Instruction Manual
OEM Frameless Rear View Replacement
Mirror Monitor with 7.2" Dual Display
RVS-718-7
Reverse With Condence ™
1
NOTE!
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a Rear View Backup
Camera System!
With this manual you will be able to properly install and
TABLE OF CONTENTS
Introduction.............................. 03
Safety Information.............................. 04-06
Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . 07
Installation Guide. . ........................... . 08
Viewing Options.................................09
Wiring.................................10
Touch Screen . . . . . . . . . . .........................11
Menu . . . . . . . . . . .....................12
Grid Lines. . . . ................. . . . . . . . 13-14
Specications . . ................. . . . . . . . . 15
Warranty.......................... . . . . . 16
Disclaimer.......................... . . . . . 17
operate the unit.
The Backup Camera System is intended to be installed as a
INTRODUCTION
supplement aid to your standard rear view mirror that already exists
in your vehicle. The Backup Camera System should not be used as a
substitute for the standard rear view mirror or for any other mirror
that exists in your vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
2 3
Rear View Safety Reverse With Condence ™
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
• Electric shock or product
malfunction may occur if this
product is installed
INSTALLATION:
or disconnected wire may cause a
re.
Improper installation will void manufacturer’s warranty.
USAGE:
• The Rear View Camera System is
designed to help the driver safely detect people and/or objects
helping to avoid damage or injury.
However, you the driver, must use it
properly. Use of this system is not a
substitute for safe, proper or legal
driving.
damage or injury. Always back up
slowly.
• The Rear View Camera System is
not intended for use during extensive back-up maneuvers or backing
into cross trac or pedestrian walkways.
incorrectly.
• Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
• Take special care when
cleaning the monitor.
• While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
• The Rear View System should only
be used when the vehicle is in
reverse.
• Do not watch movies or
operate the monitor while driving;
SAFETY INFORMATION
• Never back up while looking at the
monitor alone. You should always
check behind and around the vehi-
SAFETY INFORMATION
cle when backing up, in the same
way as you would if the vehicle did
not have the Rear View Camera
System. If you back up while looking
only at the monitor, you may cause
•Please, always remember, the area
displayed by the Rear View Camera
System is limited. It does not display
the entire panorama that is behind
you.
• Make sure to rmly ax the prod-
uct before use.
• If smoke or a burning smell
is detected, disconnect the
system immediately.
• Where the power cable may touch
a metal case, cover the cable with
friction tape. A short circuit
as it may cause an
accident.
• Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
• Dropping the unit may cause
possible mechanical failure.
4 5
Rear View Safety Reverse With Condence ™
If you have questions about this product, contact:
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: 1.800.764.1028
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
BEFORE YOU BEGIN
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
SAFETY INFORMATION
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
6 7
Rear View Safety Reverse With Condence ™
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
Original Mirror Installation
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Windshield
Dangerous
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
windshield
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous
Ok
Windshield
Dangerous
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
Please make sure to install the mirror to
the end of the bottom without any loose
windshield
windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualied help.
Dangerous
Ok
Windshield
Windshield
Dangerous
Ok
1. 2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install rear view mirror along this directionTake down your original mirror, and make
Please make sure to install the mirror to
the end of the bottom without any loose
windshield
windshield
Viewing Options
The view can be changed with triggers or manually with the wire
control.
Original mirror
1 2
3
1) Take down original mirror
windshield
Windshield plate
windshield
VIEWING OPTIONS
2) Install rear view mirror
3) Tighten rear view mirror
INSTALLATION GUIDE
Caution: Do not force mount
8 9
Rear View Safety Reverse With Condence ™
Wiring Touch Screen Operation
TOUCH BUTTONS OPERATION
MENU SETTING
In “ full display screen” state, short press “ ” to enter into menu setting interface .“ ” and “ ” are to
change the gure of each setting.
