Page 1
CAM6.6X-S1/S2 System
6-Zone, 6-Source
XM Receiver and UNO Smart Keypads
INSTRUCTION MANUAL
Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER - SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
POWER CORD NOTICE FOR INTERNATIONAL OPERATION
For 230V, 50Hz operation please select the power cord for your
area. Select the plug for your area at one end and a IEC320 connector at the other. It is not necessary to make any other
changes. If you have any questions please call Russound Inc. at
1-800-638-8055 or 603-659-5170
Safety Instructions:
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance in the operating instruc-
tions should be adhered to.
4. Follow Instructions - All operating and user instructions should be fol-
lowed.
5. Water and Moisture - The appliance should not be
used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool.
6. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the manufacturer. An appliance and cart combination should be moved with
care. Quick stops, excessive force and uneven surfaces may cause the
appliance and cart combination to overturn.
7. Wall or ceiling Mounting - The appliance should be mounted to a wall
or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10.Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.
11.Grounding or Polarization - Precaution should be taken so that the
grounding or polarization means of an appliance is not defeated.
12.Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, receptacles,
and the point where they exit from the appliance.
13.Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
14.Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
15.Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through the openings.
16.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally; or
E. The appliance has been dropped or the enclosure is damaged.
17.Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should
be referred to qualified service personnel.
Precautions:
1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
All models are designed for use with either AC120V, 60Hz or AC240,
50Hz voltages. The unit will autoswitch to either of these voltages
2. Do Not Touch The Unit With Wet Hands – Do not handle the CAM6.6 or
power cord when your hands are wet or damp. If water or any other liquid enters the CAM6.6 cabinet, take the CAM6.6 to a qualified service
person for inspection.
3. Location of CAM6.6 – Place the CAM6.6 in a well - ventilated location.
Take special care to provide plenty of ventilation on all sides of the
CAM6.6 especially when it is placed in an audio rack. If ventilation is
blocked, the CAM6.6 may overheat and malfunction. Do not expose the
CAM6.6 to direct sun light or heating units as the CAM6.6 internal components temperature may rise and shorten the life of the components.
Avoid damp and dusty places.
4. Care – From time to time you should wipe off the front and side panels
of the cabinet with a soft cloth. Do not use rough material, thinners,
alcohol or other chemical solvents or cloths since this may damage the
finish or remove the panel lettering.
This device complies with Part 15B of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Russound could
void the user’s authority to operate this equipment.
IMPORTANT SAFEGUARDS
2
Page 3
TABLE OF CONTENTS
3
USER SECTION
Product Introduction ............................................................................................................6
Component Guide
CAM6.6 Controller...............................................................................................................7
UNO-S1 Keypad ..................................................................................................................8
UNO-S2 Keypad .................................................................................................................9
UNO-LRC1 Remote Control ................................................................................................10
UNO-S1 Keypad Operation .................................................................................................11
UNO-S1 User Menu ...........................................................................................................12
UNO-S2 Keypad Operation .................................................................................................13
UNO-S2 User Menu ...........................................................................................................14
Internal Source - XM Tuner
XM Radio Activation...........................................................................................................15
XM Radio Display ..............................................................................................................15
XM Radio Modes .........................................................................................................16-19
UNO-S1 Keypad Control.....................................................................................................20
UNO-S2 Keypad Control ...............................................................................................21-22
UNO-LRC1 Remote Control ...........................................................................................23-24
INSTALLER SECTION
Getting Started
Unpacking ........................................................................................................................26
System Components .........................................................................................................26
Tools Needed....................................................................................................................26
System Installation Considerations......................................................................................26
Connection Tips ................................................................................................................26
Wiring Instructions
Keypad Wiring...................................................................................................................27
Speaker Wiring .................................................................................................................27
Component Guide
CAM6.6 Controller Rear Panel .......................................................................................28-29
UNO-S1 Keypad Front Panel...............................................................................................30
UNO-S1 Keypad Rear Panel ...............................................................................................31
UNO-S2 Keypad Front Panel...............................................................................................32
UNO-S2 Keypad Rear Panel ...............................................................................................33
Keypad Installation
UNO-S1 Keypad Location and Installation ............................................................................34
UNO-S2 Keypad Location and Installation ............................................................................35
Page 4
4
TABLE OF CONTENTS
Making Connections
UNO Keypad Port Connections...........................................................................................36
Source Audio Input Connections.........................................................................................37
Source IR Input Connections ..............................................................................................37
Common IR Input Connection .............................................................................................38
Speaker Connections ........................................................................................................39
Zone Fixed/Variable Audio Output.......................................................................................40
12VDC Home Theater Trigger In/Out ..................................................................................41
12VDC Mute Trigger In/Out................................................................................................42
RNET Link In/Out...............................................................................................................43
RS-232 Interface ...............................................................................................................44
Optional Internal Source
XM Radio Antenna ........................................................................................................45
XM Signal Strength.......................................................................................................45
Initial Install Test................................................................................................................46
Programming
System Programming Overview .................................................................................47-48
Source Information Form................................................................................................49
Zone Information Form...................................................................................................50
Macro Editor Form ........................................................................................................51
Installation Menu
Installation Menu Overview .............................................................................................52
Peripheral Setup .......................................................................................................53-55
Source Setup ...........................................................................................................55-61
Basic Setup............................................................................................................55-56
Zone Setup ..............................................................................................................61-62
Controller Setup ............................................................................................................62
Power Management ..................................................................................................62-64
Learn IR ...................................................................................................................64-65
Macro Editor ............................................................................................................65-66
System Info...................................................................................................................66
Setup Menu Flow Charts ...........................................................................................67-79
REFERENCE SECTION
IR Device Code List ..........................................................................................................80-82
IR Keycode List ..............................................................................................................83-104
Source Names .............................................................................................................105-106
Sample Configurations..................................................................................................107-110
Technical Specifications.......................................................................................................111
Warranty ............................................................................................................................112
All trademarks are the property of their respective owners.
Page 5
5
USER SECTION
Component Guides
Explains front panel features of the CAM6.6 controller,
UNO-S1 keypad, UNO-S2 keypad and UNO-LRC1 remote control.
Operation
Step-by-step outline of the system's normal operation,
plus a look at adjustable features available through the User Menu.
IN
P
U
T
M
UTE
LA
ST
SLEEP
IN
F
O
MENU
IN
PU
T
EN
TER
1
2
3
4
5
6
7
8
9
0
GUIDE
E
X
I
T
S
E
L
E
C
T
P
W
R
S
E
T
U
P
V
O
L
C
H
5
6
7
8
1
2
F1 F
2
3
4
UN
O
V
ID
DVD TV
LOCAL SOURCE
CONTROL
Page 6
6
PRODUCT INTRODUCTION
Thank you for choosing the Russound®CAM6.6X-S1/S2 System to enhance your home with distributed audio. It combines the CAM6.6 Controller Amplifier and UNO keypads into a state-of-the-art
home audio system that blends seamlessly with your unique lifestyle and preferences.
Besides distributing and controlling six audio sources to six rooms (zones), your CAM6.6X-S1/S2
System offers many features that increase your enjoyment of living. Here are several that you may
find particularly beneficial.
Internal Source
The CAM6.6X Controller Amplifier includes an optional internal source - an XM satellite radio module.
XM satellite radio provides over 100 channels of music, news sports, comedy, talk and entertainment. Its coast-to-coast coverage, digital quality sound and commercial-free music channels make XM
radio the choice for the discriminating listener.
XM radio is a subscription-based service, and listeners can subscribe by visiting XM on the web
www.xmradio.com
or by calling XM’s Listener Care at 800-852-9696.
The XM tuner module can store up to 36 favorites, or memory presets. These are stored in groups
of six called banks, and there are six banks. Each preset and each bank can be given a custom name
of your choice.
Favorites
The UNO-LRC1 remote and the UNO-S2 keypad’s F1 and F2 buttons are preset favorites. These easyto-set buttons make it possible to hear your favorite radio station or watch your favorite satellite
channel at just the right volume in your room with just a button push. Want something new? Just resave the Favorite with a new choice.
Do Not Disturb
The Do Not Disturb mode prevents unwanted interruptions in your room and stops changes to your
selected audio source. You may have a nursery or study that you want to keep quiet, or maybe you
are watching a DVD and don’t want it interrupted. Simply set the Do Not Disturb mode to “on” using
the User Menu, and be free from Party Mode interaction and system-wide functions like “All On” or
“All Off.”
Party Mode
Ready to set the mood? In Party Mode, you just pick the source and the sound settings and hear the
music throughout all the rooms. The Master keypad simultaneously controls all the keypads in all the
rooms to effortlessly select or control the components. A great benefit of the Party Mode feature is
the ability to transfer the Master keypad mode to any keypad in the system. If the living room is the
center of the party, use that room’s keypad as Master. If the party moves to the sunroom and porch,
that room’s keypad can be set to Master instead.
Here at Russound we are proud to continue providing innovative and intuitive audio product solutions
to the world. When you link the industry-leading CAM6.6X-S1/S2 system with Russound’s commitment
to its products and customers, you have truly made – “the right connection.”
Page 7
7
USER
COMPONENT GUIDE
CAM6.6 Controller-Front Panel
MAIN POWER SWITCH - Supplies power to the CAM6.6
ROOM LED ON/OFF INDICATORS - Indicates when a room is on (green) or off (red)
1
2
2
1
Main Power and Zone Status
The power switch for the CAM6.6 controller is "on" in the up position. Any active
room is indicated on the front of the controller by a green LED, which shows red
when the room is inactive. In most basic installations, all functions and room settings are controlled through the corresponding UNO Systems Keypads.
Page 8
8
USER
COMPONENT GUIDE
UNO-S1 Keypad-Front Panel
LCD PANEL - 5-character backlit display shows status of the room, source,
volume, and more
SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the
CAM6.6. Press and hold brings up the USER MENU for loudness, bass, treble, etc.
VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room
IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when operating the UNO Keypad by using the UNO-LRC1 remote
POWER BUTTON - Turns room ON or OFF when pressed once, press and hold a second time will turn on or off all CAM6.6 rooms
COMMAND KEYS - Pressing the command keys controls the source equipment
1
4
2
5
3
6
1
2
3
4
5
6
Blues
(press)
(press and hold)
(press)
(press and hold)
Page 9
9
LCD PANEL - 12-character backlit display shows status of the room, source,
volume, and more
SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the
CAM6.6. Press and hold brings up the USER MENU for loudness, bass, treble, etc.
VOLUME UP/DOWN BUTTONS - Raises and lowers the volume for the room
IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when operating the UNO Keypad by using the UNO-LRC1 remote
COMMAND KEYS - Pressing the command keys controls the source equipment
POWER BUTTON - Turns room ON or OFF when pressed once, press and hold a second time will turn on or off all CAM6.6 rooms
F1 AND F2 BUTTONS - Selects Favorite 1 or Favorite 2 - preset user-selected
favorite settings per room
1
4
7
2
5
3
6
3
2
4
6
7
1
5
USER
COMPONENT GUIDE
UNO-S2 Keypad-Front Panel
CD PLAYER 1
Page 10
10
USER
COMPONENT GUIDE
UNO-LRC1 Remote Control
LOCAL DEVICE BUTTONS - Select local
source to be controlled by UNO-LRC1.
SETUP - Use for programming UNO-LRC1 using
the built-in library or by learning-in codes.
UNO SOURCE BUTTON - Selects UNO
Keypad for control by UNO-LRC1.
ROOM ON/OFF - Turns room on and off while
in the UNO mode.
NUMBER BUTTONS - Buttons (0-9) for direct
selection of channels or tracks.
INPUT - Scrolls through sources connected
to the CAM6.6 while in the UNO mode.
COMMAND KEYS - Control the source (tuner,
CD player, etc.) with these buttons.
INPUT - Directly select audio sources connected to the CAM6.6 while in the UNO mode.
F1 AND F2 BUTTONS - Selects Favorite 1 or
Favorite 2 preset selections.
CURSOR KEYS - Issues IR commands for
source equipment, allowing movement
through menus and program screens.
VOLUME UP/DOWN - Raises and lowers the
volume for the room you are in.
1
4
4
7
7
2
5
8
3
3
6
9
11
10
6
9
1
2
5
8
10
11
Page 11
11
USER
OPERATION
UNO-S1 Keypad
Zone On/Off
Press and release to turn on the UNO
System Keypad. This also turns on the corre-
sponding CAM6.6’s room, and any presets previ-
ously assigned will be activated, including set-
tings for bass, volume, last source selected,
etc. Press and release to turn off the UNO
System Keypad. This will also put the corresponding
CAM6.6’s room into a standby state.
System All On/Off
An “All On” command is issued by pressing
and holding for 3 seconds, after an initial room
has been turned on. An “All Off” command can
be issued to all rooms by pressing and holding
after the room has been turned off.
System On Indicator
When the room is off, but the system is on in
another room, is illuminated by a green
backlight and the "SYS ON" icon remains visible.
Source Select Button
scrolls through the audio source inputs. To
change sources, press and release . As the
sources are sequentially selected, each source's
name appears on the keypad LCD panel. When
a source is selected in more than one room, the
“SHARED” icon will appear on all UNO Keypads
using that source. is also used to enter the
User Menu with a press and hold action. (See
next page for User Menu)
Volume Up/Down Buttons
The room’s audio output is adjusted using .
Command Keys
The command keys allow control of the
selected source at the UNO Keypad. The command
keys are activated with a press and release, or
press and hold to access secondary functions.
Page 12
12
USER
USER MENU SETTINGS
UNO-S1 User Menu Operation
The User Menu allows the user to adjust the
audio properties and control functions of a particular room.
To enter or exit the User Menu, press and hold
during normal operation. The following keys
are used to navigate and make changes while
using the User Menu:
Press and hold to adjust feature setting
(increment)
Press and hold to adjust feature setting
(decrement)
Go to next feature.
Go to previous feature.
View current feature setting.
Note: When within the UNO-S1 User Menu, if no
keys are pressed, the display will revert back to
its runtime display.
UNO-S1 User Menu
The following features make up the User Menu:
Bass Treb Loud Bal OnVol
Bkgnd DND Party
Feature and Setting:
1. Bass -10 < Bass:Flat > +10
2. Treb (Treble) -10 < Treble:Flat > +10
3. Loud (Loudness) (more bass, fuller sound)
On or Off
4. Bal (Balance) Left 10 < Center > Right 10
5. OnVol (Turn on Volume) (default room volume
level) 0 to 100 (in steps of 2)
6. Bkgnd (Background Color) (keypad background light) Amber or Green or Off
7. DND (Do Not Disturb) - On or Off (default)
Do Not Disturb means do not disturb this room or
selected source. This stops pages from being
sent to this room, stops an “All Off," "All On" or
Party Mode command from affecting this room.
