Russell Hobbs RHOFR5001 (B), RHOFR5002 (B) User Manual

Page 1
Oil Filled Radiator
For Customer Services & Spare Parts please call 0345 209 7461
Or visit us at https://mda.russellhobbs.com
PLEASE RETAIN
FOR FUTURE REFERENCE
Model Number: RHOFR5001 (B) 1500W RHOFR5002 (B) 2000W
This product is only suitable for well insulated spaces or occasional use
Page 2
Page(s)
Unpacking
your appliance
3
Safety
Instructions
3-6
Feature
Diagram
7
Base
Assembly
8
Using
your Oil Filled Radiator
9 - 11
Cleaning
and Care
12
Problem
Solving
13
Guarantee
and Customer Services
14
Spare
Parts
15
Connection
to the Mains Supply
16
Specification
17-18
Notes
19
Disposable
Information
20
CONTENTS
Page 2
Page 3
UNPACKING YOUR APPLIANCE
Before you use your appliance
1. Remove all the packaging.
2. Check the appliance after unpacking for any visual damage such as:
Misaligned or damaged parts
Damage to the controls
Damage to the plug or cable
If you can see any damage do not use the appliance
The appliance should not be used if it has been dropped or there are any visible signs
of damage.
This appliance must be placed on a solid stable surface, away from walls, cabinets, furniture, curtains, etc. Position the appliance with minimum spacing of 100cm from the top and sides, front and back.
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be observed, including the following:
Read all instructions.
Check that the mains voltage corresponds with the rating on
the appliance.
The appliance must not be left unattended while it is connected to the mains supply.
Do not touch hot surfaces. Use the handle or the controls.
To protect against electrical shock do not immerse cord, plug, or
appliance in water or other liquid. Do not operate with wet hands.
Do not let the cord hang over the edge of a worktop, table etc. or touch hot surfaces.
Page 3
Page 4
SAFETY INSTRUCTIONS
Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. The supply cord can not be replaced. If the cord is damaged the appliance should be scrapped.
The use of accessory attachments not recommended by the appliance manufacturer may cause fire, electric shock or injury.
This appliance must not be immersed in any liquid
To disconnect, remove the plug from the mains outlet. Do not
pull the plug out by the cord.
Warning: In order to avoid overheating, do not cover the heater.
Never remove parts from the appliance, such as the feet,
screws and so on.
Never use the appliance near a bath, shower or a swimming pool.
Never place flammable objects or clothing on top of the appliance.
Allow a 100cm safe area around the appliance on the top and sides, front and back.
Never use the appliance in a room with explosive gas such as petrol, or while using any kinds of flammable glues, sprays or solvents.
Prevent overheating of the appliance by keeping the air inlets
and outlets clean and free of anything that may cause blockage.
Check all inlets and outlets regularly for accumulated dust. DO NOT COVER.
Do not place any part of your body near the air inlet, outlet or on the fins ,to avoid personal injury, electric shock or fire.
If overheating should occur, the built-in overheating safety device will shut the appliance off. Note, the appliance will turn on again when it has cooled down sufficiently.
Page 4
Page 5
SAFETY INSTRUCTIONS
Do not insert any foreign objects into the ventilation.
Keep all ventilation clear of any draped fabric or curtains.
The appliance must not be located immediately below a mains
socket. Do not use the appliance with a programmer, timer or any other device that switches the appliance on automatically. A
fire risk exists if the appliance is covered or positioned
incorrectly.
Caution: Some parts of this product can become very hot and cause burns. Particular attention must be given when children or vulnerable people are present.
Do not operate this appliance for anything other than its intended use.
This appliance is not intended for commercial use.
This product is intended for household use only. Do not use
outdoors.
This product is only intended for heating.
Warning: It is hazardous for anyone other than a competent
person to carry out any service or repair operation which involves the removal of a cover which gives protection against exposure to electrical parts.
This heater is filled with a precise quantity of special oil. Repairs
requiring opening of the oil container are only to be made by
the manufacturer or his service agent who should be contacted if there is an oil leak.
When scrapping the heater, follow the regulations concerning the disposal of oil.
Warning: Children should not use this appliance. Close supervision is necessary when any appliances are used near children.
Page 5
Page 6
SAFETY INSTRUCTIONS
Warning: Children of less than 3 years should be kept away unless continuously supervised.
Warning: Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Warning: Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
Warning: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to make sure that they do not play with or use the appliance.
Warning: In order to avoid overheating, do not cover the heater
Warning: This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to make sure that they do not play with or use the appliance.
Warning - Do not touch hot surfaces, do not block openings or
cover appliance.
Page 6
Page 7
FEATURE DIAGRAM
For Customer Services & Spare Parts please call 0345 209 7461
Or visit us at https://mda.russellhobbs.com
1. Handle
2. Fins
3. Castors/Wheels
4. Power/heat setting switches
5. Thermostat control
6. Thermostat indicator light
7. Power cable storage
Page 7
1
2
3
4 5
7
6
Page 8
BASE ASSEMBLY
For Customer Services & Spare Parts please call 0345 209 7461
Or visit us at https://mda.russellhobbs.com
Page 8
1. Attach the castors to the base plate and secure using the 4 x nuts supplied.
2. Then turn the heater upside down and position between the end fins.
3. Attach the base plates by hooking the 2 x U-bolts through the fins and securing with the 4 x wing nuts.
4. Once secure, turn the radiator round so that it is
sitting on the wheels.
