Wizard
User Manual
Professional Entertainment Technology
© 2013-14 Martin Professional ApS. Information subject to change without notice. Martin
Professional and all affiliated companies disclaim liability for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss occasioned by the use of,
inability to use or reliance on the information contained in this manual. The Martin logo, the
RUSH by Martin logo, the RUSH by Martin name, the Martin name and all other trademarks in
this document pertaining to services or products by Martin Professional or its affiliates and
subsidiaries are trademarks owned or licensed by Martin Professional or its affiliates or
subsidiaries.
Manual: Revision C
Table of contents
Safety information ............................................................................................. 4
Lamp safety ................................................................................................... 7
Introduction ..................................................................................................... 10
Before using the product for the first time ................................................... 10
Physical installation ........................................................................................ 11
Fastening the fixture to a flat surface .......................................................... 11
Mounting the fixture on a truss .................................................................... 12
Securing with a safety cable ....................................................................... 13
AC power ........................................................................................................ 14
Fixture overview .............................................................................................. 16
Control data link .............................................................................................. 18
Connecting the DMX data link ..................................................................... 18
Fixture setup ................................................................................................... 20
Focus ........................................................................................................... 20
Using the control menus ............................................................................. 20
DMX function settings ................................................................................. 20
Standalone operation .................................................................................. 21
Master/slave operation ................................................................................ 21
DMX state .................................................................................................... 23
Fixture settings ............................................................................................ 24
Fixture test ................................................................................................... 24
Lamp settings .............................................................................................. 24
Fixture information....................................................................................... 25
Reset fixture ................................................................................................ 27
Effects ............................................................................................................. 28
Dimming ...................................................................................................... 28
Shutter ......................................................................................................... 28
Color/animation wheel ................................................................................. 28
Reflector, pan and tilt .................................................................................. 28
Gobo wheel ................................................................................................. 28
Effect movement ......................................................................................... 29
Pre-programmed effects and sound activation ........................................... 30
Fixture settings control via DMX ................................................................. 30
Maintenance ................................................................................................... 31
Cleaning ...................................................................................................... 31
Replacing the primary fuse ......................................................................... 35
DMX protocol .................................................................................................. 36
Control menus ................................................................................................. 41
Troubleshooting .............................................................................................. 43
Specifications .................................................................................................. 45
4 RUSH Wizard User Manual
Safety information
WARNING!
Read the safety precautions in this manual before installing,
operating or servicing this product.
The following symbols are used to identify important safety information on the
product and in this manual:
Warning!
Safety hazard.
Risk of severe
injury or
death.
Warning!
Powerful light
emission. Risk
of eye injury.
Warning!
See user
manual for
important
safety
information.
Warning!
Hazardous
voltage. Risk
of lethal or
severe electric
shock.
Warning!
Hot surfaces
and fire
hazard.
Warning! Risk Group 1 product according to EN 62471. Avoid
staring directly into the beam. Do not view the light output with
optical instruments or any device that may concentrate the
beam.
This lighting fixture is for professional use only – it is not for
household use. The fixture must be installed by a qualified
technician. The safety of the installation is the responsibility of
the installer. The fixture presents risks of severe injury or death
due to fire hazards, electric shock and falls if the safety
precautions below are not followed.
If you have any questions about how to install, operate or
service the fixture safely, please contact your Martin™
distributor (see www.martin.com/distributors for details) or call
the Martin™ 24-hour service hotline on +45 8740 0000, or in the
USA on 1-888-tech-180.
Respect all locally applicable laws, codes and regulations when
installing, operating or servicing the fixture.
RUSH Wizard User Manual 5
Refer any service operation not described in this manual to an
authorized Martin™ service technician. Do not try to carry out
any such operation yourself, as doing so may present a health
or safety risk. It may also cause damage or malfunction and it
may void your product warranty.
Install, operate and service RUSH by Martin™ products only as
directed in their user manuals, or you may create a safety
hazard or cause damage that is not covered by product
warranties.
Follow the safety precautions listed below and observe all
warnings in this manual and printed on the product. Keep this
manual for future use.
For the latest user documentation and other information about
this and all Martin™ products, please visit the Martin website at
http://www.martin.com
Protection from electric shock
Do not expose the fixture to rain or moisture.
Disconnect the fixture from AC power before carrying out any
installation or maintenance work, such as changing the lamp,
and when the fixture is not in use.
Ensure that the fixture is electrically connected to ground
(earth).
Use only a source of AC power that complies with local building
and electrical codes and has both overload and ground-fault
(earth-fault) protection.
Socket outlets or external power switches used to supply the
fixture with power must be located near the fixture and easily
accessible so that the fixture can easily be disconnected from
power.
Replace defective fuses with ones of the specified type and
rating only.
Isolate the fixture from power immediately if the power plug or
any seal, cover, cable, or other component is damaged,
defective, deformed, wet or showing signs of overheating. Do
not reapply power until repairs have been completed.
6 RUSH Wizard User Manual
Before using the fixture, check that all power distribution
equipment and cables are in perfect condition and rated for the
current requirements of all connected devices.
Use only Neutrik PowerCon cable connectors to connect to the
fixture’s power sockets.
Do not connect devices to power in a chain that will exceed the
electrical ratings of any cable or connector used in the chain.
The supplied power input cable is rated 6 A and can safely
supply only one fixture with mains power. Do not connect any
device to the fixture’s MAINS OUT connector when using this
cable. If you replace this cable and also use the replacement
cable to supply only one fixture with mains power, the
replacement cable must also be rated 6 A minimum, have three
conductors 18 AWG or 0.75 mm² minimum conductor size, have
an outer cable diameter of 6 - 15 mm (0.2 - 0.6 in.) and be
temperature-rated to suit the application. In the USA and
Canada the cable must be UL listed, type SJT or equivalent. In
the EU the cable must be type H05VV-F or equivalent.
To connect fixtures to mains power in a chain, you must first
obtain 14 AWG or 1.5 mm
2
power input and throughput cables
that are 16 A rated and temperature-rated to suit the
application. In the USA and Canada the cables must be ULlisted, type SJT or equivalent. In the EU the cables must be
type H05VV-F or equivalent. Suitable cables with Neutrik
PowerCon connectors are available from Martin™ (see
‘Accessories’ on page 47). If you use these cables, you can
connect fixtures to power in a linked chain, MAINS OUT
throughput socket to MAINS IN input socket, but do not link
more than:
• six (6) RUSH Wizard fixtures in total at 100-120 V, or
• twelve (12) RUSH Wizard fixtures in total at 200-240 V.
The voltage and frequency at the MAINS OUT socket are the
same as the voltage and frequency applied to the MAINS IN
socket. Only connect devices to the MAINS OUT socket that
accept this voltage and frequency.
