Russell Hobbs RH60GH403SS Instruction manual

Model number(s):

RH60GH403SS

Gas Hob

Instruction Manual

IMPORTANT:

RETAIN FOR FUTURE REFERENCE

For Customer Services & Spare Partsplease call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

Contents

Safety Instructions ………………………………………. 3-5

Product Overview ………………………………………. 6

Positioning ………………………………………. 7-8

Installation ………………………………………. 9-13

Usage ………………………………………. 14-18

Cleaning & Maintenance ………………………………………. 19-21

Trouble shooting ………………………………………. 22-24

Connection to the mains ………………………………………. 25

Guarantee ………………………………………. 26

Technical specification ………………………………………. 27

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

3

Safety Instructions

Important note:

Please read this booklet before installing and switching on this appliance.
The manufacturer assumes no responsibility for incorrect installation and
usage as described in this booklet.

This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance.

Gas appliances must be disconnected and installed by a Gas Safe
registered engineer. This scheme has replaced the Corgi registration
scheme. For details visit www.gassaferegister.co.uk or call 0800 408 5500.
Failure to do so will invalidate your guarantee, liability claims and could
lead to criminal prosecution

The use of a gas cooking appliance results in the production of heat,

moisture and products of combustion in the room in which it is installed.
Ensure that the kitchen is well ventilated especially when the appliance is
in use: keep natural ventilation holes open or install a mechanical
ventilation device (mechanical extractor hood).

In case of glass or steel hotplate breakage: shut immediately off all
burners and any electrical heating element and isolate the appliance from

the power supply. Do not touch the appliance surface and do not use the

appliance.

• Children should be supervised to ensure that they do not play with the
appliance.

• If the supply lead is damaged it must be replaced by a qualified person
using the correct lead, available from 0345 208 8750.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

4

Safety Instructions

• Packaging material is dangerous to children. Never allow children to play with
packaging material.

• Check the appliance for damage after unpacking it. Do not connect the
appliance if it has been damaged in transport.

• The appliance can only be used safely if it is correctly installed according to the

safety instructions. The installer is responsible for ensuring that the appliance
works correctly after installation.

• All operations relating to installation, regulation and conversion to other types
of gas must be carried out by an authorised installation engineer, respecting
applicable regulations, standards and the specifications of the local gas and
electricity providers.

• You are recommended to contact the Technical Assistance Service to convert to

another type of gas. Before installing your new hob, ensure that it is being

installed according to the assembly instructions.

• Prior to installation, ensure that the local distribution conditions (nature of the
gas and gas pressure) and the adjustment of the appliance are compatible.

• The adjustment conditions for this appliance are stated on the rating label.

• This appliance is not connected to a combustion products evacuation device. It

shall be installed and connected in accordance with current installation
regulations. Particular attention shall be given to the relevant requirements
regarding ventilation.

• This appliance can only be installed in a well-ventilated place in accordance with

existing regulations and ventilation specifications.

• The appliance must not be connected to a combustion product removal device.

• Do not subject the appliance to draughts. These might blow out the burners.

• This appliance leaves the factory set to the type of gas that is indicated on the

specifications plate. If this must be changed, read the assembly instructions.

• Do not tamper with the appliance's interior. If necessary, call our customer
helpline

• Do not switch on the appliance if it is damaged in any way. Contact our

customer helpline

• Caution: This appliance is only intended for cooking purposes. It is not to be
used for other purposes, for example not as a heating system or room heating

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

5

Safety Instructions

• Do not leave the appliance unattended during operation. The manufacturer is
not liable for damage which is caused by improper use or incorrect operation.

• Hot oil and fat can ignite very quickly. Never leave hot fat or oil unattended.
Never use water to put out burning oil or fat. Switch off the appliance.

Extinguish flames carefully using a lid, fire blanket or something similar.

• When gas burners are in operation without any cookware placed on them, they
can build up a lot of heat. Only operate the gas burners with cookware on them.

• Operating several gas burners at the same time gives rise to a great deal of
heat.

• The accessible parts become very hot when in operation. Never touch hot parts.
Keep children at a safe distance.

• Do not use covers. These can cause accidents, due to overheating, catching fire

or materials shattering, for example.

