Runco PL-43DHD User Manual

Download

OWNER’S OPERATING MANUAL

PL-43DHD

PL-50DHD

Flat Panel Plasma Display Monitor

with

and

Digital High Definition

with Vivix IITM Technology

Software Version 2.00

Controller

THREE YEAR LIMITED WARRANTY

For Plasma Displays

Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of unparalleled video performance.

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents.

WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma glass panel).

PARTS (not including plasma glass panel): Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1) year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

IMINAR

WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is the result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.

Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers for this reason.

PRE

TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more than a few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture information is present on the left and right edges of the screen) are used as infrequently as possible. This will prevent permanent image burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in has occurred.

The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This is why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after being displayed continuously for an extended period of time).

This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this Limited Warranty.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual iii

CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY.

RIGHTS, LIMITS AND EXCLUSIONS:

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date.

IMPORTANT – WARRANTY REGISTRATION:

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.

IMINAR

CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:

Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of the product, during usual working hours, providing location of product is within normal operating distance from a Runco Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner.

© Copyright 2006 Runco International. This document contains proprietary information protected by copyright, trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer.

Reflection, Enhanced GEN3, DHD, Vivix, Virtual Cinema, CineWide, AutoScope, O-Path, CinOptx, LiveLink, CSMS, SuperOnyx and VirtualWide are trademarks of Runco International. All other trademarks and registered trademarks used in this document are the property of their respective owners.

Runco International products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents Pending.

PRE

iv Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limited Warranty, please call or write:

RUNCO INTERNATIONAL, INC.

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: (510) 324-7777

Fax: (510) 324-9300

Toll Free: (800) 23-RUNCO

RUNCO VIDEO-PRODUCT INFORMATION

RETAIN THIS INFORMATION FOR YOUR RECORDS

IMINAR

_________________________________________________________ ________________________________________

Model Purchased Date

____________________________________________________________________________________________________________

Serial Number

____________________________________________________________________________________________________________

Runco Authorized Dealer Name

____________________________________________________________________________________________________________

PRE

Address

____________________________________________ __________________ ________________________

City State/Province Postal Code

____________________________________________ _________________________________________________________

Phone Fax

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual v

Safety Precautions

Thank you for your purchase of this quality Runco product! It has been designed to provide you with the quality of video that is expected in a home theater. This manual is your guide through the menus and operation. For the best performance, please read it carefully and keep it handy for future reference.

WARNING

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

CAUTION

To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION:

SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMINAR

WARNING

This equipment has been tested and found to comply with the limits for a Class ‘B’ digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at his own expense.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no injury will occur as a result of improper use.

• Do not insert any object, especially metal or liquids, into the plasma display.

• Do not place any objects containing water or any other liquid on top of the plasma display.

• Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.

• Do not install this system outdoors or otherwise exposed to the elements.

• Do not place heavy objects on top of the plasma display.

• If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way, please contact your Runco Dealer for a replacement cord.

• Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Runco Dealer or Runco International for service. Removing the covers will void the warranty.

PRE

vi Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

1Table of Contents

THREE YEAR LIMITED WARRANTY ............................................................................. iii

Safety Precautions ......................................................................................................... vi

1. Introduction ............................................................................................................... 1

About This Manual ....................................................................................................... 1

Target Audience ..................................................................................................... 1

If You Have Comments About This Manual... ..........................................................1

Textual and Graphic Conventions ...........................................................................1

Using This Manual ........................................................................................................ 2

Description, Features and Benefits ...............................................................................3

Key Features and Benefits ...................................................................................... 3

Parts List ...............................................................................................................4

2. Controls and Functions ............................................................................................5

PlasmaWall at a Glance ................................................................................................ 5

Controls and Indicators ...........................................................................................5

Connectors ............................................................................................................6

DHD Controller Front Panel ..........................................................................................8

DHD Controller Rear Panel ......................................................................................... 10

Outputs ................................................................................................................ 10

Inputs ...................................................................................................................10

DHD Controller Remote Control ................................................................................. 12

IMINAR

PRE

3. Installation ............................................................................................................... 15

Remote Control ..........................................................................................................15

Notes on Batteries ................................................................................................ 15

Notes on Remote Control Operation .....................................................................15

Quick Setup ............................................................................................................... 17

Installation Considerations ..........................................................................................18

High-Altitude Operation ........................................................................................ 18

Mounting the PlasmaWall on a Wall or Table Stand ..............................................18

