Russound CAV6.6-S2 User Manual
CAV6.6-S2 System
6-Zone, 6-Source
Audio/Video Controller Amplifier
INSTRUCTION MANUAL
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER - SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
POWER CORD NOTICE FOR INTERNATIONAL OPERATION
For 230V, 50Hz operation please select the power cord for your
area. Select the plug for your area at one end and a IEC320 connector at the other. It is not necessary to make any other
changes. If you have any questions please call Russound Inc. at
1-800-638-8055 or 603-659-5170
Safety Instructions:
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions
should be followed.
5. Water and Moisture - The appliance should not be
used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool.
6. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the manufacturer. An
appliance and cart combination should be moved with care. Quick
stops, excessive force and uneven surfaces may cause the appliance
and cart combination to overturn.
7. Wall or ceiling Mounting - The appliance should be mounted to a wall
or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.
11. Grounding or Polarization - Precaution should be taken so that the
grounding or polarization means of an appliance is not defeated.
12. Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, receptacles,
and the point where they exit from the appliance.
13. Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
14. Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
15. Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through the openings.
16. Damage Requiring Service - The appliance should be ser viced by qualified service personnel when:
A.The power supply cord or the plug has been damaged; or
B.Objects have fallen, liquid has been spilled into the appliance; or
C.The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally; or
E.The appliance has been dropped or the enclosure is damaged.
17. Servicing - The user should not attempt to ser vice the appliance beyond
that described in the operating instructions. All other servicing should
be referred to qualified service personnel.
Precautions:
1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
All models are designed for use with either AC120V, 60Hz or AC240,
50Hz voltages. The unit will autoswitch to either of these voltages
2. Do Not Touch The CAV6.6 With Wet Hands – Do not handle the CAV6.6
or power cord when your hands are wet or damp. If water or any other
liquid enters the CAV6.6 cabinet, take the CAV6.6 to a qualified service
person for inspection.
3. Location of CAV6.6 – Place the CAV6.6 in a well - ventilated location.
Take special care to provide plenty of ventilation on all sides of the
CAV6.6 especially when it is placed in an audio rack. If ventilation is
blocked, the CAV6.6 may overheat and malfunction. Do not expose the
CAV6.6 to direct sun light or heating units as the CAV6.6 internal components temperature may rise and shorten the life of the components.
Avoid damp and dusty places.
4. Care – From time to time you should wipe off the front and side panels
of the cabinet with a soft cloth. Do not use rough material, thinners,
alcohol or other chemical solvents or cloths since this may damage the
finish or remove the panel lettering.
IMPORTANT SAFEGUARDS
2
TABLE OF CONTENTS
3
USER SECTION
Product Introduction................................................................................................................6
Component Guide
CAV6.6 Controller.............................................................................................................7-8
UNO-S2 Keypad ..................................................................................................................9
UNO-LRC1 Remote Control ................................................................................................10
Operation
CAV6.6 Controller .............................................................................................................11
UNO-S2 Keypad............................................................................................................11-12
Setting Prefences
UNO-S2 User menu ...........................................................................................................13
INSTALLER SECTION
Getting Started
Unpacking ........................................................................................................................16
System Components.........................................................................................................16
Tools Needed....................................................................................................................16
System Installation Considerations......................................................................................16
Connection Tips................................................................................................................16
Wiring Instructions
Keypad Wiring ...................................................................................................................17
Speaker Wiring ................................................................................................................. 17
Component Guide
CAV6.6 Controller Front Panel.......................................................................................18-19
CAV6.6 Controller Rear Panel ........................................................................................20-21
UNO-S2 Keypad Front Panel...............................................................................................22
UNO-S2 Keypad Rear Panel ...............................................................................................23
UNO-S2 Keypad Installation
Keypad Location ...............................................................................................................24
Keypad Installation ............................................................................................................24
Keypad Connections ..........................................................................................................25
IR Receiver Connection......................................................................................................26
Making Connections
UNO-S2 Keypad Port Connection ........................................................................................27
Programming Center Keypad Port Connection.....................................................................28
Source Audio/Video Input Connections ...............................................................................29
Source Audio/Video Loop Output Connection......................................................................30