When another UNO Systems Keypad selects the
same source, a DND message will scroll on the
the LCD panel, alerting the user the source is in
Do Not Disturb mode.
8. Party (Party Mode) - Master or Off
When in “PARTY MODE” the system is primarily
controlled by a “MASTER” Keypad. Party Mode
links all rooms to the same source which is
selected by the Master Keypad room. Any keypad
in the system can become a Master Keypad (if
enabled) but only one Master Keypad may exist at
a time in Party Mode. Selecting Master Keypad
mode from another keypad will transfer Master
Keypad control to that room and release it from
the first. When the source selected in the Master
Keypad room is changed then the source for all
rooms changes as well. The keypad will scroll a
PARTY message on the LCD panel. It will scroll a
MASTR message in lieu of PARTY if Master is
enabled.
Volume level changes at the Master Keypad will
be reflected in all rooms in Party Mode. NonMaster zones in Party Mode can temporarily override Master Keypad volume level adjustments for
their particular room preference. Master Keypad
will not change Bass, Treble, or Loudness adjustments for any other rooms other than the Master
Keypad room. Every other keypad will still operate
its respective bass, treble, balance and loudness
adjustments for that room.
Page 13
USER
OPERATION
UNO-S2 Keypad
13
Zone On/Off
Press and release to turn on the UNO
System Keypad. This also turns on the corre-
sponding CAM6.6’s room, and any presets previ-
ously assigned will be activated, including set-
tings for bass, volume, last source selected,
etc. Press and release to turn off the UNO
System Keypad. This will also put the corresponding
CAM6.6’s room into a standby state.
System All On/Off
An “All On” command is issued by pressing
and holding for 3 seconds, after an initial room
has been turned on. An “All Off” command can
be issued to all rooms by pressing and holding
after the room has been turned off.
System On Indicator
When the room is off, but the system is on in
another room, is illuminated by a green
backlight and the "SYS ON" icon remains visible.
Source Select Button
scrolls through the six A/V source inputs. To
change sources, press and release . As the
sources are sequentially selected, each source's
name appears on the keypad LCD panel. When
a source is selected in more than one room, the
“SHARED” icon will appear on all UNO Keypads
using that source.
is also used to enter the User Menu with a
press and hold action. (See next page for User
Menu)
Volume Up/Down Buttons
The room’s audio output is adjusted using .
F1 and F2 Buttons
The and buttons are user favorite pre-
sets. These presets can be selected at any time
to recall source selection, volume, and favorite
channel, disk, etc. To store a favorite preset: first,
adjust the room settings and select a source to be
stored. Next, press and hold the desired or
button until SAVED is displayed on the LCD
panel. Now a press and release of the button will
recall the favorite preset. To set a favorite num-
bered disk or channel, use
or to select a
disk or channel (e.g., channel 45). Wait for the
keypad to show the source name, then press
and hold the F1 or F2 within 15 seconds of set-
ting the numeric selection to save the setting.
Command Keys
The command keys allow control of the selected
source at the UNO Keypad. The command keys are
activated with a press and release, or press and
hold to access secondary functions.
Page 14
14
The User Menu allows the user to adjust the
audio properties and control functions of a particular room.
The following keys are used to navigate and
make changes while using the User Menu:
To enter the User Menu, press and hold
during normal operation. To exit the User Menu,
press and release .
Adjust feature setting (increment).
Adjust feature setting (decrement).
Go to next feature.
Go to previous feature.
View current feature setting.
Note: When within the UNO-S2 User Menu, if no
keys are pressed, the display will revert back to
its runtime display.
The following features make up the User Menu:
BASS TREBLE LOUDNESS BALANCE
TURN ON VOL BG COLOR DO NOT
DSTRB PARTY MODE
Feature and Setting:
1. BASS
-10 < Bass:Flat > +10
2. TREBLE
-10 < Treble:Flat > +10
3. LOUDNESS (more bass, fuller sound)
On or Off
4. BALANCE
Left -10 < Center > Right +10
5. TURN ON VOL (default room volume level)
0 to 100
6. BG COLOR (keypad background light)
Amber or Green or Off
7. DO NOT DSTRB - On or Off (default)
Do Not Disturb means do not disturb this room
or selected source. This stops pages from
being sent to this room, stops an “All Off," "All
On" or Party Mode command from affecting this
room.
When another UNO Systems Keypad selects the
same source, a DND icon will appear alerting
the user the source is in Do Not Disturb mode.
8. PARTY MODE - Master (Enable) or Off (Disable)
When in “PARTY MODE” the system is primarily
controlled by a “MASTER” keypad. Party Mode
links all rooms to the same source which is
selected by the Master Keypad room. Any keypad in the system can become a Master keypad
(if enabled) but only one Master Keypad may
exist at a time in Party Mode. Selecting Master
keypad mode from another keypad will transfer
Master keypad control to that room and release
it from the first. When the source selected in the
Master keypad room is changed then the source
for all rooms changes as well.
Volume level changes at the Master Keypad will
be reflected in all rooms in Party Mode. NonMaster zones in Party Mode can temporarily override Master Keypad volume level adjustments for
their particular room preference. F1 and F2
favorite presets selected from the Master Keypad
will be enabled in all rooms in Party Mode. Master
Keypad will not change Bass, Treble, or Loudness
adjustments for any other rooms other than the
Master Keypad room. Every other keypad will still
operate its respective bass, treble, balance and
loudness adjustments for that room.
USER
USER MENU SETTINGS
UNO-S2 User Menu Operation
Page 15
15
XM Radio Activation
XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depending on location) transferred by terrestrial antennas. The radio is a subscription-based service with a
monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but
will not broadcast the full range of channels without activation. Activation and billing are handled solely through XM Radio.
To activate the XM tuner:
1. Turn on the power, select the XM Tuner source, and select channel 0. The tuner’s eight-character
XM satellite Radio ID number will appear on the display. Write the number down to have it
available when contacting XM Radio for activation. The number is also shown on the back of the
unit and on the product box.
2. To subscribe, have a major credit card and your XM Radio ID number at hand and contact XM at
http://www.xmradio.com/activation You can also activate service by calling XM Radio at
1-800-852-9696. You will be guided through the activation process step by step.
3. A complete and up-to-date full channel listing is available on the XM Radio website,
www.xmradio.com.
XM Radio Displays
In addition to Channel and Category information, the XM tuner will broadcast operating condition messages when the following conditions occur:
Display Condition
ANTENNA Antenna not connected
UPDATING Updating encryption code
LOADING Acquiring channel audio or information
OFF AIR Channel not in service
CH- - - Channel (SID) no longer available
- - - - - - Corresponding Artist Name or Song Title are null (empty)
- - - - - - No channel available for the chosen category
USER
INTERNAL SOURCE - XM TUNER
XM Radio Overview
Page 16
16
XM Radio Modes
There are four user “modes” for selecting music on the XM Tuner:
Preset (default or normal)
Category Search
Now Playing
Display Preferences.
These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing EXIT and return to tuner display and Preset mode.
For all XM Modes
The chart below outlines the button presses for various XM tuner functions
outside
of the XM modes.
If the UNO-S1 button operation is not specifically mentioned, use the UNO-LRC1 to
transmit commands through the UNO-S1.
Operating Mode Toggle
This button press accesses the three XM modes. The three modes will appear in order: Category
Search, Now Playing and Display Preferences.
Exit Current Mode
This button press returns the XM tuner to Preset (default) mode.
Signal Strength
This button press and hold accesses the Signal Strength mode. Depending on the signal, the following will be displayed:
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL Loss of signal
Press the appropriate button again to exit Signal Strength Mode.
UNO-S1 UNO-S2 UNO-LRC1
All User Modes
Operating Mode Toggle
Exit Current Mode
Signal Strength
Hold Hold
USER
INTERNAL SOURCE - XM TUNER
XM Radio Modes
Page 17
17
Preset (default) Mode
This is the normal operating mode of the XM tuner for channel up and down, bank selection and
memory presets.
Next Preset
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.
Previous Preset
This button press accesses the previous saved preset in the chosen bank
Next Bank
This button press accesses the next bank (total of 6 banks).
Previous Bank
This button press accesses the previous bank.
Channel Up
This button press accesses the next active channel up from the current channel.
Channel Down
This button press accesses the next active channel down from the current channel.
UNO-S1 UNO-S2 UNO-LRC1
Preset Mode
Next Preset
Previous Preset
Next Bank
Hold Hold
Previous Bank
Hold Hold
Channel Up
Hold
Channel Down
Hold
USER
INTERNAL SOURCE - XM TUNER
XM Radio Modes
Page 18
18
Category Search Mode (
11..CCAATT SSEEAARRCCHH
)
XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is
a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this
mode is refined to scrolling only those channels in the selected category.
Next Category
This button press accesses the next category from the current category.
Previous Category
This button press accesses the previous category from the current category.
Category Channel Up
This button press accesses the next channel up within the selected category.
Category Channel Down
This button press accesses the next channel down within the selected category.
UNO-S1 UNO-S2 UNO-LRC1
Category Search Mode
Next Category
Previous Category
Category Channel Up
Hold
Category Channel Down
Hold
USER
INTERNAL SOURCE - XM TUNER
XM Radio Modes
Page 19
19
Now Playing Mode (
22..NNOOWW PPLLAAYYNNGG
)
This mode displays information about the current XM selection. Appropriate button presses access
the next or previous information item.
NNAAMMEE::
Displays the artist’s name, feature name or program name (news, talk, sports).
TTIITTLLEE::
Displays the song title or program title.
CCAATTEEGGOORRYY::
Displays the current category.
UNO-S1 UNO-S2 UNO-LRC1
Now Playing Mode
Next Info Item
Previous Info Item
Display Preference Mode (
33..DDSSPPLLYY PPRREEFF
)
This mode allows you to choose how XM channel information will be displayed on the keypad and
tuner. Appropriate button presses access the next or previous preference item.
Note: For any display configuration, the artist’s name and song title will scroll before the display
returns to the designated display format.
Channel Number (
CCHH NNUUMMBBEERR::
)
This selection displays the channel number only (e.g., XM070, XM103).
Channel Name (
CCHH NNAAMMEE::
)
This selection displays the channel name only (e.g., ESPN Radio, Real Jazz).
Channel Number and Name (
##::CCHH NNAAMMEE::
)
This selection displays the channel number and name (e.g., 64:The Groove, 121:Fox News).
UNO-S1 UNO-S2 UNO-LRC1
Display Preference Mode
Next Display Preference
Previous Display Preference
USER
INTERNAL SOURCE - XM TUNER
XM Radio Modes
Page 20
20
UNO-S1 Keypad Control of Tuner
Selecting the tuner
On the UNO-S2 keypad, press to select the
XM Tuner by choosing the tuner’s preassigned
source number (1).
Selecting the desired channel
Press and hold and to activate manual
channel selection. Once active, press or
to scroll through channels. The channel will
scroll twice on the keypad then stop and display
the channel display format’s first five characters.
If an XM radio tuner operation does not
specifically refer to an UNO-S1 button
operation, use the UNO-LRC1 remote control to transmit commands through the
UNO-S1.
USER
INTERNAL SOURCE - XM TUNER
UNO-S1 Keypad Control
TUNER SELECTION - Select
source number assigned to
XM Tuner (1)
CHANNEL SELECTION Scrolls through channels
(press and hold, then
press)
1
2
1
2
Blues
Page 21
21
USER
INTERNAL SOURCE - XM TUNER
UNO-S2 Keypad Control
UNO-S2 Keypad Contr
ol of Tuner
Selecting the tuner
On the UNO-S2 keypad, press to select the
XM Tuner by choosing the tuner’s preassigned
source number (1).
Selecting a Mode
Push to toggle between XM modes.
Exiting a Mode
Press to exit XM mode selection menu.
Selecting the desired channel
Use and for manual channel selection.
The channel will appear on the keypad. To move
quickly through the channels, press and hold
either or for more than 1.5 seconds.
Signal Strength Mode
To check XM signal strength, press and hold
then release. The display shows the signal
strength rating. To exit, press again.
Selecting a Bank
To select a bank, press and hold for bank
up or for bank down. The bank’s name will
be temporarily displayed on the UNO-S2.
Recalling a Memory Preset
Press and to scroll through the memo-
ry presets for the selected bank. This procedure
will step through all of the presets in the current
bank, then loop back to start at the first one.
Only configured presets will be displayed.
Mute
Press to mute/unmute the tuner audio output.
Page 22
22
TUNER SELECTION - Select source number
assigned to XM TUNER (1)
TUNE UP/DOWN - Used for manual channel
selection
SELECT - XM operating mode toggle
SEEK - (press) Exit current XM mode
SCAN - (press and hold) XM Signal Strength mode
toggle
MUTE - Mutes/unmutes tuner audio output
BANK SELECT - Used for bank selection (press
and hold)
MEM UP/DOWN - Scrolls through memory preset
stations (press)
1
4
2
5
3
1
2
4
4
5
6
6
6
3
USER
INTERNAL SOURCE - XM TUNER
UNO-S2 Keypad Control
XM Classics
Page 23
23
USER
INTERNAL SOURCE - XM TUNER
UNO-LRC1 Remote Control
UNO-LRC1 Remote Control of Tuner
Selecting the tuner
To select the XM tuner, push and choose
the source number preassigned to the XM Tuner
(1), or use the UNO numeric source inputs at
the bottom of the UNO-LRC1.
Selecting a Mode
Push , or to toggle between
XM operating modes.
Exiting a Mode
Press or to exit XM operating mode
menu.
Signal Strength mode
Press and hold and release. The display
shows the signal strength rating. To exit press
.
Selecting the desired channel
Use the Channel and or and
for manual tuning. To move quickly
through the channels, press and hold the button
for more than 1.5 seconds. To directly select a
channel, enter the one-, two- or three-digit chan-
nel.
Recall Last Channel
Press the button to recall the last channel
selected.
Selecting a Bank
To select a bank, press and hold for bank
up or for bank down.
Setting a Memory Preset
To set a memory preset, tune to the desired
channel, then press and hold the appropriate
number key (1-6) for the preset. When the mem-
ory preset is saved, the appropriate preset num-
ber (M1 through M6) and SAVED will be tem-
porarily displayed on the UNO-S2.
