Date Printed: 9/4/2014
Safety Data Sheet
* Trusted Quality Since 1921 *
www.rustoleum.com
1. Identification
Product Name: FLOOR PT 4PK 6000 ACTIVATOR Revision Date: 9/4/2014
Product Identifier: 6001604 Supercedes Date: New SDS
Product Use/Class: Activator/WB Epoxy
Page 1 / 6
Supplier:
Preparer: Regulatory Department
Emergency Telephone:
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, IL 60061
USA
24 Hour Hotline: 847-367-7700
Manufacturer:
Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, IL 60061
USA
2. Hazard Identification
EMERGENCY OVERVIEW: Causes skin burns. Causes skin irritation. Harmful if inhaled. Causes eye irritation. May cause eye,
skin, or respiratory tract irritation. KEEP OUT OF REACH OF CHILDREN. Use ventilation necessary to keep exposures below
recommended exposure limits, if any.
Classification
Symbol(s) of Product
Signal Word
Warning
GHS HAZARD STATEMENTS
Acute Toxicity, Dermal, category 5 H313 May be harmful in contact with skin.
Skin Irritation, category 2 H315 Causes skin irritation.
Aspiration Hazard, category 2 H305 May be harmful if swallowed and enters airways.
Skin Irritation, category 3 H316 Causes mild skin irritation.
Eye Irritation, category 2B H320 Causes eye irritation.
GHS PRECAUTIONARY STATEMENTS
P102 Keep out of reach of children.
P103 Read label before use.
P202 Do not handle until all safety precautions have been read and understood.
P234 Keep only in original container.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash … thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P271 Use only outdoors or in a well-ventilated area.
P273 Avoid release to the environment.
Date Printed: 9/4/2014
2807-30-9
50-00-0
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P281 Use personal protective equipment as required.
P285 In case of inadequate ventilation wear respiratory protection.
P312 Call a POISON CENTER or doctor/physician if you feel unwell.
P335 Brush off loose particles from skin.
P351 Rinse cautiously with water for several minutes.
P374 Fight fire with normal precautions from a reasonable distance.
P402 Store in a dry place.
P321 Specific treatment (see … on this label).
P352 Wash with plenty of soap and water.
P362 Take off contaminated clothing and wash before reuse.
P332+P313 If skin irritation occurs: Get medical advice/attention.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P302+P350 IF ON SKIN: Gently wash with plenty of soap and water.
3. Composition/Information On Ingredients
HAZARDOUS SUBSTANCES
Chemical Name CAS-No. Wt.%
Range
GHS Symbols
GHS Statements
Page 2 / 6
Ethylene Glycol Monopropyl Ether
Glacial Acetic Acid
Formaldehyde
The text for GHS Hazard Statements shown above (if any) is given in the "16. Other Information" section.
64-19-7
10-25
2.5-10
0.1-1.0
GHS02-GHS06
GHS02-GHS05-
GHS07
GHS02-GHS06
H226-311
H226-290-312-332
H226-302-311-330
4. First-aid Measures
FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical
attention. Do NOT allow rubbing of eyes or keeping eyes closed. If exposed to fumes or vapors, flush eyes with plenty of water for at
least 15 minutes. Get medical attention.
FIRST AID - SKIN CONTACT: Remove contaminated clothing. Wash skin with soap and water. Get medical attention. Wash
contaminated clothing and decontaminate footwear before reuse. Wash skin with soap and water. Remove contaminated clothing.
Get medical attention if irritation develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get
immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: If swallowed, do not induce vomiting. If victim is conscious and alert, give 2 to 4 cupfuls of water or milk.
Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. Treat
symptomatically and supportively. Swallowing less than an ounce will not cause significant harm. For larger amounts, do not induce
vomiting, but give one or two glasses of water to drink and get medical attention. If swallowed, rinse mouth with water. If feeling
unwell, get medical attention.
5. Fire-fighting Measures
EXTINGUISHING MEDIA:
UNUSUAL FIRE AND EXPLOSION HAZARDS: No unusual fire or explosion hazards noted. Keep containers tightly closed. FLASH
POINT IS TESTED TO BE GREATER THAN 200 DEGREES F.
SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent pressure buildup and possible
autoignition or explosion. Evacuate area and fight fire from a safe distance. Water may be used to cool closed containers to prevent
buildup of steam. If water is used, fog nozzles are preferred.