Speaker Connections ........................................................................................................31
4
TABLE OF CONTENTS
Accessory IR Connection...................................................................................................32
Zone Audio/Video Outputs .................................................................................................33
A-BUS Ready Sub-zone Connection.....................................................................................34
12VDC Trigger In/Out
Home Theater Trigger In................................................................................................35
50mA Trigger Out..........................................................................................................35
Page Trigger In/Out.......................................................................................................36
Page Audio/Video In .................................................................................................36-37
Zone Trigger Out...........................................................................................................38
R-NET Link In/Out..............................................................................................................39
RS-232 Interface...............................................................................................................40
Initial Install Test ................................................................................................................41
Programming
System Programming Overview.................................................................................42-43
Source Information Form................................................................................................44
Zone Information Form...................................................................................................45
Macro Editor Form ........................................................................................................46
Installation Menu...........................................................................................................47-58
Source Setup...........................................................................................................48-53
Basic Setup............................................................................................................48-49
Zone Setup ..............................................................................................................53-54
Controller Setup............................................................................................................54
Power Management..................................................................................................55-56
Learn IR........................................................................................................................57
Macro Editor ............................................................................................................57-58
System Info...................................................................................................................58
Setup Menu Flow Charts ...........................................................................................59-69
REFERENCE SECTION
Source Names List ...............................................................................................................71
Sample System Configurations
1 -Six Zones and Six Sources ........................................................................................72-73
2 - Integrate Multiple CAV6.6's ......................................................................................74-75
3 - Zone Expansion.......................................................................................................76-77
4 - A-BUS Ready Sub-zone Addition................................................................................78-79
5 - Additional Amplification ............................................................................................80-81
6 - Home Theater.........................................................................................................82-83
IR Code List.....................................................................................................................84-86
Technical Specifications.........................................................................................................87
Warranty ..............................................................................................................................88
5
USER SECTION
Component Guides
Explains front panel features of the CAV6.6 controller,
UNO-S2 keypad, and UNO-LRC1 remote control.
Operation
Step-by-step outline of the system's normal operation,
plus a look at adjustable features available through the User Menu.
I
N
P
U
T
M
U
TE
LA
ST
SLEEP
IN
FO
M
E
N
U
IN
PU
T
EN
TER
1
2
3
45
6
7
8
9
0
GUIDE
EX
IT
S
E
L
E
C
T
P
W
R
S
E
T
U
P
V
O
L
C
H
56
7
8
12
F1 F
2
3
4
UNO
VID
D
VD
TV
LOCAL SOURC
E
CONTROL
6
PRODUCT INTRODUCTION
Thank you for choosing the Russound®CAV6.6-S2 System to enhance your home with distributed
audio and video. This system’s state-of-the-art features and components blend seamlessly with your
unique lifestyle and preferences.
Besides distributing and controlling six A/V sources to six rooms (zones), your CAV6.6-S2 System
offers many features that increase your enjoyment of living. Here are several that you may find
particularly beneficial.
Favorites
The UNO
TM
-S2 keypad’s F1 and F2 buttons are preset favorites. These easy-to-set buttons make it
possible to hear your favorite radio station or watch your favorite satellite channel at just the
right volume in your room with just a button push. Want something new? Just re-save the Favorite
with a new choice.
Do Not Disturb
The Do Not Disturb mode prevents unwanted interruptions in your room and stops changes to your
selected A/V source. You may have a nursery or study that you want to keep quiet, or maybe you
are watching a DVD and don’t want it interrupted. Simply set the Do Not Disturb mode to “on” using
the User Menu, and be free from paging, Party Mode interaction and system-wide functions like “All
On” or “All Off.”
Party Mode
Ready to set the mood? In Party Mode, you just pick the source and the sound settings and hear the
music throughout all the rooms. The Master keypad simultaneously controls all the keypads in all the
rooms to effortlessly select or control the components. A great benefit of the Party Mode feature is
the ability to transfer the Master keypad mode to any keypad in the system. If the living room is the
center of the party, use that room’s keypad as Master. If the party moves to the sunroom and porch,
that room’s keypad can be set to Master instead.
