RVS Systems RVS-655155 User Manual
Instruction Manual
Wireless Safety Camera System for Forklifts
with 5" Dual Screen Display
RVS-577FW
Reverse With Condence ™
1
TABLE OF CONTENTS
Introduction.............................. 03
Safety Information.............................. 04-06
Before Beginning Installation ....................... 07-08
System Features. . ........................... . . . 09
Monitor Introduction . . ...........................10-11
Remote Introduction...............................12
Triggers . . . . . ................. . . . . . . . 13-14
Menu.......................... . . . . 15-19
Pairing.......................... . . . . . 20
Monitor Specications . . ...........................21
Camera Specications . . ...........................22
Troubleshooting .................................23
Warranty ....................................24
Disclaimer ....................................25
2
Rear View Safety
NOTE!
Please read all of the installation instructions
carefully before installing the product. Improper
installation will void manufacturer’s warranty.
Congratulations on purchasing a Safety
Camera System!
With this manual you will be able to properly install and
operate the unit.
This system is intended to be installed as a
supplement aid to your standard rear view mirror that already exists
in your vehicle. The system should not be used as a substitute for the
standard rear view mirror or for any other mirror that exists in your
vehicle.
In some jurisdictions, it is unlawful for a person to drive a
motor vehicle equipped with a TV viewer or screen located forward of
the back of the driver’s seat or in any location that is visible, directly
or indirectly, to the driver while operating the vehicle.
INTRODUCTION
Reverse With Condence ™
3
Please read the entire manual and follow the instructions and
warnings carefully. Failure to do so can cause serious damage and/or
injury, including loss of life. Be sure to obey all applicable local
trac and motor vehicle regulations as it pertains to this product.
Improper installation will void manufacturer’s warranty.
USAGE:
• The system is designed to help the
driver safely detect people and/or
objects helping to avoid damage
or injury. However, you the driver, must use it properly. Use of this
system is not a substitute for safe,
proper or legal driving.
• Never back up while looking at the
monitor alone. You should always
check behind and around the vehicle when backing up, in the same
SAFETY INFORMATION
way as you would if the vehicle did
• The system is not intended for use
during extensive back-up maneuvers or backing into cross trac or
pedestrian walkways.
•Please, always remember, the area
displayed by the system is limited.
It does not display the entire panorama that is behind you.
not have the system. If you back up
while looking only at the monitor,
you may cause damage or injury.
Always back up slowly.
4
Rear View Safety
INSTALLATION:
• Electric shock or product
malfunction may occur if this
product is installed
incorrectly.
• Use this product within
the voltage range specied. Failure
to do so can cause
electronic shock or product
malfunction.
or disconnected wire may cause a
re.
• While installing the Rear View
System be careful with the wire
positioning in order to avoid wire
damage.
• The Rear View System should only
be used when the vehicle is in
reverse.
SAFETY INFORMATION
• Take special care when
cleaning the monitor.
• Make sure to rmly ax the prod-
uct before use.
• If smoke or a burning smell
is detected, disconnect the
system immediately.
• Where the power cable may touch
• Do not watch movies or
operate the monitor while driving;
as it may cause an
accident.
• Do not install the monitor
where it may obstruct drivers
view or obstruct an air bag
device.
a metal case, cover the cable with
friction tape. A short circuit
Reverse With Condence ™
• Dropping the unit may cause
possible mechanical failure.
5
If you have questions about this product, contact:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: 1.800.764.1028
IN NO EVENT SHALL SELLER OR MANUFACTURER BE
SAFETY INFORMATION
LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
6
Rear View Safety
Before drilling please check that no cable or wiring is on the other side
of the wall. Please clamp all wires securely to reduce the possibility
of them being damaged while vehicle is in use. Keep all cables away
from hot/moving parts and electrical noisy components.
We recommend doing a benchmark test before installation
to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in vehicle, when necessary a 0.8 (20mm)
hole should be drilled for passing camera cable through vehicles
walls. Install split grommets where applicable.
Step 3: Once all cables and wiring have been properly routed, perform
a system function test by temporarily connecting the system.
BEFORE YOU BEGIN
Reverse With Condence ™
7
Warning!
1. This monitor is high voltage. Only professionals should open the
monitor's case.
2. Do not watch the video while driving unless you are monitoring the
BEFORE YOU BEGIN
rear view camera display.
8
Rear View Safety
Loading...