Alcohol Film Forming Foam, Dry Chemical, Water Fog
6. Accidental Release Measures
Date Printed: 9/4/2014
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Isolate the hazard area and deny entry to unnecessary and
unprotected personnel. Remove all sources of ignition, ventilate area and remove with inert absorbent and non-sparking tools.
Dispose of according to local, state (provincial) and federal regulations. Do not incinerate closed containers. If spilled, contain spilled
material and remove with inert absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with
local, state, and federal regulations. Do not incinerate closed containers
Page 3 / 6
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Use only in a well-ventilated area. Avoid contact with eyes, skin and clothing. Wash
hands before eating. Remove contaminated clothing and launder before reuse. Use only with adequate ventilation. Follow all
MSDS/label precautions even after container is emptied because it may retain product residues. Avoid breathing fumes, vapors, or
mist.
STORAGE: Keep container closed when not in use. Store in a dry, well ventilated place. Keep container tightly closed when not in
use.
8. Exposure Controls/Personal Protection
Chemical Name CAS-No.
Ethylene Glycol Monopropyl
Ether
Glacial Acetic Acid 64-19-7 5.0 10 ppm 15 ppm 10 ppm N.E.
Formaldehyde 50-00-0 1.0 N.E. N.E. 0.75 ppm N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve crossventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further information regarding personal
protective equipment and its application. Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
HYGIENIC PRACTICES: Wash thoroughly with soap and water before eating, drinking or smoking. Remove contaminated clothing
immediately and launder before reuse.
2807-30-9 20.0 25 ppm (Skin) N.E. N.E. N.E.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-TWA
OSHA PEL-
CEILING
9. Physical and Chemical Properties
Appearance:
Odor:
Relative Density:
Freeze Point, °C:
Solubility in Water:
Decompostion Temp., °C:
Boiling Range, °C:
Flammability:
Evaporation Rate:
Vapor Density:
Liquid
Slight Amine
1.042
ND
Miscible
No Information
212 - 350
Does not Support Combustion
Slower than Ether
Heavier than Air
Physical State:
Odor Threshold:
pH:
Viscosity:
Partition Coefficient, n-octanol/
water:
Explosive Limits, vol%:
Flash Point, °C:
Auto-ignition Temp., °C:
Vapor Pressure:
Liquid
N.E.
N.D.
N.D.
No Information
1.6 - 19.9
100
No Information
ND
(See "Other information" Section for abbreviation legend)
10. Stability and Reactivity
CONDITIONS TO AVOID: Avoid all possible sources of ignition. Avoid temperatures above 120 ° F. Avoid contact with strong acid
and strong bases.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids and strong alkalies.
HAZARDOUS DECOMPOSITION: When heated to decomposition, it emits acrid smoke and irritating fumes.
Date Printed: 9/4/2014
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
Page 4 / 6
11. Toxicological information
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes eye irritation. Irritating, and may injure eye tissue if not removed
promptly.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Causes skin irritation. Allergic reactions are possible. May cause skin
sensitization, an allergic reaction, which becomes evident upon re-exposure to this material. Low hazard for usual industrial handling
or commercial handling by trained personnel.
EFFECTS OF OVEREXPOSURE - INHALATION: Prolonged or excessive inhalation may cause respiratory tract irritation. High gas,
vapor, mist or dust concentrations may be harmful if inhaled. Avoid breathing fumes, spray, vapors, or mist.
EFFECTS OF OVEREXPOSURE - INGESTION: Substance may be harmful if swallowed.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS: Contains: Formaldehyde. Formaldehyde is classified as an OSHA
carcinogen, NTP class 2 carcinogen and an IARC class 2A carcinogen. Risk of cancer depends on duration and level of exposure,
and the actual concentration of formaldehyde in the formula. Effects of overexposure may include irritation of the nose and throat,
irritation of the digestive tract and signs of nervous system depression (e.g., headache, drowsiness, loss of coordination and fatigue).
Prolonged or repeated overexposure may cause lung damage.
PRIMARY ROUTE(S) OF ENTRY: Eye Contact, Ingestion, Inhalation, Skin Absorption, Skin Contact
ACUTE TOXICITY VALUES
The acute effects of this product have not been tested. Data on individual components are tabulated below:
CAS-No. Chemical Name Oral LD50 Dermal LD50 Vapor LC50
2807-30-9 Ethylene Glycol Monopropyl Ether N.I. 870 mg/kg Rabbit N.I.