Ambient Light .......................................................................................................19

Ventilation ............................................................................................................. 19

Other Considerations ............................................................................................ 20

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual vii

Connections to the PlasmaWall and DHD Controller ................................................... 21

Connecting the PlasmaWall to the DHD Controller ................................................ 21

Connecting Source Components to the DHD Controller ....................................... 23

RS-232 Controller Connection .............................................................................. 27

Connecting 12-Volt Trigger Outputs to External Theater Components ..................27

Cable Management .............................................................................................. 28

4. Operation ................................................................................................................. 29

Turning on the Power ................................................................................................. 29

Selecting the Input Source .........................................................................................30

Setting the PC Display Properties ...............................................................................30

Using the On-Screen Menus ......................................................................................32

Main Menu ...........................................................................................................34

Input Source ........................................................................................................ 34

Aspect Ratio ........................................................................................................ 34

Picture .................................................................................................................36

Input Position........................................................................................................ 39

ISF Presets ........................................................................................................... 40

Information ........................................................................................................... 40

Calibration ............................................................................................................41

Service ................................................................................................................. 42

5. Maintenance and Troubleshooting ........................................................................ 47

Troubleshooting Tips ..................................................................................................47

6. Serial Communications ..........................................................................................49

RS-232 Connection and Port Configuration ...............................................................49

PRE

Serial Command Syntax ............................................................................................. 49

7. Specifications .......................................................................................................... 55

IMINAR

PlasmaWall Specifications .......................................................................................... 55

DHD Controller Specifications .................................................................................... 56

PlasmaWall Dimensions ............................................................................................. 57

Computer/Video Signal Compatibility .........................................................................59

APPENDIX A. PlasmaWall Service Remote Control ..................................................A-1

Overview .................................................................................................................. A-1

Service/Setup Menu ................................................................................................. A-2

Video NR (Noise Reduction) ................................................................................ A-3

MPEG Filter ........................................................................................................ A-3

viii Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

1List of Figures

2-1. PlasmaWall Front-Panel Controls and Indicators........................................................... 5

2-2. PlasmaWall Connectors ............................................................................................... 6

2-3. DHD Controller Front Panel ..........................................................................................8

2-4. DHD Controller Rear Panel .........................................................................................10

2-5. DHD Controller Remote Control ................................................................................. 12

3-1. Available Range of the Remote Control ...................................................................... 15

3-2. Ventilation Requirements for Enclosure Mounting ....................................................... 19

3-3. Connecting the PlasmaWall to the DHD Controller .....................................................21

3-4. RS-232 Connection from the DHD Controller to the PlasmaWall ................................22

3-5. DVI Source Connections ............................................................................................ 23

3-6. Digital (DTV) RGB Connections...................................................................................24

3-7. Analog RGB Connections...........................................................................................25

3-8. Composite, S-Video and Component Video Connections........................................... 26

3-9. RS-232 Control System Connection........................................................................... 27

3-10. Connecting 12-Volt Trigger Outputs ......................................................................... 27

3-11. Installing the Cable Ties ............................................................................................28

4-1. DHD Controller OSD Menu Structure for PlasmaWall.................................................. 33

4-2. Typical PLUGE Pattern for Adjusting Brightness .........................................................36

4-3. Typical Gray Bar Pattern for Adjusting Contrast .......................................................... 37

4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................38

PRE

4-5. Typical Test Pattern for Adjusting Sharpness..............................................................39

4-6. Mirror Mode ...............................................................................................................44

IMINAR

7-1. PlasmaWall Model PL-43DHD Dimensions .................................................................57

7-2. PlasmaWall Model PL-50DHD Dimensions .................................................................58

A-1. PlasmaWall Service Remote Control ........................................................................ A-1

A-2. PlasmaWall Setup Menu .......................................................................................... A-3

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual ix

List of Figures

Notes:

IMINAR

PRE

x Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

1. Introduction

This Owner’s Manual describes how to install, set up and operate the Runco PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller (Models PL-43DHD and PL-50DHD). It describes the features and functions available with DHD Controller Software version 2.0 and later.

Throughout this manual, the Runco PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller are referred to collectively as the “PlasmaWall.” The information in this manual applies to both the PL-43DHD and PL-50DHD, except where otherwise indicated.

most out of the PlasmaWall.

Runco has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You can always find the latest version of this and other Runco product manuals on-line, at www.runco.com.

Runco welcomes your comments about this manual. Send them to techpub@runco.com.

