Runco SP-42DHD, SP-50DHD, SP-60DHD, SP-42DHDXA, SP-50DHDXA User Manual

OWNER’S OPERATING MANUAL

SP-42DHD / SP-42DHDxa

TM

SP-50DHD / SP-50DHDxa
SP-60DHD / SP-60DHDxa

Flat Panel Plasma Display Monitor

with

and

Digital High Definition

with Vivix IITM Technology

TM

Controller

THREE YEAR LIMITED WARRANTY

For Plasma Displays

Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces
“The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of
unparalleled video performance.

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your
other important documents.

WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma
glass panel).

PARTS (not including plasma glass panel): Runco will provide new or rebuilt replacement parts for the parts that fail due to
defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such
replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Runco will
provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1)
year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the
remaining portion (if any) of the original warranty period.

Y

IMINAR

WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is
the result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.

Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of
time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers
for this reason.

L

PRE

TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more
than a few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture
information is present on the left and right edges of the screen) are used as infrequently as possible. This will prevent
permanent image burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in
has occurred.

The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This
is why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after
being displayed continuously for an extended period of time).

This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does
not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and
brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote
control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this
Limited Warranty.

CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED
DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY.

PlasmaWall SP Series Owner’s Operating Manual iii

MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS
SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION
AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER
THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE OF WHICH YOUR RUNCO
PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.

RIGHTS, LIMITS AND EXCLUSIONS:

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to
the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.

IMPORTANT – WARRANTY REGISTRATION:

Y

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we
should discover a safety problem or product update for which you must be notified.

CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:

Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Runco
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for
repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest
Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s
responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco
Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will
return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping
costs will be the responsibility of the owner.

COPYRIGHT AND TRADEMARKS:

© Copyright 2007 Runco International. This document contains proprietary information protected by copyright, trademark and
other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.

Reflection, Enhanced GEN3, DHD, Vivix, Virtual Cinema, CineWide, AutoScope, O-Path, CinOptx, LiveLink, CSMS, SuperOnyx
and VirtualWide are trademarks of Runco International. All other trademarks and registered trademarks used in this document
are the property of their respective owners.

PRE

IMINAR

L

Runco International products are manufactured under one or more of the following patents: US. Patent 6755540 and Other
Patents Pending.

iv PlasmaWall SP Series Owner’s Operating Manual

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this
Limited Warranty, please call or write:

RUNCO INTERNATIONAL, INC.

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: [phone]

Y

Fax: [phone]

Toll Free: (800) 23-RUNCO

RUNCO VIDEO-PRODUCT INFORMATION

RETAIN THIS INFORMATION FOR YOUR RECORDS

IMINAR

_________________________________________________________ ________________________________________

L

Model Purchased Date

____________________________________________________________________________________________________________

Serial Number

____________________________________________________________________________________________________________

Runco Authorized Dealer Name

____________________________________________________________________________________________________________

PRE

Address

____________________________________________ __________________ ________________________

City State/Province Postal Code

____________________________________________ _________________________________________________________

Phone Fax

PlasmaWall SP Series Owner’s Operating Manual v

Safety Precautions

Thank you for your purchase of this quality Runco product! It has been designed to provide you with the quality of video that is
expected in a home theater. This manual is your guide through the menus and operation. For the best performance, please
read it carefully and keep it handy for future reference.

WARNING

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

CAUTION

To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to
the equipment as possible, and should be easily accessible.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN
BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION:

SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

Y

IMINAR

L

WARNING

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
Installation Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area
may cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no
injury will occur as a result of improper use.

• Do not insert any object, especially metal or liquids, into the plasma display.

• Do not place any objects containing water or any other liquid on top of the plasma display.

• Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.

• Do not install this system outdoors or otherwise exposed to the elements.

• Do not place heavy objects on top of the plasma display.

• If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the
power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way,
please contact your Runco Dealer for a replacement cord.

• Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Runco
Dealer or Runco International for service. Removing the covers will void the warranty.

PRE

vi PlasmaWall SP Series Owner’s Operating Manual

1Table of Contents

THREE YEAR LIMITED WARRANTY ............................................................................. iii

Safety Precautions ......................................................................................................... vi

1. Introduction ............................................................................................................... 1

About This Manual ....................................................................................................... 1

Target Audience ..................................................................................................... 1

If You Have Comments About This Manual... ..........................................................1

Textual and Graphic Conventions ...........................................................................1

Using This Manual ........................................................................................................ 2

Description, Features and Benefits ...............................................................................3

Key Features and Benefits ...................................................................................... 3

Parts List ...............................................................................................................4

2. Controls and Functions ............................................................................................5

PlasmaWall at a Glance ................................................................................................ 5

Controls and Indicators ...........................................................................................5

Connectors ............................................................................................................6

DHD Controller Front Panel ........................................................................................10

DHD Controller Rear Panel ......................................................................................... 12

Outputs ................................................................................................................ 12

Inputs ...................................................................................................................12

DHD Controller Remote Control ................................................................................. 14

PRE

3. Installation ...............................................................................................................17

Remote Control ..........................................................................................................17

IMINAR

L

Y

Notes on Batteries ................................................................................................ 17

Notes on Remote Control Operation .....................................................................17

Quick Setup ............................................................................................................... 19

Installation Considerations ..........................................................................................20

High-Altitude Operation ........................................................................................ 20

Mounting the PlasmaWall on a Wall or Table Stand ..............................................20

Ambient Light .......................................................................................................21

Ventilation ............................................................................................................. 21

Other Considerations ............................................................................................ 22

Connections to the PlasmaWall and DHD Controller ................................................... 23

Connecting the PlasmaWall to the DHD Controller ................................................ 23

PlasmaWall SP Series Owner’s Operating Manual vii

Table of Contents

Connecting Source Components to the DHD Controller ....................................... 25

RS-232 Controller Connection .............................................................................. 29

Connecting 12-Volt Trigger Outputs to External Equipment .................................. 29

Cable Management .............................................................................................. 30

4. Operation ................................................................................................................. 31

Turning on the Power ................................................................................................. 31

Selecting the Input Source .........................................................................................32

Setting the Computer Display Properties .................................................................... 32

Using the On-Screen Menus ......................................................................................34

Main Menu ...........................................................................................................36

Input Source ........................................................................................................ 36

Aspect Ratio ........................................................................................................ 36

Picture .................................................................................................................38

Input Position........................................................................................................ 41

ISF Presets ........................................................................................................... 42

Information ........................................................................................................... 42

Calibration ............................................................................................................43

Service ................................................................................................................. 45

5. Maintenance and Troubleshooting ........................................................................ 49

Cleaning .....................................................................................................................49

Cleaning the Display Panel Body and Remote Control ..........................................49

Cleaning the Screen.............................................................................................. 49

Cleaning the Vents................................................................................................ 49

Troubleshooting Tips ..................................................................................................50

PRE

6. Serial Communications ..........................................................................................53

RS-232 Connection and Port Configuration ...............................................................53

IMINAR

L

Y

Serial Command Syntax ............................................................................................. 53

7. Specifications .......................................................................................................... 59

PlasmaWall Specifications .......................................................................................... 59

DHD Controller Specifications .................................................................................... 60

PlasmaWall Dimensions ............................................................................................. 61

Computer/Video Signal Compatibility .........................................................................64

APPENDIX A. PlasmaWall Service Remote Control ................................................. A-1

Overview .................................................................................................................. A-1

Service/Setup Menu ................................................................................................. A-3

Video NR (Noise Reduction) ................................................................................ A-3

MPEG Filter ........................................................................................................ A-4

viii PlasmaWall SP Series Owner’s Operating Manual

1List of Figures

2-1. PlasmaWall Front-Panel Controls and Indicators........................................................... 5

