Russound btc-1x User Manual

BTC -1x

Bluetooth® Remote Transceiver

Overview

BTC-1X Remote Transceiver accessory enables
the user the ability to wirelessly stream source
content from any Bluetooth enabled device to
a Russound multiroom audio system. The BTC­1X connects via a single CAT 5 RJ-45 terminated
cable. The CAT-5 cable carries power and balanced
audio signals to the Bluetooth RJ-45 jack on the
Russound multiroom products. The compact BTC­1X transceiver can sit on a  at sur face, hide behind
other equipment or be placed in a standard
electrical box behind a wall-plate. This versatility
allows for the Bluetooth transceiver to be placed
in the most optimal position. Most Bluetooth
products have very limited range based on near
 eld usage. With the BTC-1X the user can listen to
streaming wireless music and move throughout
the listening area without interruption.

The BTC-1X can also be programmed using a
micro USB cable. This feature o ers a speci c
security code and the ability to name each BTC­1X connected in the system. This is handy when
multiple Bluetooth transceivers are wired in close
proximity to each other.

Safety Instructions

1. Read Instructions - All the safety and operating

instructions should be read before the equipment is operated.

2. Retain Instructions - The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the equipment in the

operating instructions should be adhered to.

4. Follow Instructions - Follow all operating and user

instructions.

5. Water and Moisture - The equipment should not be used
near water; for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool.

6. Mounting - The equipment should be mounted or
secured as recommended by the manufacturer.

7. Heat - The equipment should be situated away from
heat sources such as radiators, heat registers, stoves, or other
equipment (including ampli ers) that produce heat.

8. Power Sources - The product should be connected to
a power supply only of the type described in the operating
instructions or as marked on the equipment.

9. Grounding or Polarization - Precaution should be taken
so that the grounding or polarization means of the product
is not defeated.

10. Avoid spills and foreign objects. Ensure liquids and
objects don’t get into the product enclosure through any
openings.

11. Damage Requiring Service - The equipment should
be serviced by quali ed service personnel when: the power
supply cord or the plug has been damaged; objects have
fallen, liquid has been spilled into the equipment; the
equipment has been exposed to rain; the equipment does
not appear to operate normally; or the equipment has been
dropped or the enclosure is damaged.

12. Servicing - The user should not attempt to service
the equipment beyond that described in the operating
instructions. All other servicing should be referred to quali ed
service personnel.

13. Care – From time to time you should wipe any dust
accumulation from the equipment with a soft dry cloth.

Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one of
or more of the following measures: reorient or relocate the
receiving antenna; increase the separation between the
equipment and receiver; connect the equipment into an
outlet on a circuit di erent from that to which the receiver
is connected, or consult the dealer or an experienced radio/
TV technician for help.

This Class B digital apparatus complies with Canadian ICES-

003.

Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.

Copyright ©2014 Russound® All rights reserved. All
trademarks are the property of their respective owners.
Russound is not responsible for typographical errors or
omissions. Speci cations are subject to change without
notice.

The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Russond is under license. Other trademarks and
trade names are those of their respective owners.

© 2014 CSR plc and its group companies. The aptX® mark
and the aptX logo are trade marks of CSR plc or one of its
group companies and may be registered in one or more
jurisdictions.

Russound, Inc.

5 Forbes Rd., Newmarket, NH 03857, USA
tel [phone] • fax [phone] www.russound.com
technical support: 866.888.7466
e-mail: [e-mail]

28-1384 06.06.14

Limited Warranty

The Russound BTC-1x is fully guaranteed for two (2) years
from the date of purchase against all defects in materials
and workmanship. During this period Russound will replace
any defective parts and correct any defect in workmanship
without charge for either parts or labor. For this warranty
to apply, the unit must be installed and used according
to its written instructions. If service is necessary, it must be
performed by Russound. Russound assumes no responsibility
for defects resulting from abuse or servicing performed by
an agency or person not speci cally authorized in writing
by Russound. Damage to or destruction of components due
to improper use voids the warranty. In these cases the repair
will be made at the owner’s expense. Accidental damage
and shipping damage are not considered defects under the
terms of the warranty. To return for repairs, the unit must be
shipped to Russound at the owner’s expense, along with a
Return Authorization number and documentation explaining
the nature of the service required. Any product returned
without prior written permission will be returned to sender.
Russound sells products only through authorized Dealers
and Distributors to ensure that customers obtain proper
support and service. Any Russound product purchased from
an unauthorized dealer or other source, including retailers,
mail order sellers and online sellers will not be honored or
serviced under existing Russound warranty policy. Any sale
of products by an unauthorized source or other manner
not authorized by Russound shall void the warranty on the
applicable product.