Text Conventions: The following conventions are used in this manual, in order to clarify the information and instructions provided:

• Remote control button identifiers are set in upper-case bold type; for example, “Press EXIT to return to the previous menu.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc> and <Tab>.

• <Enter> indicates that you may press either the RETURN or ENTER key on your computer keyboard if it has both keys.

• Computer input (commands you type) and output (responses that appear on-screen) is shown in monospace (fixed-width) type; for example: “To change the aspect ratio to Anamorphic, type ANAMORPHIC <Enter>.”

PRE

IMINAR

1.1 About This Manual

Target AudienceRunco has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

In addition to these conventions, underlining, boldface and/or italics are occasionally used to highlight important information, as in this example:

Note

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 1

A carriage return must be used after each command or string.

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

1.2

Using This Manual

Tip

Note

Caution

TIPS highlight time-saving short cuts and helpful guidelines for using certain features.

NOTES emphasize text with unusual importance or special significance. They also provide supplemental information.

CAUTIONS alert users that a given action or omitted action can degrade performance or cause a malfunction.

WARNING

DANGER!

Use the following table to locate the specific information you need in this manual.

WARNINGS appear when a given action or omitted action can result in damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or death.

IMINAR

If you need... ... Turn to page:

Information about obtaining service iv

General information about the PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller

Installation instructions 15

PRE

First-time configuration instructions 29

Advanced configuration instructions 41

Troubleshooting tips 47

Specifications for the PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller

2 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Introduction

The PlasmaWall PL-43DHD and PL-50DHD flat-panel plasma monitors bring outstanding picture quality to their respective size categories with true, high-definition native resolution of 1024 x 768 (PL-43DHD) or 1280 x 768 (PL-50DHD) for no-compromise viewing of any video source.

The PlasmaWall is supplied with Runco’s next-generation, Digital High Definition (DHD) Controller, featuring advanced Vivix II™ processing. This controller produces stunning video imagery, elevating even standard NTSC material to near high-definition levels.

Multiple aspect ratio control includes Runco’s VirtualWide™ for viewing 4:3 material in widescreen with no loss of picture quality. The DHD provides for a pure digital signal path from input to output, making this system ready for Runco’s exclusive LiveLink™ DVI cable solution to preserve HD signal quality over long runs.

The PlasmaWall’s black level performance and shadow detail capability have been enhanced with Active Gray Scale Rendering to provide smoother transitions from dark to light, resulting in richly detailed textures even in shadowy scenes.

The PlasmaWall is easily integrated into custom installation systems. Both RS-232C and IR control interfaces are incorporated for simple automation. Its profile is less than 4-1/2 inches thin for wall-mounting simplicity.

• Native Resolution: 1280 x 768 (PL-50DHD) or 1024 x 768 (PL-43DHD)

• Multiple Aspect Ratios with VirtualWide™ Mode

• 160 degree horizontal/vertical viewing angle

• Accepts all DTV formats (via outboard decoder), including 1080i, 720p and 480p

• Less than five inches deep

• DVI Input with High-bandwidth Digital Content Protection (HDCP)

• Exceptional detail and artifact-free video enhancement

• Vivix™ video processing with 3:2 film detection circuitry

IMINAR

1.3 Description, Features and Benefits

Key Features and BenefitsThe PlasmaWall offers these key features and benefits:

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 3

Introduction

Parts List Your PlasmaWall is shipped with the following items. If any items are missing or damaged,

➤

please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.

• PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller

• AC Power Cords (2)

• Remote Control Unit and two (2), AAA-size batteries

• Service Remote Control Unit and two (2), AA-size batteries

• RJ-11 Telephone Cable, 50 feet (15.24 meters)

• Serial Port Adapter, RJ-11 Female to DB-9 Female

• Rack-mount hardware for the DHD Controller

• Cleaning Cloth

• Cable Ties (2)

• Warranty information and registration card

• Runco PL-43DHD and PL-50DHD Owner’s Operating Manual (this document)

Optional Accessories:

• Wall Mount Kit

• Table Stand

• LiveLink™ DVI Cabling System

IMINAR

PRE

4 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

2. Controls and Functions

Figure 2-1 shows the locations of the PlasmaWall front-panel controls and indicators.

IMINAR

2.1 PlasmaWall at a Glance

Controls and Indicators

PRE

1 23 4

Figure 2-1. PlasmaWall Front-Panel Controls and Indicators

1. POWER INDICATOR

- Lights green to indicate normal operation;

- Flashes green to indicate error conditions;

- Flashes green once per second when the power management feature is active.