Front (Aux) A/V In
This handy feature lets you easily hook up an additional temporary audio/video source through the
front of the controller. This way, your teenager can set up a game console when his friends come
over, and easily take it down without having to leave the games set up in the living room. Or your
family can watch the video camera playback of the holiday gathering while everyone is still there.
Here at Russound we are proud to continue providing innovative and intuitive A/V product solutions to
the world. When you link the industry-leading CAV6.6-S2 system with Russound’s commitment to its
products and customers, you have truly made – “the right connection.”
7
USER
COMPONENT GUIDE
CAV6.6 Controller-Front Panel
MAIN POWER SWITCH - Supplies power to the CAV6.6
REMOVABLE COVER LENS - Covers the connections on the front of the CAV6.6
ROOM LED ON/OFF INDICATORS - Indicates when a room is on (green) or off (red)
ROOM LABEL WINDOW - Holds the selected room Label (included)
AUX A/V LINE INPUTS - Supports connection of a seventh A/V source to the CAV6.6
AUX IR OUT PORT - Connects IR emitter for IR control of the Aux A/V source component
1
4
2
5
3
2
31 4
5
6
6
8
Front A/V Aux Connections
The Aux Input is located to the right of the power
switch on the front panel. Connect the Left,
Right, and Video Input Connectors to the source
component using quality RCA signal cables.
The Aux IR jack adjacent to the line input
accepts an IR Emitter with a 1/8” plug (e.g.,
Russound 845.1 IR emitter). The emitter’s other
end attaches to the IR window of the component
to control the auxiliary source.
USER
COMPONENT GUIDE
CAV6.6 Controller-Front Panel
9
LCD PANEL - 12-character backlit display shows status of the room, source,
volume, and more
SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the
CAV6.6. Press and hold brings up the USER MENU for loudness, bass, treble, etc.
VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room
IR RECEIVER - Receives IR signals and passes them to the controller and source
equipment. Also used when operating the UNO Keypad by using the UNO-LRC1 remote
COMMAND KEYS - Pressing the command keys controls the source equipment
POWER BUTTON - Turns room ON or OFF when pressed once, press and hold a
second time will turn on or off all CAV6.6 rooms
F1 AND F2 BUTTONS - Selects Favorite 1 or Favorite 2 - preset user-selected
favorite settings per room
1
4
7
2
5
3
6
3
2
4
6
7
1
5
USER
COMPONENT GUIDE
UNO-S2 Keypad-Front Panel
10
USER
COMPONENT GUIDE
UNO-LRC1 Remote Control
LOCAL DEVICE BUTTONS - Select local
source to be controlled by UNO-LRC1.
SETUP - Use for programming UNO-LRC1 using
the built-in library or by learning-in codes.
UNO SOURCE BUTTON - Selects UNO
Keypad for control by UNO-LRC1.
ROOM ON/OFF - Turns room on and off while
in the UNO mode.
NUMBER BUTTONS - Buttons (0-9) for direct
selection of channels or tracks.
INPUT - Scrolls through sources connected
to the CAV6.6 while in the UNO mode.
COMMAND KEYS - Control the VCR, DVD, or
CD player with these buttons.
INPUT - Directly select A/V sources connected
to the CAV6.6 while in the UNO mode.
F1 AND F2 BUTTONS - Selects Favorite 1 or
Favorite 2 preset selections.
CURSOR KEYS - Issues IR commands for
source equipment, allowing movement
through menus and program screens.
VOLUME UP/DOWN - Raises and lowers the
volume for the room you are in.
1
4
4
7
7
2
5
8
3
3
6
9
11
10
6
9
1
2
5
8
10
11
11
Main Power and Zone Status
The power switch for the CAV6.6 controller is
"on" in the up position. Any active room is indicated on the front of the controller by a green
backlit label, which shows red when the room is
inactive. In most basic installations, all functions
and room settings are controlled through the
corresponding UNO Systems Keypads.
