Russound 854P User Manual

SaphIR

854P

Mini Tabletop Infrared Receiver

Instruction Manual

LIMITED WARRANTY

The Russound 854P IR Receiver is fully guaranteed for two (2) years from the date of
purchase against all defects in materials and workmanship. For this warranty to apply,
the unit must be installed and used according to its written instructions. During this
period, Russound will replace any defective parts and correct any defect in workman­ship without charge for either parts or labor. Accidental damage and shipping damage
are not considered defects under the terms of this warranty. Russound assumes no
responsibility for defects resulting from abuse or servicing performed by an agency or
person not specifically authorized in writing by Russound. If service is necessary, it
must be performed by Russound. Damage to or destruction of components due to
excessive power voids the warranty. In these cases, the repair will be made at the
owner’s expense. To return for repairs, the unit must be shipped to Russound at the
owner’s expense, along with a note explaining the nature of the service required. Be
sure to pack in a corrugated container with at least 3 inches of resilient material to
protect the unit from damage in transit.

Before returning a unit for repair, call Russound at [phone] for a Return
Authorization number. Write the RA number on the shipping label and ship to:
Russound, ATTN: Service, 5 Forbes Road, Newmarket NH 03857

Russound sells product only through authorized Dealers and Distributors to ensure that
customers obtain proper support and service. Any Russound product purchased from
an unauthorized dealer or other source, including retailers, mail order sellers and
online sellers will not be honored or serviced under existing Russound warranty policy.
Any sale of products by an unauthorized source or other manner not authorized by
Russound shall void the warranty on the applicable product.

5 Forbes Rd. Newmarket, NH 03857, USA

Tel [phone] • Fax [phone]

e-mail: [e-mail]

PRODUCT OVERVIEW

The 854P Plasma Tabletop IR Receiver receives IR signals from a
handheld IR remote control and relays these signals to the audio-video
equipment for operation from another room. The receiver has a non­skid base and is placed on a flat surface.

FEATURES

•Plasma-friendly - can be placed near plasma TV and displays

•CFL friendly - allows installations in areas with compact fluorescent
lighting. Works in most lighting environments.

•Blue IR confirmation LED

•Wide band IR receives IR from many types of remotes

•Non-skid base

•84.65” cable with 1/8” (3.5mm) stereo mini-plug

WIRE CONNECTIONS

Conductors on 1/8” (3.5mm) stereo mini-plug

28-1208 09/27/05

SPECIFICATIONS

Receive Frequency Range: 36kHz to 58kHz

Transmit Frequencies: 40kHz and 56kHz

Range: On Axis – 40ft to 50ft (12.2-15.2m)

30º Off Axis – 5ft to 20ft (1.5-6.1m)

Power: 12VDC 31mA max.

Dimensions: 2.125”W x 0.688”H x 1.625”D

(54 x 17.5 x 41.3mm)

Cord Length: 84.65” (215cm)

Connector Type: 1⁄8” (3.5 mm) TRS mini plug

Finish: Black

SEE REVERSE SIDE FOR INSTALLATION INSTRUCTIONS

SIGNAL

Tip

GND

Ring
+12VDC
Sleeve

INSTALLATION

The 854P is used in two typical installations: Direct (connected directly to an
IR connecting block, e.g., 857) and Remote (remote mounting using an inter­face, e.g., IRB-1 in-wall connecting block).

In both installations, the 854P may be connected to the IR RECEIVER IN jack
using the 1/8” (3.5mm) stereo mini-plug. In remote installations, it may be
preferable to hard wire to the 4-position termination plug on the 857 or IRB-6
connecting block.

854P IR RECEIVER

DIRECT
INSTALLATION

REMOTE
INSTALLATION

846C 12VDC
POWER SUPPLY

C

S

TATU S

+

12VDC

P

OWER

+

12VDC

IR R

ECEIVER IN

IR C

OMMON IN

+

12VDC

GND

STATUS

SIGNAL

DESIGNED IN USA MADE IN CHINA

ONNECTING

857 I

NFRARED

B

LOCK

IR C

ONFIRM

123456

E

MITTERS

IR RECEIVER CONNECTION

IRB-1 CONNECTING BLOCK

AW2260AB 22 GAUGE

4 CONDUCTOR WIRE

854P IR RECEIVER

857 CONNECTING BLOCK