2. STANDBY INDICATOR

- Lights red to indicate that the PlasmaWall is in standby mode;

- Flashes red to indicate error conditions.

3. DISPLAY STAND

Optional accessory for tabletop installations.

4. REMOTE CONTROL SENSOR

Receives the signals from the Setup remote control.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 5

Controls and Functions

Connectors Figure 2-2 shows the locations of the PlasmaWall connectors and main power switch.

➤

POWER

ONOFF

AC IN

SPEAKER

8Ω ~ 16Ω

10 11 12

SPEAKER

8Ω ~ 16Ω

Figure 2-2. PlasmaWall Connectors

PRE

IN OUT

COMBINATION

IMINAR

RS-232C

ANALOG RGB IN

D-Sub

ANALOG RGB OUT

D-Sub

3456789

INPUT1

AUDIO

DIGITAL RGB

DVI-D

INPUT 2

OUTPUT

AUDIOAUDIO

6 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

1. EXTERNAL SPEAKER OUTPUT (RIGHT)

Not used. Connect speakers to an external audio amplifier/receiver.

2. COMBINATION IN/OUT

Used to control multiple PlasmaWall monitors collectively. Use a 6-pin, mini-DIN cable (all pins wired straight-through).

3. RS-232C (9-pin, male D-Sub)

Connect the RS-232 OUT port on the DHD Controller to this input.

4. ANALOG RGB IN (INPUT 1) (15-pin D-Sub)

Connect the RGBHV (5xBNC) output from the DHD Controller here.

5. ANALOG RGB OUT (INPUT 1) (15-pin D-Sub)

If desired, connect this ouput to the RGB input of a second display device.

Controls and Functions

Note

6. AUDIO (INPUT 1) (3.5-mm stereo mini jack)

Not used with this model. Connect the audio outputs from your sources to an external audio receiver.

7. DIGITAL RGB (INPUT 2) (DVI-D)

HDCP-compliant digital video input. Connect the DVI output from the DHD

Controller to this input.

8. AUDIO (INPUT 2) (3.5-mm stereo mini jack)

Not used with this model. Connect the audio outputs from your sources to an external audio receiver.

9. AUDIO (OUTPUT) (3.5-mm stereo mini jack)

Not used with this model.

10. MAIN POWER SWITCH

Connects or disconnects the PlasmaWall from the AC power source.

11. POWER INPUT (100 to 240 VAC)

Connect the PlasmaWall to power here, using the included power cord.

12. EXTERNAL SPEAKER OUTPUT (LEFT)

Not used. Connect speakers to an external audio amplifier/receiver.

This output is not active when the PlasmaWall is off or in standby mode.

IMINAR

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 7

Controls and Functions

2.2

DHD Controller Front Panel

Figure 2-3. DHD Controller Front Panel

Figure 2-3 shows the controls and indicators on the DHD Controller front panel; the paragraphs that follow describe them.

1. RUNCO ICON

Lights red to indicate that the DHD Controller is in standby mode; lights blue to indicate that the unit is on.

2. POWER BUTTON

Press once to toggle from standby mode to on mode. Press it again to return to standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control.

IMINAR

3. IR SENSOR

Receives IR commands from the remote.

4. VACUUM FLUORESCENT DISPLAY

Can be used instead of the On-Screen Display (OSD). Displays currently-selected

PRE

menu or – if no menu is selected – the current source, signal format (NTSC or PAL), input resolution and aspect ratio.

8 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

5. UP BUTTON

Use to direct-select aspect ratios or move the menu cursor up in the On-Screen Display. When no menus are present on-screen, the UP button toggles you through aspect ratios in the following order: Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema

(For more information about aspect ratios, refer to Table 4-1.)

6. LEFT BUTTON

Used to direct select inputs or move the menu cursor left in the On Screen Display. When no menu is present on-screen, the LEFT button toggles you through the different sources, in this order: HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 Component SD - S-Video 2 - S-Video 1 - Composite

Controls and Functions

7. ENTER BUTTON

When an item is highlighted on the On-Screen Display, the ENTER button selects the item.

