Russound S2 User Manual

UNO-S2 Keypad

Installation Manual

SAFETY INFORMATION

UNO-S2 Keypad

2

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to.

4. Follow Instructions - All operating and user instructions should be followed.

5. Water and Moisture - The appliance should not be used near water; for example, near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.

6. Wall or ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

7. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventila­tion. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventila­tion openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through
the ventilation openings.

8. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appli­ances (including amplifiers) that produce heat.

9. Power Sources - The appliance should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.

10. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not
defeated.

11. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they
exit from the appliance.

12. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through the openings.

13. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: the power supply cord
or the plug has been damaged; or objects have fallen, liquid has been spilled into the appliance; or the appliance has
been exposed to rain; or the appliance does not appear to operate normally; or the appliance has been dropped or the
enclosure is damaged.

14. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All
other servicing should be referred to qualified service personnel.

Precautions:

1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
All models are designed for use with either AC120V, 60Hz or AC240, 50Hz voltages. The unit will autoswitch to either of
these voltages.

2. Do Not Touch The UNO-S2 With Wet Hands – Do not handle the unit or power cord when your hands are wet or damp. If
water or any other liquid enters the cabinet, take the UNO-S2 to a qualified service person for inspec

tion.

3. Care – Periodically wipe off the front and side panels of the cabinet with a soft cloth. Do not use rough material, thin­ners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering.

TABLE OF CONTENTS

UNO-S2 Keypad

3

Front Panel ..............................................................................................4-5

Operation ....................................................................................................6

User Menu ................................................................................................7-8

Settings ......................................................................................................9

Update Port ..............................................................................................10

Rear Panel ................................................................................................11

Keypad Connections..............................................................................12-13

Keypad Diagnostics Menu......................................................................14-15

Keypad Firmware Update ......................................................................16-17

Keypad Location ..................................................................................18-19

IR Receiver Connection ..............................................................................20

Technical Specifications..............................................................................21

Warranty ..............................................................................................22-23

USER GUIDE

UNO-S2 Keypad Front Panel

4

3

2

4

6

7

1

5

USER GUIDE

UNO-S2 Keypad Front Panel

5

LCD PANEL - 12-character backlit display shows status of the room, source,
volume, and more

SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the
CAV6.6/CAM6.6. Press and hold brings up the USER MENU for Loudness, Bass,
Treble, etc.

VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room

IR RECEIVER - Receives IR signals and passes them to the controller and source equip­ment. Also used when operating the UNO Keypad by using the SRC2 remote

COMMAND KEYS - Pressing the command keys controls the source equipment

POWER BUTTON - Turns room ON or OFF when pressed once, press and hold a
second time will turn on or off all CAV6.6/CAM6.6 rooms

F1 AND F2 BUTTONS - Selects Favorite 1 or Favorite 2 - preset user-selected
favorite settings per room

3

2

4

6

7

1

5

USER GUIDE

UNO-S2 Keypad Operation

6

MODE:

“DND”- Do Not Disturb
“SHARED”- Same source selected in multiple rooms
“SYS ON”- Indicates system on
“PARTY”- Party Mode enabled
“MASTER”- Master Keypad in Party Mode

12-character display

Volume Indicator

Indicates the middle of setting range

1

4

2 3

1

4

2

3

/
/

USER GUIDE

UNO-S2 Keypad User Menu

7

Zone On/Off

Press and release to turn on the UNO
System Keypad. This also turns on the cor­responding CAV6.6/CAM6.6’s room, and
any presets previously assigned will be
activated, including settings for bass, vol­ume, last source selected, etc. Press and
release to turn off the UNO System
Keypad. This will also put the correspon­ding CAV6.6/CAM6.6’s room into a stand­by state.

System All On/Off

An “All On” command is issued by pressing

and holding for 3 seconds, after an ini­tial room has been turned on. An “All Off”
command can be issued to all rooms by
pressing and holding after the room
has been turned off.

System On Indicator

When the room is off, but the system is on
in another room, is illuminated by a
green backlight and the "SYS ON" icon

remains visible.

Source Select Button

scrolls through the six A/V source
inputs and the Aux source. To change
sources, press and release . As the
sources are sequentially selected, each
source's name appears on the keypad LCD
panel. When a source is selected in more
than one room, the “SHARED” icon will
appear on all UNO Keypads using that
source. is also used to enter the User
Menu with a press and hold action. (See
next page for User Menu)

Volume Up/Down Buttons

The room’s audio output is adjusted using

F1 and F2 Buttons

The and buttons are user favorite
presets. These presets can be selected at
any time to recall source selection, vol­ume, favorite channel, disc, etc. To store a
favorite preset: first, adjust the room set­tings and select a source to be stored.

continued

USER GUIDE

UNO-S2 Keypad User Menu

8

Next, press and hold the desired or

button until SAVED is dis­played on the LCD panel. Now a press and
release of the button will recall the favorite
preset. To set a favorite numbered disc or
channel, use

or to select a disc or
channel (e.g., channel 45). Wait for the key­pad to show the source name, then press
and hold the F1 or F2 within 15 seconds of
setting the numeric selection to save the
setting.

Command Keys

The command keys allow control of the
selected source at the UNO Keypad. The
command keys are activated with a press
and release, or press and hold to access
secondary functions.

UNO-S2 User Menu

The User Menu allows the user to adjust
the audio properties and control functions
of a particular room.
The following keys are used to navigate
and make changes while using the User
Menu:

To enter the User Menu, press and hold

during normal operation.

To exit the User Menu, press and release .

Adjust feature setting (increment).

Adjust feature setting (decrement).

Go to next feature.

Go to previous feature.

View current feature setting.

The following features make up the User
Menu:

BASS TREBLE LOUDNESS

BALANCE TURN ON VOL BG

COLOR DO NOT DSTRB PARTY

MODE FRONT A/V IN