• Do not use inappropriate child safety shields or hob guards. These can cause
accidents.

• The hob will become very hot. Never place combustible items on the hob.
Never place objects on the hob.

• Incorrect repairs are dangerous. Repairs may only be carried out by a gas safe
registered engineer

• Components inside the appliance may have sharp edges. Wear protective
gloves.

• Do not use any high-pressure cleaners or steam cleaners, which can result in an

electric shock.

• Never use strong and abrasive cleaning agents as they will cause surface
damage.

• In the event of a malfunction, turn off the appliance’s gas and electricity supply.

For repairs, call customer services

• Warning: Do not use cooking vessel on the cooking zones that overlap its edges

• Warning: Do not use hob guards, inappropriate use of hob guards can cause

accidents.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

6

Product overview

1

2

3

5 6

1. Hob

2. Burners

A. Triple burner

B. Semi rapid burner
C. Rapid burner
D. Auxiliary burner

3. Dials

4. 3 x Pan support

5. 4 x Sponge

6. 4 x Bracket

7. 4 x Screws

8. 4 x Injector

9. Gas pipe bend

Unit & Spare Parts

If any of the above parts are missing please contact the customer service team on

0345 208 8750 or visit www.productcare.co.uk

7 8 9

C

4

A

D

B

Positioning

• This appliance is to be installed in a counter top.

• Avoid damaging the product during installation.

• The appliance can only be used safely if it is correctly installed according to the

safety instructions. The installer is responsible for ensuring that the appliance
works correct when installed.

• Gas appliances must be disconnected and installed by a Gas Safe registered
engineer. This scheme has replaced the Corgi registration scheme. For details
visit www.gassaferegister.co.uk or call 0800 408 5500. Failure to do so will
invalidate your guarantee, liability claims and could lead to criminal
prosecution.

• The edges of the hob must be a minimum of 60mm from a side or rear wall.

• The highest point of the hob (including the burners) must be a minimum of

700mm from the underside of any surface directly above it.

• The highest point of the hob (including the burners) must be a minimum of
400mm from the underside of any surface either side of the hob. If any surface
either side of the hob is lower than 400mm, then it must be at least 50mm
from the outer edges of the hob.

• There must be a minimum of 50mm of clearance around the hob and any
combustible materials.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

7

600mm

400mm

400mm

700mm

200mm

Positioning

• You must have a gap of a minimum gap of 25mm and a maximum gap of 74mm
between the underside of the appliance and any surface below it.

Note:

• Select heat-resistant work surface material to avoid larger deformation
caused by the heat radiation from the appliance.

• To install a hob above an oven, the oven must have forced ventilation.

• Check the dimensions of the oven when being installed with the hob

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

8

45mm

25mm (min.)

Installation

Preparation & installation

Ensure that there are no electric wires, gas or water pipes in the area where holes
are to be made.
Components of the appliance may have sharp edges. Wear protective gloves.

1. Ensure that that there is an electrical plug socket and gas supply within

adequate distance of the hob after it has been installed.

2. Cut out the aperture that measure 560mm by 490mm deep, in accordance

with the positioning instructions detailed on the previous page.

3. Remove the pan supports, burner lid, flame spreader and carefully turn the

appliance upside down and place it on a cushioned mat.

4. Apply the sponge provided around the edge of the appliance: the thickness of

the sponge is 1.5mm and width of it is 10mm.

5. Do not leave a gap in the sealing agent or overlap the thickness

6. Place the bracket over the holes in each corner of the hob that match the size

of the screws that have been provided.

7. Slightly tighten a screw through the bracket so that the bracket is attached to

the hob: you should still be able to adjust the position of the bracket.

8. Carefully turn the hob back over and gently lower it into the aperture hole that

you have cut out

9. On the underside of the hob, adjust the brackets into a position that is suitable

for your worktop.

10. Fully tighten the screws to secure the hob into position

Note: Do not use silicon sealant to seal the appliance against the aperture, as
this will make it difficult to remove the appliance in the future.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

9

Bracket

Screw

Sealing strip

Installation

Gas connection

• Gas appliances must be disconnected and installed by a Gas Safe registered
engineer. This scheme has replaced the Corgi registration scheme. For details
visit www.gassaferegister.co.uk or call 0800 408 5500. Failure to do so will
invalidate your guarantee, liability claims and could lead to criminal
prosecution.