Protection from burns and fire
Do not operate the fixture if the ambient temperature (T
a
)
exceeds 40° C (104° F).
RUSH Wizard User Manual 7
The surface of the product casing can reach up to 75° C
(167° F) during operation. Avoid contact by persons and
materials. Allow the fixture to cool for at least 30 minutes before
handling.
Keep flammable materials well away from the fixture. Keep all
combustible materials (e.g. fabric, wood, paper) at least 100
mm (4 in.) away from the fixture.
Ensure that there is free and unobstructed airflow around the
fixture. Provide a minimum clearance of 100 mm (4 in.) around
fans and air vents.
Do not illuminate surfaces within 200 mm (7.9 ins.) of the
fixture.
Do not attempt to bypass thermostatic switches or fuses.
Do not stick filters, masks or other materials onto any optical
component.
Lamp safety
Install only a lamp that is approved for use in the product.
Prolonged exposure to an unshielded discharge lamp can cause
eye and skin burns. Do not stare directly into the light output.
Do not look at an exposed lamp while it is lit.
Do not operate the fixture with missing or damaged covers,
shields, lenses, ultraviolet screens or any optical component.
A hot discharge lamp is under pressure and can explode without
warning. Allow the fixture to cool for at least 30 minutes and
protect yourself with safety glasses and gloves before handling a
lamp.
Replace the lamp immediately if it becomes visually deformed,
damaged or in any way defective.
Monitor hours of lamp use and lamp intensity and replace the
lamp when it reaches the limit of its service life as specified in
this manual or by the lamp manufacturer.
If the quartz envelope of a discharge lamp is broken, the lamp
releases a small quantity of mercury and other toxic gases. If a
discharge lamp explodes in a confined area, evacuate the area
and ventilate it thoroughly. Wear nitrite gloves when handling a
8 RUSH Wizard User Manual
broken discharge lamp. Treat broken or used discharge lamps
as hazardous waste and send to a specialist for disposal.
Protection from eye injury
The fixture emits infrared and ultraviolet rays that are not
normally visible but that may be harmful to the eyes and skin.
Do not stare at an operating lamp. Minimize exposure to eyes
or skin. Use appropriate shielding or eye protection.
Do not stare directly into the light output.
Ensure that persons are not looking directly into the light output
when the product lights up suddenly. This can happen when
power is applied, when the product receives a DMX signal, or
when certain control menu items are selected.
Do not look at the light output with magnifiers, telescopes,
binoculars or similar optical instruments that may concentrate
the light output.
To minimize the risk of eye irritation or injury, disconnect the
fixture from power at all times when the fixture is not in use, and
provide well-lit conditions to reduce the pupil diameter of
anyone working on or near the fixture.
Do not operate the fixture with missing or damaged covers,
shields or any optical component. If shields, lenses or ultraviolet
screens have become visibly damaged to such an extent that
their effectiveness is impaired, for example by cracks or deep
scratches, return the fixture to an authorized Martin™ service
agent for replacement.
Protection from injury
Fasten the fixture securely to a fixed surface or structure when
in use. The fixture is not portable when installed.
Ensure that any supporting structure and hardware used can
hold at least 10 times the weight of all the devices they support.
If suspending from a rigging structure, fasten the fixture to a
rigging clamp. Do not use safety cables as the primary means
of support.
If the fixture is installed in a location where it may cause injury
or damage if it falls, install as directed in this manual a
secondary attachment such as a safety cable that will hold the
fixture if a primary attachment fails. The secondary attachment
RUSH Wizard User Manual 9
must be approved by an official body such as TÜV as a safety
attachment for the weight that it secures, must comply with EN
60598-2-17 Section 17.6.6 and must be capable of bearing a
static suspended load that is ten times the weight of the fixture
and all installed accessories.
Check that all external covers and rigging hardware are
securely fastened.
Block access below the work area and work from a stable
platform whenever installing, servicing or moving the fixture.
In the event of an operating problem, stop using the fixture
immediately and disconnect it from power. Do not attempt to
use a fixture that is obviously damaged.
Do not modify the fixture or install other than genuine RUSH by
Martin™ parts.
Refer any service operation not described in this manual to a
qualified technician.
10 RUSH Wizard User Manual
Introduction
The RUSH Wizard™ is a multi-beam effect light that creates intense longthrow narrow beams with multi-color and gobo pattern projections and
features electronic dimming and a strobe effect. The Wizard features a show
mode with preprogrammed macros that allow fast deployment of a full range
of effects. It offers both DMX control and standalone operation with music trig
and master/slave options.
The fixture is supplied with a discharge lamp (installed), a 1.5 m (5 ft.) power
cable (local power plug not included) and a folding bracket to allow fastening
to a surface or rigging clamp.
Before using the product for the first time
1. Read ‘Safety information’ on page 4 before installing, powering, operating
or servicing the fixture.
2. Unpack and ensure that there is no transportation damage before using
the fixture. Never attempt to operate a damaged fixture.
3. If the fixture is not going to be hard-wired to a mains supply, attach a local
power plug (not supplied) to the end of the supplied power cable.
4. Before operating, ensure that the voltage and frequency of the power
supply match the power requirements of the fixture.
5. Check the RUSH support pages on the Martin Professional website at
www.martin.com for the most recent user documentation and technical
information for the fixture. RUSH by Martin™ user manual revisions are
identified by the revision letter at the bottom of the inside cover.
Note that whenever AC mains power is applied to the fixture, it will reset all
effects and functions to their home positions. This process usually takes
around 20 seconds.
RUSH Wizard User Manual 11
Physical installation
Read ‘Safety information’ on page 4 before installing the
fixture.
The fixture is designed for indoor use only and must be used in
a dry location with adequate ventilation. Ensure that none of the
fixture’s ventilation slots are blocked.
Fasten the fixture to a secure structure or surface. Do not stand
it on a surface or leave it where it can be moved or fall over. If
you install the fixture in a location where it may cause injury or
damage if it falls, secure it as directed in this user manual using
a securely anchored safety cable that will hold the fixture if the
primary fastening method fails.
Martin™ can supply safety cables and rigging clamps that are suitable for use
with the fixture (see ‘Accessories’ on page 47).
Fastening the fixture to a flat
surface
To mount the fixture on a wall or
other vertical surface:
1. Check that the surface can
support at least 10 times the
weight of all fixtures and
equipment to be installed on it.
2. Obtain two 8 mm diameter hex
bolts or screwbolts with max. 13
mm head size and install them
90 mm (3.5 in.) apart (center to
center), in the mounting surface.
3. Install an eyebolt securely in the mounting surface to use as an anchoring
point for the fixture’s safety cable.