Recalling a Memory Preset
Press and to scroll through a loop
of all the memory presets for the currently
selected bank. Only configured presets will be
displayed.
Mute
Press the button to mute/unmute the
tuner audio output.
Page 24
24
POWER - Power managed by CAM6.6
NUMERIC INPUT - Number buttons for direct
input of channel, preset, bank (press). Memory
preset save (press and hold)
TUNE UP/DOWN - Incrementally scrolls through
channels
EXIT - Exit XM operating mode
TUNE UP/DOWN - Incrementally scrolls through
channels
SELECT - XM Operating mode toggle
MENU - XM Operating mode toggle
PLAY - XM Operating mode toggle
BANK UP/DOWN - Used for bank selection (press
and hold)
MEM UP/DOWN - Scrolls through memory presets for selected bank (press)
MUTE - Mutes/unmutes tuner audio output
SCAN - Exit XM Operating mode
TUNER SELECTION - Select source number
assigned to XM Tuner (1)
INFO - XM Now Playing mode toggle
SEEK UP/DOWN - Next/previous preset,
category, info item, display preference
GUIDE - XM Category Search mode toggle
LAST - Recalls last XM channel selected
1
4
7
2
5
8
3
6
9
11
10
5
7
10
13
6
14
9
15
1
2
4
12
3
12
UNO SELECTION - UNO must be the
selected source for control of the
CAM6.6 and any connected components. Select UNO before sending
UNO-LRC1 remote commands.
5
8
9
11
12
13
14
15
USER
INTERNAL SOURCE - XM TUNER
UNO-LRC1 Remote Control
16
16
Page 25
25
INSTALLER SECTION
Getting Started
Includes an installation overview, including tools needed and wiring instructions.
Component Guides
Reviews front and back panel features of the CAM6.6 controller and the UNO-S1 and UNO-S2
keypads.
Keypad Installation
Explains UNO-S1 and UNO-S2 keypad installation and wiring.
Making Connections
Details front and back panel connections of the controller and the keypad.
System Programming Overview
Outlines the programming planning process, and includes information forms to complete prior to
programming.
Installation Menu
Explains the programming menus that set up controller, keypad, source and zone operations.
Setup Menu Flow Char
ts
Presents the programming menus in a graphical flow chart format.
IR Device Codes
A list of controller’s IR device code library for source Device Code entries.
Key Function Codes
A list of IR codes for each command type contained in the built-in library.
Sour
ce Names
A list of Source Names available for assignment.
Sample Configurations
Diagrams of various configurations using CAM6.6s and other components.
Page 26
26
INSTALLER
GETTING STARTED
Unpacking the System Components
• Keep the original carton and packing materials
for future shipment or storage.
• Check for any visible signs of damage. If you
encounter any concealed damage, consult your
Russound dealer before proceeding to install the
unit.
• Retain the sales receipt as it establishes the
duration of the limited warranty and provides
information for insurance purposes.
CAM6.6X-S1/S2 System Components:
• 1 (one) CAM6.6 Controller/Amplifier
• 1 (one) UNO-S2 System Control Keypad
• 5 (five) UNO-S1 System Control Keypads
• 1 (one) UNO-LRC1 Learning/Preprogrammed
Remote Control
• 6 (six) 845.1 Micro Emitters
Tools needed for installation:
• Drill with a 1/2” x 6” drill bit
• Keyhole saw
• Flat head screwdriver (medium size)
• Phillips Screwdriver (cordless recommended)
• 110 punchdown tool (included)
• Modular RJ-45 crimper and connectors
• Pair of diagonal cutters or wire strippers
• Stud finder
• Steel wire fish tape
• Cable staples
• Double-gang electrical work box
• Single-gang electrical work boxes
System Installation Considerations
There are several factors to consider before
installing the Russound CAM6.6X-S1/S2 system:
• What are the intended listening zones?
• What system options and accessories might
be required for features such as local sources,
etc.?
• From where in each zone will the user prefer
to control the system? Where will the keypads
be located? Where will the speakers be located?
• Where will the source equipment be located?
The CAM6.6 must have proper ventilation above
and below for air circulation and heat dissipation.
A rack-mount location may require fans and vents.
Connection Tips
• It is recommended that the CAM6.6 and the
source equipment be plugged into a dedicated
20-amp circuit with an isolated ground. A power
line conditioner can reduce interference problems caused by noise found in some electrical
systems.
• Disconnect all live power cords before making
connections to the controller.
• Verify that all connections and polarity are
correct.
• Keep all power cords away from all signal
cables to prevent humming from induced noise.
• Choose reliable signal cables/patch cords.
• Label all wires with room location at both ends
of the wire.
Page 27
INSTALLER
WIRING INSTRUCTIONS
RJ-45 Connections
The CAT-5 T568A wiring standard shown on the
right is used for the RJ-45 terminations.
Keypad Wiring
For the UNO-S2 and UNO-S1 keypad, the following connections are used to terminate the CAT-5
wire to the 110 punchdown on the keypad:
CA
T-5 WIRE COLOR TYPE
Brown . . . . . . . . . . . . . . . . . . . +12V
Brown/White . . . . . . . . . . . . . . +12V
Green . . . . . . . . . . . . . . . . . . Ground
Green/White . . . . . . . . . . . . Status In
Orange . . . . . . . . . . . . . . . . . Ground
Orange/White. . . . . . . . . . . . . IR Out
Blue . . . . . . . . . . . . . . . . . . . COM A
Blue/White . . . . . . . . . . . . . . COM B
• To determine the amount of CAT-5 wire
required for the system installation, first
decide how many keypads will be used, then
determine the distance between each intended keypad location to the intended CAM6.6
location. The maximum recommended wire
run length is 250 feet for each UNO Keypad.
• Make sure that the entire wire path
between keypads and CAM6.6 is clear and
not obstructed by a floor ceiling joist, or
masonry wall which can’t be drilled through.
• Confirm ahead of time that you can drill an
outlet hole easily and in an unobtrusive spot
to connect wires with the CAM6.6.
• Label wires with keypad and room location.
This simplifies CAM6.6 hook-up once the keypads and speakers are installed.
Speaker Wiring
• Standard 16-gauge 4-conductor stranded
speaker wire can be run up to to 125 feet;
14-gauge wire can be run up to 250 feet.
• When running wire, avoid locations concealing pipes, heating ducts and AC wiring in the
general vicinity.
• Avoid running wires close to house electrical wiring for any distance. If you have to run
them parallel, make sure to space the wires
at least two feet from the AC line.
27
Do not connect the controller's main power feed until all other connections have been
made and verified. Live connection or removal of the keypad wiring or other wiring
when the system is powered can cause communication problems in the network.
Double-check terminations during each phase of the installation to prevent accidental
damage. Incorrect wiring is the number one cause for non-warranty product damage.
CAUTION
Page 28
28
17
16
14
12
13
15
19 18
20
CAM6.6
ANTENNA
RNET LINK IN AND LINK OUT - Links multiple CAM6.6’s, also links future Russound
components that are RNET compatible
RS-232 INTERFACE - The RS-232 Interface allows the zones to be controlled by PC
or other devices that have an RS-232 Interface. The RS-232 Interface also allows for
firmware updates and programming.
AUX-MAIN RUN SWITCH - For firmware updates
UNO KEYPAD PORTS - One UNO Keypad Port for each of the six CAM6.6 Zones
12VDC TRIGGER OUT - 12VDC 100mA Trigger Out turns on when any zone is on
HOME THEATER 12VDC TRIGGER IN - 12VDC input jack notifies the CAM6.6 that
additional components are active, e.g., home theater equipment
MUTE 12VDC TRIGGER IN - Applying 12VDC to the Mute 12VDC Trigger In jack will
activate Audio for assigned CAM6.6 Zones and mutes the audio
MUTE 12VDC TRIGGER OUT - Mute Trigger Out supplies 12VDC 100 mA whenever
12VDC is applied to the Mute 12VDC Trigger In
IR LEARNING WINDOW - IR receiver for learning in IR commands with
confirmation LED
4
7
2
5
8
3
6
9
1
41 3 6 97 111052 8
INSTALLER
COMPONENT GUIDE
CAM6.6 Controller-Rear Panel
Page 29
29
INSTALLER
COMPONENT GUIDE
CAM6.6 Controller-Rear Panel
OPTIONAL INTERNAL SOURCE - Factory installed optional internal source, XM radio
module
AC 240V-AC 110V Switch - Switches A/C input voltage between 110VAC and
240VAC
AC 120/240 INPUT - Grounded 3-terminal plug detachable power cord connection
for the CAM6.6
FUSE HOLDER - Holds a replaceable fuse for A/C input connection
110VAC operation-F 3A H 250V, 240VAC operation-F 1.25A H 250V
SPEAKER OUTPUTS - Connect 8 Ohm speakers for each zone by using detachable
color-coded modular snap connectors
AUDIO OUTPUTS - Audio line output connection
FIXED/VARIABLE SWITCH - Change line out between fixed and variable output.
COMMON IR OUTPUT - Output jack will pass all IR signals from all keypads
SOURCE IR OUTPUTS - Six source-specific IR Output jacks allow for IR control of
source equipment
AUDIO INPUTS - Six sets of Audio Line Level input connections for CAM6.6 source
components
OUTPUT/INPUT SWITCH - Enable Source Input 1 or enables Internal Source 1 output
20
19
18
17
16
15
14
13
12
10
11
Page 30
30
INSTALLER
COMPONENT GUIDE
UNO-S1 Keypad-Update Port
OS Update/Run Jumper -The pins are jumpered when performing an OS update on the keypad, and removed during normal operation.
(Typically needed only on a keypad that has never been updated)
Setup Button - Activates information and update menus for the keypad.
OS Update Port - Used to update the UNO-S1 keypad operating system firmware. If an
update is released, it will be available online through the Document Center on
www
.russound.com.
Look for it in the “Firmware and Downloads” section under Multi-Zone
product type. The Advanced Programming Cable is available from Russound,
Part #2500-521065.
1
3
2
Data Rx TTL Level
Data Tx TTL Level
GND
+12VDC
Note: Do not put
RS-232-level signals
into the pins. Must use
Advanced
Programming Cable
P/N 2500-521065.
1
2
3
Page 31
31
INSTALLER
COMPONENT GUIDE
UNO-S1 Keypad-CAT-5 Connection
110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the
UNO-S1 Keypad and the CAM6.6 controller.
1
1
N
CAT-5 Connection
The UNO-S1 Keypad uses a 110-punchdown terminal to provide a simple installation and strong connection for CAT-5 cable’s eight conductors. Punchdown
terminals require the use of a punchdown tool which
has been provided with the keypad kit. Attach the
CAT-5 cable to the 110-punchdown terminal on the
UNO-S1 Keypad as shown, matching the conductor
colors to the connection color guide. The keypad will
not operate properly if the terminations deviate from
the required connection order.
Caution:
Take care when using an impact 110 punchdown tool, as
this may overspread the contact points. Use of the
impact tool may propel stray bits of wire and jacket into
the keypad’s chassis and possibly cause a short in the
circuitry. Gently shake or blow air through the keypad
chassis to remove stray wire before the keypad is
installed into the junction box.
EWMARKET
, NH U.S.A.
UNO-S1
System Control Keypad
BL
BL/WCOM B
OR/W
IR OUT
COM A
DESIGNED IN USA MADE IN KOREA
OR
GND
GR/W
GND
STATUS IN
BR/W+12V
+12V
BR
GR
Page 32
32
INSTALLER
COMPONENT GUIDE
UNO-S2 Keypad-Update Port
SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad
OS UPDATE PORT - The OS Update Port is used to update the UNO-S2 Keypad operating system software in the future. If an update is released, it will be available online
through the Document Center on
www
.russound.com.
Look for it in the “Firmware
and Downloads” section under Multi-Zone product type. The Programming Cable is
available from Russound, Part #2500-120633.
1
2
1
2
DATA Rx (RS-232)
DATA Tx (RS-232)
GND
N/C
+12VDC
Page 33
33
EXTERNAL IR RECEIVER IN CONNECTOR - Connection for an external IR Receiver.
OS UPDATE JUMPER - Selects “Run” or “OS Update” mode.
RESET BUTTON - Reset whenever changing from RUN to OS update
110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the
UNO-S2 Keypad and the CAM6.6 controller.
1
2
3
4
2
3
1
4
INSTALLER
COMPONENT GUIDE
UNO-S2 Keypad-CAT-5 Connection
KOREA
Page 34
34
INSTALLER
UNO-S1 KEYPAD-INSTALLATION
Keypad Location
The best infrared remote performance is achieved
with the keypad away from any direct sunlight,
plasma TV, and low voltage lighting controls. Also
consider convenience when choosing a location.
Choose a place that is easily seen from the position where a person is most likely to be located.
Check whether or not you can route the wire to
the location you have chosen.
Keypad Installation
To install a single-gang keypad, you will need to
use a UL/CSA approved plastic single-gang electrical box.
Route CAT-5 wire to the junction box from the
CAM6.6.
Use the supplied 110 punchdown tool to connect each wire to its corresponding color
labeled on the punchdown terminal.
Ensure jumper settings on keypads are in the
run positions.
Mount the keypad in the electrical box and
attach the cover plate. Repeat the steps until all
keypads are installed.
Junction Box UNO-S1 Back Plate Cover Plate
Blues
Page 35
35
INSTALLER
UNO-S2 KEYPAD-INSTALLATION
Keypad Location
Plastic Double-Gang
Electrical Box
UNO-S2
Back Plate
Screw
Screw
Screwless
Cover Plate
Keypad Installation
To install a double-gang keypad, you will need to
use a UL/CSA approved plastic double-gang
electrical box.
Route CAT-5 wire to the junction box from the
CAM6.6.
Use the supplied 110 punchdown tool to connect each wire to its corresponding color
labeled on the punchdown terminal.
Ensure jumper settings on keypads are in the
run positions.
Mount the keypad in the electrical box and
attach the cover plate. Repeat the steps until all
keypads are installed.
Page 36
36
The UNO System Keypad Ports are located on
the back of the CAM6.6 in the top left of center.
Connections made at the UNO Keypad Ports are
made using CAT-5 T568A RJ-45 wire configuration. CAT-5 is color-coded for ease of installation. For a clean installation when wiring from an
UNO System Keypad Port use an RJ-45 CAT-5
patch cable to connect from the keypad port to
an RJ-45 Wall Plate (optional). Using the same
CAT-5 T568A RJ-45 wiring configuration, use
CAT-5 from the RJ-45 Wall Plate to the keypad.