BRIGHTNESS
50
to left camera
to right camera
to front camera
to back up camera
trigger line 1
trigger line 2
Red to ignition +12V
Yellow to battery
Black to GND
Green to back car singal
Wire control
1
234 5
1) Non-Trigger/Reversing trigger state: Turn on/o screen | All other
states: Not used
2) Menu State: Parameter down
3) Non-Trigger State - Full screen display: Short press to enter "Menu setting" interface / Split Screen: Not used
Reversing Trigger State - Reversing: Short press to enter into "menu set-
TOUCH SCREEN
ting" interface / Long press to enter into "Grid Line" setting
WIRING
Left/Right Trigger State: Not Used
4) Menu State: Parameter Up
5) Non-Trigger State: Channel switch / Trigger state: Not used
10 11
Rear View Safety Reverse With Condence ™
Menu
9.9 feet
6.6 feet
3.3 feet
1.3 feet
BRIGHTNESS
Grid Lines
Generally, to help drivers estimate the distance from obstacles, there are
three lines for reference- red, yellow, and green. Those three lines are displayed on the monitor when car is reversing. The green line is 9.9 feet
50
from the back of the car and the yellow line is 6.6 feet away. The distant
red line is 3.3 from the backside of car while the closed red line is 1.3 feet
from the car. Both reference lines on the left and right should leave 0.65
In full display mode, short press menu to toggle options and use the
arrow keys to change parameters.
Wire Ctr Delay
This setting controls function of the wire control switch
1) If setting is o, the wire control switch functions the same as the CH
button
feet from the car.
9.9 feet
6.6 feet
GRID LINES
3.3 feet
MENU
2) If the setting is on the wire control switch changes the view, but the
view returns to previous state after delay time.
12 13
Rear View Safety Reverse With Condence ™
Adjustment
The accuracy of the grid lines can vary based on how you angle your camera. Therefore to compensate for inaccurancies, you can adjust the grid
lines.
Grid Lines
Reversing State: Long press "Menu" to enter guide
Screen Size 7.2" TFT-LCD Display
adjustment mode. We adjust left guide line rst.
Use the arrow keys to rotate the guid line counterclockwise and clockwise.
Short press "Guide Line Set" to switch to next
item. Adjust line with arrow keys. Press "Guide
Line Set" to adjust right grid line.
Right position Wrong Position
Counterclockwise Clockwise
Short Press: Next item
Longe press: save setting and exit
Left
Up Down
Short Press: Next item
Long Press: Save the setting and exit
Right
Aspect Resolution 1280 (H) X 390 (V)
Working Voltage DC10V-DC16V
Signal System PAL/AUTO/NTSC
Operating Temperature -20°C ~ +65°C
GRID LINES
Display on the monitor
SPECIFICATIONS
Mirror monitor with 7.2" dual display
Ultra reective - acts as mirror as well as monitor
4 Channel - can attach up to four cameras
Adjustable distance grid lines for backing up reference
Sleek frameless design
14 15
Rear View Safety Reverse With Condence ™
ONE YEAR WARRANTY
DISCLAIMER
REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A
PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR
REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC.
IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER
INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW
SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
THIS WARRANTY IS VOID IF: DEFECTS IN MATERIALS OR WORKMANSHIP OR DAMAGES
RESULT FROM REPAIRS OR ALTERATIONS WHICH HAVE BEEN MADE OR ATTEMPTED BY
OTHERS OR THE UNAUTHORIZED USE OF NONCONFORMING PARTS; THE DAMAGE IS DUE
TO NORMAL WEAR AND TEAR, THIS DAMAGE IS DUE TO ABUSE, IMPROPER MAINTENANCE,
NEGLECT OR ACCIDENT; OR THE DAMAGE IS DUE TO USE OF THE REAR VIEW SAFETY, INC.
SYSTEM AFTER PARTIAL FAILURE OR USE WITH IMPROPER ACCESSORIES.