4. Fold the fixture’s mounting bracket so that it lies flat against the back of
the fixture and lock it in position by tightening the clamping handles. Lift
the clamping handles away from the bracket slightly until they turn freely,
then turn them so that they lie flat against the fixture and will not get in the
way when you hang the fixture on the mounting surface. Alternatively, you
12 RUSH Wizard User Manual
can use a screwdriver to tighten the screws in the center of the clamping
handles after you have hung the fixture on the mounting surface.
5. Hang the fixture on the wall over the two bolt or screwbolt heads using the
two slotted holes in the mounting bracket so that the fixture is held
securely and cannot fall off the bolts.
6. Install a safety cable as directed in ‘Securing with a safety cable’ on page
13.
Mounting the fixture on a truss
The fixture can be clamped to a truss or similar rigging
structure in any orientation using one or more closed-type
rigging clamps such as half-coupler clamps (see illustration
on right) that completely enclose the truss chord.
To mount the fixture on a truss:
1. Check that the truss can support at least 10 times the
weight of all fixtures and equipment to be installed on it.
2. Block access below the work area.
3. Check that the rigging clamp is undamaged and approved for the fixture’s
weight. Bolt the rigging clamp securely to the fixture’s mounting bracket
with a grade 8.8 minimum steel M12 bolt and self-locking nut (or as
recommended by the clamp manufacturer) fastened through one of the
clamp holes in the fixture’s folding bracket. You can use any of the holes
RUSH Wizard User Manual 13
in the mounting bracket for attachment, but ensure that the load will be
distributed evenly.
4. See illustration below. Working from a stable platform, fasten the clamp
securely around the truss chord or similar bar.
5. Install a safety cable as directed in ’Securing with a safety cable’ below.
6. Loosen the swivel locks, tilt the fixture to the desired angle, and retighten.
Securing with a safety cable
Secure the fixture with a safety cable (or other secondary attachment) that is
approved for the weight of the fixture so that the safety cable will hold the
fixture if the primary attachment fails.
See illustration above. Attach the safety cable to the attachment point
(arrowed) on the fixture and to a secure anchoring point (securely anchored
eyebolt or truss chord, for example).
14 RUSH Wizard User Manual
AC power
Read ‘Safety information’ on page 4 before connecting the
fixture to AC mains power.
Warning! The mains power input cable supplied with the
fixture is rated 6 A and can supply only one fixture with
mains power. Do not connect any device to the fixture’s
MAINS OUT power throughput socket when using this
input cable. If you want to connect other fixtures to the
MAINS OUT socket, see ‘Linking fixtures to power in a
chain’ on page 15.
For protection from electric shock, the fixture must be grounded
(earthed). The power distribution circuit must be equipped with
a fuse or circuit breaker and ground-fault (earth-fault)
protection.
Socket outlets or external power switches used to supply the
fixture with power must be located near the fixture and easily
accessible so that the fixtures can easily be disconnected from
power.
Do not insert or remove live Neutrik PowerCon connectors to apply or cut
power, as this may cause arcing at the terminals that will damage the
connectors.
Do not use an external dimming system to supply power to the fixture, as this
may cause damage to the fixture that is not covered by the product warranty.
The fixture can be hard-wired to a building electrical installation if you want to
install it permanently, or a power plug (not supplied) that is suitable for the
local power outlets can be installed on the power cable.
If you install a power plug on the power cable, follow the plug manufacturer’s
instructions and connect the wires in the power cable as shown in this table:
Earth, Ground or
Neutral or N Live or L
US system
Green White Black
EU system
Yellow/green Blue Brown
The fixture has an auto-ranging power supply that accepts AC mains power at
100-240 V at 50/60 Hz. Do not apply AC mains power at any other voltage or
frequency to the fixture.
RUSH Wizard User Manual 15
Linking fixtures to power in a chain
If you obtain a 14 AWG / 1.5 mm2 power input cable and 14 AWG / 1.5 mm2
throughput cables from Martin™ (see ‘Accessories’ on page 47), you can
relay mains power from one fixture to another by connecting fixtures to power
in a linked daisy-chain, MAINS OUT throughput socket to MAINS IN input
socket.
Using 14 AWG or 1.5 mm
2
cables from Martin™, you can link:
• Maximum six (6) RUSH Wizard fixtures to power in a chain at 100-120 V,
or
• Maximum twelve (12) RUSH Wizard fixtures to power in a chain at 200-
240 V.
16 RUSH Wizard User Manual
Fixture overview
1 - Display
2 – Status LEDs
The fixture has four LEDs on the rear of the fixture:
DMX On DMX input present
MASTER On Master mode
SLAVE On Slave mode
SOUND Flashing Sound activation (music trig)
3 - Buttons
MENU
• Activate the menu mode functions, or
• Return to the previous level of the menu
structure, or
• Press and hold to exit menus completely
DOWN Go down a menu branch
UP Go up a menu branch
ENTER Confirm the selected function
RUSH Wizard User Manual 17
4 - DMX XLR input/output sockets
5-pin XLR sockets are provided for DMX input and output (throughput).
5 – AC mains power input
A blue Neutrik PowerCon socket is provided to connect the fixture to mains
power.
6 - Mains power throughput
The white Neutrik PowerCon socket can be used to supply power to other
fixtures only if safety limits (see ‘Safety information’ on page 4) are respected.
7 - Microphone
Built-in microphone for sound-activated scene changes (music trig) in show
mode.
8 - Fuse
The T 6.3A fixture fuse F1 is located in a fuseholder next to the AC mains
power connectors.
9 - Safety cable attachment point
Loop a secondary attachment such as an approved safety cable that is rated
for the weight of the fixture through this attachment.
18 RUSH Wizard User Manual
Control data link
A DMX 512 data link is required in order to control the fixture via DMX. The
fixture has 5-pin XLR connectors for DMX data input and output.
The number of daisy-chained fixtures is limited by the number of DMX
channels required by the fixtures in relation to the maximum 512 channels
available in one DMX universe. Note that if independent control of a fixture is
required, it must have its own DMX channels. Fixtures that are required to
behave identically can share the same DMX address and channels. To add
more fixtures or groups of fixtures when the above limit is reached, add a
DMX universe and another daisy-chained link.
Tips for reliable data transmission
Use shielded twisted-pair cable designed for RS-485 devices: standard
microphone cable cannot transmit control data reliably over long runs. 24
AWG cable is suitable for runs up to 300 meters (1000 ft.). Heavier gauge
cable and/or an amplifier is recommended for longer runs. The pin-out on all
connectors is pin 1 = shield, pin 2 = cold (-), and pin 3 = hot (+). Pins 4 and 5
in the 5-pin XLR connectors are not used in the fixture but are available for
possible additional data signals as required by the DMX512-A standard.
Standard pin-out is pin 4 = data 2 cold (-) and pin 5 = data 2 hot (+).