If using more than one keypad on a zone, connect a SA-ZX3 UNO System Keypad Splitter
(optional) directly to the UNO System Keypad
Port instead of going through the wall plate.
Always use the CAT-5 T568A RJ-45 wire configuration when wiring any of the UNO System
Keypad Ports.
INSTALLER
MAKING CONNECTIONS
UNO Keypad Port Connection
CAM6.6X
CAT-5 Cable
1201A/1A
Power
Supply
ANTENNA
SA-ZX3
CAM6.6
CAT-5 Cable
PM Mod 3D
with RJ-45
CAT-5 Cable
Page 37
37
Source Audio Connections
The CAM6.6 supports up to six audio sources.
The Source Inputs are located at the back panel.
The Source 1 input serves a dual purpose. If the
CAM6.6 optional internal source is used, the
Source 1 inputs are not available, and the switch
next to it is set to “Internal Source Output.” If the
Optional Internal Source is not installed, or if you
want to utilize the Source 1 inputs, set the switch
to “Input” and reconfigure Source 1 in the Source
Setup Menu. Connect each source output using
quality RCA signal cables. Connect the Left and
Right Audio outputs from each source to the corresponding inputs on the CAM6.6 controller. Label
each cable with the name of the selected source
and the Source Audio input number located on
the CAM6.6.
Source IR Connections
Each source component has a designated IR
port on the back of the CAM6.6. This IR port is
directly above the Source Audio Input
Connections.
1. Using an IR emitter (the Russound 845.1 is
recommended), attach the end of the emitter
with the 1/8
”
plug to the IR emitter port above
the source input.
2. Remove the adhesive back at the other end
of the emitter and attach the emitter over the
source component’s IR window.
3. In order to control this source component
with IR, the source must be selected at the
keypad receiving the command.
CAM6.6
ANTENNA
Tape Player
CD Changer
INSTALLER
MAKING CONNECTIONS
Source Audio and IR Input Connections
Use the source 1
output/input switch
for audio out of the
optional internal
source or audio in
of connected
source equipment.
CAM6.6 with Optional Internal Source - XM satellite radio
Page 38
38
INSTALLER
MAKING CONNECTIONS
Common IR Connection
Common IR Connections
The Common IR jack on the rear of the CAM6.6
allows control of any source equipment without
that source being selected on the keypad. The
connection for the COM IR jack is made using an
IR emitter with a 1/8’’ plug. The Russound
845.1 single IR emitter is recommended, or use
an IR connecting block such as the Russound
857 which allows multiple units to be controlled
through the COM IR Port.
ANTENNA
CAM6.6
Alternate configuration
using 857 IR connecting block
S
TATUS
+
12VDC
P
OWER
+
12VDC
IR R
ECEIVER IN
IR C
OMMON IN
+12VDC
GND
STATUS
SIGNAL
DESIGNED IN USA MADE IN KOREA
CONNECTING BLOCK
857 INFRARED
123456
IR CONFIRM
EMITTERS
IR emitters to
source equipment
Page 39
39
The speakers are connected to the CAM6.6
using modular snap connectors. Each of these
color-coded connectors is designated for the
speaker set of a particular amplified zone. To
avoid confusion, connect one zone speaker set
at a time starting with Zone 1, taking care to
keep zone and speaker wire identities straight.
Note: An 8 Ohm minimum speaker is required
for each amplified output.
1. Pull the speaker wire conductors apart so
they’re separated for the first two inches from
their ends.
2. Using a wire stripper, remove 1/4 inch of
insulation from each conductor. Twist the
strands in each conductor into tight spirals.
3. Remove the modular four-color connector for
Zone 1. The color code is as follows:
WHITE -- L+ (left channel positive)
GREEN -- L- (left channel negative)
BLACK -- R- (right channel negative)
RED -- R+ (right channel positive)
Lift the black lever for each connection until it
locks open and insert the proper speaker
wire, matching channel and polarity for all
four wires. Snap the lever down. Insert the
modular connector into its designated output
on the back of the CAM6.6.
4. Complete the same steps for the remaining
zones. Label each set of speaker wires with
the zone and location.
INSTALLER
MAKING CONNECTIONS
Speaker Connections
ANTENNA
CAM6.6
Page 40
40
The CAM6.6 has two Zone Audio outputs, on
Zone 1 and Zone 2. Each of these zone audio
output connections features a stereo line out
RCA connection plus a switch to allow for either
a fixed or a variable line level output. When set
to Variable, the keypad volume level affects this
output. In the Fixed position, keypad volume
level will not change the output level.
The fixed or variable audio outputs can be used
if additional amplification is desired (e.g.,
Russound DPA-1.2 two-channel amplifier). Use
quality RCA signal cables to ensure a constant
quality audio signal.
CAM6.6
ANTENNA
INSTALLER
MAKING CONNECTIONS
Zone Fixed/Variable Audio Outputs
Page 41
41
12VDC Home Theater Trigger In
This 12VDC Trigger input is used to control
Power Management of the audio sources possibly
being shared with a home theater system. When
the last zone on the CAM6.6 is turned off, 12VDC
presence to the trigger input will prevent the
sources that are on from being turned off. The
connections for the trigger are made using a twoconductor cable with 1/8” male mini-plug. The tip
is positive (+) and the sleeve is negative (-).
12VDC 100mA Trigger Out
The 12VDC 100mA trigger out can be used to
engage any 12VDC trigger device or component
such as the Russound ACT-1 triggered outlet.
The connections for the trigger out are made
using a two-conductor cable with 1/8” male
mini-plug jacks at each end. The tip is positive
(+) and sleeve is negative (-).
INSTALLER
MAKING CONNECTIONS
12VDC Home Theater Trigger In/Out
ANTENNA
CAM6.6
Page 42
42
12VDC Mute Trigger In
When 12VDC is applied to the Mute Trigger In,
the system will fully mute any source connected
to the Source Audio Input. The connections for
the trigger are made using a two-conductor cable
with 1/8” male mini-plug jacks. The tip is positive
(+) and sleeve is negative (-). This allows for the
connection of an external or muting device. The
CAM6.6 can be programmed to mute audio for
one or all zones as preferred when the 12VDC is
applied.
12VDC Mute Trigger Out
Mute Trigger Out 12VDC output is used for triggering an external amplifier, muting device or
other component dependent on the Mute Trigger
In 12VDC. The connections for the output are
made using a two-conductor cable with 1/8”
male mini-plug jacks at each end. The tip is positive (+) and sleeve is negative (-). The default
setting for the Mute Trigger Out provides 12VDC
whenever 12VDC is applied to the Mute Trigger
In.
INSTALLER
MAKING CONNECTIONS
12VDC Mute Trigger In/Out
Doorbell Interface
ANTENNA
CAM6.6
Page 43
43
The RNET Link In and Link Out is used to connect two or more CAM6.6 or CAV6.6 controllers. The connection is made using a CAT-5
patch cable from the Link Out of the master
CAM6.6 and into the Link In of the next controller. Along with RNET data signals, the RNET
Link In and Link Out jack passes the six source
IR signals. These are only for source-specific IR
remote repeating, not codes initiated from the
controller’s internal IR library. The CAT-5 patch
cable should not exceed 18 inches in length to
avoid potential cross-talk between the sourcespecific IR repeating signal lines.
The RNET Link In and Link Out is also used to
connect the CAM6.6 to other Russound products with RNET.
Note: If two or more CAM6.6 or CAV6.6 controllers will be connected using the RNET Link In
and Link Out ports, each controller must have a
unique Controller ID prior to being connected
through the RNET ports. The Controller ID
assignment must be performed during the
Controller Setup section of the Installation menu.
CAM6.6
ANTENNA
CAV6.6 (Controller ID 2)
CAM6.6 (Controller ID 1)
CAT-5 Cable (MAX LENGTH 18 inches)
INSTALLER
MAKING CONNECTIONS
RNET Link In and Link Out
Page 44
44
The CAM6.6 supports RS-232 communication
with various third party automation systems or
PC for programming of the controller. The RS232 com port is located on the back of the
CAM6.6 and uses a DB-9 cable connection. For
RS-232 protocol and the backup PC application,
see the Document Center at
www.russound.com.
Look for the Technical
Documents under Multi-source/Multi-room
products.
INSTALLER
MAKING CONNECTIONS
RS-232 Interface
DB-9 Cable
ANTENNA
INTERFACE
CAM6.6
Page 45
45
INSTALLER
MAKING CONNECTIONS
Optional Internal Source - XM Tuner Antennas
XM Antenna
Connect the included XM antenna for XM reception to the back panel of the XM module. The
antenna comes with 20 feet of cable. If this
length is not sufficient, there are aftermarket
antenna kits available for custom lengths.
Position the antenna near a south-facing window
to receive the best signal from a satellite or terrestrial signal.
The antenna may also be attached to an external wall by sliding the slots on the back of the
antenna onto four screws mounted on an exterior wall. Establish the best receiving position for
the antenna before attaching it to the wall.
XM Signal Strength Mode
To test the XM reception, turn the unit on. When
the XM radio is powered for the first time, the
XM service will start playing XM Channel 1, a
preview/promotional channel. Verify that Channel
1 is playing by viewing the channel number on
the keypad display. Enter Signal Strength Mode
by pressing and holding the Stop button on the
UNO-S2 keypad. The display shows one of the
following:
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL Loss of signal
Adjust the antenna until GOOD SIGNAL is displayed. Press Stop to exit Signal Strength Mode.
CAM6.6
Page 46
46
Before proceeding to the system programming section, it’s important to conduct an initial test to
determine that the hardware components are working properly.
1. Connect the speaker wires from Zone #3 to the CAM6.6 Zone #3 speaker output connectors.
2. Connect an UNO-S1 or UNO-S2 keypad to Keypad Port #3 on the rear of the CAM6.6.
3. Connect a source to the Source #3 Input on the CAM6.6 using RCA Audio patch cables.
4. Plug a supplied 845.1 IR emitter into the Source #3 IR Output Jack and adhere the emitter end
to the source equipment’s IR window.
5. Plug in the main power cords for the CAM6.6 and the source.
6. Turn on the main power switch on the CAM6.6 and the source.
7. Manually command the source to provide audio or use the source remote control.
8. Press the power button on the UNO-S1 or UNO-S2 keypad and select Source #3.
Congratulations – you should now hear the source through the speakers in Zone #3.
If there is no sound, follow these diagnostic steps:
1. Check the source to see that it is operating properly.
2. Check the RCA Audio cable connections from the source to the Source #3 Input on the
CAM6.6.
3. Check the speaker connections and verify that they are correct and are connected to the
Zone #3 speaker outputs.
4. Check to see that the keypad is connected to the Zone #3 Keypad Port and verify the CAT-5 is
properly terminated at both ends.
If none of these steps produce successful results, call Russound Tech Support for further assistance.
INSTALLER
INITIAL INSTALL TEST
Page 47
This manual includes items that are designed to assist in the programming process.
Forms (Pages 49-51)
Three blank reproducible forms are included as planning tools when determining sources, settings
and zone preferences. The Source and Zone Information forms and the Macro Editor form should be
completed before programming, and referred to during the Installation Menu process. This speeds up
programming time and reduces missed or incorrect entries. These forms also serve as system reference documents if future troubleshooting is needed.
IR Device Codes (Pages 80-82)
This list of command type IR device codes reflects the built-in IR codes in the CAM6.6 library. During
programming, these codes will be entered for each source at the “Device Code” prompt. If a code is
not listed for a source, the Learn IR procedure is available to learn in and centrally store IR codes.
(Note: Device codes for Phono, DAT and Tape are Learned Only)
Key Functions (Pages 83-104)
This list of key functions identifies what IR codes are supported for each command type (source) by
the built-in library. “Learned Only” indicates that this function is not supported and must be learned
into the CAM6.6. This list of key functions reflects the different available key functions associated
with what you see on the LCD panel when performing the Key Configuration procedure in the
Installation Menu. The list of functions corresponds with the command types above (e.g., Tuner, CD
player, etc.).
Source Names (Pages 105-106)
A list of assignable Source Names is provided for advance selection and source form completion
before programming.
Flow Charts (Pages 67-79)
Installation Menu flow charts provide a graphical representation of the programming process.
Installation Menu (Pages 52-66)
The Installation Menu provides the step-by-step complete programming procedure for the keypad and
the controller.
Although you can begin programming at any point within the Installation Menu, the following sequence
is recommended for initial installations, as it progresses from the most basic requirements to the
more advanced features.
1. Controller Setup (CTRLR SETUP) (Page 62)
This procedure sets the controller ID number within the system. This number must be manually set
when multiple CAM6.6’s are linked through RNET within one system. This procedure is not necessary
for systems with only one CAM6.6.
2. Number of Sources (# of Sources/SOURCE SETUP) (Page 61)
This procedure sets the number of sources used in the system. This prevents the user from selecting
a source input that is not used.
INSTALLER
SYSTEM PROGRAMMING OVERVIEW
47
Page 48
48
3. Basic Setup (SOURCE SETUP) (Pages 55-56)
This procedure is mandatory to set up each source for keypad source control and is the cornerstone
of the programming process.
4. Peripheral Setup (Pages 53-55) (FOR OPTIONAL INTERNAL SOURCE)
This procedure provides setup and naming procedures for the XM tuner. It includes assigning a custom name to a memory preset or bank.
5. Learn IR (Page 64-65)
This procedure is used when the source-specific IR code is not found in the built-in IR code library.
This allows IR commands to be learned into the system and centrally stored.
6. Macro Editor (Page 65-66)
This procedure compiles multiple IR keycodes to be initiated by a single button press. One macro can
have up to 10 commands, including other macros, and up to 132 macros can be entered.
7. Source Volume Trim (SOURCE SETUP) (Page 58)
This procedure matches audio output signals for all sources for seamless switching.
8. Numeric IR (SOURCE SETUP) (Pages 58-60)
This procedure sets up control of a source that supports direct numeric commands.
9. Key Configuration (SOURCE SETUP) (Pages 57-58)
This procedure customizes individual key functions on a per-zone basis for source control.
10. Power Management (Pages 62-64)
This function incorporates IR macro commands to automatically control the power state of the sources
when the system is in use or when a home theater is sharing sources.
11. Zone Volume Trim (ZONE SETUP) (Page 61)
This procedure limits the maximum volume allowed in a zone, regardless of keypad volume adjustment.