2-2. PlasmaWall Model SP-42DHD Rear Panel ....................................................................6

2-3. PlasmaWall Model SP-50DHD Rear Panel ....................................................................7

2-4. PlasmaWall Model SP-60DHD Rear Panel ....................................................................8

2-5. DHD Controller Front Panel ........................................................................................10

2-6. DHD Controller Rear Panel .........................................................................................12

2-7. DHD Controller Remote Control ................................................................................. 14

3-1. Available Range of the Remote Control ...................................................................... 17

3-2. Ventilation Requirements for Enclosure Mounting ....................................................... 21

3-3. Connecting the PlasmaWall to the DHD Controller .....................................................23

3-4. RS-232 Connection from the DHD Controller to the PlasmaWall ................................24

3-5. DVI Source Connections ............................................................................................ 25

3-6. Digital (DTV) RGB Connections...................................................................................26

3-7. Analog RGB Connections...........................................................................................27

3-8. Composite, S-Video and Component Video Connections........................................... 28

3-9. RS-232 Control System Connection........................................................................... 29

3-10. Connecting 12-Volt Trigger Outputs ......................................................................... 29

3-11. Installing the Cable Ties ............................................................................................30

4-1. DHD Controller OSD Menu Structure for PlasmaWall.................................................. 35

4-2. Typical PLUGE Pattern for Adjusting Brightness .........................................................38

PRE

4-3. Typical Gray Bar Pattern for Adjusting Contrast .......................................................... 39

4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................40

IMINAR

L

Y

4-5. Typical Test Pattern for Adjusting Sharpness..............................................................41

7-1. PlasmaWall Model SP-42DHD Dimensions (with Optional Table Stand) ......................61

7-2. PlasmaWall Model SP-50DHD Dimensions (with Optional Table Stand) ......................62

7-3. PlasmaWall Model SP-60DHD Dimensions (with Optional Table Stand) ......................63

A-1. PlasmaWall Service Remote Control ........................................................................ A-1

A-2. PlasmaWall Setup Menu .......................................................................................... A-3

PlasmaWall SP Series Owner’s Operating Manual ix

List of Figures

Notes:

Y

IMINAR

L

PRE

x PlasmaWall SP Series Owner’s Operating Manual

1. Introduction

This Owner’s Manual describes how to install, set up and operate a Runco PlasmaWall
Flat-Panel Plasma Display Monitor and DHD Controller (Model SP-42DHD, SP-42DHDxa,
SP-50DHD, SP-50DHDxa, SP-60DHD or SP-60DHDxa).

Throughout this manual, the Runco PlasmaWall Flat-Panel Plasma Display Monitor and
DHD Controller are referred to collectively as the “PlasmaWall.” Except where otherwise
indicated, the information in this manual applies to all six PlasmaWall models.

Y

most out of the PlasmaWall.

Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
other Runco product manuals on-line, at www.runco.com.

Runco welcomes your comments about this manual. Send them to [e-mail].

Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:

• Remote control button identifiers are set in upper-case bold type; for example, “Press
EXIT to return to the previous menu.”

• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Anamorphic, type ANAMORPHIC <Enter>.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc>
and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your
computer keyboard if it has both keys.

PRE

IMINAR

L

1.1 About This Manual

Target AudienceRunco has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:

Note

PlasmaWall SP Series Owner’s Operating Manual 1

A carriage return must be used after each command or string.

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:

1.2

Using This Manual

Tip

Note

Caution

TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.

NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.

CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.

Y

WARNING

DANGER!

Use the following table to locate the specific information you need in this manual.

WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or
death.