Castor
Wing nut
Nut
U bolt
Rear of the appliance
U shaped base plate
Front of the
appliance
Flat base plate
Page 9
USING YOUR OIL FILLED RADIATOR
Page 9
1. Before connecting your appliance to the mains socket, position the appliance upright on the floor, at least 90cm away from the wall, away from curtains, furniture or wall coverings.
2. Insert the mains plug into a suitable 13 amp mains socket.
3. Turn the Power Control to the ‘I’, ‘II’ or ‘III’ position. The
appliance has 3 power settings.
Power Control Position RHOFR5001 RHOFR5002
OFF Power OFF Off Off I Low heat ON 600W 800W II Medium heat ON 900W 1.2kW III High heat ON 1.5kW 2.0kW
4. Turn the Thermostat Control to the desired position. It is
recommended to select the highest position to pre heat the appliance. It will take 5 -10 minutes for the appliance to fully heat up, the time taken for the heater to heat the room it is located in will be dependent on the size of the room and the ambient temperature of the room. The indicator light will illuminate when the unit is working, but the light will cycle on and off when the thermostat control
is set on a low setting and the heater is then maintaining
the room temperature.
Note: this appliance will not operate if the thermostat has been set too low.
Note: If the thermostat dial is set toward the maximum setting and the power control is set to off then the indicator light will
stay illuminated. No heat will be emitted as the power to the
heating elements is off.
Page 10
USING YOUR OIL FILLED RADIATOR
Page 10
Note: this appliance will not operate if is not placed on a stable surface.
5. When the room reaches the desired temperature, the radiator will cycle off and turn on again when the temperature drops.
6. If the room temperature falls below the desired temperature, the heating elements will turn on again until the room temperature reaches the desired temperature.
Note: this radiator is oil filled, and will cool down slowly after the power is shut off. Allow the radiator heater to cool prior to any movement, the built in carry handle should be used for easy movement.
Safety Protective Devices - The appliance is fitted with an over heat and tip over protection system.
1. Overheat protection - the power to the heating elements will automatically cut off if the temperature of the heating elements exceeds a certain limit. In the event of overheating, the heater will stop operating. Once the appliance has completely cooled the appliance will then resume operating as normal.
2. Tip Over Switch - The unit needs to be placed on a flat, firm and stable surface to ensure that the appliance contacts the floor firmly and internal tip over switch is level. If in the event that the unit tips over or is placed on an uneven or super very surface the appliance will not operate.
Page 11
USING YOUR OIL FILLED RADIATOR
Page 11
POWER CABLE STORAGE
When the appliance is not in use wrap the power cord around the storage hook to keep your appliance tidy and easy to store away.
The power cord must be completely unwrapped when plugged into the plug socket or in use.
Page 12
CLEANING AND CARE
Page 12
WARNING: Electrical Shock Hazard.
Before you clean the appliance, disconnect the mains plug from the wall socket.
Allow the appliance to cool down completely before cleaning.
Do not immerse cord, plug or appliance in any liquid or allow moisture to come into contact with electrical parts.
Clean the outer surface using a moist cloth and wipe over with a dry, soft cloth.
Do not use harsh detergents, abrasives or spray on cleaners.
Don’t allow water to seep into the openings or come into
contact with electrical connections.
Allow sufficient drying time before operating again.
Clean the air inlets and outlets regularly with a vacuum
cleaner using the brush attachment (with regular use, at least twice a year).
When the appliance is not in use. We recommend that, the heater is re-packed in its original packaging and stored in a
cool, dry place.
Page 13
PROBLEM SOLVING
Page 13
My appliance does not work when I turn it on:
1. Check that your appliance is plugged in and the power is turned on at the mains socket.
2. Try another mains socket.
3. Check the appliance is in an upright position.
4. Check that the thermostat setting has not been set too low.
5. Check if the Overheat protection has operated by leaving the appliance plugged un and giving it time to cool down. The heater should start to resume operating normally.
6. If the appliance still doesn’t work, do not try to repair it yourself.
If your appliance power is automatically cut off, follow the step below:
1. Unplug your appliance from the mains socket and allow it to completely cool down.
2. Inspect your appliance. Clean the air inlet and air outlet with a vacuum cleaner if necessary. If there are any signs of physical damage (e.g. melting, or burning of the case), do not attempt to use the appliance. Please leave all maintenance work to qualified personnel.
3. Plug in the appliance and switch it on again. If it cuts off again, move the appliance to a better ventilated location.
Page 14
At Russell Hobbs, we take all our customer feedback seriously.
Feel free to contact our Customer Service Team, on 0345 209 7461, who will be more than happy to assist you.
This product is guaranteed for 12 months from the date of the original purchase. If any defect arises due to faulty materials or workmanship, the faulty product must be returned to the place of purchase. Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with the original proof of
purchase.