12. System On Enable (SYSON ENABLE/ZONE SETUP) (Page 61)
This feature allows a zone to join or opt out of an “all on” command.
13. Party Enable (ZONE SETUP) (Page 62)
This feature allows a zone to join or opt out of Party Mode participation.
14. Master Enable (ZONE SETUP) (Page 62)
This feature allows a zone the option of becoming a Master keypad in Party Mode.
15. Mute Enable (ZONE SETUP) (Page 62)
This feature enables a zone to allow or to mute audio.
INSTALLER
SYSTEM PROGRAMMING OVERVIEW
Page 49
49
INSTALLER
SETUP FORMS
<XM>
N/A
Russound
N/A
N
N/A
N/A
N
N/A
Peripheral
Page 50
50
INSTALLER
SETUP FORMS
Mute
Page 51
51
INSTALLER
SETUP FORMS
Page 52
52
INSTALLER
INSTALLATION MENU OVERVIEW
There are three item types in the installation menu:
Menu Item (m) – Acts as a folder that holds procedures and/or feature parameters.
Procedure (p) – A sequence of feature parameters to perform a guided operation, such as
configuring an UNO key. Once you begin a procedure, the system will prompt for
the needed information to complete the task.
Feature (f) – The actual parameters (settings) that will change the system configuration.
The following keys on the UNO-S2 keypad are used to navigate and make changes while using the
installation menus:
To enter the Installation Menu, press and release the Setup Button (located on the keypad’s right
side) while in normal operating mode. The Setup Button is used to “back out” of the Installation Menu
one level at a time. If you are performing a procedure, the Setup Button brings you back to the
beginning of the procedure. Once you have reached the top level of the Installation Menu, pressing
the Setup Button brings you back to normal operating mode.
Adjust feature setting (increment).
Adjust feature setting (decrement).
Go to next menu / procedure / feature.
Not available while performing a procedure.
Go to previous menu / procedure / feature.
Not available while performing a procedure.
Enter menu / begin procedure / show current feature setting.
While performing a procedure, it is
also used to advance to the next sequential feature setting once the current feature has been viewed
or adjusted.
UNO-S1 Keypad Five-Character Display
The UNO-S1 keypad abbreviates information as necessary to appear in its five-character display. In
the following menu procedures, the UNO-S1 five-character abbreviation is shown in parentheses
underneath the 12-character version.
Page 53
53
The following items make up the Installation Menu:
PERIPH SETUP (PerSu) SOURCE SETUP (SrcSu) ZONE SETUP (ZonSu)
CTRLR SETUP (CtlSu) POWER MGT (PwMgt) LEARN IR (LrnIR)
MACRO EDITOR (MacEd) SYSTEM INFO (SInfo)
PERIPH SETUP (PerSu)
Peripheral Setup allows the CAM6.6’s optional internal source to be configured.
The following items can be found in the PERIPH SETUP menu:
MEM NAME (MemNm) BANK NAME (BnkNm) CONTROLLR ID (CtlId) DIAGNOSTICS (Diags) FACTORY INIT (FInit) SYSTEM INFO (SInfo)
MEM NAME (MemNm)
NOTE: A memory preset must be created and saved before it can be named. Once it is saved, the
preset’s Tuner #, Bank # and Memory # must be entered in the following procedure.
This procedure accesses a name entry field to enter a custom name for a memory preset.
See
Periph Setup - Flow Chart page 67
1. BANK # – Select the BANK # of the memory preset.
(Bank#)
2. MEMORY # – Select the MEMORY # of the preset to be named.
(Mem #)
3. MEMORY NAME – Use the up/down keys to select a character and left/right keys
(MemNm) to change a character position. A blinking cursor indicates the
placement of the character being entered. Names can be from 1
to 12 characters in length.
BANK NAME (BnkNm)
This procedure accesses a name entry field to enter a custom name for each of the tuner’s six
banks.
See Periph Setup - Flow Chart page 67
1. BANK # – Select the BANK # of the memory preset.
(Bank#)
INSTALLER
INSTALLATION MENU
Page 54
INSTALLER
INSTALLATION MENU
2. BANK NAME – Use the up/down keys to select a character and left/right keys
(BnkNm) to change a character position. A blinking cursor indicates the
placement of the character being entered. Names can be from 1
to 12 characters in length.
CONTROLLR ID (CtlId)
This procedure is used to identify the controller(s) that the tuner will respond to.
See Periph Setup
- Flow Chart page 68
1. Controller:# – Select controller ID of controller that will control tuner.
(CtlId)
2. All controllers – Select if all controllers in system can control the tuner.
(All)
DIAGNOSTICS (Diags)
This procedure is for factory use only.
See Periph Setup - Flow Chart page 68
F
ACTORY INIT (FInit)
NOTE: This procedure returns the tuner to its factory settings and erases all user settings.
This procedure allows the erasure of all programmed settings and returns them to the factory default
settings.
See Periph Setup - Flow Chart 68
1. Are you sure? – Confirmation of YES or NO is required to proceed. A NO
(Sure?) selection returns to the top of the Factory Initialization menu.
A YES selection begins the initialization.
2. Please Wait – Message shows during the initialization process.
3. Cycle Power – When initialization is complete, cycle power to the unit.
SYSTEM INFO (SInfo)
System Info shows the tuner’s manufacturing build properties.
See Periph Setup - Flow Chart 68
BUILD TIME (BTime) BUILD DATE (BDate) VERSION (Ver)
54
Page 55
55
1. BUILD TIME Displays the firmware Build Time of the tuner.
(BTime)
2. BUILD DATE Displays the firmware Build Date of the tuner.
(BDate)
3. VERSION Displays the firmware version of the tuner.
(Ver)
SOURCE SETUP (SrcSu)
Source Setup allows the system’s sources to be configured.
The following items can be found in the SOURCE SETUP menu:
BASIC SETUP (BasSu) KEY CONFIG (KeyCf) SOURCE NAMES (SrcNm)
SRC VOL TRIM (SrcVT) NUMERIC IR (NumIR) SRC SEL CMD (SrcSC)
# OF SOURCES (#Srcs)
BASIC SETUP (BasSu)
NOTE: The BASIC SETUP procedure should be performed for each source before proceeding to other
source setting changes.
NOTE: If the CAM6.6 has an optional internal source installed, it is pre-configured as Source 1, with
source name <XM> and command type Peripheral.
This procedure uses built-in source “templates” to quickly and easily configure the source settings
needed for basic operation of the source component. Before performing BASIC SETUP, connect the
source components to the CAM6.6 as outlined in the Source Connections section. Also be sure that
all sources are powered on.
See Basic Setup - Flow Chart 69
1. SOURCE NUM – Select the source to be configured.
(Src #)
2. SOURCE NAME – Select the name for the source (e.g., DVD, Aux 2, Jazz, etc.).
(Name)
3. COMMAND TYPE – Select the type of command template (e.g., CD, TV, etc.). Selecting
(CmdTp) the command type template will tell the CAM6.6 how to configure the
key’s command and text for the source component.
INSTALLER
INSTALLATION MENU
Page 56
56
INSTALLER
INSTALLATION MENU
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. (See Learning IR procedure for instructions on how
to learn IR codes.)
ii. TEMPLATE TYP – Select the template type to define what type of source compo-
(TType) nent is being used. (This will tell the CAM6.6 how to configure
the key commands and text for the source component if it is a
learned source.) Procedure advances to USE NUM IR? (step 7).
b. Selected: Unassigned The template for the selected source is cleared. (All key
(Unasg) assignments and other source settings will be erased.)
Procedure advances to SAVE CHANGES (step 10)
c. All Other Selections: Procedure advances to DEVICE CODE (step 4)
4. DEVICE CODE – Enter source component code number listed in this manual’s
(DevCd) Reference section.
5. TEST IR? – If “Yes” is selected, the CAM6.6 sends a power command to the
(TstIR) source component. If “No” is selected, the procedure advances
to USE NUM IR? (step 7)
6. SUCCESS? – If the power to the source component was turned off, select
(OK?) “Yes” otherwise select “No.” By selecting “No” the Procedure
returns to DEVICE CODE (step 4) to allow selection of another
code number from the provided list.
7. USE NUM IR? – Indicates the source component has numeric scrolling, such as
(NumIR) multi-disc CD player (See NUMERIC IR Setup Procedure for
advanced settings or more information). “No” advances menu to
AUTO PLAY (step 9).
8. HIGHEST NUM – Enter the highest possible number; for example, a 100-disc CD
(High#) player would have a max number of 100.
9. AUTO PLAY? – “Yes” tells the CAM6.6 to issue a PLAY command whenever the
(AtoPl) source is selected for listening. This option is skipped if the
source type (COMMAND TYPE) chosen does not have a PLAY
command associated with it.
10. SAVE CHANGES? – Select “yes” to save changes. Procedure returns to SOURCE
(Save?) NUM to allow configuration of another source.
Page 57
57
KEY CONFIG (KeyCf)
Key Configuration defines zone-specific key functions for each source.
See Key Config. - Flow Chart
page 70
1. ZONE NUM – Select the zone the key will be configured for. Changes are made
(Zone#) for that zone only; default setting is “All Zones.”
2. SOURCE NUM – Select the source the key will be configured for.
(Src #)
3. SELECT A KEY – Using or , select the keypad key to be configured.
(SelKy)
4. KEY TYPE – Either “Key Press,” “Key Hold” or “Both” will activate the command.
(KeyTp)
5. KEY NAME – Name that appears on the keypad display when the command is
(KeyNm) activated.
6. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR – Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 8)
b. Selected: Unassigned The key configuration is cleared. Procedure advances to SAVE
(Unasg) CHANGES (step 9)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 8)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO - Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SAVE CHANGES
(MacID) (step 9)
e. All Other Selections: Procedure advances to DEVICE CODE (step 7)
7. DEVICE CODE – Enter source component code number listed in this manual’s
(DevCd) Reference section.
8. KEY FUNCTION – Select a function for the button.
(KeyFn)
INSTALLER
INSTALLATION MENU
Page 58
58
INSTALLER
INSTALLATION MENU
9. SAVE CHANGES? – Select “yes” to save changes. Procedure advances to ZONE NUM
(Save?) (step 1)
SOURCE NAMES (SrcNm)
This procedure allows the installer to customize the source names for the sources attached to the
CAM6.6.
See Source Names/Vol Trim - Flow Chart page 71
1. SOURCE NUM – Select the source number this name will be assigned to.
(Src #)
2. SOURCE NAME – Select the name. SOURCE NUM will reappear on the LCD panel;
(Name) repeat the instructions for each source to be labeled.
SRC VOL TRIM (Sr
cVT)
This procedure allows the installer to adjust the output level of an individual source. The output volume is adjustable by 16dB. At 0dB (-3dB default setting), the volume is at max output; at -16dB the
volume is at the lowest setting possible for that source only.
See Source Names/Vol Trim - Flow
Chart page 71
1. SOURCE NUM – Select the source number this level will be set for.
(Src #)
2. TRIM LEVEL – 0 dB is max output volume, -16 dB is lowest setting.
(Trim)
NUMERIC IR (NumIR)
Numeric IR allows the installer to program source specific number functions (Channel 12, Disk 89, etc.).
See Numeric IR - Flow Chart page 72
1. SOURCE NUM – Select the source number this function will be configured for.
(Src #)
2. USE NUM IR? – Tells the system whether the source component has numeric
(NumIR) scrolling, such as 100-disc CD player. A selection of “no” dis-
ables Numeric IR and advances to SAVE CHANGES
3. HIGHEST NUM – Enter the highest possible number; for example, the 100-disc CD
(High#) player would have a max number of 100.
Page 59
59
4. NUMERIC TEXT – Select Numeric descriptive text.
(NmTxt)
5. PREFIX CMD – Tells the system whether a command will be issued prior to the
(Prefx) selection of the numerical value (e.g.,
Disc
1,2). If “no,”
procedure advances to SUFFIX CMD (step 9)
6. COMMAND TYPE – Select the type of command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 8)
b. Selected: Unassigned The numeric IR Prefix command is cleared. Procedure advances
(Unasg) to SUFFIX CMD (step 9)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 8)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO - Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SUFFIX CMD (step 9)
(MacID)
e. All Other Selections: Procedure advances to DEVICE CODE (step 7)
7. DEVICE CODE – Source component code for IR control.
(DevCd)
8. KEY FUNCTION – Select a function (Disc, etc.).
(KeyFn)
9. SUFFIX CMD – Tells the system whether a command will be issued after the
(Sufix) selection of the numerical value (e.g., 1, 2
Enter
). If “no,” proce-
dure advances to SAVE CHANGES (step 13)
10. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
INSTALLER
INSTALLATION MENU
Page 60
INSTALLER
INSTALLATION MENU
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 12)
b. Selected: Unassigned The numeric IR Suffix command is cleared. Procedure advances
(Unasg) to SOURCE NUM (step 1)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 12)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO - Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SAVE CHANGES
(MacID) (step 13)
e. All Other Selections: Procedure advances to DEVICE CODE (step 11)
11. DEVICE CODE – Source component code for IR control.
(DevCd)
12. KEY FUNCTION – Select a function (Enter, Play, etc.).
(KeyFn)
13. SAVE CHANGES? – Select “yes” to save the changes.
(Save?)
SRC SEL CMD (SrcSC)
This procedure permits a command to be sent to the source component when the source component
is initially selected.
See Source Select Command & # Of Sources - Flow Chart page 73
1. SOURCE NUM – Select the source number this command will be configured for.
(Src #)
2. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 4)
b. Selected: Unassigned The source select command is cleared. Procedure advances to
(Unasg) SAVE CHANGES (step 5)
60
Page 61
61
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 4)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO - Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to SAVE CHANGES
(MacID) (step 5)
e. All Other Selections: Procedure advances to DEVICE CODE (step 3)
3. DEVICE CODE – Source component code for IR control.
(DevCd)
4. KEY FUNCTION – Select a function (Play, Enter, etc.).
(KeyFn)
5. SAVE CHANGES? – Select “yes” to save the changes.
(Save?)
# OF SOURCES (#Sr
cs)
At this field it is necessary to enter the number of sources used in the CAM6.6 system (1 to 6). This
limits the sources displayed on the keypad in the normal running mode when the source button is
pressed, but also limits source selections in the configuration menus.
See Source Select
Command & # Of Sources - Flow Chart page 73
ZONE SETUP (ZonSu)
NOTE: This procedure should be performed using the keypad installed in the zone to be configured.