IMINAR

If you need... ... Turn to page:

Information about obtaining service iv

L

General information about the PlasmaWall
Flat-Panel Plasma Display Monitor and DHD Con­troller

Installation instructions 17

PRE

First-time configuration instructions 31

Advanced configuration instructions 43

Troubleshooting tips 50

Specifications for the PlasmaWall Flat-Panel
Plasma Display Monitor and DHD Controller

3

59

2 PlasmaWall SP Series Owner’s Operating Manual

Introduction

The PlasmaWall SP Series flat-panel plasma monitor brings outstanding picture quality to
its size category with true, high-definition native resolution of up to 1365 x 768
(1024

x 768 on the Model SP-42DHD) for no-compromise viewing of any video source.

The PlasmaWall is supplied with Runco’s next-generation, Digital High Definition (DHD)
Controller, featuring advanced Vivix II™ processing. This controller produces stunning
video imagery, elevating even standard NTSC material to near high-definition levels.

Multiple aspect ratio control includes Runco’s VirtualWide™ for viewing 4:3 material in
widescreen with no loss of picture quality. The DHD provides for a pure digital signal path
from input to output, making this system ready for Runco’s exclusive LiveLink™ DVI cable
solution to preserve HD signal quality over long runs.

The PlasmaWall’s black level performance and shadow detail capability have been
enhanced with Active Gray Scale Rendering to provide smoother transitions from dark to
light, resulting in richly detailed textures even in shadowy scenes.

The PlasmaWall is easily integrated into custom installation systems. Both RS-232C and
IR control interfaces are incorporated for simple automation. Its profile is less than 5-1/2
inches thin for wall-mounting simplicity.

For high-altitude installations, Runco also offers the SP-42DHDxa, SP-50DHDxa and
SP-60DHDxa with industry-leading high-altitude compliance to over 9000 feet (2,740
meters) mean sea level (MSL). The SP-42DHDxa, SP-50DHDxa and SP-60DHDxa share
all other features and specifications with the SP-42DHD, SP-50DHD and SP-60DHD
respectively.

Y

IMINAR

• 16:9 Native Resolution: 1024 x 768 (Model SP-42DHD) or 1365 x 768
(Models

• Multiple Aspect Ratios with VirtualWide™ Mode

• 160 degree horizontal/vertical viewing angle

• Accepts all DTV formats (via outboard decoder), including 1080i, 720p and 480p

• Less than 5-1/2 inches deep

• Two DVI Inputs (on DHD Controller) with High-bandwidth Digital Content Protection
(HDCP)

• Exceptional detail and artifact-free video enhancement

• Vivix™ video processing with 3:2 film detection circuitry

SP-50DHD and SP-60DHD)

PRE

L

1.3 Description, Features and Benefits

Key Features and BenefitsThe PlasmaWall offers these key features and benefits:

PlasmaWall SP Series Owner’s Operating Manual 3

Introduction

Parts List Your PlasmaWall is shipped with the following items. If any items are missing or damaged,

➤

please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.

• PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller

• AC Power Cords (2)

• Remote Control Unit and two (2), AAA-size batteries

• Service Remote Control Unit and two (2), AA-size batteries

• RJ-11 Telephone Cable, 50 feet (15.24 meters)

• Serial Port Adapter, RJ-11 Female to DB-9 Female

• Rack-mount hardware for the DHD Controller

• Cleaning Cloth

• Cable Ties (2)

• Warranty information and registration card

• PlasmaWall SP Series Owner’s Operating Manual (this document)

Optional Accessories:

• Wall Mount Kit – part number RUHK-004300 (SP-42DHD/SP-50DHD) or
RUHK-003800 (SP-60DHD)

• Table Stand – part number RUHK-004400 (SP-42DHD/SP-50DHD) or RUHK-003850
(SP-60DHD)

• LiveLink™ DVI Cabling System

Y

IMINAR

L

PRE

4 PlasmaWall SP Series Owner’s Operating Manual

(SP-42DHD/SP-50DHD)

4

(SP-60DHD)

4

2. Controls and Functions

2.1 PlasmaWall at a Glance

Controls and IndicatorsFigure 2-1 shows the PlasmaWall front-panel controls and indicators.