To obtain Return Authorization please contact us at:
[e-mail]

BTC-1x_Manual.indd 1BTC-1x_Manual.indd 1 6/5/14 3:08 PM6/5/14 3:08 PM

Testing

Verify the green LED is lit on the BTC-1X Remote

Transceiver.

Turn on a Bluetooth® enabled source i.e. media player,
smartphone, or computer. Open the Bluetooth menu
and enable the pairing feature on the device. Select the
Russound BTC-1X product by its con gured name from
the list of available Bluetooth enabled products. Enter PIN
number 0000 to complete pairing.

Select the desired audio from the device and start the
playback.

Connection Instructions

Read all instructions before starting the installation.

1. Determine the ideal location of the BTC-1X within the
room

2. Wire the CAT-5 from the controller to the BTC-1X
location

3. Add RJ-45 connectors to the CAT-5, follow the RJ-45
T568A Wiring Standard (show diagram)

4. Plug in each end of the RJ-45 into the appropriate jack
on the controller labeled Bluetooth and the BTC-1X RJ­45 jack.

5. If you are planning more than one BTC-1X in a home,
it is suggested that you program each BTC-1X. Follow
the programming instructions noted below.

Programming instructions

The BTC-1X comes con gured with the Name Russound
and Passkey 0000. To create a more secure network, it is
recommended that a unique Name and Passkey be created
at the time of installation and provided to the homeowner.

Follow the steps below to create a unique Name and
Passkey for each BTC-1X.

Note: CAT-5 cable must be connected during
programming to provide power to BTC-1X.

1. Plug in the micro USB cable (included) to the USB
programming port in the BTC-1X. (see diagram)

2. Connect the micro USB cable to the USB port on the PC.

3. Download the BSK-1 programming software from the
dealer portal at www.russound.com.

4. Launch the BTC-1X Con guration Tool software.

5. Enter a unique Name and a numeric Passkey (minimum
4 digits), then Write to device.

6. Disconnect the micro USB cable from the BTC-1X  rst,
then cycle the power on the BTC-1X by removing the
CAT-5. Cycling the power will reboot the BTC-1X with
the assigned custom Name and Passkey.

Connection Diagram

Bluetooth

CAT-5 Jack

Power LED

Programming

USB Port

BTC-1X

BTC-1X

Bluetooth CAT-5 Jack
on Russound controller

Speci cations

BTC-1X Remote Transceiver

Power requirements: supplied by controller via CAT-5

Frequency: 2,400-2,483.5 MHz
CAT-5 connection: RJ-45 (T568A standard)
Dimensions: 70mm x 56mm x 26mm (W x D x H)
Weight: 3.1 ounces
Max cable length: 300’ (CAT-5) BTC-1X to controller

50', (15M) without obstruction

Source Con guration

The BTC-1X is supported by Russound controllers with
Bluetooth capability.

Refer to the Russound controller instruction manuals to
connect and enable the Bluetooth source input.

Important Considerations

1. Disconnect the power cord to Russound controller
before making any connections to the BTC-1X.

2. Verify all connections are correct and polarity on the
connectors are correct. Follow T568A connections on
all RJ-45 connections as show in the diagram.

3. Keep all power cords away from all signal cables.
If you have to cross power cables, do so at 90 degrees
and don’t run the cables parallel with one another.
Keep a distance of 12” away if running parallel to
avoid induced noise on the CAT-5 cable.

4. Choose reliable signal cable and / or patch cords.

BTC-1x_Manual.indd 2BTC-1x_Manual.indd 2 6/5/14 3:08 PM6/5/14 3:08 PM