Russell WE 17-12 Installation Manual

INSTALLATION OPERATION

AND MAINTENANCE INSTRUCTIONS

DIMENSIONS (IN)

MODEL

WE 17-12 WE 17-15

WE 17-18 WE 17-25 WE 17-35

WE 17-45

WE 18-55

12-3/4 12-3/4 15-3/4 18-3/4 21-3/4 24-3/4

24-3/4

13-5/8 13-5/8 13-5/8 14-5/8 15-5/8 15-5/8

15-5/8

15-13/16 15-13/16 15-13/16 16-13/16

17-7/8 20-1/2

20-1/2

D F

11-7/16 11-7/16

14-1/2 17-1/2 20-1/2 23-5/8

23-5/8

1-1/4 1-1/4 1-1/4 1-1/4 1-1/4 1-7/8

1-7/8

8-5/16 8-5/16 8-5/16 8-5/16

Wedge - Temp

IOM 115

9-1/2 9-5/8

9-5/8

15-1/4 15-1/4 17-3/4 19-7/8 22-7/8 26-3/4

26-3/4

Liquid Conn.

1/2 FN 1/2 FN 1/2 FN 1/2 FN

1/2 FN 1/2 FN

1/2 FN

Suction

Conn.

1/2 OD 1/2 OD 1/2 OD 1/2 OD

1/2 OD 1/2 OD 1/2 OD

(lbs.)

eight

16 19 22 29

36 57 65

GENERAL

RECEIPT AND EXAMINATION

Carefully check all items against bill of lading to be sure everything has been received as ordered. Carefully inspect all items for damage and, if any is found, report it immediately to the carrier and file damage claim with same.

INSTALLATION

LOCATION AND MOUNTING

The WE is designed to mount on ceiling only. The unit should be installed so that there are no restrictions on the air inlet or outlet as this will cause the refrigeration system to operate less ef

Remove the unit from the carton. Using the fastener holes in the unit as a guide, locate the mounting fasteners in the ceiling of the walk-in or reach-in cooler. Use #10 screws or 1/4” diameter bolts to secure the unit to the ceiling. This unit must be installed so as to allow drainage of condensate coming off the coil.

The National Sanitation Foundation (NSF) requires that any flush mounted unit be properly and completely sealed, with an approved NSF sealant, between the unit and the mounting surface.

ELECTRICAL

System electrical installation should conform to all applicable codes and practices. according to the nameplate motor circuit electrical ratings.

REPLACEMENT PARTS

o order replacement parts, contact your local representative or contact the factory (800) 288-9488 for the location of the nearest HTP

T Always provide the evaporator model number, serial number, unit voltage and a complete description of the part required.

Coil

Model

Number

WE 17-12 WE 17-15 WE 17-18 WE 17-25 WE 17-35 WE 17-45 WE 18-55

MOT

FAN MOTOR

4 Watt 9 Watt 9 Watt 9 Watt

16 Watt

1/20 1/20

MOT

RPM

1550 1550 1550 1550 1550 1550 1550

ficiently.

NUMBER

102104002 103104004 103104004 103104004 103104007 102540001 102540001

All models will require the connection of power to the fan motor

wholesaler

BLADE

BORE DESCRIPTION

1/4” 1/4” 1/4”

Hubless

1/4” 5/16 5/16

831 CCW 831 CCW

831 CCW 1020 CCW 1031 CCW 1219 CCW 1219 CCW

NUMBER

204395010 204395010 204395010 204395016 204395018

11860 11860

FAN GUARD

DIA.

8” 8” 8”

8” 10” 12” 12”

PAR T

NUMBER

206569000 206569000 206569000 201006002 201006002 201006003 201006003

DRAIN PAN

Part No. #08499044

PAR T

NUMBER 20193200

20193200 20193000 20192600 20192400 20194000 20194000