To split the link into branches, use a splitter such as the Martin 4-Channel
Opto-Isolated RS-485 Splitter/Amplifier. Terminate the link by installing a DMX
termination plug in the output socket of the last fixture. The termination plug,
which is a male XLR plug with a 120 Ohm, 0.25 W resistor soldered between
pins 2 and 3, “soaks up” the control signal so it does not reflect and cause
interference. If a splitter is used, terminate each branch of the link.
Connecting the DMX data link
To connect the fixture to data:
1. Connect the DMX data output from the controller to the first fixture’s male
XLR DMX input connector.
RUSH Wizard User Manual 19
2. Connect the first fixture’s DMX output to the DMX input of the next fixture
and continue connecting fixtures output to input. Terminate the last fixture
on the link with a DMX termination plug.
20 RUSH Wizard User Manual
Fixture setup
This section explains manual focus adjustment and the fixture settings and
utilities that the user has access to via the control panel.
Settings are retained when the fixture is powered off.
For a complete map of the control menu
structure, see ‘Control menus’ on page 23.
Focus
See illustration on right. You can adjust the
sharpness of the fixture’s projections by
turning the focus knob (arrowed).
Using the control menus
To access the control menus, press the MENU
button. Navigate the menu structure using the
ENTER, DOWN and UP buttons. Select any required menu option using the
ENTER button. To return to the previous level in the menu structure without
making a change, press the MENU button.
To exit the menus, press and hold the MENU button.
DMX function settings
DMX function settings include the DMX address and a DMX value viewer.
DMX addressing
The fixture can be controlled using signals sent by a DMX controller. The
DMX address, also known as the start channel, is the first channel used to
receive instructions from a DMX controller. Each DMX-controlled fixture must
have a DMX address set. If a fixture has its DMX address set to 1, for
example, then it uses channels 1 to 10. The next fixture on the DMX link can
have its DMX address set to 11, the next to 21 and so on until the 512
channels in one DMX universe are allocated.
For independent control, each fixture must be assigned its own control
channels. Two fixtures of the same type may share the same address, if
identical behavior is desired. Address sharing can be useful for diagnostic
purposes and symmetric control, particularly when combined with the inverse
pan and tilt options.
RUSH Wizard User Manual 21
To set the fixture’s DMX address:
1. In the control panel, select DMX ADDRESS
and press ENTER.
2. Use the UP and DOWN buttons to select DMX ADDRESS and press
ENTER to confirm. The present address will blink on the display.
3. Use the UP and DOWN buttons to select a new address.
4. Once the address has been selected, press ENTER to set it (or press
MENU to exit without making a change).
Standalone operation
The fixture can run a standalone light show without needing a DMX signal. 6
different pre-programmed standalone shows are available. Shows can be
triggered automatically or by a music beat.
Show mode
To select which pre-programmed show a fixture runs in standalone mode:
1. Select SHOW MODE and press ENTER to confirm.
2. Use the DOWN and UP buttons to select SHOW 0 (random show) or
SHOW 1 to SHOW 6 (pre-programmed shows).
3. Press ENTER to set (or press MENU to exit without making a change).
Master/slave operation
Fixtures in standalone mode can be linked in a chain and set to master/slave
operation, where one master fixture running a standalone show controls
synchronized scene changes in slave fixtures.
You must set all the fixtures except one as slaves. If you allow more than one
fixture in a chain to act as master, you may cause damage that is not covered
by the product warranty.
To run fixtures in master/slave operation:
1. Link fixtures in a chain, using DMX cable to connect one fixture’s DMX
OUT socket to the next fixture’s DMX IN socket.
2. Set all fixtures to enter Master/Slave mode when they are not receiving a
DMX signal in the DMX STATE menu (see ‘Master/slave’ on page 23).
3. Set the first fixture in the chain to run a standalone show using its SHOW
MODE menu (see ‘Show mode’ above). This fixture will now act as the
master.
22 RUSH Wizard User Manual
4. On each of the other fixtures in the chain, select SLAVE MODE and press
ENTER. Use the UP and DOWN buttons to select SLAVE 1 (fixture runs
the same show as the master) or SLAVE 2 (fixture runs a show that is
synchronized with the master but has slight variations). Then press
ENTER to set (or press MENU to exit without making a change).
5. Make sure that the fixtures are not receiving a DMX signal.
When fixtures are correctly connected and set up in master/slave operation,
the Master status LED on the master fixture and the Slave status LED on
slave fixtures light constantly.
Split colors
The fixture can be set so that the color wheel shows split and full colors or
shows full colors only. To alter the split color setting:
1. Select SPLIT COLOR
and press ENTER.
2. Use the UP and DOWN buttons to select YES or NO and press ENTER to
confirm. The currently active mode will blink on the display.
3. Use the UP and DOWN buttons to select YES (split colors allowed) or NO
(full colors only).
4. Press ENTER to set (or press MENU to exit without making a change).
Sound activation (music trig)
The fixture’s built-in sound activation microphone can be used to trigger scene
changes with a music beat when the fixture is running a standalone show.
When sound activation is running, the Sound status LED on the control panel
flashes in synch with the music beat.
To set music trig sound activation:
1. Select SOUND MODE
and press ENTER to confirm.
2. Use the DOWN and UP buttons to select ON (sound activation enabled)
or
OFF (sound activation disabled).
3. Press ENTER to set (or press MENU to exit without making a change).
Sound activation microphone sensitivity
To adjust the sensitivity of the sound activation microphone:
1. Select SOUND SENSE and press ENTER to confirm.
RUSH Wizard User Manual 23
2. Use the DOWN and UP buttons to change the microphone sensitivity
level from 0…100.
3. Press ENTER to set the level (or press MENU to exit without making a
change).
DMX state
The DMX state menu lets you set the fixture’s behavior when it is powered on
but is not receiving a DMX signal. You can set the fixture to:
• enter master/slave standalone operation
• blackout, or
• return to its last state.
Master/slave
To set the fixture to enter standalone operation and apply the master/slave
settings described at the beginning of this section (see page 21).
1. Select DMX STATE and press ENTER to confirm.
2. Use the DOWN and UP buttons to select MASTER/SLAVE and press
ENTER to confirm.
3. Use the DOWN and UP buttons to select ON or OFF.
4. Press ENTER to confirm (or press MENU to exit without making a
change).
Blackout
To set the fixture to black out:
1. Select DMX STATE and press ENTER to confirm.
2. Use the DOWN and UP buttons to select BLACKOUT.
3. Press ENTER to confirm (or press MENU to exit without making a
change).
Last state
To set the fixture to return to the last state it was in when was is not receiving
a DMX signal:
1. Select DMX STATE and press ENTER to confirm.
2. Use the DOWN and UP buttons to select LAST STATE.
24 RUSH Wizard User Manual
3. Press ENTER to confirm (or press MENU to exit without making a
change).