WARRANTY PERFORMANCE
DURING THE ABOVE WARRANTY PERIOD, SHOULD YOUR REAR VIEW SAFETY PRODUCT
EXHIBIT A DEFECT IN MATERIAL OR WORKMANSHIP, SUCH DEFECT WILL BE REPAIRED WHEN
THE COMPLETE REAR VIEW SAFETY, INC. PRODUCT IS RETURNED, POSTAGE PREPAID AND
INSURED, TO REAR VIEW SAFETY, INC. OTHER THAN THE POSTAGE AND INSURANCE
REQUIREMENT, NO CHARGE WILL BE MADE FOR REPAIRS COVERED BY THIS WARRANTY.
REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE
USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE
WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL
AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC
LAWS AND MOTOR VEHICLE SAFETY REGULATIONS. THE REAR VIEW SAFETY PRODUCTS ARE
NOT A SUBSTITUTE FOR REARVIEW MIRRORS OR FOR ANY OTHER MOTOR VEHICLE
EQUIPMENT MANDATED BY LAW. OUR CAMERA SYSTEMS HAVE A LIMITED FIELD OF VISION
AND DO NOT PROVIDE A COMPREHENSIVE VIEW OF THE REAR OR SIDE AREA OF THE VEHICLE.
ALWAYS MAKE SURE TO LOOK AROUND YOUR VEHICLE AND USE YOUR MIRRORS TO CONFIRM
REARWARD CLEARANCE AND THAT YOUR VEHICLE CAN MANEUVER SAFELY. REAR VIEW
SAFETY AND/OR ITS AFFILIATES SHALL HAVE NO RESPONSIBILITY OR LIABILITY
FOR DAMAGE AND/OR INJURY RESULTING FROM ACCIDENTS OCCURRING WITH VEHICLES
HAVING SOME OF REAR VIEW SAFETY PRODUCTS INSTALLED AND REAR VIEW SAFETY AND/
OR ITS AFFILIATES, THE MANUFACTURER, DISTRIBUTOR AND SELLER SHALL NOT BE LIABLE
FOR ANY INJURY, LOSS OR DAMAGE, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OF THE
USE OR INTENDED USE OF THE PRODUCT. IN NO EVENT SHALL REAR VIEW SAFETY AND/OR
ITS AFFILIATES HAVE ANY LIABILITY FOR ANY LOSSES WHETHER DIRECT OR INDIRECT, IN
CONTRACT, TORT OR OTHERWISE INCURRED IN CONNECTION WITH THE SYSTEMS,
INCLUDING BUT NOT LIMITED TO DAMAGED PROPERTY, PERSONAL INJURY AND/OR LOSS OF
LIFE. NEITHER SHALL REAR VIEW SAFETY AND/OR ITS AFFILIATES HAVE ANY
DISCLAIMER
RESPONSIBILITY FOR ANY DECISION, ACTION OR INACTION TAKEN BY ANY PERSON IN
WARRANTY DISCLAIMERS
NO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THE ABOVE WARRANTY
IS MADE WITH REGARD TO THIS REAR VIEW SAFETY, INC. REAR VIEW SAFETY, INC. DISCLAIMS
RELIANCE ON REAR VIEW SAFETY SYSTEMS, OR FOR ANY DELAYS, INACCURACIES AND/OR
ERRORS IN CONNECTION WITH OUR SYSTEMS FUNCTIONS.
WARRANTY
ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR
PURPOSE AND ALL OTHER WARRANTIES IN NO EVENT SHALL REAR VIEW SAFETY. INC.
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A
CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING,
BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.
16 17
Rear View Safety Reverse With Condence ™
If you have any questions
about this product, contact:
Rear View Safety, Inc.
1797 Atlantic Avenue
Brooklyn, NY 11233
800.764.1028
Better Cameras. Better Service.
IT’S OUR GUARANTEE.
18
Rear View Safety
Loading...