Y

IMINAR

L

1

PRE

Figure 2-1. PlasmaWall Front-Panel Controls and Indicators

1. DISPLAY STAN D

Optional accessory for tabletop installations.

2. REMOTE CONTROL SENSOR

Receives the signals from the remote control.

3. STANDBY/ON INDICATOR

- Lights green to indicate normal operation;

- Lights red to indicate that the PlasmaWall is in standby mode;

- Flashes green or red (twice per second) to indicate an error condition.

4. HANDLES

ALWAYS use the handles when carrying the unit.

2

3

PlasmaWall SP Series Owner’s Operating Manual 5

Controls and Functions

Connectors Figure 2-2 and Figure 2-3 show the rear-panel connector and power switch locations on

➤

the SP-42DHD and SP-50DHD respectively.

9 10 11 12

Y

IMINAR

L

IN OUT

PRE

COMBINATION

1 2 3 4 5 6 7 8

Figure 2-2. PlasmaWall Model SP-42DHD Rear Panel

RS-232C

INPUT1

OUTPUT INPUT2

AUDIO

AUDIO AUDIO

ANALOG RGB OUT

(D-Sub)

INPUT1

ANALOG RGB IN

(D-Sub)

INPUT2

DIGITAL RGB
(DVI-D)

6 PlasmaWall SP Series Owner’s Operating Manual

Controls and Functions

11

12

Y

IN OUT

COMBINATION

IMINAR

RS-232C

INPUT1

OUTPUT INPUT2

AUDIO

AUDIO AUDIO

ANALOG RGB OUT

(D-Sub)

INPUT1

ANALOG RGB IN

(D-Sub)

INPUT2

DIGITAL RGB
(DVI-D)

L

9 10 1 2 3 4 5 6 7 8

Figure 2-3. PlasmaWall Model SP-50DHD Rear Panel

PRE

PlasmaWall SP Series Owner’s Operating Manual 7

Controls and Functions

1211

Y

IN OUT

L

1

COMBINATION

9

10

RS-232C

2

PRE

Figure 2-4. PlasmaWall Model SP-60DHD Rear Panel

IMINAR

INPUT1

OUTPUT INPUT2

AUDIO

AUDIO AUDIO

3 4 5 6 7

ANALOG RGB OUT

(D-Sub)

INPUT1

ANALOG RGB IN

(D-Sub)

INPUT2

DIGITAL RGB
(DVI-D)

8

8 PlasmaWall SP Series Owner’s Operating Manual

1. COMBINATION IN/OUT

Not used.

2. RS-232C (9-pin, male D-Sub)

Connect the RS-232 OUT port on the DHD Controller to this input.

3. AUDIO (OUTPUT) (3.5-mm stereo mini jack)

Not used with this model.

4. AUDIO (INPUT 1) (3.5-mm stereo mini jack)

Not used with this model. Connect the audio outputs from your sources to an external
audio receiver.

5. AUDIO (INPUT 2) (3.5-mm stereo mini jack)

Not used with this model. Connect the audio outputs from your sources to an external
audio receiver.

6. ANALOG RGB OUT (INPUT 1) (15-pin D-Sub)
If desired, connect this output to the RGB input of a second display device.

Controls and Functions

Y

Note

7. ANALOG RGB IN (INPUT 1) (15-pin D-Sub)
Connect the RGBHV (5xBNC) output from the DHD Controller here.

8. DIGITAL RGB (INPUT 2) (DVI-D)
HDCP-compliant digital video input. Connect the DVI output from the DHD

Controller to this input.

This output is not active when the PlasmaWall is off or in standby
mode.