Automatically turn off display backlight
By default the display is lit when power is applied to the fixture. It can be set to
automatically dim when the control panel has not been used for a period:
1. Select BACK LIGHT and press ENTER to confirm.
2. Use the DOWN and UP buttons to select OFF (display goes into sleep
mode) or ON (display remains lit constantly)
3. Press ENTER to confirm (or press MENU to exit without making a
change).
Fixture settings
Pan Reverse
To adjust the pan settings:
1. Select PAN REVERSE and press ENTER to confirm.
2. Use the DOWN and UP buttons to select YES (pan inversion) or NO (pan
normal).
3. Press ENTER to confirm (or press MENU to exit without making a
change).
Fixture test
Automatic tests of all functions can be run from the control menus.
Auto test
To perform a complete test of all of the fixture functions:
1. Select AUTO TEST and press ENTER to confirm. The fixture will run the
auto test routine.
2. Press MENU to stop the test and exit.
Lamp settings
Lamp On/Off
To manually power the lamp on or off:
1. Select LAMP ON/OFF and press ENTER to confirm.
RUSH Wizard User Manual 25
2. Use the DOWN and UP buttons to select ON or OFF.
3. Press ENTER to confirm and power the lamp on or off (or press MENU to
exit).
Lamp Power On
To set the lamp to power on automatically when the fixture is powered on:
1. Select LAMP POWER ON and press ENTER to confirm.
2. Use the DOWN and UP buttons to select ON or OFF.
3. Press ENTER to confirm (or press MENU to exit without making a
change).
DMX lamp control
The lamp can be controlled remotely by DMX. The following options are
available:
• LAMP OFF VIA DMX allows the lamp to be powered off by sending a DMX
command.
• LAMP ON VIA DMX sets the lamp to power on automatically as soon as a
DMX signal is present.
• LAMP OFF IF DMX OFF sets the lamp to power off automatically as soon
as a DMX signal is not present
Ignition delay
An ignition delay of 0 to 255 seconds can be set, so that there is a delay
between power on and lamp on:
1. Select LAMP ON DELAY and press ENTER to confirm.
2. Use the DOWN and UP buttons to set a delay duration in seconds.
3. Press ENTER to confirm (or press MENU to exit without making a
change).
Fixture information
Fixture operating hours counter
To see how many hours the fixture has been in use since manufacture:
1. Select FIXTURE HOURS and press ENTER to display the number of
hours of use.
2. Press MENU to exit.
26 RUSH Wizard User Manual
Lamp operating hours counter
The fixture has a resettable lamp hours counter that displays the number of
hours the lamp has been used. Reset the counter to zero when you install a
new lamp, and check the counter frequently. Do not exceed the lamp lifetime,
or the lamp may explode causing damage that is not covered by the product
warranty.
To see how many hours the lamp has been in use:
1. Select LAMP ON HOURS and press ENTER to display the number of
hours the lamp has been in use.
2. Press MENU to exit the counter
To reset the lamp hours counter:
1. Select LAMP ON HOURS
and press ENTER. When the hours of use are
displayed, press ENTER again and then use the UP and DOWN buttons
to select RESET TIME.
2. Press ENTER to reset the counter to zero (or press MENU to exit without
making a change).
3. Press MENU to exit.
Firmware version
To see which fixture software is currently installed in the fixture:
1. Select FIRMWARE VERSION
and press ENTER to display the installed
firmware version.
2. Press MENU to exit.
Defaults
To return the fixture to its factory default settings:
1. Select DEFAULTS and press ENTER to confirm.
2. Use the DOWN and UP buttons to select YES (return to default settings)
or NO.
3. Press ENTER to confirm (or press MENU to exit without making a
change).
RUSH Wizard User Manual 27
Reset fixture
The fixture resets each time it is powered on, but you can force it to reset at
any time. To force a reset:
1. Select RESET
2. Press ENTER to confirm (or press MENU to exit without resetting).
28 RUSH Wizard User Manual
Effects
The fixture’s effects can be controlled individually by DMX (see ‘DMX protocol’
on page 36).
Alternatively, if the fixture is set to standalone operation, you can choose from
various pre-programmed shows that use all the fixture’s effects in combination
(see ‘Standalone operation’ on page 21).
Dimming
The fixture offers 0-100 % output intensity adjustment.
Shutter
The shutter can be snapped open and closed and used for variable speed
strobe and pulse effects.
Color/animation wheel
The fixture’s color/animation wheel features seven different colors plus open
as well as a twinkle effect.
You can select static colors or you can scroll colors continuously with variable
speed. In the control menu you can set the fixture to show full colors only or
full and split colors. A random color function is also available.
Alternatively, you can select a static or dynamic twinkle effect with variable
speed.
Reflector, pan and tilt
The internal reflector dish (continuous rotation) and the mirror drum (180° of
pan and continuous rotation tilt) determine how and where the fixture’s
multiple beams are projected.
Gobo wheel
See illustration. The fixture contains a rotating wheel with 15 fixed gobos
(including four aperture gobos) plus open.
You can project any gobo statically or rotate the wheel continuously clockwise
or counter-clockwise with variable speed. A random gobo function is
available. In the control menu you can set the fixture to automatically black
out during gobo changes.
RUSH Wizard User Manual 29
You can adjust the sharpness of gobo projections manually (see ‘Focus’ on
page 20).
Gobo wheel
Effect movement
Three types of effect movement can be combined to give complex dynamic
projections:
• The internal multi-facetted reflector dish can be shaken or rotated to give
a dynamic array of multiple beams.
• The mirror drum can be shaken or rotated to give continuous tilt: the array
of rotating beams will appear to spin past in a continuous stream.
30 RUSH Wizard User Manual
• The mirror drum can be shaken or swiveled to pan the stream of dynamic
effects from side to side.
Pre-programmed effects and sound activation
On DMX channel 9 you can select from twenty pre-programmed FX that use
all the fixture’s effects or you can set the fixture to display random effects. You
can also set color and gobo shake effects that can be activated alone or
combined.
Also on DMX channel 9, you can select from various sound activation (music
trig) options in which the fixture changes scenes in time to the music beat.
If you select one of the FX on channel 9 you can adjust its speed on channel
10.
Fixture settings control via DMX
The fixture settings controls available on DMX channel 8 let you carry out the
following commands:
• Reset the fixture.
• Power the lamp on or off.
• Enable or disable Auto blackout, in which the fixture blacks out
momentarily during pan, gobo, and color changes.
• Illuminate or turn off the control panel display.
RUSH Wizard User Manual 31
Maintenance
Read ‘Safety information’ on page 4 before servicing the
fixture.