See Zone Setup - Flow Chart page 74
Zone Setup allows the installer to adjust properties of the UNO Keypad controlled CAM6.6 zone. This
series of menus allows the system’s zones to be configured for these properties:
ZON VOL TRIM (ZonVT) SYSON ENABLE (SysOn) PARTY ENABLE (PtyEn)
MASTER ENABL (MstEn) MUTE ENABLE (MutEn)
1. ZON VOL TRIM - This feature allows the installer to adjust the output volume to
(ZonVT) each zone. -16 dB (lowest) to 0 dB (max)(-3dB default).
2. SYSON ENABLE - This feature is either disabled or enabled. If disabled (default), an
(SysOn) All On command activated from another zone will not turn on the
INSTALLER
INSTALLATION MENU
Page 62
62
INSTALLER
INSTALLATION MENU
disabled zone. If enabled, an All On command activated from
another zone will turn on the enabled zone.
3. PARTY ENABLE - This feature is either disabled or enabled. If disabled, Party Mode
(PtyEn) activation from another zone will not affect the disabled zone. If
enabled (default), the zone will participate with Party Mode.
4. MASTER ENABLE - This feature is either disabled or enabled. If disabled, the zone
(MstEn) cannot host a master keypad during Party Mode. If enabled
(default), the zone has the option of hosting the Master keypad.
5. MUTE ENABLE - This feature is either disabled or enabled. It allows the option of
(MutEn) enabling or disabling muting in a zone. If disabled, the zone will
not mute. If enabled (default), the zone will be muted when a
mute signal is received.
CTRLR SETUP (CtlId)
Controller Setup is the basic configuration of the controller. This setup menu selects the options for
Controller ID and Factory Initialization.
See Controller Setup - Flow Chart page 75
1. CONTROLLER ID - This defines the Controller ID for this system. The default is 1 but
(CtlId) when multiple controllers are used, each additional controller ID
must be sequential and unique and be set before being connected to the system. Note that the system must be restarted before
the controller will assume the new ID.
2. FACTORY INIT -
WARNING: This procedure returns the controller to its
(FInit)
original settings - use with discretion.
Factory Initialization allows the installer to erase all programmed
settings and returns the settings to the factory default settings.
All settings including source equipment IR commands will need to
be reentered. An “Are you sure?” prompt and a “no” response
allows the installer to cancel the reset; a “yes” at the prompt will
load factory/default settings.
POWER MANAGEMENT (PwMgt)
The CAM6.6 is capable of managing the power state of the connected source equipment. The power
management is configured on a source-by-source basis.
Page 63
63
All sources that have power management enabled are initialized by a “POWER ON” command/ macro.
Power management is initialized when the first keypad is turned on or when the home theater trigger
input has 12VDC present. The 12VDC trigger output is turned on when the first zone is turned on.
All sources that have power management enabled are turned off by the “POWER OFF” command after
all zones have been turned off, with a timeout of five minutes.The 12VDC trigger output is turned off
one minute after that. This timeout is postponed for as long as the home theater trigger input has
12VDC present.
See Power Management - Flow Chart page 76
1. SOURCE NUM – Select the source number this feature will be configured for.
(Src #)
2. POWER ON CMD – Tells the controller to turn on the selected source equipment (by
(OnCmd) SOURCE NUMBER) when any of the UNO System Keypads is
turned on. If “no,” procedure advances to POWER OFF CMD (step 6)
3. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 5)
b. Selected: Unassigned The Power On command is cleared. Procedure advances to
(Unasg) POWER OFF CMD (step 6)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 5)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO - Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number. Menu advances to POWER OFF CMD
(MacID) (step 6)
e. All Other Selections: Procedure advances to DEVICE CODE (step 4)
4. DEVICE CODE – Source component code for IR control.
(DevCd)
5. KEY FUNCTION -- Select a function (Play, Enter, etc.).
(KeyFn)
INSTALLER
INSTALLATION MENU
Page 64
INSTALLER
INSTALLATION MENU
6. POWER OFF CMD – Tells the controller to turn off the selected source equipment (by
(OfCmd) SOURCE NUMBER) when the last of the UNO System Keypads is
turned off. If “no,” procedure advances to SAVE CHANGES (step 10)
7. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 9)
b. Selected: Unassigned The Power Off command is cleared. Procedure advances to
(Unasg) SAVE CHANGES (step 10)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 9)
d. Selected: Macro: (To build macros, see Macro Editor page 65)
i. MACRO – Macro loads a series of commands which are processed when
(Macro) activated.
ii. MACRO ID – Enter the macro ID number.Menu advances to SAVE CHANGES
(MacID) (step 10)
e. All Other Selections: Procedure advances to DEVICE CODE (step 8)
8. DEVICE CODE – Source component code for IR control.
(DevCd)
9. KEY FUNCTION – Select Keypad function.
(KeyFn)
10. SAVE CHANGES? – Select “yes” to save the changes.
(Save?)
LEARN IR (LrnIR)
This procedure allows IR commands to be learned into the system and be centrally stored in the main
controller to let the system access the same IR codes that operate the source equipment.
NOTE: IR codes must be learned in by pointing the remote at the CAM6.6’s REAR panel IR receiver
only.
See Learn IR - Flow Chart page 77
1. LEARNED SRC – Select the source (Source 1-6 and Miscellaneous Learned IR
(LnSrc) (Misc)) whose commands will be learned into the controller.
64
Page 65
65
2. KEY FUNCTION – Select the function to be learned or deleted.
(KeyFn)
3. LEARN/DELETE – Select Learn IR Now or Delete IR. If Learn IR Now, a “USE
(Ln/Dl) REMOTE” prompt appears. Point the learning remote at the
controller’s IR window. If Delete IR, procedure returns to
LEARNED SRC (step 1)
4. TEST IR? – If “yes,” sends the learned command to the source component
(TstIR) to test the IR. If the component responds, the IR test was a
success. If the component does not respond the Code was not
learned properly. If “no,” menu goes back to LEARNED SRC
(step 1)
5. SUCCESS? - Asks if the IR test was a success
(OK?)
IF YES - If the test was a success, specify “yes” and proceed to
KEY FUNCTION (step 2)
IF NO - If the test was a failure, specify “no” and LEARN/DELETE
(step 3) reappears on the display allowing another code to be
learned in.
MACRO EDITOR (MacEd)
This procedure is used to create a sequence of commands that are launched with one key touch or
other event. Up to 132 macros can be created for the system, and each macro can contain up to 10
commands including other macros and delays.
See Macro Editor - Flow Chart page 78
1. MACRO ID – Number of Macro up to 132 including any previously named
(MacID) macros.
2. MACRO NAME – Name of Macro (optional).
(MacNm)
3. COMMAND NUM – Number of Command up to 10.
(Cmd#)
4. COMMAND TYPE – Select the type of source command (e.g., CD, TV, etc.).
(CmdTp)
a. Selected: Learned IR Choose Learned IR if the pre-programmed IR code library does
(LrnIR) not support the source component.
i. LEARNED SRC – Select the learned source bank to be assigned to the source
(LnSrc) component. Procedure advances to KEY FUNCTION (step 6)
INSTALLER
INSTALLATION MENU
Page 66
66
b. Selected: Unassigned Selected command and subsequent commands are cleared.
(Unasg) Procedure advances to COMMAND NUM (step 3)
c. Selected: Default Default selects the same device type and device code previously
(Deflt) setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 6)
d. Selected: Macro:
i. MACRO - A macro can “call” another macro if a sequence of more than 10
(Macro) commands is needed.
ii. MACRO ID – Enter the macro ID number. Menu advances to COMMAND NUM
(MacID) (step 3)
e.Selected: Delay Enter a 1- to 60-second delay time to postpone delivery of the
(Delay) next command in the macro. Procedure advances to COMMAND
NUM (step 3)
f. All Other Selections: Procedure advances to DEVICE CODE (step 5)
5. DEVICE CODE – Source component code for IR control.
(DevCd)
6. KEY FUNCTION – Select a function (Play, etc.).
(KeyFn)
SYSTEM INFO (SInfo)
System Info allows the installer to view the controller’s manufacturing build properties.
See System Info - Flow Chart page 79
#CONTROLLERS (#Ctls) BUILD TIME (BTime) BUILD DATE (BDate) VERSION (Ver)
1. #CONTROLLERS Displays the number of CAM6.6 controllers in the system.
(#Ctls)
2. BUILD TIME Displays the Software Build Time of the controller.
(BTime)
3. BUILD DATE Displays the Software Build Date of the controller.
(BDate)
4. VERSION Displays the software version of the CAM6.6.
(Ver)
INSTALLER
INSTALLATION MENU
Page 67
67
INSTALLER
SETUP MENU FLOW CHARTS
Menu
Peripheral
INFO
SYSTEM
Procedure
INIT
Procedure
FACTORY
Peripheral Setup: Memory Name, Bank Name
SETUP
PERIPH
Menu
Procedure
DIAGNOSTICS
ID
Procedure
CONTROLLR
BANK
NAME
Procedure
MEM
NAME
Procedure
NAME
MEMORY
MEMORY #
BANK #
SAVE
CHANGES?
BANK
NAME
BANK #
Selects
character
Selects
character
Selects
character
position
Selects
character
Repeat
position
for each
character
in name
Repeat
for each
in name
character
SAVE
CHANGES?
Page 68
68
INSTALLER
SETUP MENU FLOW CHARTS
Menu
Peripheral
INFO
SYSTEM
Procedure
Factory Init, System Info
Peripheral Setup: Controller ID, Diagnostics,
SETUP
PERIPH
Menu
INIT
Procedure
FACTORY
Procedure
DIAGNOSTICS
ID
Procedure
CONTROLLR
BANK
NAME
Procedure
MEM
NAME
Procedure
This
Procedure
This
Procedure
to its
Tuner
Factory
returns the
is for
ONLY
Factory use
Controller:#
All Contrlrs
settings
Are you sure
NO
YES
Please wait
Cycle Power
Page 69
69
INSTALLER
SETUP MENU FLOW CHARTS
Peripheral
Menu
SETUP
PERIPH
Page 70
70
INSTALLER
SETUP MENU FLOW CHARTS
Menu
SETUP
PERIPH
Page 71
71
INSTALLER
SETUP MENU FLOW CHARTS
Menu
SETUP
PERIPH
Page 72
72
INSTALLER
SETUP MENU FLOW CHARTS
Menu
SETUP
PERIPH
Page 73
73
INSTALLER
SETUP MENU FLOW CHARTS
Menu
SETUP
PERIPH
Page 74
74
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
MUTE
Menu
Page 75
75
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
Menu
Page 76
76
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
Menu
Page 77
77
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
Menu
LED on rear
blinks fast
CAM Panel
Page 78
78
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
Menu
Page 79
79
INSTALLER
SETUP MENU FLOW CHARTS
SETUP
PERIPH
Menu
Page 80
80
INSTALLER
IR CODES
Device Codes for TVs:
AOC 0030, 0019
Admiral 0093, 0463
Advent 0761
Aiko 0092
Aiwa 0701
Akai 0030
Alaron 0179
America Action 0180
Ampro 0751
Anam 0180
Apex Digital 0748, 0765, 0767
Audiovox 0451, 0180, 0092, 0623
Baysonic 0180
Belcor 0019
Bell & Howell 0154, 0016
Bradford 0180
Brockwood 0019
Broksonic 0236, 0463
CXC 0180
Candle 0030, 0056
Carnivale 0030
Carver 0054
Celebrity 0000
Changhong 0765
Cineral 0451, 0092
Citizen 0060, 0030, 0056, 0092
Concerto 0056
Contec 0180
Craig 0180
Crosley 0054
Crown 0180
Curtis Mathes 0047, 0747, 1147, 1347, 0054,
0154, 0051, 0451, 0093, 0060,
0030, 0056,
0145, 0166, 0016, 0702, 0466
Daewoo 0451, 0019, 0092, 0623
Daytron 0019
Denon 0145
Dumont 0017, 0019
Dwin 0720, 0774
Electroband 0000
Emerson 0154, 0236, 0463, 0180, 0178,
0179, 0019, 0623
Envision 0030
Fisher 0154
Fujitsu 0179, 0683
Funai 0180, 0179, 0171
Futuretech 0180
GE 0047, 0747, 1147, 1347, 0051,
0451, 0093, 0178, 0021
Gibralter 0017, 0030, 0019
GoldStar 0030, 0178, 0056, 0019
Gradiente 0053, 0056
Grunpy 0180, 0179
Hallmark 0178
Harley Davidson 0179
Harman/Kardon 0054
Harvard 0180
Havermy 0093
Hitachi 0056, 0145, 0016
Infinity 0054
Inteq 0017
JBL 0054
JCB 0000
JVC 0053
KEC 0180
KTV 0180, 0030
Kenwood 0030, 0019
Konka 0628, 0632, 0638, 0703, 0707
LG 0056
LXI 0047, 0747, 0054, 0154, 0156,
0178
Logik 0016
Luxman 0056
MGA 0150, 0030, 0178, 0019
