RVS Systems RVS-RS108-MV User Manual
Buzzer
Control
module
Lef t
3M3M
Rig ht
R L
1
2
Microwave
sensors
LED L EFT (Gr een/B lue)
LED R IGHT (W hite/ Black )
ACC (Red)
Ground (Black)
Turning light L (Brown)
Turning light R (Purple)
A-pillar LED alert
keep flashing
Microwave Blind Spot Sensor System Function
Control
module
LED L EFT (Gr een/B lue)
LED R IGHT (W hite/ Black )
ACC (Red)
Turning light L (Brown)
Turning light R (Purple)
side mirror
(or LED
alerts)
CANH (Blue)
CANL (Green)
Ground (Black)
Extra
OBD plug
Connect to
the OBD port
Buzzer
Lef t
3M3M
Rig ht
R L
1
2
Microwave
sensors
Wiring
MICROWAVE SENSOR
MICROWAVE BLIND SPOT
SENSOR SYSTEM
RVS-119
MANUAL
Blind spots exist around every vehicle.
The RVS-BES02-MV gives the driver visual and aural
alerts when an object enters the blind spots to the side
and behind their vehicle.
Side mirror OR
A-Pillar LED
Alert
NOTICE:
*
The Microwave Blind Spot System is intended as a driving
aid. In addition to using the device, visual confirmation from
the driver is necessary to safety change lanes. The system
may not function properly in severe weather. Turning on the
emergency blinker will turn the system off.
An LED flashing alert and aural buzzer warning will occur
when the turn signal is on and there is a vehicle in the
blind spot. The warning will continue until the detected
vehicle leaves the blind spot area. The OBD plugin
model will only operate at speeds above 4 MPH.
With turn signal on
Side mirror OR
Off
Lo
Hi
Warning buzzer
Specifications:
Working Voltage: 12V
Operation Current: 200mA
Power Consumption: 2.4W
Working Temperature: -40℃~ +85℃
Sensor Detecting Range: 15m
Sensor Detecting Angle: 72°
LED or
side mirror alerts
OBD Plugin Wiring
NOTICE:
*Side mirror add-on and OBD model are only compatible with specific
vehicle models. Please check availability with retailer.
*Only one type of display alert (LED or side mirror) are included in each
model of kit.
ACC (Red)
Turning light L (Brown)
Turning light R (Purple)
1
2
Buzzer
1,2
R
Control module
Microwave
sensor
LED alert or
L
L
L
Wiring diagram for LEFT hand drive vehicle
Buzzer
1,2
L
ACC (Red)
Turning light L (Purple)
Turning light R (Brown)
Control module
2
1
LED alert or
R
Microwave
sensor
L
R
R
3M
sti cker
3M
sti cker
R L
Front
L R
Type A
R
L
R
Front
L R
Type B
3M st icker
R L
∅15mm
Off
Hi
Lo
ACC
Turning light
L/R
Display warning
alert L
Ground or
OBD plugin
Connect all the
cables of main wire
harness to each port
L R
R
Space r wi th
3M stic ke r
Back
Side
Rear
bumpe r
side mirror
Wiring diagram for RIGHT hand drive vehicle
Microwave Sensor Installation
Take the rear bumper off and
locate a s pot in the corn er of the INNER
SIDE OF TH E REAR BUMPER ( close
to the rear) to attach the microwave
sensor. The installation should be at least
45 cm from the ground.
Use adhesive to fasten the sensorspacer to rear
bumper. Avoid dripping the adhesive on the sensors.
Microwave Sensor Detection Area
A-pillar LED Alert Installation
Take the A-pillar trim cover off and
use the included 15mm saw to drill
a mounting hole close to the
sightline of the side mirror.
Proper sensor
detection area
covers both
traveling and
adjacent lanes
Mirror Installation
1) Take the side mirror off, remove the original mirror and
disassemble the housing. 2) Thread the mirror cable
through the holder out back to the vehicle.
3) Replace the original mirror with the mirror and remount
the housing. Install the exterior mirror back to the car front
door. Using the included adapter cable connect the mirror
to the main wire harness.
NOTIC E:
* Turning light wire L/R installation in LEFT hand drive vehicle is
opposite to that in a RIGHT hand drive vehicle.
* Sensors cannot installed with the metal bumper. Make sure no
metals or wires cover the front area of microwave sensors.
side mirror
*If reverse sensors are already installed, place microwave sensors
beside them. Reverse sensors should face outmost.
Take the rear bumper off and
locate a s pot in the corn er of the CAR
FRAME to attach the microwave sensor.
The installation should be at least 45 cm
from the ground.
*Disa sse mbling se nsors wil l cau se damage a nd vo id the warr anty.
Thread the LED alert terminal and
wire through the hole and connect
the alert cable. Snap the LED alert
onto mounting hole. Reinstall
pillar cove
r.
A-
The LED alert can also be installed
on triangular panels of front door if
sufficient space is available.
Place the buzzer on the dash and
fasten with included double-sided
sticker. Connect wires to control
module.
*Adapter cable only included in side mirror kit.
Finishing installation
Install the control
module behind the
lower dashboard panel
Thread sensor wires
to trunk to connect
the sensors
Loading...