or replaced by an
authorized RYOBI service dealer without charge for
parts and labor.
The RYOBI Product including any defective part must
be returned to an authorized service dealer within the
warranty period. The expense of delivering the RYOBI
Product to the dealer for warranty work and the
expense of returning it back to the owner after repair
or replacement will be paid for by the owner. RYOBI’s
responsibility in respect to claims is limited to making
the required repairs or replacements and no claim of
breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any RYOBI
Product. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty
work must be performed by an authorized RYOBI
service dealer.
This warranty is limited to ninety (90) days from the
date of original retail purchase for any RYOBI Product
that is used for rental or commercial purposes, or any
other income-producing purpose.
This warranty does not cover any RYOBI Product that
has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way
contrary to the operating instructions as specified in
the RYOBI Operator’s Manual. This warranty does not
apply to any damage to the RYOBI Product that is the
result of improper maintenance or to any RYOBI
Product that has been altered or modified so as to
adversely affect the product's operation, performance
or durability or that has been altered or modified so as
to change its intended use. The warranty does not
extend to repairs made necessary by normal wear or
by the use of parts or accessories which are either
incompatible with the RYOBI Product or adversely
affect its operation, performance or durability.
In addition, this warranty does not cover:
A. Tune-ups - Spark Plugs, Carburetor Adjustments,
Filters
B. Wear items - Starter Pulley,Starter Ropes, Tines
RYOBI reserves the right to change or improve the
design of any RYOBI Product without assuming
any obligation to modify any product previously
manufactured.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FOR QUESTIONS CALL 1-800-345-8746 IN U.S.
OR 1-800-265-6778 IN CANADA
OPERATOR’S MANUAL PART NO. 182580 REV. B (7360)
PRINTED IN U.S.A. 7/99
LIMITED TWO-YEAR WARRANTY
Loading...