MTC 0060, 0030, 0056, 0019
Magnavox 0054, 1254, 0030, 0179, 1454
Majestic 0016
Marantz 0054, 0030
Matsushita 0250
Megatron 0178, 0145
Memorex 0154, 0250, 0463, 0150, 0178,
0179, 0056, 0016
Midland 0047, 0747, 0017, 0051
Minutz 0021
Mitsubishi 0093, 0150, 0178, 0019
Motorola 0093
Multitech 0180
NAD 0156, 0178, 0166
NEC 0030, 0056, 0019
NTC 0092
Nikko 0030, 0178, 0092
Onwa 0180
Optimus 0154, 0250, 0166
Optonica 0093
Orion 0236, 0463, 0179
Panasonic 0051, 0250
Penney 0047, 0747, 1347, 0156, 0051,
0060, 0030, 0178, 0021, 0056,
0019
Philco 0054, 0463, 0030, 0145, 0019
Philips 0054, 1454
Pilot 0030, 0019
Pioneer 0166, 0679
Portland 0019, 0092
Princeton 0717
Prism 0051
Proscan 0047, 0747
Proton 0178, 0466
Pulsar 0017, 0019
Quasar 0051, 0250
RCA 0047, 0747, 1047, 1147, 1247,
1347, 1447, 0090, 0051, 0093,
0019, 0679
Radio Shack 0047, 0747, 0154, 0180, 0030,
0178, 0056, 0019
Realistic 0154, 0180, 0030, 0178, 0056,
0019
Runco 0017, 0030, 0603
SSS 0180, 0019
Sampo 0030
Samsung 0060, 0030, 0178, 0056, 0019,
0702, 0766
Sansei 0451
Sansui 0463
Sanyo 0154
Scimitsu 0019
Scotch 0178
Scott 0236, 0180, 0178, 0179, 0019
Sears 0047, 0747, 0054, 0154, 0156,
0178, 0179, 0056, 0171
Semivox 0180
Semp 0156
Sharp 0093, 0688, 0689
Shogun 0019
Signature 0016
Sony 0000, 1100
Soundesign 0180, 0178, 0179
Squareview 0171
Starlite 0180
Supreme 0000
Sylvania 0054, 0030, 0171
Symphonic 0171, 0180
TMK 0178, 0056
TNCi 0017
Tandy 0093
Technics 0051, 0250
Technol Ace 0179
Techwood 0051, 0056
Teknika 0054, 0180, 0150, 0060, 0179,
0056, 0019, 0092, 0016
Telefunken 0056, 0702
Toshiba 0154, 0156, 0060, 1256
Vector Research 0030
Victor 0053
Vidikron 0054
Vidtech 0178, 0019
Wards 0054, 0030, 0178, 0021, 0179,
0056, 0019, 0016
Waycon 0156
White Westinghouse 0463, 0623
Yamaha 0030, 0019, 0769
Zenith 0017, 0463, 0092, 0016
Device Codes for Cable:
ABC 0003, 0008, 0014, 0017
Americast 0899
Bell & Howell 0014
Bell South 0899
Director 0476
General Instrument 0003, 0476, 0810, 0276
GoldStar 0144
Hamlin 0009, 0273
Jerrold 0003, 0012, 0014, 0276, 0476,
0810
Memorex 0000
Motorola 0476, 1106, 0276, 0810
Pace 0237
Panasonic 0000, 0107
Paragon 0000
Philips 0305, 0317
Pioneer 0144, 0877, 0533, 1877
Pulsar 0000
Quasar 0000
Regal 0273, 0279
Runco 0000
Samsung 0144
Scientific Atlanta 0008, 0477, 0877, 0017, 1877
Sony 1006
Starcom 0003
Supercable 0276
Tocom 0012
Torx 0003
Toshiba 0000
Zenith 0525, 0000, 0899
Device Codes for Video Acc:
AOL 1061
Magnavox 1818
Mitsubishi 1002
Panasonic 1120
Page 81
81
INSTALLER
IR CODES
Philips 1818, 1061
Pioneer 1010
Princeton 0113, 0295
Samsung 1190, 1204
Sensory Science 1126
Sharp 1010
Sony 0850
Device Codes for SAT/DSS:
AlphaStar 0772
Chaparral 0216
Crossdigital 1109
Echostar 0775, 1005
Expressvu 0775
GE 0566
GOI 0775
General Instrument 0869
HTS 0775
Hitachi 0819
Hughes Net. Sys. 0749, 1142, 1749
JVC 0775
Magnavox 0724, 0722
Memorex 0724
Mitsubishi 0749
Motorola 0869
Next Level 0869
Panasonic 0247, 0701
Paysat 0724
Philips 0724, 0722, 1142, 0749, 1076,
1749
Proscan 0392
RCA 0566, 0143, 0855, 0392
RadioShack 0869
Samsung 1109
Sony 0639
Star Choice 0869
Toshiba 0749, 0790, 1749
Uniden 0724, 0722
Zenith 0856, 1856
Device Codes for VCRs:
Admiral 0048, 0209
Adventura 0000
Aiko 0278
Aiwa 0037, 0000
Akai 0041
America Action 0278
American High 0035
Asha 0240
Audiovox 0037
Beaumark 0240
Bell & Howell 0104
Broksonic 0184, 0121, 0209, 0002, 1479
CCE 0072, 0278
Calix 0037
Canon 0035
Carver 0081
Cineral 0278
Citizen 0037, 0278, 1278
Colt 0072
Craig 0037, 0047, 0240, 0072
Curtis Mathes 0035, 0060, 0760, 0162, 0041,
1035
Cybernex 0240
Daewoo 0045, 0278, 1278
Denon 0042
Dynatech 0000
Electrohome 0037
Electrophonic 0037
Emerex 0032
Emerson 0037, 0184, 0000, 0121, 1278,
1479, 0043, 0209, 0002, 0278,
0479
Fisher 0047, 0104
Fuji 0035
Funai 0000
GE 0035, 0060, 0760, 0048, 0240,
1035, 1060, 0807
Garrard 0000
Go Video 0432
GoldStar 0037, 0038, 1237
Gradiente 0000
HI-Q 0047
Harley Davidson 0000
Harman/Kardon 0081, 0038
Harwood 0072
Hitachi 0000, 0042, 0041
Hughes Net. Sys. 0042
JVC 0067, 0041
Jensen 0041
KEC 0037, 0278
KLH 0072
Kenwood 0067, 0041, 0038
Kodak 0035, 0037
LXI 0037
Lloyd's 0000
Logik 0072
MEI 0035
MGA 0240, 0043
MGN Technology 0240
MTC 0000, 0240
Magnasonic 0278, 1278
Magnavox 0035, 0039, 0081, 0000, 0149,
0563, 1781
Magnin 0240
Marantz 0035, 0081
Marta 0037
Matsushita 0035, 0162, 0454
Memorex 0035, 0037, 1037, 0048, 0039,
0047, 0162, 1162, 1262, 0000,
0240, 0104, 0209, 0454, 0479,
1237
Minolta 0042
Mitsubishi 0048, 0067, 0043, 0807
Motorola 0035, 0048
Multitech 0000, 0072
NEC 0067, 0104, 0041, 0038
Nikko 0037
Noblex 0240
Olympus 0035
Optimus 0037, 0048, 1048, 0162, 1062,
1162, 1262, 0104, 0454, 0432
Orion 0184, 0209, 0002, 0479, 1479
Panasonic 0035, 0225, 0162, 1062,
1035,1162, 1262, 0454, 0616
Penney 0035, 0037, 0042, 0240, 0038,
1035, 1237
Pentax 0042
Philco 0035, 0209, 0479
Philips 0035, 0081, 1081, 1181, 0618
Pilot 0037
Pioneer 0067
Polk Audio 0081
Profitronic 0240
Proscan 0060, 0760, 1060
Protec 0072
Pulsar 0039
Quasar 0035, 0162, 1162, 0454, 1035
RCA 0035, 0060, 0760, 0048, 1035,
1060, 0807, 0149, 0042, 0240
Radio Shack 1037, 0000
Radix 0037
Randex 0037
Realistic 0035, 0037, 0048, 0047, 0000,
0104
ReplayTV 0614, 0616
Runco 0039
STS 0042
Samsung 0045, 0240
Sanky 0048, 0039
Sansui 0000, 0067, 0209, 0041,
0479,1479
Sanyo 0047, 0240, 0104
Scott 0184, 0045, 0121, 0043
Sears 0035, 0037, 0047, 0000, 0042,
0104, 1237
Semp 0045
Sharp 0048, 0807, 0848
Shintom 0072
Shogun 0240
Singer 0072
Sonic Blue 0614
Sony 0035, 0032, 1032, 0000, 0636,
1232
Sylvania 0035, 0081, 0000, 0043, 1781
Symphonic 0000
TMK 0240
Tatung 0041
Teac 0000, 0041
Technics 0035, 0162
Teknika 0035, 0037, 0000
Thomas 0000
Tivo 0618, 0636
Toshiba 0045, 0043, 0845
Totevision 0037, 0240
Unitech 0240
Vector 0045
Vector Research 0038
Video Concepts 0045
Videomagic 0037
Videosonic 0240
Villain 0000
Wards 0035, 0060, 0760, 0048, 0047,
0081, 0000, 0042, 0240, 0072,
0149
White Westinghouse 0209, 0072, 0278, 1278
XR-1000 0035, 0000, 0072
Yamaha 0038
Zenith 0039, 0000, 0209, 0479, 1479
Device Codes for Laser Disc
Players:
Aiwa 0203
Denon 0059, 0172
Funai 0203
Mitsubishi 0059
NAD 0059
Optimus 0059
Panasonic 0204
Pioneer 0059
Quasar 0204
Page 82
82
INSTALLER
IR CODES
Realistic 0203
Sony 0201, 0193
Technics 0204
Device Codes for DVD Players:
Aiwa 0641
Apex Digital 0672, 0755, 0794, 0795, 0796,
0797, 0830
Blue Parade 0571
Broksonic 0695
Daewoo 0784
Denon 0490, 0634
Emerson 0591
Enterprise 0591
Fisher 0670
GE 0522
Go Video 0715, 0783
Gradiente 0651
Harman/Kardon 0582, 0702
Hitachi 0573, 0664
Hiteker 0672
JBL 0702
JVC 0558, 0623, 0867
Kenwood 0534, 0682
Konka 0711, 0719, 0720, 0721
Koss 0651
Lasonic 0798
Magnavox 0503, 0675
Malata 0782
Marantz 0539
Microsoft 0522
Mitsubishi 0521
Onkyo 0503, 0627
Oritron 0651
Panasonic 0490, 0632
Philips 0503, 0539, 0646, 0854
Pioneer 0525, 0571, 0632
Princeton 0674
Proscan 0522
RCA 0522, 0571, 0822, 1022
Rowa 0823
Sampo 0698
Samsung 0573, 0820
Sansui 0695
Sanyo 0670
Sharp 0630
Sherwood 0633
Sony 0533, 1533
Sylvania 0821
Technics 0490
Techwood 0692
Theta Digital 0571
Toshiba 0503, 0695, 1045
Urban Concepts 0503
Yamaha 0490, 0545, 0817
Zenith 0503, 0591
Device Codes for Tuner/Amp:
ADC 0531
Aiwa 1089, 1405, 0158, 1388
Alco 1390
Anam 1609
Apex Digital 1257
Audiotronic 1189
Audiovox 1390
Bose 1229
Capetronic 0531
Carver 1089, 1189
Denon 1104, 1160, 1360
JBL 1306
JVC 0074
KLH 1390
Kenwood 1313, 1027, 1570, 1569, 0027
Koss 1366
MCS 0039
Magnavox 1089, 1189, 0531
Marantz 1089, 1189, 0039
Musicmagic 1089
Onkyo 0135, 0842, 1298
Optimus 1023, 0531
Panasonic 1518, 0039, 1288
Philips 1089, 1189, 1269, 1283
Pioneer 0014, 0531, 1023
Proscan 1254
Quasar 0039
RCA 1023, 1254, 0531, 1390, 1609
Samsung 1295
Sansui 1089
Sherwood 1653
Sony 1058, 1158, 1258, 0158
Stereophonics 1023
Sunfire 1313
Technics 1308, 1309, 1518, 0039
Thorens 1189
Venturer 1390
Victor 0074
Wards 0014, 0158
Yamaha 0176, 1176
Device Codes for Amp and
Misc. Audio:
Aiwa 0010, 0159
GE 0078
Harman/Kardon 0892
Jerrold 0520, 0459
JVC 0331
Left Coast 0892
Marantz 0892
Optimus 0395
Philips 0892
Polk Audio 0892
Realistic 0395
Scientific Atlanta 0460
Sony 0010, 0159
Soundesign 0078
Starcom 0459
Victor 0331
Wards 0078
Yamaha 0354
Device Codes for CD Players:
Aiwa 0157
California Audio Labs 0029
Carver 0157, 0179
Classic 1297
DKK 0000
DMX Electronics 0157
Denon 0873
Emerson 0305
Fisher 0179
GPX 1296
Genexxa 0032, 0305
Harman/Kardon 0157, 0173
Hitachi 0032
JVC 0072, 1294
Kenwood 0826, 0626, 0028, 0037, 0681
Koss 1317
Krell 0157
LXI 0305
Linn 0157
MCS 0029
Magnavox 0157, 0305
Marantz 0626, 0029, 0157
Miro 0000
Mission 0157
NSM 0157
Onkyo 0868
Optimus 1063, 0032, 0000, 0179, 0305,
0037
Panasonic 0029
Philips 0626, 0157
Pioneer 1063, 0032, 0305, 1062
Polk Audio 0157
Proton 0157
QED 0157
Quasar 0029
RCA 0179, 0305, 0032, 1062
Realistic 0179
Rotel 0157
SAE 0157
Sansui 0157, 0305
Sanyo 0179
Scott 0305
Sears 0305
Sharp 0861, 0037
Sherwood 1067
Sonic Frontiers 0157
Sony 0490, 0000, 0100
TDK 1208
Technics 0029
Victor 0072
Wards 0157
Yamaha 0888, 1292
Device Codes for Home
Control:
Audio Access 0154
Cableshare 0537
Comfortex 0400
Da-Lite 0780
Elero 0434
Evergo 0059
GE 0240
Gewa 0095
Holmes 1215
Hunter Douglas 0433
Lightolier 0184, 1204, 1205, 1206
LiteTouch 0084
Lutron 0597, 0318, 1239, 1597
One For All 0167
RadioShack 0240
Russound 1232, 1233
Sanyo 0336
Security System 0167
Somfy 0780
Universal X10 0167
X10 0167
Page 83
83
INSTALLER
KEY CODES
TV (HDTV)
KEY FUNCTION UNO-S1 TV (HDTV)
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV/Video
TV/DSS TVDSS Learned Only
Play Play Learned Only
Stop Stop Learned Only
Search Fwd SrchF Learned Only
Search Rev SrchR Learned Only
KEY FUNCTION UNO-S1 TV (HDTV)
Pause Pause Learned Only
Record Recrd Learned Only
Menu Menu Menu (Picture)
Menu Up MenuU Menu Up, Adjust Up
Menu Dn MenuD Menu Dn, Adjust Dn
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select
Exit Exit Exit, Cancel
Display Displ Display, OSD, Info
Guide Guide Guide
Page Up PageU Adjust up
Page Down PageD Adjust Down
Disk Disk Learned Only
Plus 10 Pls10 +100
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Learned Only
Track Rev TkRev Learned Only
Sur On/Off SurOn Surround On/Off
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M PIP Move
PIP Swap PIP S PIP Swap
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 84
84
KEY FUNCTION UNO-S1 TV (HDTV)
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External Antenna
Live/Intro Intro Learned Only
Menu Menu Menu (Audio)
Back Back Back
Fav Channel FavCh Favorite
Display Fmt DFrmt Fmt,Wide,16:9,Aspct
SAP SAP SAP, CC
Slow Slow Learned Only
PIP On PIPOn PIP ON
PIP Off PIPOf PIP OFF
PIP Freeze PIPFr PIP Freeze
PIP Input PIPIn PIP Input
KEY FUNCTION UNO-S1 TV (HDTV)
PIP Chan Up PIPCU PIP Channel Up
PIP Chan Dn PIPCD PIP Channel Down
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6 In 6
VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
TV (HDTV)
Page 85
85
INSTALLER
KEY CODES
CABLE
KEY FUNCTION UNO-S1 CABLE
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input Bypass, A/B
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 CABLE
Pause Pause Pause
Record Recrd Record
Menu Menu Menu, Settings
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Down
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select
Exit Exit Exit, Cancel
Display Displ Info, Display, OSD
Guide Guide Guide
Page Up PageU Page Up
Page Down PageD Page Down
Disk Disk Learned Only
Plus 10 Pls10 +100
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Quick Skip,Advance
Track Rev TkRev Instant Replay
Sur On/Off SurOn Day Down
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 86
86
KEY FUNCTION UNO-S1 CABLE
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External AV Source
Live/Intro Intro Return to Live
Menu Menu PPV (Wink)
Back Back Back
Fav Channel FavCh Favorite
Display Fmt DFrmt Help
SAP SAP Day Up
Slow Slow Learned Only