IMINAR

9. EXTERNAL SPEAKER OUTPUT (RIGHT)
Not used. Connect speakers to an external audio amplifier/receiver.

10. EXTERNAL SPEAKER OUTPUT (LEFT)
Not used. Connect speakers to an external audio amplifier/receiver.

11. POWER INPUT (100 to 240 VAC)
Connect the PlasmaWall to power here, using the included power cord.

12. MAIN POWER SWITCH
Connects or disconnects the PlasmaWall from the AC power source.

PRE

L

PlasmaWall SP Series Owner’s Operating Manual 9

Controls and Functions

2.2

DHD Controller Front Panel

1

Figure 2-5. DHD Controller Front Panel

2

Figure 2-5 shows the controls and indicators on the DHD Controller front panel; the
paragraphs that follow describe them.

1. RUNCO ICON

Lights red to indicate that the DHD Controller is in standby mode; lights blue to
indicate that the unit is on.

2. POWER BUTTON

Press once to toggle from standby mode to on mode. Press it again to return to
standby mode. For a discrete on or off command, you can use the direct access
buttons on the remote control.

Y

3

45

6

7

IMINAR

L

8

9

10

3. IR SENSOR

Receives IR commands from the remote.

4. VACUUM FLUORESCENT DISPLAY

Can be used instead of the On-Screen Display (OSD). Displays currently-selected

PRE

menu or – if no menu is selected – the current source, signal format (NTSC or PAL),
input resolution and aspect ratio.

10 PlasmaWall SP Series Owner’s Operating Manual

5. UP BUTTON
Use to direct-select aspect ratios or move the menu cursor up in the OSD. When no
menu is present on-screen, the UP button toggles through aspect ratios in the
following order:
Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema

(For more information about aspect ratios, refer to Table 4-1.)

6. LEFT BUTTON
Used to direct-select inputs or move the menu cursor left in the OSD. When no menu
is present on-screen, the LEFT button toggles through the different sources, in this
order:
HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 ­Component SD - S-Video 2 - S-Video 1 - Composite

Controls and Functions

7. ENTER BUTTON
When an item is highlighted on the OSD, press ENTER to select it.

8. DOWN BUTTON
Use to direct-select aspect ratios or move the menu cursor down in the OSD. When
no menu is present on-screen, the DOWN button toggles through the different aspect
ratios, in this order:
Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

9. RIGHT BUTTON
Used to direct-select inputs or move the menu cursor right in the OSD. When no
menu is present on-screen, the RIGHT button toggles through the different sources,
in this order:
Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1

- DVI

2 - HD Pass Thru 1 - HD Pass Thru 2

10. MENU BUTTON
Pressing the MENU button brings up the main menu. Also, if you are in an adjustment
mode or function, pressing MENU brings the menu back one level.

IMINAR

L

PRE

Y

PlasmaWall SP Series Owner’s Operating Manual 11

Controls and Functions

2.3

Figure 2-6 shows the rear connector panel on the DHD Controller.

DHD Controller Rear Panel

Serial No

Runco International

Union City, CA

OUTPUTS

R/Pr G/Y B/Pb

1

Model

Video Processor / Controller

2

Figure 2-6. DHD Controller Rear Panel

Outputs 1. ANALOG OUTPUTS (RGBHV)

Inputs 3. DVI 1 / DVI 2 (Digital)

➤

➤

R/Pr G/Y B/Pb

R/Pr G/Y B/Pb H V

2. DVI OUT

810

4

INPUTS

DVI 1 DVI 2DVI OutH/VVH

3

HV

HD1

HD2

SDI

Pb Pr Y

Component Video

Option

5

SYSTEM CONTROL INTERFACE

TRIGGERS

2

1

S-Video 1

Video

6

RS-232 Out

S-Video 2

7

3

WARNING:

OR ELECTRIC SHOCK, DO NOT EXPOSE

Y

THIS APPLIANCE TO RAIN OR MOISTURE.

RS-232 Control

9

IR

TO REDUCE THE RISK OF FIRE

11

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION:

TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO USER­SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.

100-230VAC 50-60 Hz, 165 Watts Max

Made In USA

12

13 14

!

