Congratulations on purchasing a Rear View Backup Camera
System! With this manual you will be able to properly install and
operate the unit.
The Backup Camera System is intended to be installed as a
supplemental aid to the rear view mirror in your vehicle. The
Backup Camera System should not be used as a substitute for the
standard rear view mirror or for any other mirror in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located for-
ward of the back of the driver’s seat or in any location that is vis-
ible, directly or indirectly, to the driver while operating the
vehicle.
4
REAR VIEW SAFETY
Safety Information
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage
and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to
this product.
warranty.
Improper installation will void manufacturer’s
USAGE
•
The Rear View Camera System
is designed to help the driver
safely detect people and/or
objects helping to avoid
damage or injury. However,
you the driver, must use it
properly. Use of this system is
not a substitute for safe,
proper or legal driving.
• Never back up while looking
at the monitor alone. You
should always check behind
and around the vehicle when
backing up, in the same way
as you would if the vehicle
did not have the Rear View
Reverse With Confidence
™
Camera System. If you back
up while looking only at the
monitor, you may cause
damage or injury. Always
back up slowly.
• The Rear View Camera Sys-
tem is not intended for use
during exstensive back-up
maneuvers or backing into
cross traffic or pedestrian
walkways.
• Please, always remember,
the area displayed by the
Rear View Camera System is
limited. It does not display
the entire panorama that is
behind you.
5
Safety Information
INSTALLATION
• Electric shock or product
malfunction may occur if
this product is installed
incorrectly.
• Use this product within
the voltage range specified.
Failure to do so can cause
electronic shock or product
malfunction.
• Take special care when
cleaning the monitor.
• Make sure to firmly affix the
product before use.
• If smoke or a burning smell
is detected, disconnect the
system immediately.
• Where the power cable may
touch a metal case, cover the
cable with a friction tape. A
short circuit or disconnected
wire may cause a fire.
• While installing the Rear
View System be careful with
the wire positioning in order
to avoid wire damage.
• The Rear View System should
only be used when the vehicle is in reverse.
• Do not watch movies or
operate the monitor while
driving; as it may cause an
accident.
• Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
• Dropping the unit may cause
possible mechanical failure.
6
REAR VIEW SAFETY
Safety Information
If you have questions about this product, contact:
Customer Service:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: 1.800.764.1028
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Reverse With Confidence
™
7
Before You Begin Installation
Before You Begin Installation
Before drilling please check that no cable or wiring is on the
other side of the wall. Please clamp all wires securely to reduce
the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical
noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed,
perform a system function test by temporarily connecting the
system. If the system seems to not be operating properly see
troubleshooting (page 15).
8
REAR VIEW SAFETY
Installation Guide
Camera & Cable
When installing the camera at the rear of the vehicle, remove the existing tailgate handle and replace with the tundra tailgate handle.
Be sure to position the cable properly. The aviation camera cable uses
aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges,
do not kink the cable and keep away from HOT and rotating parts.
Fasten all cables and secure all excess cable. Connect camera to the
camera extension cable which runs inside the vehicle. Attach camera to
the center of the license plate are using the screws provided and adjust
the angle. Figure 1.1
Wiring
After connecting the camera to the "camera cable" the camera should
be plugged into AV2 input. Connect the RED 12V power wire to a an
nition power source and the BLACK 12V ground wire to a chassis
ground.
The GREEN wire is the REVERSE trigger wire. Connect this wire to the
vehicle’s backup light circuit to activate the rear-view image whenever
the vehicle shifts into reverse. To connect a second camera, connect it
to AV1 and it can be turned on by pressing the power button on the
monitor. Figure 1.2
ig-
Reverse With Confidence
™
9
Installation Guide
Safety
• Before drilling, be sure no cable or wire is on the other side.
• Feed as much cable as possible into vehicle & clamp securely. This reduces the possibility of
cable being hooked or snagged.
• Camera: Drill a 20mm (0.8in) diameter hole into vehicle body near the
camera and bracket. Insert camera cable into vehicle (be careful not to
kink cable) and fit grommet into hole. Apply sealant around grommet to
increase resistance to water penetration.
10
REAR VIEW SAFETY
Adjustable Grid Line
Reverse With Confidence
™
11
Installation and Wiring
Figure 1.1
Figure 1.2
12
REAR VIEW SAFETY
Splicing
1.
2.
3.
4.
5.
1. Red - Power (+)
2. Yellow - Video
3. Green - Mirror / Normal Imaging
4. White - Audio
5. Black - Ground (-)
Reverse With Confidence
™
13
Positioning
14
REAR VIEW SAFETY
Troubleshooting
No Image On Screen
• Do a hard reset, unplug all
cables and power cables, leave
out for 1 minute and then
re-connect them.