• The product must be installed and used in accordance with the
instructions contained in this instruction guide and any other instructions for use which are supplied.
• It must be used for domestic purposes only and for its intended use.
• This warranty does not cover wear and tear, damage, misuse or
consumable parts.
This does not affect your statutory rights.
Imported by
G2S LIMITED WIGAN WN2 4AY
GUARANTEE AND CUSTOMER
SERVICES
Page 14
For Customer Services & Spare Parts please call 03452097461
Or visit us at https://mda.russellhobbs.com
Page 15
SPARE PARTS
Page 15
To check the availability of the following spare parts, simply contact our friendly Customer Services team using the details provided at the bottom of this page.
For Customer Services & Spare Parts please call 03452097461
Or visit us at https://mda.russellhobbs.com
Castors U-bolts
Base Plate
Page 16
CONNECTION TO THE MAINS
SUPPLY
Page 16
This appliance is designed to operate from a mains supply of 220-240V~50Hz/60Hz.
Check that the voltage marked on the product corresponds
with your supply voltage.
How to change the fuse
1. Slot the end of a screwdriver into the recess in the fuse holder of the plug.
2. Pull the fuse holder upwards until free of the plug and slide
the fuse out.
3. Replace the fuse and replace fuse holder, pushing down until locked into place.
Important: Only ever use a 13 amp fuse.
Page 17
SPECIFICATION
Page 17
Model number RHOFR5001 (B) Rated voltage 220V - 240V ~ 50Hz/60Hz Power consumption 1500W
Product dimensions (CMS) (H)62.5 x (W)24 x (D)33
Model number RHOFR5002 (B) Rated voltage 220V - 240V ~ 50Hz/ 60Hz Power consumption 2000W Product dimensions (CMS) (H)62.5 x (W)24 x (D)40.5
Model number
RHOFR5001 (B)
Item Symbol Value Unit Item Unit
Heat output
Type of heat input, for electric storage local space heaters only
Nominal heat output
P
nom 0.7311 kW
manual heat charge control, with integrated thermostat
NA
Minimum heatoutput (indicative)
P
min 0 kW
manual heat charge control with room and/or outdoor temperature feedback
NA
Maximum continuous heat output
P
max,c 0.7311 kW
electronic heat charge control with room and/or outdoor temperature feedback
NA
fan assisted heat output
NA
Auxiliary electricity consumption
Type of heat output/room temperature control
At nominal heat output
el
max N/A kW
single stage heat output and no room temperature control
No
At minimum heat output
el
min N/A kW
Two or more manual stages, no room temperature control
No
In standby mode
el
SB N/A kW
with mechanic thermostat room temperature control
Yes
with electronic room temperature control
No
electronic room temperature control plus day timer
No
electronic room temperature control plus week timer
No
Other control options (multiple selections possible)
room temperature control, with presence detection
No
room temperature control, with open windowdetection
No
with distance control option
No
with adaptive start control
No
with working time limitation
No
with black bulb sensor
No
Contact details
G2S LIMITED
WIGAN, WN2 4AY
Page 18
SPECIFICATION
Page 18
Model number
RHOFR5002 (B)
Item Symbol Value Unit Item Unit
Heat output
Type of heat input, for electric storage local space heaters only
Nominal heat output
P
nom 0.8731 kW
manual heat charge control, with integrated thermostat
NA
Minimum heatoutput (indicative)
P
min 0 kW
manual heat charge control with room and/or outdoor temperature feedback
NA
Maximum continuous heat output
P
max,c 0.8731 kW
electronic heat charge control with room and/or outdoor temperature feedback
NA
fan assisted heat output
NA
Auxiliary electricity consumption
Type of heat output/room temperature control
At nominal heat output
el
max N/A kW
single stage heat output and no room temperature control
No
At minimum heat output
el
min N/A kW
Two or more manual stages, no room temperature control
No
In standby mode
el
SB N/A kW
with mechanic thermostat room temperature control
Yes
with electronic room temperature control
No
electronic room temperature control plus day timer
No
electronic room temperature control plus week timer
No
Other control options (multiple selections possible)
room temperature control, with presence detection
No
room temperature control, with open windowdetection
No
with distance control option
No
with adaptive start control
No
with working time limitation
No
with black bulb sensor
No
Contact details
G2S LIMITED
WIGAN, WN2 4AY
Page 19
NOTES
Page 19
Page 20
Page 20
This symbol is known as the 'Crossed-out wheelie bin Symbol'. When
this symbol is marked on a product/batteries, it means that the
product/batteries should not be disposed of with your general
household waste. Only discard electrical/electronic/battery items in
separate collection schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to make sure the success of these schemes and for the protection of the environment. For
your nearest disposal facility, visit www.recycle-more.co.uk or ask in
store for details. We reserve the right due to possible changes to design
to alter the instruction manual without prior notice.
For Customer Services & Spare
Parts please call 03452097461
Or visit us at
https://mda.russellhobbs.com
Revision 1
Model number:
RHOFR5001 (B) RHOFR5002 (B)
Loading...