Russell Hobbs RHPF-40 Instructions And Warranty Information

INSTRUCTIONS AND WARRANTY

MODEL: RHPF-40

RUSSELL HOBBS PEDESTAL FAN

INTRODUCTION

Thank you for purchasing the Russell Hobbs RHPF-40 Oscillating Pedestal fan. Each unit has
been manufactured to ensure safety, reliability & ease of use. Before use, please read these
instructions carefully, and keep them for further reference.

IMPORTANT SAFEGUARDS

When using your Russell Hobbs fan, basic precautions should always be followed including the
following:

1. Make sure the power used corresponds to the one indicated on the rating label.

2. Use the fan only for use as described in this instruction manual.

3. To protect against electrical shock, do not place fan in front of a window.

4. Do not cover.

5. Do not immerse unit, plug or cord in water or allow for liquid to come into contact with any
part of the fan.

6. Close supervision is necessary when any appliance is used by or near children.

7. Unplug the fan from the power supply when: not in use, when moving from one location
to another, before putting on or taking off parts and before cleaning.

8. Avoid coming into contact with any moving part.

9. To avoid vibration, place the fan on a smooth level surface.

10. Never operate the fan with a damaged power cord or plug, or after it has fallen or
damaged in any way.

11. Do not allow objects to fall into the openings and do not insert objects through the guard
when the fan is in operation.

12. Do not operate without fan grilles properly in place.

13. Do not use outdoors.

14. Do not let cord hang over edge of table or counter, or touch hot surfaces.

15. To disconnect, grip plug, and pull from wall outlet. Never pull on the cord.

16. Do not try to cover, extend or stretch the mains cable.

17. Never attempt to open any part or dismantle the controls. Responsibility for failure cannot
be accepted if this instruction has been ignored.

18. This product is intended for household use only. Industrial or commercial use invalidates
the warranty.

PARTS NAME & LOCATION

ASSEMBLY INSTRUCTIONS

Your Russell Hobbs Fan has been boxed unassembled to minimize packaging waste. Each part
fits together easily and can be removed for cleaning, and storage.

1. Take the fan out of the box and remove any protective wrappings.

2. Place all the parts on the floor.

3. Remove the four position screws on the base, align the base with the four holes on the
holding plate, insert the four position screws and tighten.

4. Remove the four position screws on the motor and align the rear guard with the four
holes on the motor (handle facing top of the fan) insert the four position screws and
tighten.

5. Loosen the set screw on the blade; slide the blade on to the shaft of the motor. Tighten
the set screw on to the flat side of the shaft to secure the blade ensuring the blade does
not damage the guards.

6. Assemble the front guard to the rear guard. Tighten the connecting screw and nut;
thereafter secure the retaining clips.

OPERATING INSTRUCTIONS

1．The on/off switch is incorporated in the speed control switch on the head of the fan.

2． Your Russell Hobbs fan control has three speed settings. The various speed settings

assist in regulating the airflow from the fan:

0 The fan is switched off.
1 The fan operates at the lowest speed.
2 The fan operates at the medium speed.
3 The fan operates at the highest speed.

3． The fan can operate in oscillation or static mode;
4． To make the fan head oscillate, push down the Oscillation Knob.
5． To stop the fan head from oscillating pull the Oscillation Knob up.
6． The head of the fan can be adjusted up or down - to do this unplug unit, loosen the

adjusting knob; adjust the fan to the desired angle. To secure tighten the Adjusting
Knob.

CLEANING

1. Before cleaning, always ensure the fan is switched off and disconnected from the
electrical socket.

2. Wipe off dust and dirt with a warm moist cloth and then buff with dry cloth.

3. Do not immerse the fan in water or other fluids.

CONNECTING THE 3-PIN PLUG

Should the need arise to change the fitted/moulded plug, follow these instructions:

Mains (AC) Operation

This unit is designed to operate on 230V current only. Connecting to other power
sources may damage the unit.
Connect three-pin plug as follows:

The wires in this mains lead are coloured in accordance with the following:
Green/Yellow = Earth Blue = Neutral Brown = Live

NOTE: This appliance is a class two product and as such does not have an Earth
wire. Please follow the above instructions leaving out the connection for the Earth
wire.

PROBLEM SOLVING

There are no user serviceable parts in this appliance. If the appliance is not operating correctly,
please check that:

1. You have followed the instructions correctly.

2. The unit has been wired correctly and the wall socket is switched on.

3. The mains power supply is ON.

If the appliance still does not work:
In the first instance, consult your retailer for possible repair or replacement. If your retailer fails to
solve your problem and you need to return the appliance, make sure that:

1. The unit is packed carefully and complete into its original packaging.

2. Proof of purchase is attached.

3. Give the reason why you are returning it.

If the supply cord is damaged, it must be replaced by the manufacturer or its Service Agents in
order to avoid a hazard. If service should become necessary within the warranty period, the
appliance should be returned to an approved Home of Living Brands (PTY) LTD service center.
Servicing outside the warranty period is still available, however this will be chargeable. If the

power supplies cord becomes damaged the manufacturer or an approved service agent must
replace it.