• Check to ensure that the con-
nection to the camera is tight.
• Verify camera cable is plugged
into port labeled Backup Camera
• Verify that the green positive
trigger on power harness is
put to power 12v+.
Reverse With Confidence
™
• Verify camera is on correct
camera input
• Verify cable is connected to
monitor
• Verify camera is connected to
cable
• Connect known working
camera and cable to monitor.
• Verify Green trigger is receiv-
ing power
15
Camera Dimensions
4" (H) x 7.95" (L) x 0.25 "(D)
16
REAR VIEW SAFETY
Camera Specifications
Camera1/3 SONY IC Sensor
Current ConsumptionMAX: 150mA
SensorCMD-III, 1/4”
Resolution (TV Lines)420
Minimum illumination0.5 Lux
Angle170°
Effective Pixels648*488
TV SystemNTSC
Video OutputFull color vdeo out:
1.0Vp-p 75(ohm) load
Working VoltageDC9-16V
Video ColorFull color
Water Proof
IP67
Operating Temperature-30°C to +70°C
Parking guar lineOn/Off Switchable
ImageMirror
Reverse With Confidence
™
17
Warranty
One Year Warranty
Rear View Safety Inc. warrants this product against material defects
for a period of one year from date of purchase. We reserve the right
to repair or replace any such defective unit at our sole discretion.
Rear View Safety Inc. is not responsible for a defect in the system as
a result of misuse, improper installation, damage or mis-handling of
the electronic components. Rear View Safety Inc. is not responsible
for consequential damages of any kind.
This warranty is void if: defects in materials or workmanship or damages result from
repairs or alterations which have been made or attempted by others or the unauthorized use of nonconforming parts; the damage is due to normalware and tear, this
damage is due to abuse, improper maintenance, neglect or accident: or the damage is
do to use of the Rear View Safety Inc. system after partial failure or use with improper accessories.
Warranty Performance
DURING THE ABOVE WARRANTY PERIOD, SHOULD YOUR Rear View Safety
PRODUCT EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP, SUCH DEFECT
WILL BE REPAIRED WHEN THE COMPLETE Rear View Safety INC. PRODUCT IS
RETURNED, POSTAGE PREPAID AND INSURED, TO Rear View Safety INC.
OTHER THAN THE POSTAGE AND INSURANCE REQUIREMENT, NO CHARGE
WILL BE MADE FOR REPAIRS COVERED BY THIS WARRANTY.
Warranty Disclaimers
NO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THE
ABOVE WARRANTY IS MADE WITH REGARD TO THIS Rear View Safety INC.
Rear View Safety INC. DISCLAIMS ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE AND ALL OTHER
WARRANTIES IN NO EVENT SHALL Rear View Safety INC. LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR ANY
COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS
18
REAR VIEW SAFETY
Disclaimer
Rear View Safety and/or its affiliates does not guarantee or promise
that the user of our systems will not be in/part of an accident or
otherwise not collide with an object and/or person. Our systems are
not a substitute for careful and cautious driving or for the consistent
adherence to all applicable traffic laws and motor vehicle safety
regulations. The Rear View Safety products are not a substitute for
rearview mirrors or for any other motor vehicle equipment mandated
by law. Our camera systems have a limited field of vision and do not
provide a comprehensive view of the rear or side area of the vehicle.
Always make sure to look around your vehicle and use your mirrors
to confirm rearward clearance and that your vehicle can maneuver
safely. Rear View Safety and/or its affiliates shall have no responsibility or liability for damage and/or injury resulting from accidents
occurring with vehicles having some of Rear View Safety products
installed and Rear View Safety and/or its affiliates, the manufacturer,
distributor and seller shall not be liable for any injury, loss or
damage, incidental or consequential, arising out of the use or
intended use of the product. In no event shall Rear View Safety
and/or its affiliates have any liability for any losses (whether direct
or indirect, in contract, tort or otherwise) incurred in connection
with the systems, including but not limited to damaged property,
personal injury and/or loss of life. Neither shall Rear View Safety
and/or its affiliates have any responsibility for any decision, action
or inaction taken by any person in reliance on Rear View Safety
systems, or for any delays, inaccuracies and/or errors in connection
with our systems functions.
Reverse With Confidence
™
19
If you have any questions
about this product, contact:
Rear View Safety, Inc.
1797 Atlantic Avenue
Brooklyn, NY 11233
800.764.1028
BETTER CAMERAS. BETTER SERVICE.
IT’S OUR GUARANTEE.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.