Page 1
SaphIR
Bezel
Dust cove
r
862 Eye
Mini Infrared Receiver
Installation Manual
Bezel Exchange
The 862 Eye comes with three bezels (white, black, brass) for more installation
color choices.
To remove the bezel, hold the barrel steady and twist the bezel until it clears the
top of the barrel. Make sure the small clear dust cover stays in place at the end of
the barrel.
To replace the bezel, center the bezel over the dust cover and barrel, thread
onto the barrel end and twist until snug. The hole in the dust cover should line up
with the offset sensor at the top of the receiver.
Product Overview
The 862 Eye IR Receiver receives IR signals from a handheld IR remote control
and relays these signals to the audio-video equipment for operation from another
room. It mounts through a circular hole with a diameter of 0.5” (1.27 cm), requires
a minimum clearance of 2.0” (5.08 cm) behind the face of the mounting panel,
and will mount in a panel with a maximum thickness of 1.75” (4.45 cm).
The blue talkback LED can be disabled by snipping the wire that loops out of
the 860 near the leads.
Features
Comes with interchangeable white, black and brass bezels to easily customize
•
your installation
CFL friendly - allows installations in areas with compact fluorescent lighting.
•
Works in most lighting environments.
Blue IR confirmation LED
•
Option to disable talkback LED
•
Can easily be mounted in many in-wall speakers and custom cabinets
•
Wide band IR receives IR from many types of remotes
•
Disable IR talkback LED
NOTE: Disabling the talkback LED should be performed PRIOR to wiring the 862
to the connecting block.
To disable the blue talkback LED of the 862 Eye, locate the small wire loop at the
end of the receiver near the wire leads. Carefully snip the wire near the middle.
If it is necessary to re-enable the LED, simply reconnect the leads.
Limited Warranty
The Russound 862 IR Receiver is fully guaranteed for two (2) years from the date
of purchase against all defects in materials and workmanship. For this warranty
to apply, the unit must be installed and used according to its written instructions.
During this period, Russound will replace any defective parts and correct any
defect in workmanship without charge for either parts or labor. Accidental
damage and shipping damage are not considered defects under the terms of
this warranty. Russound assumes no responsibility for defects resulting from
abuse or servicing performed by an agency or person not specifically authorized
in writing by Russound. If service is necessary, it must be performed by Russound.
Damage to or destruction of components due to excessive power voids the
warranty. In these cases, the repair will be made at the owner’s expense. To
return for repairs, the unit must be shipped to Russound at the owner’s expense,
along with a note explaining the nature of the service required. Be sure to pack
in a corrugated container with at least 3 inches of resilient material to protect the
unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return
Authorization number. Write the RA number on the shipping label and ship to:
Russound, ATTN: Service, 5 Forbes Road, Newmarket NH 03857
Russound sells product only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound product
purchased from an unauthorized dealer or other source, including retailers, mail
order sellers and online sellers will not be honored or serviced under existing
Russound warranty policy. Any sale of products by an unauthorized source
or other manner not authorized by Russound shall void the warranty on the
applicable product.
5 Forbes Rd. Newmarket, NH 03857, USA
Tel 603.659.5170 • Fax 603.659.5388
email: tech@russound.com
28-1176 Rev. 2 08/29/08
Page 2
Mounting
surface
front
Mounting
surface
rear
Washer
Max thickness
1.75” (4.45 cm)
Min. clearance
2.0” (5.08 cm)
Barrel
Nu
t
Installation
Terminal
Strip
CAT-5e cable
Orange Pair
Open
Orange
Orange/White
Brow
n
Brown/Whit
e
Brown
Brown/Whit
e
Gree
n
Green/White
Gree
n
Green/White
Blue
Blue/White
Blue
Blue/White
Open
Drain Orange Pair
and Blue/White to
GND on 857
SIGNAL
(White
)
+12VDC
(Black)
GND
(Black)
857 IR
Co
nnecting Bloc
k
Connect to
846C or 1201A
power supply
1 2 3 4 5 6
IR R
ECEIVER IN
IR C
OMMON IN
IR CONFIRM
+12VDC
GND
ST
ATUS
SIGNAL
EMITTERS
S
TATUS
+
12VDC
P
OWER
+
12VDC
857 INFRARED
CONNECTING BLOC
K
862 Eye
SIGNAL (White)
+12VDC (Black)
GND (Black)
1 2 3 4 5 6
IR R
ECEIVER IN
IR C
OMMON IN
IR CONFIRM
+12VDC
GND
ST
ATUS
SIGNAL
EMITTERS
S
TATUS
+
12VDC
P
OWER
+
12VD
C
DESIGNED IN USA MADE IN KOREA
857 INFRARED
CONNECTING BLOCK
857 IR
Connecting Block
Connect to
846C or 1201A
power supply
The SaphIR 862 Eye is installed into a circular hole 0.5” in diameter. Remove the
nut from the receiver’s barrel. Insert the Eye (wire end first) until the bezel is flush
with the surface. Rethread the nut onto the barrel until it is snug against the rear
of the mounting surface. If necessary, use one or both of the included washers for
a more secure installation into soft or thin materials.
Wire Connections
Extended Leads from 862 Eye to Terminal Strip to Connecting Block
The extended connection between the IR receiver and the connecting block
should be made with twisted-pair wiring (i.e., CAT-5e cable). It may be necessary
to use shielded twisted-pair wiring if the wiring is exposed to interference from
power wiring centers or from broadcast signals (FM, TV, etc.) located nearby. The
installer should determine the cable type needed to suit the local conditions of
the installation. A terminal strip is included for extending the leads.
862 Eye CAT-5e 857
SIGNAL BL SIGNAL
+12VDC GR/GRW +12VDC
GND BR/BRW GND
OR/ORW GND
BLW GND
Wire Connections
Direct Connection from 862 Eye to Connecting Block
Connect the 862 Eye to the 857 connecting block. Connect GND (GROUND), IR
(SIGNAL) and Voltage (+12VDC) to connector on the 857.
Specifications
Receive Frequency: 36kHz to 58kHz
Transmit Frequency: 40kHz and 56kHz
Range: On Axis – 55ft to 80ft (16.8-24.4m)
30º Off Axis – 30ft to 55ft (9.1-16.8m)
Power: 12VDC 31mA max.
Dimensions: 0.46” Diameter x 2.03”D
(1.2cm Diameter x 5.16cm D)
Mounting Cord Length: 6.5 ft. (1.95m)
Loading...