• This appliance is supplied to run on LPG and natural gas, conversion to LPG or
natural gas must be undertaken by a Gas Safe registered engineer. This

scheme has replaced the Corgi registration scheme. For details visit

www.gassaferegister.co.uk or call 0800 408 5500. Failure to do so will
invalidate your guarantee, liability claims and could lead to criminal
prosecution

Gas supply replacement and installation guidelines

Electrical connection

• This appliance is designed to be connected to a 220-240V~50Hz AC electricity

supply.

• Before proceeding with the electrical connection, verify that the current
carrying capacity of the system and the isolator / main switch is adequate for
the maximum power rating of the hob.

• Electrical installation of the residence and of the appliance’s isolator must be

earthed and conform with the required safety regulations.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

10

Gas rail

Seal

G1/2” Female

coupler

Gas rail

Seal

Ø11.5 Female
coupler

Installation

• If there is no suitable circuit and a fused switch, they must be installed

by a qualified electrician before the hob is connected.

• Do not use adaptors, multiple sockets and/or extension leads.

• During installation, please ensure that insulated cables are used. An incorrect

connection might damage your appliance and will void the manufacturer’s

guarantee.

• All repairs must be carried out by an authorised service personal or a
qualified electrician.

• Switch off/isolate your appliance before each maintenance.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

11

Installation

Gas adjustment

Before any adjustment is started the gas and electricity supply to the appliance
must be turned off.

Change the injector of the burners

• Remove the pan support, burner cover and flame spreader

• Unscrew the injector using a spanner and replace it with the stipulated injector

for the new gas supply.

• Carefully reassemble all of the components.

• After the injectors are replaced, you must ensure the replacement injectors

are fully tightened.

Adjustment of the minimum flame level

• Turn the taps down to the minimum level

• Remove the dial from the tap and place a small bladed screw driver in the

centre of the tap shaft

• The correct adjustment is obtained when the flame has a length of 3mm - 4mm
(for butane/propane gas the adjustment screw must be tightly screwed in).

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

12

Injector

Installation

• Refit the dial and make sure that the flame does not go out by quickly turning

from maximum flame to minimum flame. If it does then remove the dial and

make further adjustments to the gas flow, testing it again once the adjustment
has been made.

• Repeat this process for each one of the dials/gas taps

Note:

• Do note dismantle the tap shaft, in the event of a malfunction change the
whole tap.

• Before placing the burners back, make sure that the injector is not blocked.

• A full operational test and leakage test must be carried out after a gas

conversion.

• After completing a conversion a qualified installer must mark a “V” on the

correct gas category to match with the setting in the rating label (remove the

previous “V” mark

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

13

Dial

Tap

Sealing ring

Adjustment screw

Usage

Note: The appliance is fitted with a flame failure safety device on each burner,
which is designed to stop the flow of gas to the burner head in the event of the
flame going out.

Dials

The appliance has 4 dials and these control the 4 burners, at the bottom left of

each dial there is an illustration that shows the burner that each dial controls:

Each dial has 4 icons, these are explained below:

To use a burner

1. Turn on the appliance at the plug.

2. Place a suitable pan on the pan support that is over the burner you wish to
use. Make sure the bottom of the pan and the surface of the pan support are
clean and dry.

3. Press the dial of the burner that you wish to light downwards and turn it anti­clockwise to the maximum setting (large flame).

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

14

Gas off

Ignition/spark

Maximum setting (large flame)

Minimum setting (small flame)

Burner indicator

Usage

3. You must keep the dial depressed so that the automatic ignition for the burner
operates.

4. You should hold down the control knob for 15 seconds after the flame has
ignited on the burner. If after 15 seconds the burner has not lit, stop operating
the device and wait at least 1 min before trying to ignite the burner again.

5. After this 15-second interval, you will be able to release the dial and set the
flame to your required level by turning the dial anti-clockwise.

6. The operating position MUST be at a position between the maximum and
minimum position.

7. To switch the burner off, turn the control dial clockwise to the gas off position.

Note: In case of power cut, the burners can be lit carefully by using a match.