8. DOWN BUTTON

Use to direct select aspect ratios or move the menu cursor down in the On-Screen Display. When no menu is present on-screen, this button toggles you through the different aspect ratios, in this order: Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

9. RIGHT BUTTON

Used to direct select inputs or move the menu cursor right in the On Screen Display. When no menus are present on-screen, the RIGHT button toggles you through the different sources, in this order: Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1

- DVI

2 - HD Pass Thru 1 - HD Pass Thru 2

10. MENU BUTTON

Pressing the MENU button brings up the main menu. Also, if you are in an adjustment mode or function, pressing MENU brings the menu back one level.

IMINAR

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 9

Controls and Functions

2.3

Figure 2-4 shows the rear connector panel on the DHD Controller.

DHD Controller Rear Panel

Serial No

Runco International

Union City, CA

OUTPUTS

R/Pr G/Y B/Pb

Model

Video Processor / Controller

Figure 2-4. DHD Controller Rear Panel

Outputs 1. ANALOG OUTPUTS (RGBHV)

Inputs 3. DVI 1 / DVI 2 (Digital)

➤

R/Pr G/Y B/Pb

R/Pr G/Y B/Pb H V

2. DVI OUT

INPUTS

DVI 1 DVI 2DVI OutH/VVH

HD1

HD2

SDI

Pb Pr Y

Component Video

Option

SYSTEM CONTROL INTERFACE

TRIGGERS

S-Video 1

S-Video 2

RS-232 Out

Video

WARNING:

104

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING

TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

RS-232 Control

11 12 13 14

TO QUALIFIED SERVICE CENTER.

100-230VAC 50-60 Hz, 165 Watts Max

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Made In USA

Connect these to the ANALOG RGB IN input of the PlasmaWall, using a 5

x BNC-to-VGA breakout cable.

IMINAR

Connect this to the DIGITAL RGB (DVI-D) input on the PlasmaWall.

Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner with a DVI or HDMI output.

4. HD1 / HD2 (Analog BNC connectors)

Five, BNC connectors for connecting either RGB or component high-definition

PRE

television signals. The PlasmaWall automatically detects the signal format: RGB(HV) or YPrPb, 480p, 720p, 480i, 576i or 1080i.

5. COMPONENT VIDEO (RCA connectors)

Standard Definition (480i/576i) Component (YPrPb) input. This is the input for component video from sources such as DVD players.

Tip

For best results, do not run your DVD player in progressive mode.

10 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

6. COMPOSITE VIDEO INPUT

Standard composite video input for connecting a VCR, camcorder, laser disc player or other composite video source.

7. S-VIDEO 1 / S-VIDEO 2

Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.

8. 12-VOLT (750 mA) TRIGGER OUTPUTS

Connection for up to three (3), 12-volt trigger-controlled devices.

9. RS-232 OUTPUT (6-Wire, RJ-11 jack)

Connect this to the RS-232C input of the PlasmaWall, using the supplied serial port adapter and communication cable.

10. IR

Wired input from an external remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows: Ring = +5V Tip = IR Input Sleeve = Ground

Controls and Functions

Note

11. RS-232 CONTROL PORT

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

12. POWER INPUT (100 to 240 VAC)

Connect the DHD Controller to power here.

13. MAIN AC FUSE

This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow).

14. MAIN POWER SWITCH

Disconnects or applies power to the DHD Controller.

When an external remote control or infrared receiver is connected to the wired IR input, the IR sensor on the front of the DHD Controller is disabled.

IMINAR

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 11

Controls and Functions

2.4 DHD Controller Remote Control

Figure 2-5 shows the DHD Controller remote control, and the paragraphs that follow describe its functionality.

IMINAR

PRE

Figure 2-5. DHD Controller Remote Control

12 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

1. IR OUTPUT INDICATOR

Lights when a button is pressed to indicate that an IR signal is being transmitted.

2. ON / OFF

Press to turn the PlasmaWall on or off.

3. ENTER

Press to select a highlighted menu item or confirm a changed setting.

4. Cursor Keys ( , , , )

Use these buttons to select items or settings, adjust settings or switch display patterns.

When no menus are present on-screen, the UP and DOWN buttons toggle through the available aspect ratios, in this order:

UP Button = Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema DOWN Button = Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this order: LEFT Button = HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 HD/RGB 1 - Component SD - S-Video 2 - S-Video 1 - Composite RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 HD/RGB 2 - DVI 1 - DVI 2 - HD Pass Thru 1 - HD Pass Thru 2

5. LIGHT

Press to illuminate the buttons. (Not available on all models.)

Controls and Functions

6. MENU

Press this button to access the OSD controls, or to exit the current menu and return to the previous one.