USER
OPERATION
CAV6.6 Controller
UNO-S2 Keypad
MODE:
“DND”- Do Not Disturb
“SHARED”- Same source selected in multiple rooms
“SYS-ON”- Indicates system on
“PARTY”- Party Mode enabled
“MASTER”- Master Keypad in Party
Mode
12-character display
Volume Indicator
Indicates the middle of setting range
1
4
2
3
1
4
2 3
12
Zone On/Off
Press and release to turn on the UNO
System Keypad. This also turns on the corresponding CAV6.6’s room, and any presets previously assigned will be activated, including settings for bass, volume, last source selected,
etc. Press and release to turn off the UNO
System Keypad. This will also put the corresponding
CAV6.6’s room into a standby state.
System All On/Off
An “All On” command is issued by pressing
and holding for 3 seconds, after an initial room
has been turned on. An “All Off” command can
be issued to all rooms by pressing and holding
after the room has been turned off.
System On Indicator
When the room is off, but the system is on in
another room, is illuminated by a green
backlight and the "SYS ON" icon remains visible.
Source Select Button
scrolls through the six A/V source inputs
and the Aux source. To change sources, press
and release . As the sources are sequentially
selected, each source's name appears on the
keypad LCD panel. When a source is selected in
more than one room, the “SHARED” icon will
appear on all UNO Keypads using that source.
is also used to enter the User Menu with a
press and hold action. (See next page for User
Menu)
Volume Up/Down Buttons
The room’s audio output is adjusted using .
F1 and F2 Buttons
The and buttons are user favorite presets. These presets can be selected at any time
to recall source selection, volume, and favorite
channel, disk, etc. To store a favorite preset: first,
adjust the room settings and select a source to be
stored. Next, press and hold the desired or
button until SAVED is displayed on the LCD
panel. Now a press and release of the button will
recall the favorite preset. To set a favorite numbered disk or channel, use
or to select a
disk or channel (e.g., channel 45). Wait for the
keypad to show the source name, then press
and hold the F1 or F2 within 15 seconds of setting the numeric selection to save the setting.
Command Keys
The command keys allow control of the selected
source at the UNO Keypad. The command keys are
activated with a press and release, or press and
hold to access secondary functions.
USER
NORMAL OPERATION
UNO-S2 Keypad
13
The User Menu allows the user to adjust the
audio properties and control functions of a particular room.
The following keys are used to navigate and
make changes while using the User Menu:
To enter the User Menu, press and hold
during normal operation. To exit the User Menu,
press and release .
Adjust feature setting (increment).
Adjust feature setting (decrement).
Go to next feature.
Go to previous feature.
View current feature setting.
The following features make up the User Menu:
BASS TREBLE LOUDNESS BALANCE
TURN ON VOL BG COLOR DO NOT
DSTRB PARTY MODE FRONT A/V IN
Feature and Setting:
1. BASS
-10 < Bass:Flat > +10
2. TREBLE
-10 < Treble:Flat > +10
3. LOUDNESS (more bass, fuller sound)
On or Off
4. BALANCE
Left -10 < Center > Right +10
5. TURN ON VOL (default room volume level)
0 to 100
6. BG COLOR (keypad background light)
Amber or Green or Off
7. DO NOT DSTRB - On or Off (default)
Do Not Disturb means do not disturb this room
or selected source. This stops pages from
being sent to this room, stops an “All Off," "All
On" or Party Mode command from affecting this
room.
When another UNO Systems Keypad selects the
same source, a DND icon will appear alerting
the user the source is in Do Not Disturb mode.
8. PARTY MODE - Master (Enable) or Off (Disable)
When in “PARTY MODE” the system is primarily
controlled by a “MASTER” keypad. Party Mode
links all rooms to the same source which is
selected by the Master Keypad room. Any keypad in the system can become a Master keypad
(if enabled) but only one Master Keypad may
exist at a time in Party Mode. Selecting Master
keypad mode from another keypad will transfer
Master keypad control to that room and release
it from the first. When the source selected in the
Master keypad room is changed then the source
for all rooms changes as well.