Warnings:

• It is normal to hear a slight whistling noise while the burner is operating.

• When it is first used, it is normal for the burner to give off odours; this does

not pose any risk and does not indicate a malfunction; they will disappear in
time.

• A few seconds after the burner is switched off, a sound (thud) will be

produced. This is not a fault - this means that the safety device is no longer
operating.

• Keep the burner as clean as possible. If the ignition sparkers are dirty they

will not light properly. Clean them periodically using a small non-wire brush.
Bear in mind that the ignition sparkers must not suffer any serious impacts.

• An orange-coloured flame is normal. This is caused by the presence of dust in

the atmosphere, spilt liquids, etc.

• The kitchen will become hot and humid when this gas appliance is used. You

must therefore ensure that the kitchen is well ventilated: either keep the
natural ventilation apertures open, or install a ventilation system (extractor
hood).

• If using the appliance intensively for prolonged periods, you may require

additional ventilation (e.g. by opening a window) or more effective
ventilation (e.g. by increasing the hob's ventilation, if possible).

• If the burner flames are accidentally blown out, switch off the burner

operating control knob and do not try to relight it for at least one minute.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

15

Usage

Pans & energy saving

The following advice is to prevent damage to pans and help you save energy:

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

16

Burners

Suitable pan sizes (diameter)

Minimum diameter (mm) Maximum diameter (mm)

Triple 220mm 260mm
Rapid 200mm 240mm

Semi-rapid 160mm 180mm

Auxiliary 120mm 160mm

a

X

Always use pans that are the right
size for each burner to avoid

wasting gas and discolouring the

pans
Do not use small pans on large
burners, the flame should never
touch

the sides of the pans

Place a lid on pans

Do not

cook without a lid or with

the lid half off, as this wastes
energy

Only use pans with a thick, flat
bottom.

Do not use damaged

pans, which

do not sit evenly on the hob: pans
may tip over.

Always place pans

centrally over

the burners not to one side

Do not place pans on one side of a
burner, as it could tip over

Do not use large

pans on burners

near the controls, as they may be
damaged by the high
temperatures

Pans

must always be put on the
pan supports. Always ensure the
pan supports and burner covers
are correctly positioned before use

Never place pans directly on the
burners

Do not place anything between
pan and pan support

Be careful

when handling pans
when they are on the burner or
have just be taken away from the
burner

Do not use excessive weight or
strike the hob with heavy

objects

Usage

Cooking recommendations:

The following advice is to help you get the best cooking performance/results:

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

17

Burner Very high, High Medium Low

Triple or

Rapid

burner

Boiling, steaming, griddling,
toasting, paellas, Escalopes,

steaks, omelettes, frying,

Asian food (Wok cooking)

Reheating and keeping things hot:

cooked and pre-cooked dishes.

Rice, white sauce

and ragout.

Steaming: fish,

vegetables.

Semi-rapid

burner

Steamed potatoes, fresh

vegetables, stews, pasta, etc.

Reheating and keeping things hot:

pre-cooked dishes and delicate

casseroles.

Auxiliary

burner

Casseroles, rice pudding and

caramels.

Defrosting and

slow cooking:

vegetables, fruits

and frozen

products.

Melting: butter,

chocolate,

gelatine

Usage

Pan supports:

The pan supports will only align with the burners if they are put on the hob
correctly. The smallest pan support is for the middle 2 burners and can be placed
on the hob in any orientation.

The left and right pan supports are interchangeable, but you must ensure that the

thickest side of these pan supports are placed on the outside of the hob.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

18

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

19

Cleaning and Maintenance:

Important notes:

• The appliance will become hot during operation, allow the appliance to cool
down before cleaning.

• Do not use any high-pressure cleaners or steam cleaners.

• Wash new sponge cloths thoroughly before use.

• Follow all instructions and warnings included with the cleaning agents.

How to clean

Observe the information in the table below to ensure that the different surfaces
are not damaged by using the wrong type of cleaning agent. Do not use:

• Harsh or abrasive cleaning agents,

• Cleaning agents with a high concentration of alcohol,

• Hard scouring pads or sponges,

• High-pressure cleaners or steam cleaners.