Refer any service operation not described in this user manual to
a qualified service technician.
Disconnect mains power before cleaning or servicing the fixture.
Service the fixtures in an area where there is no risk of injury
from falling parts, tools or other materials.
The user may carry out the service operations described in this manual. All
other service operations must be carried out by an authorized Martin™
service technician. Do not try to repair the fixture yourself, as you may create
a safety risk or cause damage that is not covered by the product warranty.
Installation, on-site service and maintenance can be provided worldwide by
the Martin Professional™ Global Service organization and its approved
agents, giving owners access to Martin’s expertise and product knowledge in
a partnership that will ensure the highest level of performance throughout the
product’s lifetime. Please contact Martin™ for details.
Excessive dust, smoke fluid, and particle buildup degrades performance,
causes overheating and will damage the fixture. Damage caused by
inadequate cleaning or maintenance is not covered by the product warranty.
Cleaning
The cleaning of external optical lenses must be carried out periodically to
optimize light output. Cleaning schedules for lighting fixtures vary greatly
depending on the operating environment. It is therefore impossible to specify
precise cleaning intervals for the fixture. Environmental factors that may result
in a need for frequent cleaning include:
• Use of smoke or fog machines.
• High airflow rates (near air conditioning vents, for example).
• Presence of cigarette smoke.
• Airborne dust (from stage effects, building structures and fittings or the
natural environment at outdoor events, for example).
If one or more of these factors is present, inspect fixtures within their first 100
hours of operation to see whether cleaning is necessary. Check again at
frequent intervals. This procedure will allow you to assess cleaning
32 RUSH Wizard User Manual
requirements in your particular situation. If in doubt, consult your RUSH by
Martin dealer about a suitable maintenance schedule.
Use gentle pressure only when cleaning, and work in a clean, well-lit area. Do
not use any product that contains solvents or abrasives, as these can cause
surface damage.
To clean the fixture:
1. Disconnect the fixture from power and allow it to cool for at least 30
minutes.
2. Vacuum or gently blow away dust and loose particles from the outside of
the fixture and all air vents with low-pressure compressed air.
3. Clean optical components by wiping gently with a soft, clean lint-free cloth
moistened with a weak detergent solution. Do not rub the surface hard: lift
particles off with a soft repeated press. Dry with a soft, clean, lint-free
cloth or low-pressure compressed air. Remove stuck particles with an
unscented tissue or cotton swab moistened with glass cleaner or distilled
water.
4. Check that the fixture is dry before reapplying power.
Servicing the lamp
Warning! Read ‘Lamp safety’ on page 7 before
servicing the lamp.
To avoid the risk of a discharge lamp exploding in the fixture, replace the lamp
before its expected lifetime (see ‘Lamp’ on page 45) has been exceeded.
Install only a lamp that is approved by Martin for this product.
The lamp must be perfectly clean. Do not touch the lamp’s glass bulb with
bare hands. If this happens, clean the lamp with an alcohol wipe and dry it
with a clean, lint-free cloth.
To replace the lamp:
1. Disconnect the fixture from power and allow it to cool for at least 30
minutes.
2. See illustration ‘Cover screws’. Place the fixture on a flat work surface
with its mounting bracket facing upwards and remove the 9 Phillips cover
screws (arrowed).
RUSH Wizard User Manual 33
3. Carefully turn the fixture over, catching the cover screws as they fall out of
the cover, and place the fixture with its mounting bracket facing
downwards. Lift the cover off the fixture.
Cover screws
4. The lamp consists of a bulb with an integral reflector. Do not try to
separate the bulb from the reflector. Note the position of the lamp and the
lamp wiring. Holding the spade connectors, not the wires, pull the two
spade connectors off the terminals on the back of the lamp.
34 RUSH Wizard User Manual
5. See illustration on right.
Press the lamp down
against the lamp springs
until you can pull the top of
the lamp towards the back
of the fixture and free the
lamp. Then lift the lamp out
of the fixture.
6. Put on clean lint-free cotton gloves. Press the new lamp down against the
lamp springs until you can clip the top of the lamp into position. Check
that the new lamp is held securely in the same position as the old lamp
and is roughly centered relative to the aperture in front of the lamp.
7. Taking care not to damage wires or spade connectors, install the two
spade connectors on the lamp terminals in their original positions. Check
that the spade connectors are correctly fitted onto the lamp terminals and
secure, and check that the lamp wiring is in its original position.
8. Check that all wiring is in perfect condition. If any wiring is damaged,
return the product to Martin™ for repairs.
9. Reinstall the fixture cover in its original position, fastening all 9 screws
securely.
10. Power the fixture on. Enter the LAMP ON HOURS control panel menu
and press ENTER to display the current lamp hours. Press ENTER again
and then scroll to RESET TIME. Press ENTER to reset the lamp hours
counter to zero, then press and hold MENU to exit.
11. Send the old lamp to a waste disposal center that can correctly deal with
used discharge lamps.
RUSH Wizard User Manual 35
12. If the lamp is installed as directed above, it should not require adjustment.
If projections become unsatisfactory after a lamp change, disconnect the
fixture from power and open the cover again as directed above. See
illustration below. Adjust the lamp horizontally by turning the lamp
adjustment screw (arrowed) with a flat-bladed screwdriver.
Replacing the primary fuse
If the fixture is completely dead, the fixture’s primary fuse F1 may have blown
and it may be necessary to install a new fuse. This fuse is located in a
fuseholder next to the AC mains power socket on the connections panel (see
Fixture overview on page 11).
To replace a fuse:
1. Disconnect the fixture from power and allow it to cool for at least 30
minutes.
2. Unscrew the cap of the fuseholder and remove the fuse. Replace with a
fuse of the same size and rating only.