Volume level changes at the Master Keypad will
be reflected in all rooms in Party Mode. NonMaster zones in Party Mode can temporarily override Master Keypad volume level adjustments for
their particular room preference. F1 and F2
favorite presets selected from the Master Keypad
will be enabled in all rooms in Party Mode. Master
Keypad will not change Bass, Treble, or Loudness
adjustments for any other rooms other than the
Master Keypad room. Every other keypad will still
operate its respective bass, treble, balance and
loudness adjustments for that room.
9. FRONT (AUX) A/V IN - Enabled or Disabled
Allows the system to select a seventh source option
through the controller's front panel AUX connection
for use with camcorders, game consoles, etc.
USER
USER MENU SETTINGS
UNO-S2 User Menu Operation
14
INSTALLER SECTION
Getting Star
ted
Includes an installation overview, including tools needed and wiring instructions.
Component Guides
Reviews front and back panel features of the CAV6.6 controller and the UNO-S2 keypad.
Keypad Installation
Explains UNO-S2 keypad installation and wiring.
Making Connections
Details front and back panel connections of the controller and the keypad.
System Installation Overview
Outlines the programming planning process, and includes information forms to complete prior to
programming.
Installation Menu
Explains the programming menus that set up controller, keypad, source, and zone operations.
Setup Menu Flow Char
ts
Presents the programming menus in a graphical flow chart format.
15
INSTALLER
Do not connect the controller's main power feed until all other connections have been
made and verified. Live connection or removal of the keypad wiring or other wiring
when the system is powered can cause communication problems in the network.
Double-check terminations during each phase of the installation to prevent accidental
damage. Incorrect wiring is the number one cause for non-warranty product damage.
CAUTION
16
INSTALLER
GETTING STARTED
Unpacking the System Components
• Keep the original carton and packing materials
for future shipment or storage.
• Check for any visible signs of damage. If
you encounter any concealed damage, consult your Russound dealer before proceeding
to install the unit.
• Retain the sales receipt as it establishes the
duration of the limited warranty and provides
information for insurance purposes.
CAV6.6-S2 System Components:
• 1 (one) CAV6.6 Controller/Amplifier
• 6 (six) UNO-S2 System Control Keypads
• 1 (one) UNO-LRC1 Learning/Preprogrammed
Remote Control
• 6 (six) 845.1 Micro Emitters
Tools needed for installation:
• Drill with a 1/2” x 6” drill bit
• Keyhole saw
• Flat head screwdriver (medium size)
• Phillips Screwdriver (cordless recommended)
• 110 punchdown tool (included)
• Modular RJ-45 crimper and connectors
• Pair of diagonal cutters or wire strippers
• Stud finder
• Steel wire fish tape
• Cable staples
• Double-gang electrical work boxes
System Installation Considerations
There are several factors to consider before
installing the Russound CAV6.6-S2 system:
• What are the intended listening zones, and
what zones require audio and video distribution
or audio only?
• Are A-BUS
®
sub-zones needed? A-BUS subzones are only available for zones 1 - 4. The AKP2 amplified keypad can provide direct source
selection for only the first four sources when in
‘Multi’ source mode.
• What system options and accessories might
be required for features such as paging, local
sources, etc.?
• From where in each zone will the user prefer
to control the system? Where will the keypads
be located? Where will the speakers be located?
• Where will the source equipment be located?
The CAV6.6 must have proper ventilation above
and below for air circulation and heat dissipation.
A rack-mount location may require fans and vents.
Connection Tips
• It is recommended that the CAV6.6 and the
source equipment be plugged into a dedicated
20-amp circuit with an isolated ground. A power
line conditioner can reduce interference problems caused by noise found in some electrical
systems.
• Disconnect all live power cords before making
connections to the controller.
• Verify that all connections and polarity are
correct.
• Keep all power cords away from all signal
cables to prevent humming from induced noise.
• Choose reliable signal cables/patch cords.