Surface type How to clean

Stainless Steel Hot soapy water: Clean with a dish cloth and dry with a soft cloth.

Clean stainless steel surfaces in the direction of the grain only.

Special stainless steel cleaning products are available from
specialist retailers. Apply a very thin layer of the cleaning product
with a soft cloth.

Painted surfaces Hot soapy water: Clean using a damp dish cloth and dry with a

soft cloth/towel. Do not use any stainless steel cleaners.

Aluminium and plastic Glass cleaner: Clean with a soft cloth.

Glass Glass cleaner: Clean with a soft cloth. Do not use a glass scraper.

Cleaning and Maintenance:

How to clean:

• After each use, clean the surface of the respective burner parts once they have
cooled down. If any residue is left (baked-on food, drops of grease etc.),
however little, it will become stuck to the surface and more difficult to remove
later. The holes and grooves must be clean for the flame to ignite properly.

• The movement of some pans may leave metal residue on the pan supports.

• Clean the burners and pan supports using soapy water and scrub with a non-

wire brush.

• If the pan supports are fitted with rubber rests, ensure that these are also

cleaned. The rests may come loose and the pan support may scratch the hob.

• Always dry the burners and pan supports completely.

• Water droplets or damp patches on the hob at the start of cooking may

damage the enamel.

• After cleaning and drying the burners, make sure the burner covers are
correctly placed on the diffuser.

• Always clean off any liquid as soon as it is spilt: you will save yourself any
unnecessary effort.

• Do not leave acidic liquids (e.g. lemon juice, vinegar, etc.) on the hob.

• The ring cover of the double or triple flame burner and stainless steel parts

such as hotplate rings, top sheet and the area around the burners may become
discoloured over time. This is normal because of the high temperatures. Each
time the appliance is used these parts should be cleaned with a product that is
suitable for stainless steel.

CAUTION: The use of a gas cooking appliance results in the production of heat,

moisture and products of combustion" in the room in which it is installed. Ensure

that the kitchen. is well ventilated especially when the appliance is in use": keep
natural ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood).

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

20

Cleaning and Maintenance:

Cleaning the burners:

1. Remove the burner cover and spreader by pulling them upwards and away

from the hob.

2. Soak them in hot soapy water.

3. Clean them before drying them carefully, ensuring that the flame holes are

clean and completely dry.

4. Wipe the fixed parts of each burner with a damp cloth and dry them

afterwards.

5. Gently wipe the ignition device and a damp cloth and dry them carefully,

ensuring they are clean and completely dry.

6. Before placing the burners back on the hob you must ensure that the injector

is not blocked.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

21

Burner
cover

Flamer
spreader

Burner
cup

Ignition
sparkers

Flame failure

device

1. Place the flame spreader on to the
burner cup so that the ignition
device and the flame failure device
extend through their respective
holes in the flame spreader (the
flame spreader must click into place
correctly).

2. Position the burner cover onto the
flame spreader so that the retaining
pins fit into the their respective

recesses.

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

22

Trouble Shooting:

Problem Solution

Not ignited

The plug is not plugged in

Connect the appliance to the electricity supply

Power cut or faulty fuse

Check whether other kitchen appliances are working or
check in the fuse box to make sure that the fuse for the
appliance is working

The burner cover is badly assembled

Assemble the burner cover correctly

The gas supply is closed

Open the gas supply

Badly ignited

The burner cover is badly assembled

Assemble the burner cover correctly

The gas supply is closed

Open the gas supply

The burners are wet

Dry the burner cup, flame spreader and burner cover

The holes in the burner spreader are clogged or the
igniter is clogged

Clean the burner spreader and igniter

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

23

Trouble Shooting:

Problem Solution

Flame goes out

when in use

The flame failure device is clogged

Clean the flame failure device

Food that is being cooked has boiled over and
extinguished the flame

Turn off the burner, wait for 1 minute and reignite the
zone

The burner cover is badly assembled

Assemble the burner cover correctly

Flame has been blown out by a strong draught

Turn off the burner, check the cooking area for the
source of the draught (open window, etc.). Stop the
source of the draft, wait 1 minute and reignite the burner

Excessive noise

The burners make a noise during ignition and use

This is normal

The noise during operation is excessive

The burner cup, flame spreader or burner cover may be
badly assembled: Assemble correctly

Unstable flame

The burner cup, flame spreader or burner cover may be
badly assembled

Assemble correctly

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

24

Trouble Shooting:

Problem Solution

Yellow/orange

flame

The holes in the burner spreader are clogged or the

igniter is clogged

Clean the burner spreader and igniter

Orange flame

This is caused by the presence of dust in the atmosphere,
spilt liquids, etc.