3. Reinstall the fuseholder cap before reapplying power.
36 RUSH Wizard User Manual
DMX protocol
Chan. Value Function
Fade
type
Default
value
1
Shutter
Snap 10
0-7 Close
8-15 Open
16-131 Strobe, slowfast
132-167 Pulse effect, fast close, slow open
168-203 Pulse effect, slow close, fast open
204-239 Pulse open & close
240-247 Random strobe, slowfast
248-255 Open
2
Dimmer
Fade 0
0-255 Closed 0% open 100%
3
Color wheel: continuous scrolling
Snap 0
0 Open
1-14 Open Blue
15 Blue
16-29 Blue Magenta
30 Magenta
31-44 Magenta Yellow
45 Yellow
46-59 Yellow Dark Blue
60 Dark Blue
61-74 Dark Blue White
75 White
76-89 White Red
90 Red
91-104 Red Orange
105 Orange
106-119 Orange Green
120-158 Green
Color wheel: stepped scrolling
159 -160 Open
161-163 Blue
164-166 Magenta
167-169 Yellow
170-172 Dark Blue
173-175 White
RUSH Wizard User Manual 37
Chan. Value Function
Fade
type
Default
value
176-178 Red
179-181 Orange
182-192 Green
Continuous Rotation
193-218 Color rotation, slow fast
Animation
219-220 Twinkle static
221-243 Twinkle animated, slow fast
Random color
244-247 Random color, fast
248-251 Random color, medium
252-255 Random color, slow
4
Gobo wheel
Snap 0
0 Open
1-9 Open Gobo 1
10 Gobo 1
11-19 Gobo 1 Gobo 2
20 Gobo 2
21-29 Gobo 2 Gobo 3
30 Gobo 3
31-39 Gobo 3 Gobo 4
40 Gobo 4
41-49 Gobo 4 Gobo 5
50 Gobo 5
51-59 Gobo 5 Gobo 6
60 Gobo 6
61-69 Gobo 6 Gobo 7
70 Gobo 7
71-79 Gobo 7 Gobo 8
80 Gobo 8
81-89 Gobo 8 Gobo 9
90 Gobo 9
91-99 Gobo 9 Gobo 10
100 Gobo 10
101-109 Gobo 10 Gobo 11
110 Gobo 11
111-119 Gobo 11 Gobo 12
120 Gobo 12
121-129 Gobo 12 Gobo 13
38 RUSH Wizard User Manual
Chan. Value Function
Fade
type
Default
value
130 Gobo 13
131-139 Gobo 13 Gobo 14
140 Gobo 14
141-149 Gobo 14 Gobo 15
150 Gobo 15
151-160 Open
Stepped scrolling
161-162 Gobo 1
163-164 Gobo 2
165-166 Gobo 3
167-168 Gobo 4
169-170 Gobo 5
171-172 Gobo 6
173-174 Gobo 7
175-176 Gobo 8
177-178 Gobo 9
179-180 Gobo 10
181-182 Gobo 11
183-184 Gobo 12
185-186 Gobo 13
187-188 Gobo 14
189-190 Gobo 15
Continuous rotation
191-243 Continuous rotation, slow fast
Random gobos
244-247 Random gobos, fast
248-251 Random gobos, medium
252-255 Random gobos, slow
5
Reflector rotation (tilt)
Fade 60
0-90 Position, min. max.
91-120 Shake, slow fast
121-127 Random positions, slow fast
128-190 CW rotation, slow fast
191-192 Stop (stops at current position)
193-255 CCW rotation, slow fast
6
Mirror drum swivel (pan)
Fade 60
0-120 Position, min. max.
121-127 Shake, slow fast
128-191 Random positions, slow fast
RUSH Wizard User Manual 39
Chan. Value Function
Fade
type
Default
value
192-255 Wide shake, slow fast
7
Mirror drum rotation (tilt)
Fade 60
0-90 Position, min. max.
91-120 Shake, slow fast
121-127 Random positions, slow fast
128-190 CW rotation, slow fast
191-192 Stop (stops at current position)
193-255 CCW rotation, slow fast
8
Fixture settings
Snap 0
0-9
No function
10-14 Reset fixture
15-39
No function
40-44 Power lamp on
45-49 Power lamp off
50-144
No function
145-149 Auto blackout on (blackout during pan,
gobo and color changes)
150-154 Auto blackout off
155-159 Illuminate control panel display
160-164 Turn off control panel display
165-255
No function
9
FX
Snap 0
0-10 Open
11-15 FX 1
16-20 FX 2
21-25 FX 3
26-30 FX 4
31-35 FX 5
36-40 FX 6
41-45 FX 7
46-50 FX 8
51-55 FX 9
56-60 FX 10
61-65 FX 11
66-70 FX 12
71-75 FX 13
76-80 FX 14
81-85 FX 15
86-90 FX 16
40 RUSH Wizard User Manual
Chan. Value Function
Fade
type
Default
value
91-95 FX 17
96-100 FX 18
101-105 FX 19
106-110 FX 20
111-114
No function
115-120 Color shake
121-125 Gobo shake
126-130 Color and gobo shake
131-135 Music trig all
136-140 Music trig movement
141-145 Music trig color
146-150 Music trig gobo
151-155 Music trig color and gobo
156-160 Random FX
161-255
No function
10
FX speed
Fade 128
0-10 Stop
11-255 FX speed, slow fast
RUSH Wizard User Manual 41
Control menus
To access the control menus, press the MENU button. Use the UP and
DOWN buttons to navigate the menus. Select any required menu option using
the ENTER button. Exit using the MENU button. For more information, see
‘Using the control menus’ on page 13.
Default fixture settings are shown in bold.
Menu Setting/value Explanation
DMX Address 001–512 Fixture DMX address setting
Show Mode
Show 0 Random show
Show 1 Pre-programmed show 1
Show 2 Pre-programmed show 2
Show 3 Pre-programmed show 3
Show 4 Pre-programmed show 4
Show 5 Pre-programmed show 5
Show 6 Pre-programmed show 6
Slave Mode
Slave 1
Fixture copies the master in
master/slave operation
Slave 2
Fixture copies the master with slight
variations in master/slave operation
Split color
Yes
Split colors allowed
No Full colors only
Sound Mode
Off
Sound activation (music trig) disabled
On Sound activation (music trig) enabled
Sound Sense 0–100
Sound activation microphone
sensitivity adjustment
DMX State
Master/Slave
If no DMX signal received, fixture
enters master/slave mode
Blackout
If no DMX signal received, fixture
blacks out
Last State
If no DMX signal received, fixture
returns to last state it was in when it
was not receiving a DMX signal
Back Light
Off
Display backlight goes into sleep
mode if control panel not used
On Display backlight constantly on
Pan Reverse Yes/No Invert pan direction
Auto Test Automatic test of all effects
Lamp On/Off On/Off Manually power lamp on or off
42 RUSH Wizard User Manual
Menu Setting/value Explanation
Lamp Power
On
On/Off
Lamp powers on automatically when
fixture is powered on
Lamp Off Via
DMX
On/Off Lamp can be powered off via DMX
Lamp On Via
DMX
On/Off
Lamp powers on if DMX signal
received
Lamp Off If
DMX Off
On/Off
Lamp powers off if DMX signal not
received
Lamp On
Delay
0–255S Delay lamp ignition: 0 to 255 seconds
Fixture Hours Fixture operating hour counter
Lamp On
Hours
Exit Exit lamp hour counter
Reset Time Reset lamp hour counter to zero
Firmware
Version
Display currently installed fixture
software version
Defaults Yes/No
Return fixture to factory default
settings
Reset Reset fixture
RUSH Wizard User Manual 43
Troubleshooting
This section describes a few common problems that may occur during
operation and provides some suggestions for easy troubleshooting:
Symptom Potential cause Remedies
No light from fixture,
or fans not working.