• Label all wires with room location at both ends
of the wire.
17
INSTALLER
WIRING INSTRUCTIONS
RJ-45 Connections
The CAT-5 T568A wiring standard shown on the right is used
for the RJ-45 terminations.
Keypad Wiring
For the UNO-S2 keypad, the following connections are used to terminate the CAT-5 wire to the
110 punchdown on the keypad:
CA
T-5 WIRE COLOR TYPE
Brown . . . . . . . . . . . . . . . . . . . +12V
Brown/White . . . . . . . . . . . . . . +12V
Green . . . . . . . . . . . . . . . . . . Ground
Green/White. . . . . . . . . . . . Status In
Orange . . . . . . . . . . . . . . . . . Ground
Orange/White. . . . . . . . . . . . . IR Out
Blue . . . . . . . . . . . . . . . . . . . COM A
Blue/White . . . . . . . . . . . . . . COM B
• To determine the amount of CAT 5 wire
required for the system installation, first
decide how many keypads will be used, then
determine the distance between each intended keypad location to the intended CAV6.6
location. The maximum recommended wire
run length is 250 feet for each UNO-S2
Keypad.
• Make sure that the entire wire path
between keypads and CAV6.6 is clear and
not obstructed by a floor ceiling joist, or
masonry wall which can’t be drilled through.
• Confirm ahead of time that you can drill an
outlet hole easily and in an unobtrusive spot
to connect wires with the CAV6.6.
• Label wires with keypad and room location.
This simplifies CAV6.6 hook-up once the keypads and speakers are installed.
• If you plan to use an additional IR receiver
with an UNO-S2 keypad, first determine the
location of the IR receiver, then measure the
distance from the intended location to the
UNO-S2 keypad location. Incorporating
optional IR receivers will require additional
wire. Consult the selected IR receiver
model’s manual for the specific wire needs.
Speaker Wiring
• Standard 16-gauge 4-conductor stranded
speaker wire can be run up to to 125 feet;
14-gauge wire can be run up to 250 feet.
• When running wire, pay particular attention
to the following areas:
• Avoid locations concealing pipes, heating
ducts and AC wiring in the general vicinity.
• Avoid running wires close to house electrical wiring for any distance. If you have to run
them parallel, make sure to space the wires
at least two feet from the AC line.
18
INSTALLER
COMPONENT GUIDE
CAV6.6 Controller-Front Panel
1
7
2 5
8
3
6
9
10
11
4
19
INSTALLER
COMPONENT GUIDE
CAV6.6 Controller-Front Panel
PROGRAM SELECTOR COVER - Protects the Program Selector Switch
KEYPAD PROGRAMMING PORT - Accepts an RJ-45 terminated UNO keypad to
program certain features of the CAV6.6
FRONT/REAR RS-232 SWITCH - Selects front or rear RS-232 connection for optional
PC connection during programming
RS-232 INTERFACE - The RS-232 Interface on the front and on the rear, allows the
zones to be controlled by PC or other devices that have an RS-232 Interface.
The RS-232 Interface also allows for software updates
IR CONFIRMATION LED - IR Learning and preprogrammed IR output confirmation LED.
IR RECEIVER - Receives IR signal when learning IR codes into the CAV6.6
ZONE LABEL - Selectable backlit labels identify active zones
OS PROGRAM SELECTOR SWITCH - Selects between Main and Aux Micro-controller IC
when updating the CAV6.6 OS software.