7. VIDEO (1)

Press to select Composite video input as the source or to enter the numeric character

8. COMP (Component) (2)

Press to select Component SD (480i/576i) video input as the source or to enter the numeric character “2.”

“1.”

IMINAR

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 13

Controls and Functions

9. Aspect Ratio Selection Buttons

Use the red buttons to select an aspect ratio directly or to enter numeric characters, as follows:

ANA (Anamorphic) (3)

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4X3 (Standard 4:3) (6)

Scales the input signal to fit 4:3 display mode in the center of the screen.

LETBOX (Letterbox) (9)

For viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen.

V-WIDE (VirtualWide)

Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.

CINEMA For viewing 2.35:1 source material on a 1.78:1 (16:9) screen. The upper and lower portions are masked.

SVC

Not used.

10. S-VID 1 (4) / S-VID 2 (5) (S-Video)

Press to select an S-Video input or to enter the numeric character “4” or “5.”

11. HD 1 (7) / HD 2 (8)

Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “7” or “8.”

12. DVI 1 / DVI 2 (0)

Press to select a Digital Video input. Press DVI2 to enter the numeric character “0.”

13. Memory Preset Buttons:

ISF NT (Night)

Press to recall settings for the current input from the “ISF Night” memory preset.

PRE

ISF DAY

Press to recall settings for the current input from the “ISF Day” memory preset.

CUST 1

Press to recall settings for the current input from the “Custom 1” memory preset.

CUST 2

Press to recall settings for the current input from the “Custom 2” memory preset.

IMINAR

14 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

3. Installation

To install batteries in the remote control:

1. Press down the tab on the cover and pull the cover in the direction of the arrow.

2. Insert the included batteries. Ensure that the polarities correctly match the

compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place.

and markings inside the battery

IMINAR

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid

damage from battery leakage.

3.1 Remote Control

Notes on Batteries• When installing batteries, make sure that the battery polarities are correct.

The remote control can be used to control the PlasmaWall within the ranges shown in Figure 3-1.

PRE

Approx.

7m/ 23ft

Figure 3-1. Available Range of the Remote Control

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 15

Notes on Remote Control Operation

Installation

• Do not drop the remote control or expose it to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. If that occurs, move the plasma display away from the fluorescent lamp.

• Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the plasma display.

The signal from the remote control can be reflected by walls or

Note

• If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

• Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the plasma display and repeat the operation.

other surfaces.

IMINAR

PRE

16 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Installation

Table 3-1 gives a quick overview of the PlasmaWall installation process. The sections following this one provide detailed instructions.

Note

Table 3-1. Installation Overview

Step Procedure

1 Mount the PlasmaWall on a wall or table stand 18

2 Connect the DHD Controller to the PlasmaWall 21

3 Connect signal sources to the DHD Controller 23

4 Connect external controller to DHD Controller RS-232 port

(optional)

5 Apply power to the PlasmaWall 29

6 If using the PlasmaWall with a PC, adjust PC display prop-

erties

Installation should be performed by a qualified custom video installation specialist.

For Details, refer to

page...

IMINAR

3.2 Quick Setup

7 Display calibration: adjust the following for each input,

starting with Comonent SD; save settings when finished:

• Aspect ratio

• Brightness

• Contrast

• Color level

• Tint

• Sharpness

PRE

34 through 42

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 17

Installation

3.3 Installation Considerations

High-Altitude Operation Due to the design of all plasma glass panels made by every manufacturer, and the

Proper installation of your PlasmaWall will ensure the highest possible picture quality. Whether you are installing the PlasmaWall temporarily or permanently, you should take the following into account to ensure that it performs optimally.

➤

interaction between ambient air pressure and the plasma gases contained inside of the panel, reliable operation of your plasma display cannot be assured during operation at certain high-altitude locations.

Runco has found this plasma monitor to operate reliablly at altitudes of up to 5000 MSL (mean sea level). At elevations higher than this, each panel may react differently, depending upon the altitude, air pressure, humidity and other meteorological factors.

For this reason, Runco International makes no warranties or claims as to the reliable operation of the PL-43DHD or PL-50DHD at altitudes greater than 5000 feet above sea level. If you are planning to use this product at a location above 5000 feet, please contact Runco technical support for further information.

Mounting the PlasmaWall

on a Wall or

Table Stand

To install the PlasmaWall, you will need either an optional table stand or wall-mounting kit.