64-19-7 Glacial Acetic Acid 3310 mg/kg Rat 1060 µL/kg Rabbit 11.4 mg/L Rat
50-00-0 Formaldehyde 500 mg/kg Rat 270 mg/kg Rabbit 0.578 mg/L Rat
N.I. - No Information
12. Ecological Information
ECOLOGICAL INFORMATION: Product is a mixture of listed components.
13. Disposal Information
DISPOSAL INFORMATION: Dispose of material in accordance to local, state, and federal regulations and ordinances. Do not allow
to enter waterways, wastewater, soil, storm drains or sewer systems.
14. Transport Information
Domestic (USDOT) International (IMDG) Air (IATA) TDG (Canada)
UN Number: N.A. NA NA N.A.
Proper Shipping Name: Not regulated Not regulated Not regulated Not regulated
Hazard Class: N.A. NA NA N.A.
Packing Group: N.A. NA NA N.A.
Limited Quantity: NA NA NA NA
15. Regulatory Information
Date Printed: 9/4/2014
U.S. Federal Regulations:
CERCLA - SARA Hazard Category
This product has been reviewed according to the EPA ‘Hazard Categories’ promulgated under Sections 311 and 312 of the
Superfund Amendment and Reauthorization Act of 1986 (SARA Title III) and is considered, under applicable definitions, to
meet the following categories:
Reactive Hazard, Acute Health Hazard, Chronic Health Hazard
Sara Section 313:
This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the
Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372:
Page 5 / 6
Chemical Name
Ethylene Glycol Monopropyl Ether 2807-30-9
Formaldehyde 50-00-0
CAS-No.
Toxic Substances Control Act:
This product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from
the United States:
No TSCA components exist in this product.
Inventory Information
Country Value
USA (TSCA) No Information
Canada (DSL) No Information
Mexico(INSQ) No Information
Europe (EINECS) No Information
Japan (ENCS) No Information
Philippines (PICCS) No Information
China (IECSC) No Information
Australia (AICS) No Information
Korea (KECI) No Information
New Zealand (NZIOC) No Information
No Information
CALIFORNIA PROPOSITION 65:
Warning: This products contains a substance known to the State of California to cause cancer.
Chemical Name
Formaldehyde
CAS-No.
50-00-0
CALIFORNIA PROPOSITION 65 REPRODUCTIVE TOXINS
Warning: This product contains a substance known to the State of California to cause birth defects or other reproductive
harm.
Chemical Name
Methanol
CAS-No.
67-56-1
International Regulations:
CANADIAN WHMIS:
This SDS has been prepared in compliance with Controlled Product Regulations except for the use of the 16 headings.
Date Printed: 9/4/2014
16. Other Information
HMIS RATINGS
Health: 3 Flammability: 1 Physical Hazard: 1 Personal Protection: X
CANADIAN WHMIS CLASS: D2B
NFPA RATINGS
Health: 3 Flammability: 1 Instability 0
Page 6 / 6
VOLATILE ORGANIC COMPOUNDS, g/L:
MSDS REVISION DATE:
REASON FOR REVISION:
Legend: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined
9/4/2014
No Information
357
Text for GHS Hazard Statements shown in Section 3 describing each ingredient:
H226 Flammable liquid and vapour.
H290 May be corrosive to metals.
H302 Harmful if swallowed.
H311 Toxic in contact with skin.
H312 Harmful in contact with skin.
H330 Fatal if inhaled.
H332 Harmful if inhaled.
Icons for GHS Pictograms shown in Section 3 describing each ingredient:
GHS02
GHS05
GHS06
GHS07
Rust-Oleum Corporation believes, to the best of its knowledge, information and belief, the information contained herein to be
accurate and reliable as of the date of this safety data sheet. However, because the conditions of handling, use, and storage of
these materials are beyond our control, we assume no responsibility or liability for personal injury or property damage incurred by
the use of these materials. Rust-Oleum Corporation makes no warranty, expressed or implied, regarding the accuracy or
reliability of the data or results obtained from their use. All materials may present unknown hazards and should be used with
caution. The information and recommendations in this material safety data sheet are offered for the users’ consideration and
examination. It is the responsibility of the user to determine the final suitability of this information and to comply with all applicable
international, federal, state, and local laws and regulations.
Loading...