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 CABLE
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 A,VID1,Video,TVp1
Input 2 In 2 B,VID2,TVp2
Input 3 In 3 C,VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6 In 6
VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
CABLE
Page 87
87
INSTALLER
KEY CODES
VIDEO ACC
KEY FUNCTION UNO-S1 VIDEO ACC
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV/Video, DTV
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 VIDEO ACC
Pause Pause Pause
Record Recrd Record
Menu Menu Menu, Home
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Dn
Menu Left MenuL Menu Left
Menu Right MenuR Menu right
Select Sel Menu Select
Exit Exit Exit, Cancel, Go
Display Displ Info, Display, OSD
Guide Guide Guide, View
Page Up PageU Page Up, Scroll Up
Page Down PageD Page Dn, Scroll Dn
Disk Disk Learned Only
Plus 10 Pls10 +100. +10
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Skip Up, Next
Track Rev TkRev Skip Dn, Previous
Sur On/Off SurOn Learned Only
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M PIP Move
PIP Swap PIP S PIP Swap
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 88
88
KEY FUNCTION UNO-S1 VIDEO ACC
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr Ext. Antenna, Web
Live/Intro Intro Learned Only
Menu Menu Setup,Prgrm,Options
Back Back Learned Only
Fav Channel FavCh Favorites
Display Fmt DFrmt Fmt,Wide,16:9,Aspct
SAP SAP Language, MTS
Slow Slow Learned Only
PIP On PIPOn PIP ON
PIP Off PIPOf PIP OFF
PIP Freeze PIPFr PIP Freeze
PIP Input PIPIn PIP Input
KEY FUNCTION UNO-S1 VIDEO ACC
PIP Chan Up PIPCU PIP Channel Up
PIP Chan Dn PIPCD PIP Channel Down
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5
VID5,AV1,VCR,BNC
Input 6 In 6
VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
VIDEO ACC
Page 89
89
INSTALLER
KEY CODES
SAT/DSS
KEY FUNCTION UNO-S1 SAT/DSS
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV/DSS/SAT
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 SAT/DSS
Pause Pause Pause
Record Recrd Record
Menu Menu Menu (PVR, Tivo)
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Down
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select
Exit Exit Exit, Cancel
Display Displ Info, Display, OSD
Guide Guide Guide
Page Up PageU Page Up,ThumbsUp
Page Down PageD Page Dn,ThumbsDn
Disk Disk Learned Only
Plus 10 Pls10 +100
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Quick Skip,Advance
Track Rev TkRev Instant Replay
Sur On/Off SurOn Learned Only
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 90
90
KEY FUNCTION UNO-S1 SAT/DSS
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External AV Source
Live/Intro Intro Return to Live
Menu Menu Menu (DTV)
Back Back Back
Fav Channel FavCh Favorite
Display Fmt DFrmt Fmt,Wide,16:9,Aspct
SAP SAP Alt/Audio,Lang.,CC
Slow Slow Slow
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 SAT/DSS
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6 In 6
VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
SAT/DSS
Page 91
91
INSTALLER
KEY CODES
VCR
KEY FUNCTION UNO-S1 VCR
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mutte Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV/VCR
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 VCR
Pause Pause Pause
Record Recrd Record
Menu Menu Menu (PVR,Tivo)
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Down
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select
Exit Exit Exit, Cancel
Display Displ Display, OSD, Info
Guide Guide Guide,VCR+,Prgrm
Page Up PageU Thmubs Up
Page Down PageD Thmubs Down
Disk Disk Learned Only
Plus 10 Pls10 +100
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd
QuickSkip/Adv,Indx TrkUp
Track Rev TkRev
Instnt Rplay,Indx Trk Dn
Sur On/Off SurOn Learned Only
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 92
92
KEY FUNCTION UNO-S1 VCR
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr Input Select
Live/Intro Intro
Return to Live,Auto Track
Menu Menu Menu
Back Back Clear
Fav Channel FavCh
Replay Zones, Indx Mark
Display Fmt DFrmt Record Speed
SAP SAP SAP, CC
Slow Slow Slow
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 VCR
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6
In 6 VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
VCR
Page 93
93
INSTALLER
KEY CODES
LASER DISC
KEY FUNCTION UNO-S1 LASER DISC
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 5Digit 5
6 6 6Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Learned Only
Channel Dn Ch Dn Learned Only
Power Power Power On/Off
Enter Enter Learned Only
Prev Channel PrvCh Repeat
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A / B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV,LD,Input Select
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Chapter/Skip Up
Search Rev SrchR Chapter/Skip Dn
KEY FUNCTION UNO-S1 LASER DISC
Pause Pause Pause
Record Recrd Learned Only
Menu Menu Menu, Program
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Down
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select
Exit Exit Exit, Cancel
Display Displ Display, OSD, Info
Guide Guide Learned Only
Page Up PageU Disk Skip, Disk Up
Page Down PageD Disk Down
Disk Disk Learned Only
Plus 10 Pls10 +10
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Chapter/Skip Up
Track Rev TkRev Chapter/Skip Down
Sur On/Off SurOn Audio
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 94
94
KEY FUNCTION UNO-S1 LASER DISC
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr
Ext AV Src,CDV,VCD,Karaok
Live/Intro Intro Intro,Search,Scan
Menu Menu Learned Only
Back Back Learned Only
Fav Channel FavCh Mark
Display Fmt DFrmt Learned Only
SAP SAP Subtitle, CC
Slow Slow Slow
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 LASER DISC
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6
In 6 VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
LASER DISC
Page 95
95
INSTALLER
KEY CODES
DVD
KEY FUNCTION UNO-S1 DVD
1 1 Digit 1, Traack 1
2 2 Digit 2, Track 2
3 3 Digit 3, Track 3
4 4 Digit 4, Track 4
5 5 Digit 5, Track 5
6 6 Digit 6, Track 6
7 7 Digit 7, Track 7
8 8 Digit 8,Track 8
9 9 Digit 9, Track 9
0 0 Digit 0, Track 10
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Channel Up
Channel Dn Ch Dn Channel Down
Power Power Power On/Off
Enter Enter Channel Enter
Prev Channel PrvCh Last Channel,Repeat
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input TV/DVD,Input Select
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 DVD
Pause Pause Pause
Record Recrd Record
Menu Menu Disk Menu
Menu Up MenuU Menu Up
Menu Dn MenuD Menu Dn
Menu Left MenuL Menu Left
Menu Right MenuR Menu right
Select Sel Menu Select
Exit Exit Exit, Cancel, Return
Display Displ Display, OSD, Info
Guide Guide Title
Page Up PageU Disk Skip, Disk Up
Page Down PageD Disk Down
Disk Disk Learned Only
Plus 10 Pls10 +100. +10
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Chapter/Skip Up
Track Rev TkRev Chapter/Skip Down
Sur On/Off SurOn Audio, Language
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 96
96
KEY FUNCTION UNO-S1 DVD
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External AV Source
Live/Intro Intro Intro,Search,Scan
Menu Menu Setup Menu
Back Back Clear
Fav Channel FavCh Mark
Display Fmt DFrmt
Format Wide,Zoom,Aspect
SAP SAP Subtitle, CC
Slow Slow Slow
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 DVD
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 VID1,Video,TVp1
Input 2 In 2 VID2,TVp2
Input 3 In 3 VID3,TVp3
Input 4 In 4 VID4,TVp4
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6
In 6 VID6,AV2,VDP,DVD,DVI
Input 7 In 7 TV, Component
Input 8 In 8 CAB,SAT,S-Video
Input 9 In 9 AV, Tuner
Input 10 In 10 AUX, RGB
INSTALLER
KEY CODES
DVD
Page 97
97
INSTALLER
KEY CODES
RECEIVER
KEY FUNCTION UNO-S1 RECEIVER
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Preset Up
Channel Dn Ch Dn Preset Down
Power Power Power On/Off
Enter Enter 5.1, Prologic
Prev Channel PrvCh
Last Channel, Repeat
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input
DVD/Tuner,Input Select
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 RECEIVER
Pause Pause Pause
Record Recrd Record
Menu Menu Disk menu, Menu
Menu Up MenuU Menu Up, Adjust Up
Menu Dn MenuD Menu Dn, Adjust Dn
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel
MenuS elect, Continue
Exit Exit Exit, Cancel
Display Displ Display, OSD, Info
Guide Guide Title
Page Up PageU Adjust Up
Page Down PageD Adjust Down
Disk Disk Learned Only
Plus 10 Pls10 Band, FM/AM
Open/Close Op/Cl Learned Only
Random Randm Random
Track Fwd TkFwd Skip Up
Track Rev TkRev Skip Down
Sur On/Off SurOn
Srrd Mode/On Off,Aduo Lang
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 98
98
KEY FUNCTION UNO-S1 RECEIVER
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External AV Source
Live/Intro Intro Intro,Search,Scan
Menu Menu Menu
Back Back Clear
Fav Channel FavCh Mark
Display Fmt DFrmt
FormatWide,Zoom,Aspect
SAP SAP Learned Only
Slow Slow Slow
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 RECEIVER
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 CD
Input 2 In 2 Tuner
Input 3 In 3 DVD, LD
Input 4 In 4 VCR, VID1
Input 5 In 5 VID5,AV1,VCR,BNC
Input 6 In 6 TV, VID2
Input 7 In 7 LD, VID3
Input 8 In 8 AUX, VID4
Input 9 In 9 DAT, Cable
Input 10 In 10 Phono SAT
INSTALLER
KEY CODES
RECEIVER
Page 99
99
INSTALLER
KEY CODES
AMP/MISC AUDIO
KEY FUNCTION UNO-S1 AMP/MISC AUDIO
1 1 Digit 1
2 2 Digit 2
3 3 Digit 3
4 4 Digit 4
5 5 Digit 5
6 6 Digit 6
7 7 Digit 7
8 8 Digit 8
9 9 Digit 9
0 0 Digit 0
Volume Up VolUp Volume Up
Volume Down VolDn Volume Down
Mute Mute Mute
Channel Up Ch Up Preset Up
Channel Dn Ch Dn Preset Down
Power Power Power On/Off
Enter Enter 5.1, Prologic
Prev Channel PrvCh Repeat
TV/Video TVVid Learned Only
TV/VCR TVVCR Learned Only
A/B A/ B Learned Only
TV/DVD TVDVD Learned Only
TV/LD TV LD Learned Only
Input Input Bypass,Input Slct
TV/DSS TVDSS Learned Only
Play Play Play
Stop Stop Stop
Search Fwd SrchF Fast Forward
Search Rev SrchR Rewind
KEY FUNCTION UNO-S1 AMP/MISC AUDIO
Pause Pause Pause
Record Recrd Record
Menu Menu Menu, Program
Menu Up MenuU Menu Up, Adjust Up
Menu Dn MenuD Menu Dn, Adjust Dn
Menu Left MenuL Menu Left
Menu Right MenuR Menu Right
Select Sel Menu Select, Cont
Exit Exit Exit, Cancel
Display Displ Display, OSD, Info
Guide Guide Learned Only
Page Up PageU Adjust Up
Page Down PageD Adjust Down
Disk Disk Learned Only
Plus 10 Pls10 Band, FM/AM
Open/Close Op/Cl Learned Only
Random Randm Learned Only
Track Fwd TkFwd Skip Up
Track Rev TkRev Skip Down
Sur On/Off SurOn
Srrd Mode/On Off,Aduo Lang
Sur Mode SurMd Learned Only
Surround Up SurUp Learned Only
Surround Dn SurDn Learned Only
PIP PIP Learned Only
PIP Move PIP M Learned Only
PIP Swap PIP S Learned Only
Program Progm Learned Only
Sleep Sleep Learned Only
On On On, Power On/Off
Page 100
100
KEY FUNCTION UNO-S1 AMP/MISC AUDIO
Off Off Off, Power On/Off
11 11 Learned Only
12 12 Learned Only
13 13 Learned Only
14 14 Learned Only
15 15 Learned Only
16 16 Learned Only
Bright Brght Learned Only
Dim Dim Learned Only
Close Close Learned Only
Open Open Learned Only
Halt Halt Learned Only
AM/FM AM/FM Learned Only
Cue Cue Learned Only
Disk Up DiskU Learned Only
Disk Down DiskD Learned Only
Info Info Learned Only
External Src ExtSr External AV Source
Live/Intro Intro Intro,Search,Scan
Menu Menu Learned Only
Back Back Clear
Fav Channel FavCh Learned Only
Display Fmt DFrmt Learned Only
SAP SAP Learned Only
Slow Slow Learned Only
PIP On PIPOn Learned Only
PIP Off PIPOf Learned Only
PIP Freeze PIPFr Learned Only
PIP Input PIPIn Learned Only
KEY FUNCTION UNO-S1 AMP/MISC AUDIO
PIP Chan Up PIPCU Learned Only
PIP Chan Dn PIPCD Learned Only
Input 1 In 1 CD
Input 2 In 2 Tuner
Input 3 In 3 DVD, LD
Input 4 In 4 TAPE, MD
Input 5 In 5 VCR, VID1
Input 6 In 6 TV, VID2
Input 7 In 7 LD, VID3
Input 8 In 8 AUX, VID4
Input 9 In 9 DAT, Cable
Input 10 In 10 Phono, SAT
INSTALLER
KEY CODES
AMP/MISC AUDIO
Loading...