➤

The PlasmaWall cannot be installed on its own.

If you do decide to wall-mount the PlasmaWall, ensure that the wall-mount bracket is installed according to the instructions included with it. The wall must be capable of supporting a redundant weight factor three (3) times the weight of the display, or be reinforced.

IMINAR

Runco recommends that this be done by a custom installation specialist.

Note

Use only a Runco-approved wall-mount kit or table stand that is specifically designed for your display.

You can attach your optional mounts or stand to the PlasmaWall in either of two ways:

PRE

• While it is upright.

18 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

• As it lies flat with the screen face down. Place the protective sheet, which was wrapped around the plasma monitor when it was packaged, between the screen and your work surface to avoid scratching or otherwise damaging the screen surface.

images will be noticeably reduced if light directly strikes the display, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant.

space on all sides between it and surrounding objects, as shown in heat to disperse, maintaining the proper operating temperature.

Figure 3-2. This allows

Installation

Ambient LightIn general, minimize or eliminate light sources directed at the display. Contrast ratio in your

VentilationIf you are mounting the PlasmaWall in an enclosure, leave at least 2 inches (50 mm) of

Wall

50mm (2")

(2")

Wall

IMINAR

PRE

(2") 50

Figure 3-2. Ventilation Requirements for Enclosure Mounting

50mm (2")

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 19

Installation

Other Considerations Other considerations and tips that can help improve your installation, avoid damage and

➤

prolong operating life:

• Keep the ambient temperature constant and below 35°C (95°F). Keep the display away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the display circuitry, which may affect performance.

• Keep the PlasmaWall away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators.

• Handle the unit carefully when installing or carrying it. Use the built-in handles; DO NOT touch or hold the screen face.

• Set the unit away from heat, excessive dust, and direct sunlight.

• Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Service Center.

• Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

• For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

• To avoid sulfurization, it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath.

IMINAR

PRE

20 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Installation

Proceed as follows to connect the PlasmaWall to the DHD Controller, your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

• Turn off all equipment before making any connections.

• Use the correct signal cables for each source.

• Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

• Use the left audio input when connecting mono audio sources.

Connect the DHD Controller to the PlasmaWall as shown in Figure 3-3 and described in the sections that follow.

R/Pr G/Y B/Pb

RGB-HV

OUT

Runco International

Union City, CA

Serial No

Model

OUTPUTS

Video Processor / Controller

INPUTS

R/Pr G/Y B/Pb

R/Pr G/Y B/Pb H V

DVI 1 DVI 2DVI OutH/VVH

DVI OUT

SDI

Option

DHD Controller

HD1

HD2

Pb Pr Y

Component Video

Video

RS-232

OUT

SYSTEM CONTROL INTERFACE

TRIGGERS

WARNING:

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

S-Video 1

S-Video 2

RS-232 Out

TO REDUCE THE RISK OF FIRE

RS-232 Control

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.

100-230VAC 50-60 Hz, 165 Watts Max

Made In USA

IMINAR

3.4 Connections to the PlasmaWall and DHD Controller

Connecting the PlasmaWall to the DHD Controller

PRE

SPEAKER 8Ω ~ 16Ω

IN OUT

COMBINATION

RS-232C

ANALOG RGB IN

D-Sub

RS-232C

Figure 3-3. Connecting the PlasmaWall to the DHD Controller

ANALOG RGB OUT

D-Sub

ANALOG RGB IN (INPUT 1)

INPUT1

AUDIO

DIGITAL RGB

DVI-D

INPUT 2

OUTPUT

AUDIOAUDIO

DIGITAL RGB (INPUT 2)

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 21

Installation

Digital Video Connection: The PlasmaWall has a DVI input, labeled DIGITAL RGB. Connect the DVI output from the DHD Controller to this input, using a standard DVI cable.

RGBHV Connection: Connect the RGBHV output from the DHD Controller to the ANALOG RGB IN input on the PlasmaWall. Use a standard RGBHV breakout cable with

5 BNC connectors at each end.

RS-232 Connection: Connect the RS-232 output from the DHD Controller to the RS-232C input on the PlasmaWall. Use a standard, modular telephone cable with RJ11

plugs at both ends. On the PlasmaWall end, use the provided RJ11-to-DB9 adapter. This adapter is wired as shown in

Figure 3-4.