MAIN LED - IIlluminates when the Main Micro-Controller IC is selected to be
programmed
AUX LED - Illuminates when the AUX IC is selected to be programmed
RESET BUTTON - Resets the CAV6.6 when OS updates are completed
1
4
7
2
5
8
9
3
6
10
11
20
17 16 14 12131519 1821 20
ZONE 12VDC TRIGGER OUT - 12VDC 50ma is available whenever the corresponding
zone is turned on
UNO KEYPAD PORTS - One UNO Keypad Port for each of the six CAV6.6 Zones
24VDC 2.5A INPUT - Provides power to the A-BUS READY SUB-ZONES when used
with a 24VDC 2.5A power supply (e.g., Russound A-PS)
ZONE AUDIO/VIDEO OUTPUTS - Variable line audio with fixed video, used to connect
to an external amplifier and television monitor
AUDIO/VIDEO SOURCE LOOP OUTPUTS - Six sets of buffered Audio/Video Line Level
Loop Output connections
AC 240V-AC 110V Switch - Switches A/C input Voltage between 110VAC and
240VAC
AC 120/240 INPUT - Grounded 3-terminal plug detachable power cord connection
for the CAV6.6
FUSE HOLDER - Holds a replaceable fuse for A/C input connection
110VAC operation-F 3A H 250V, 240VAC operation-F 1.25A H 250V
SOURCE IR OUTPUTS - Six routed source-specific IR Output jacks allow for IR control
of source equipment
4
7
2
5
8
3
6
9
1
41 3 6
9 711
INSTALLER
COMPONENT GUIDE
CAV6.6 Controller-Rear Panel
10
52
8
21
SPEAKER OUTPUTS - Connect 8 Ohm speakers for each zone by using detachable
color-coded modular snap connectors
AUDIO/VIDEO INPUTS - Six sets of Audio/Video Line Level input connections for
CAV6.6 source components
ACC IR OUTPUT - ACC IR Output jack will pass all IR signals from all keypads
PAGE LINE LEVEL AUDIO GAIN CONTROL - Adjusts the Line Level Audio Page Input
PAGE A/V INPUTS - RCA jacks allow for one Audio/V ideo Page Input. Signal sensing
is used on Page Audio In to initiate a page
PAGE 12VDC TRIGGER OUT - Page Trigger Out supplies 12VDC whenever 12VDC is
applied to the Page 12VDC Trigger In
PAGE 12VDC TRIGGER IN - Applying 12VDC to the Page 12VDC Trigger In jack will
activate Audio/Video Page for assigned CAV6.6 Zones and initiate a page (overrides
signal sense)
HOME THEATER 12VDC TRIGGER IN - 12VDC input jack notifies the CAV6.6 that
additional A/V components are active, e.g., home theater equipment
12VDC TRIGGER OUT - 12VDC 50ma Trigger Out turns on when any zone is on
A-BUS READY SUB-ZONES - A-BUS Amplified Control Modules and Hubs can be added
for additional sub-zones of audio (Zones 1 to 4 only)
R-NET LINK IN AND LINK OUT - Links multiple CAV6.6’s, also links future Russound
components that are R-NET compatible
RS-232 INTERFACE - The RS-232 Interface on the rear and on the front, allows the
zones to be controlled by PC or other devices that have an RS-232 Interface. The
RS-232 Interface also allows for software updates and programming
20
21
19
18
17
16
15
14
13
12
10
11
INSTALLER
COMPONENT GUIDE
CAV6.6 Controller-Rear Panel
22
INSTALLER
COMPONENT GUIDE
UNO-S2 Keypad-Front Panel
SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad
OS UPDATE PORT - Port used for UNO keypad OS software updates
1
2
1
2
DATA
DATA
GND
N/C
+12VDC
RS-232
23
EXTERNAL IR RECEIVER IN CONNECTOR - Connection for an external IR Receiver.
OS UPDATE JUMPER - Selects “Run” or “OS Update” mode.
RESET BUTTON - Reset whenever changing from RUN to OS update
110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the
UNO-S2 Keypad and the CAV6.6 controller.
1
2
3
4
2
3
1
4
INSTALLER
COMPONENT GUIDE
UNO-S2 Keypad-Rear Panel
24
INSTALLER
UNO-S2 KEYPAD-INSTALLATION
Keypad Location
The best infrared remote performance is achieved
with the keypad away from any direct sunlight,
plasma TV, and low voltage lighting controls. Also
consider convenience when choosing a location.
Choose a place that is easily seen from the position where a person is most likely to be located.
Check whether or not you can route the wire to
the location you have chosen.
Keypad Installation
To install a double-gang keypad, you will need to
use a UL/CSA approved plastic double-gang
electrical box.
