Russound 858P PLASMA IN-WALL User Manual
LIMITED WARRANTY
The Russound 858P Plasma In-Wall IR Receiver is fully guaranteed for two (2) years from
the date of purchase against all defects in materials and workmanship. For this warranty
to apply, the unit must be installed and used according to its written instructions. During
this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. Accidental damage and shipping damage are
not considered defects under the terms of this warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not
specifically authorized in writing by Russound. If service is necessary, it must be performed
by Russound. Damage to or destruction of components due to excessive power voids the
warranty. In these cases, the repair will be made at the owner’s expense. To return for
repairs, the unit must be shipped to Russound at the owner’s expense, along with a note
explaining the nature of the service required. Be sure to pack in a corrugated container
with at least 3 inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return
Authorization number. Write the RA number on the shipping label and ship to: Russound,
ATTN: Service, 5 Forbes Road, Newmarket NH 03857
Russound sells product only through authorized Dealers and Distributors to ensure that
customers obtain proper support and service. Any Russound product purchased from an
unauthorized dealer or other source, including retailers, mail order sellers and online sellers
will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void
the warranty on the applicable product.
5 Forbes Rd. Newmarket, NH 03857, USA
Tel 603.659.5170 • Fax 603.659.5388
e-mail: tech@russound.com
SaphIR
858P Plasma In-Wall
Decora®Style Infrared Receiver
Plasma and CFL Friendly
Instruction Manual
Decora®is a trademark of Leviton Corporation
Patented
PRODUCT OVERVIEW
The 858P Plasma In-Wall IR Receiver receives IR signals from a handheld IR
remote control and relays these signals to the audio/video equipment for
operation from another room. Mounts to a single gang J-Box using a
Decora
®
cover plate.
FEATURES
• Plasma-friendly - can be placed near plasma TVs and displays.
• CFL-friendly - allows installations in areas with compact fluorescent
lighting. Works in most lighting environments.
• Stylish Decora
®
design. Available in white, almond, bone, black or brown.
• Dual color LED. Green for system status and blue for talkback.
• Ultra thin design. Mounts easily in any J-box or P-ring.
• Wide band IR. Receives IR from many types of remotes.
WIRE CONNECTIONS - SHIELDED CABLE
The 858P Plasma In-Wall can be connected to the 857 connecting block
using shielded 2-twisted pair wire (AW2260AB). Use one pair to connect
GND (GROUND) and IR (SIGNAL). Use the other pair to connect ST (STATUS)
and V+ (+12VDC). Connect the shield or drain to the ground at the connect-
ing block ONLY, leaving the shield or drain disconnected at the 858P.
Connecting in this method will help reduce induced noise. See Figure 1 for
detail of these connections.
Figure 1
08/12/04
BLOCK
Wiring Configuration for 2-twisted pair shielded wire with drain
CONNECTING
857
DESIGNED IN USA MADE IN KOREA
EMITTER PORTS
EMITTERS
123456
ONFIRM
IR C
LOCK
B
NFRARED
857 I
ONNECTING
C
I
N
I
N
OMMON
ECEIVER
12VDC
+
P
OWER
12VDC
+
S
TATUS
SIGNAL
STATUS
GND
+
12VDC
IR C
IR R
12 VDC
TO GROUND
SHIELD WIRED
(AW2260AB)
PAIR WIRE
2-TWISTED
SHIELD
DO NOT
SUPPLY
846C POWER
CONNECT TO
CONNECT
(BACK)
IR RECEIVER
ST IR GND V+
858P PLASMA IN-WALL
IR RECEIVER
Figure 4
Figure 3
STATUS INDICATOR
To use the status indicator on the 858P Plasma In-Wall, connect the 12VDC
100mA or higher power supply to the STATUS line of the 857 connecting
block as shown in Figure 3.
STATUS ON
STATUS OFF
Figure 5
MOUNTING
Mount the 858P Plasma In-Wall to the J-Box using the screws that are supplied. Mount the cover plate (not included) to the IR receiver. See Figure 5.
SPECIFICATIONS
Receive Frequency: 36kHz to 58kHz
Transmit Frequency: 40kHz and 56kHz
Range: On Axis – 55ft to 80ft
30º Off Axis – 30ft to 55ft
Power: 12VDC 31mA max
Status Power: 12VDC 3mA max
Wire requirements: 2 twisted pair, with or without shield
Dimensions: 1
3
/4”W x 4 5/16”H x 3/8”D
Weight: 1/2oz
Plug the power supply into the switched outlet on the stereo receiver. When
the receiver is on, the power supply will turn on the system status line and
illuminate the LED Green of the 858P Plasma In-Wall. The status line can be
turned on or off by setting the jumper on back of the 858P Plasma Wall as
shown in Figure 4.
WIRE CONNECTIONS - CAT-5e
The connection between the IR receiver and the connecting block can be
made with twisted-pair wiring (i.e., CAT-5e cable). It may be necessary to use
shielded twisted-pair wiring if the wiring is exposed to interference from
power wiring centers or from broadcast signals (FM, TV, etc.) located nearby.
The installer should determine the cable type needed to suit the local conditions of the installation. See Figure 2.
Figure 2
858P CAT-5e 857
ST OR/ORW STATUS
IR BL SIGNAL
(OPEN) BLW GND
GND BR/BRW GND
V+ GR/GRW +12VDC
858P PLASMA
IN-WALL
IR RECEIVER
(BACK)
Brown
Brown/White
12 VDC
Leave
Blue/White
open at 858P
Orange/White
Orange
Blue
Blue/White
ST IR GND V+
Green
Green/White
12 VDC
C
S
TATUS
+
12VDC
P
OWER
+
12VDC
IR R
ECEIVER IN
IR C
OMMON IN
+
12VDC
GND
STATUS
SIGNAL
DESIGNED IN USA MADE IN KOREA
ONNECTING
B
LOCK
IR C
ONFIRM
857
CONNECTING
BLOCK
123456
857 I
NFRARED
EMITTERS
EMITTER PORTS
C
CAT-5e cable
Drain
Blue/White to
GND on 857
Green
Green/White
Orange/White
Orange
Brown
Brown/White
Blue
IR R
IR C
+
12VDC
GND
STATUS
SIGNAL
S
TATUS
+
12VDC
P
OWER
+
12VDC
ECEIVER IN
OMMON IN
ONNECTING
857 I
NFRARED
B
LOCK
IR C
ONFIRM
DESIGNED IN USA MADE IN KOREA
CONNECTING
123456
EMMITERS
857
BLOCK
EMITTER PORTS
ST IR GND V+
ST IR GND V+
Loading...