Connect these to the ANALOG RGB IN input of the PlasmaWall, using a
5

x BNC-to-VGA breakout cable.

IMINAR

Connect this to the DIGITAL RGB (DVI-D) input on the PlasmaWall.

L

Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner
with a DVI or HDMI output.

4. HD1 / HD2 (5 x Analog BNCs)

Two inputs (five BNCs per input) for connecting either RGB or component

PRE

high-definition television signals. The DHD Controller automatically detects the signal
format: RGB(HV) or YPrPb, 480p, 720p, 480i, 576i or 1080i.

5. COMPONENT VIDEO (RCA connectors)

Standard Definition (480i/576i) Component (YPrPb) input. This is the input for
component video from sources such as DVD players.

Tip

For best results, do not run your DVD player in progressive mode.

12 PlasmaWall SP Series Owner’s Operating Manual

6. COMPOSITE VIDEO INPUT

Standard composite video input for connecting a VCR, camcorder, laser disc player
or other composite video source.

7. S-VIDEO 1 / S-VIDEO 2

Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super
VHS (S-VHS) VCR.

8. 12-VOLT (750 mA) TRIGGER OUTPUTS

Connection for up to three (3), 12-volt trigger-controlled devices.

9. RS-232 OUTPUT (6-Wire, RJ-11 jack)

Connect this to the RS-232C input of the PlasmaWall, using the supplied serial port
adapter and communication cable.

10. IR

Wired input from an external remote control or infrared receiver. It is a 3.5-mm, mini
phono jack, wired as follows:
Ring = +5V
Tip = IR Input
Sleeve = Ground

Controls and Functions

Y

Note

11. RS-232 CONTROL PORT

A female, 9-pin D-sub connector for interfacing with a PC or home theater
automation/control system.

12. POWER INPUT (100 to 240 VAC)

Connect the DHD Controller to power here.

13. MAIN AC FUSE

This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow).

14. MAIN POWER SWITCH

Disconnects or applies power to the DHD Controller.

When an external remote control or infrared receiver is connected
to the wired IR input, the IR sensor on the front of the DHD
Controller is disabled.

IMINAR

L

PRE

PlasmaWall SP Series Owner’s Operating Manual 13

Controls and Functions

2.4 DHD Controller Remote Control

Figure 2-7 shows the DHD Controller remote control, and the paragraphs that follow
describe its functionality.

2

1

3

4

5

7

10

11

12

6

8

IMINAR

9

L

Y

13

PRE

Figure 2-7. DHD Controller Remote Control

14 PlasmaWall SP Series Owner’s Operating Manual

1. IR OUTPUT INDICATOR

Lights when a button is pressed to indicate that an IR signal is being transmitted.

2. ON / OFF

Press to turn the PlasmaWall on or off.

3. ENTER

Press to select a highlighted menu item or confirm a changed setting.

4. Cursor Keys ( , , , )

Use these buttons to select items or settings, adjust settings or switch display
patterns.

When no menus are present on-screen, the UP and DOWN buttons toggle through
the available aspect ratios, in this order:

UP Button = Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema
DOWN Button = Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in
this order:
LEFT Button = HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 ­HD/RGB 1 - Component SD - S-Video 2 - S-Video 1 - Composite
RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 -
HD/RGB 2 - DVI 1 - DVI 2 - HD Pass Thru 1 - HD Pass Thru 2

5. LIGHT

Press to illuminate the buttons.

Controls and Functions

Y

6. MENU

Press this button to access the OSD controls, or to exit the current menu and return
to the previous one.

7. VIDEO (1)

Press to select Composite video input as the source or to enter the numeric
character

8. COMP (Component) (2)

Press to select Component SD (480i/576i) video input as the source or to enter the
numeric character “2.”

“1.”

IMINAR

L

PRE

PlasmaWall SP Series Owner’s Operating Manual 15