A different type of gas is being used

Check gas supply

Gas smell

Gas leakage

Stop using the appliance, close the gas supply and open a
window or windows for ventilation

Vacate the area and contact customer services

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

25

WARNING- THIS APPLIANCE MUST BE EARTHED

This appliance is designed to operate from a mains supply of AC220 - 240V ~ 50HZ.
Check that the voltage marked on the product corresponds with your supply voltage.

For UK use only – Plug fitting details for rewireable plugs only (where applicable):
As the colours of the wires in the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:

The GREEN/YELLOW wire is the EARTH and must be connected to the terminal which
is marked with the letter E or by the earth symbol or coloured GREEN or
GREEN/YELLOW.

The BLUE wire is the NEUTRAL and must be connected to
the terminal marked with the letter N or coloured BLACK.

The BROWN wire is the LIVE wire and must be connected
to the terminal marked with the letter L or coloured RED.

Always ensure that the plug cord grip is fastened correctly.

If a 13A (BS1363) fused plug is used it must be fitted with a 13amp fuse conforming
to BS1362 and be BSI or ASTA approved.

Connection to the mains supply

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

26

Guarantee

This product is guaranteed for 12 months from the date of the

original purchase. If any defect arises due to faulty materials or

workmanship you must contact Product Care with the original proof
of purchase so a replacement or refund can be arranged.

Refund or replacement is at the discretion of Product Care.

The following conditions apply:

• Product Care will require a valid proof of purchase at the point of
replacement or refund.

• The product must be installed and used in accordance with the
instructions contained in this instruction guide and any other
instructions for use which has been supplied.

• It must be used for domestic purposes only and for its intended
use.

• This guarantee does not cover wear and tear, damage, misuse or
consumable parts.

This does not affect your statutory rights.

Imported by

G2S LIMITED
WIGAN
WN2 4AY

For Customer Services & Spare Parts please call 0345 208 8750

Opening times: Monday - Friday 8am – 8pm & Saturday 9am – 1pm

or visit us at www.productcare.co.uk

27

Technical Specification

Model number RH60GH403SS

Rated Voltage 220V – 240V ~ 50Hz

External Dimensions(HxWxD) 90mm x 600mm x 510mm

Burner Power (KW) Wok burner - 3.8 (277g/h)

Auxiliary burner - 1.0 (73g/h)
Rapid burner – 3.3 (241g/h)
Semi rapid burner – 2.0 (146g/h)

Gas hob class Class 3

Pin 2531CT-0116

Gas type &

Pressure

Electrical

power

Heat input and orifice size marked(mm)

Total

Wok

burner

Auxiliary

rapid

Rapid

Semi-rapid

220-240Vac

50Hz

3.8kW

(277g/h)

1.0kW

(73g/h)

3.3kW

(

241

g/h)

2.0kW

(

146

g/h)

10.1kW

(737g/h)

G30, 29mbar

0.99 0.50 0.90 0.70

G20, 20mbar

a

1.41 0.78 1.33 1.06

This symbol is known as the 'Crossed-out wheelie bin Symbol'. When this

symbol is marked on a product/batteries, it means that the product/batteries

should not be disposed of with your general household waste. Only discard
electrical/electronic/batteryitems in separate collection schemes, which cater
for the recovery and recycling of materials contained within. Your co-operation

is vital to make sure the success of these schemes and for the protection of the

environment. For your nearest disposal facility, visit www.recycle-more.co.uk

or ask in store for details.

We reserve the right due to possible changes to design to alter the

instruction manual without prior notice.

For Customer Services &

Spare Parts please call

0345 208 8750

Opening times:

Monday – Friday

8am – 8pm

&

Saturday

9am – 1pm

or visit us at

www.productcare.co.uk

Revision 1