Route CAT-5 wire to the junction box from the
CAV6.6.
Use the supplied 110 punchdown tool to connect each wire to its corresponding color
labeled on the punchdown terminal.
Ensure jumper settings on keypads are in the
run positions.
Mount the keypad in the electrical box and
attach the cover plate. Repeat the steps until all
keypads are installed.
Plastic Double-Gang
Electrical Box
UNO-S2
Back Plate
Screw
Screw
Screwless
Cover Plate
CAT-5 Connection
The UNO-S2 Keypad uses a 110-punchdown
terminal to provide a simple installation and
strong connection for CAT-5 cable’s eight conductors. Punchdown terminals require the use of
a punchdown tool which has been provided with
the keypad kit. Attach the CAT-5 cable to the
110-punchdown terminal on the UNO-S2 Keypad
as shown, matching the conductor colors to the
connection color guide. The keypad will not
operate properly if the terminations deviate from
the required connection order.
Caution:
Take care when using an impact 110 punchdown
tool, as this may overspread the contact points.
Use of the impact tool may propel stray bits of wire
and jacket into the keypad’s chassis and possibly
cause a short in the circuitry. Gently shake or blow
air through the keypad chassis to remove stray wire
before the keypad is installed into the junction box.
OS Update Port
The OS Update Port is is used to update the
UNO-S2 Keypad operating system software in
the future. When an update is released, it will be
available online through the Document Center at
www.russound.com.
Look for the Technical
Documents under Multi-source/Multi-room products. The programming cable is available from
Russound, Part #2500-120633.
Jumper Setting
The jumper settings on the back of the UNO-S2
Keypad can be set for “Run” and “OS Update.” The
jumper setting must be in the “Run” position before
the keypad is mounted into the junction box, and
must remain set in “Run” to operate the keypad.
The jumper will be set to “OS Update” only while
updating the keypad’s operating systems.
25
INSTALLER
UNO-S2 KEYPAD-INSTALLATION
UNO-S2 Keypad Connections
Punchdown Tool
CAT-5 Connections (back of keypad)
Jumper Setting (back of keypad)
OS Update Port (front of keypad)
Punchdown Tool
26
The UNO-S2 keypad has an External IR Receiver
In terminal for connecting an external IR receiver
such as the Russound 858, SaphIR Eye, or
SaphIR Phantom. Use 2 twisted pair wire with
one pair connecting GND (GROUND) and IR (SIGNAL) and the other pair connecting ST (STATUS)
and V+ (+12VDC). If the wire has a shield, connect it to ground at the UNO-S2 only.
Back of
Russound 858
Back of
UNO-S2
INSTALLER
UNO-S2 KEYPAD-INSTALLATION
IR Receiver Connection
27
The UNO System Keypad Ports are located on
the back of the CAV6.6 in the top left corner.
Connections made at the UNO Keypad Ports are
made using CAT-5 T568A RJ-45 wire configuration. CAT-5 is color-coded for ease of installation. For a clean installation when wiring from an
UNO System Keypad Port use an RJ-45 CAT-5
patch cable to connect from the keypad port to
an RJ-45 Wall Plate (optional). Using the same
CAT-5 T568A RJ-45 wiring configuration, use
CAT-5 from the RJ-45 Wall Plate to the keypad.
If using more than one keypad on a zone, connect a SA-ZX3 UNO System Keypad Splitter
(optional) directly to the UNO System Keypad
Port instead of going through the wall plate.
Always use the CAT-5 T568A RJ-45 wire configuration when wiring any of the UNO System
Keypad Ports.
(See Sample System Configuration 3, page 76)
INSTALLER
MAKING CONNECTIONS
UNO System Keypad Port Connection
28
The CAV6.6 can be programmed via keypad connection using CAT-5 and the T568A RJ-45 wire configuration. An UNO-S2 Keypad can be attached to the controller at the Programming Center Keypad
Port Connection.
INSTALLER
MAKING CONNECTIONS
Programming Center Keypad Port Connection
Loading...