If no DMX signal is
present, fixture may be
set to ‘Blackout’ DMX
state.
Power supply issue,
such as blown fuse,
faulty connector or
damaged cable.
Change setting in DMX
state menu.
Check whether fixture’s
power indicator LED is lit.
Check all power
connections and cables.
Replace fixture fuse.
Fixture does not
react to music beat.
Fixture not in show
mode.
Sound activation
disabled.
Sound activation
microphone sensitivity
too low for music
source.
Fixture receiving DMX.
Tap microphone to check
correct functionality. The
fixture should react when in
sound activation mode.
Set fixture to show mode in
DMX state menu.
Enable.
Adjust microphone
sensitivity.
Stop DMX signal.
44 RUSH Wizard User Manual
Symptom Potential cause Remedies
Fixture does not
respond to DMX
control.
Incorrect DMX
addressing.
Fault on DMX link due
to damaged connector
or cable, or interference
from proximity to a highvoltage installation.
Ensure that fixture’s DMX
address matches address
set on DMX control device.
Check that fixture’s DMX
LED is on, and if not, check
all cables and connections
on the DMX link.
Check that DMX link is
terminated.
Check that all devices on
the DMX link use standard
DMX polarity.
Try to control the fixture
with another DMX control
device.
Move or shield link if it is
close to an unshielded
high-voltage installation.
RUSH Wizard User Manual 45
Specifications
Physical
Weight .................................................. 9.3 kg (20.6 lbs.) including bracket
Dimensions ............................... 500 x 447 x 198 mm (19.7 x 17.6 x 7.8 in.)
Lamp
Approved lamp ....................................................... Osram Sirius HRI132W
Color temperature ............................................................................ 8800 K
Average lifetime ........................................................................ 6000 hours*
*Manufacturer’s figure
Dynamic Effects
Motorized parabolic mirror dish .................................... Continuous rotation
Motorized mirror drum ............................... 180° swivel, continuous rotation
Color/animation wheel ....... 7 colors plus 2 x open, twinkle animation effect
Gobo wheel ...................................... 15 gobos + open, wheel scrolling and
.............................................. continuous rotation, shake effect
Shutter .......................... 0 - 100% continuous dimming, variable & random
................................ strobe & pulse effects, instant open & blackout
Pre-programmed effects .................................... Full range of macro effects
Control and Programming
Control options .......................................... DMX, standalone, master/slave
DMX channels .......................................................................................... 10
Stand-alone trigger options ........................................... Music trig, auto trig
Setting and addressing ............................... Control panel with LCD display
DMX compliance ....................................................... USITT DMX512/1990
Construction
Color .................................................................................................... Black
46 RUSH Wizard User Manual
Housing .................................... High-impact flame-retardant thermoplastic
Protection rating .................................................................................. IP 20
Installation
Mounting points ................................................................ Mounting bracket
Location ........... Dry location only, must be fastened to surface or structure
Orientation ............................................................................................. Any
Minimum distance to combustible materials ........................ 100 mm (4 in.)
Minimum distance to illuminated surfaces ........................ 200 mm (7.9 in.)
Connections
AC power input/throughput............................................. Neutrik PowerCon
DMX data input/throughput ............................................. 5-pin locking XLR
Electrical
AC power ....................................................... 100-240 V nominal, 50/60 Hz
Fuse .................................................................................................. T 6.3 A
Power supply unit .............................. Auto-ranging electronic switch mode
Power consumption figures are typical, not maximum. Allow for +/-10%
variation
Typical power and current
110 V, 60 Hz .............................................................. 1.9 A, 200 W, PF0.99
230 V, 50 Hz ............................................................. 0.9 A, 196 W, PF 0.95
Thermal
Cooling ........................................................................................ Forced air
Maximum ambient temperature (T
a
max.) ............................ 40° C (104° F)
Minimum ambient temperature (T
a
min) .................................... 0°C (32° F)
Total heat dissipation* .............................................................. 685 BTU/hr.
*Calculated, +/- 10%
Approvals
EU safety .................. EN 60598-2-17 (EN 60598-1), EN 62471, EN 62493
EU EMC............................................... EN 55015, EN 55032, EN 55103-2,
...................................... EN 61000-3-2, EN 61000-3-3, EN 61547
US safety ........................................................................................ UL 1573
US EMC...................................................................... FCC Part 15 Class A
Canadian safety .................... CSA C22.2 No. E598-2-17 (CSA E60598-1)
Canadian EMC ............................................................... ICES-003 Class A
Australia/NZ .......................................................................... C-TICK N4241
RUSH Wizard User Manual 47
Included Items
Power cable, 6 A, 18 AWG, 0.75 mm
2
, UL- listed, H05VV-F,
1.5 m (without mains plug)
Folding bracket
Discharge lamp (installed)
Accessories
Cables, 16 A, for connection to power in chains
Power input cable, 14 AWG, SJT, 1.5 mm2, H05VV-F,
with PowerCon input connector, 3 m (9.8 ft.) ..................... P/N 11541508
Power relay cable, 14 AWG, SJT, 1.5 mm2, H05VV-F,
with PowerCon connectors, 1.4 m (4.6 ft.) ......................... P/N 11541509
Power relay cable, 14 AWG, SJT, 1.5 mm2, H05VV-F,
with PowerCon connectors, 2.25 m (7.4 ft.) ....................... P/N 11541510
Power relay cable, 14 AWG, SJT, 1.5 mm2, H05VV-F,
with PowerCon connectors, 3.25 m (10.7 ft.) ..................... P/N 11541511
Power connectors
Neutrik PowerCon NAC3FCA
power input connector, cable mount, blue ......................... P/N 05342804
Neutrik PowerCon NAC3FCB
power output connector, cable mount, light grey ............... P/N 05342805
Installation hardware
Half-coupler rigging clamp.................................................... P/N 91602005
Safety cable, safe working load 50 kg .................................. P/N 91604003
Related Items
RUSH Software Uploader 1™ .............................................. P/N 91611399
Ordering Information
RUSH Wizard™ in cardboard box, EU model ...................... P/N 90480070
RUSH Wizard™ in cardboard box, US model ...................... P/N 90480075
Specifications are subject to change without notice. For the latest product
specifications, see www.martin.com
Disposing of this product
RUSH by Martin™ products are supplied in compliance with Directive 2012/19/EC
of the European Parliament and of the Council of the European Union on WEEE
(Waste Electrical and Electronic Equipment), where applicable. Help preserve the
environment! Ensure that this product is recycled at the end of its life. Your
supplier can give details of local arrangements for the disposal of RUSH by Martin
products.
Innovation Quality Performance
Loading...