To/From

DHD

Controller

2, 5

1, 6

RJ-11 Male

IMINAR

Figure 3-4. RS-232 Connection from the DHD Controller to the PlasmaWall

PRE

XMT DATA

RCV DATA

SIG GND

REQUEST TO SEND

CLEAR TO SEND

NO CONNECTION

RCV DATA

XMT DATA

SIG GND

1, 9

DB-9 Female

PlasmaWall

1 5

6 9

RS-232C

22 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Installation

Connect your video sources to the DHD Controller as shown and described in the sections that follow.

DVI Connections: See Figure 3-5.

Tip

G/Y H VR/Pr B/Pb

G/Y

DVI 1

Use the DVI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the display.

INPUTS

DVI 2

HD1

HD2

HVR/Pr B/Pb

Pr Y

Component Video

Video

TRIGGERS

IR123

S-Video 1

S-Video 2

Connecting Source Components to the DHD Controller

PRE

Figure 3-5. DVI Source Connections

IMINAR

DVI Source

(DVD Player or HD Tuner with

HDMI or DVI out)

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 23

Installation

Digital (DTV) RGB Connections: See Figure 3-6.

G/Y H VR/Pr B/Pb

G/Y

DVI 1

Red/Pr Green/Y Blue/Pb Horiz Vert

INPUTS

DVI 2

HD1

HD2

HVR/Pr B/Pb

Component Video

IMINAR

Pr Y

TRIGGERS

12 3

S-Video 1

Video

S-Video 2

PRE

DTV or Progressive

Component (YPbPr)

Source

Figure 3-6. Digital (DTV) RGB Connections

24 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Analog (Computer) RGB Connections: See Figure 3-7.

Installation

Note

G/Y H VR/Pr B/Pb

G/Y

DVI 1

Red Green Blue Horiz Vert

1. Refer to Computer/Video Signal Compatibility on page 58 for a list of computer signals compatible with the PlasmaWall. Use with signals other than those listed may cause some functions not to work.

2. Some Macintosh computers may require a Macintosh video adapter. Contact your nearest authorized service center or dealer.

INPUTS

HVR/Pr B/Pb

DVI 2

HD1

HD2

Pb Pr

Component Video

TRIGGERS

123

S-Video 1

Y Video S-Video 2

IMINAR

PRE

Personal Computer

Figure 3-7. Analog RGB Connections

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 25

Installation

Composite/S-Video/Component Video Connections: See Figure 3-8.

INPUTS

G/Y H VR/Pr B/Pb

HD1

HD2

G/Y

HVR/Pr B/Pb

TRIGGERS

123

S-Video 1

DVI 1

IMINAR

DVD Player, VCR, Satellite Receiver, Laser Disc etc.

PRE

DVI 2

Pb Pr

Component Video

Pb Pr Y

Y Video S-Video 2

Figure 3-8. Composite, S-Video and Component Video Connections

26 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Installation

Use a standard, 9-pin RS-232 cable to connect a PC or home theater control/automation system (if present) to the RS-232 Control port on the DHD Controller; see

Figure 3-9.

For more information about using this connection, refer to Serial Communications on page 49.

345

2 Transmit Data 3 Receive Data 5 Ground

Pb Pr Y

Video

TRIGGERS

S-Video 1

RS-232 OutComponent Video

S-Video 2

RS-232 Control

(none of the other pins are used)

to Automation/

Control System

or PC

RS-232 Controller Connection

Figure 3-9. RS-232 Control System Connection

If your home theater contains equipment that responds to 12-volt triggers, connect them to the 12-volt trigger outputs as shown in

TRIGGERS

PRE

Video

S-Video 1

S-Video 2

RS-232 OutComponent Video

Pb Pr Y

to 12-Volt

trigger-activated

equipment

3.5-mm mini plug

Figure 3-10.

RS-232 Control

IMINAR

Figure 3-10. Connecting 12-Volt Trigger Outputs

Connecting 12-Volt Trigger Outputs to External Theater Components

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 27

Installation

Cable Management To minimize cable clutter, you can use the cable ties provided with the PlasmaWall to

➤

bundle the video, control and power cables at the back of the display. Install the cable ties as shown in

Figure 3-11. Cables can be routed to the right or left.

Do not allow excessive stress to be placed on the ends of cables.

Note

* As viewed from the rear of the display.

IMINAR

Figure 3-11. Installing the Cable Ties

PRE

28 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

4. Operation

1. Turn on your source components.

2. Plug the female end of the power cord into the AC receptacle on the rear of the PlasmaWall. Connect the other end to your AC power source.

WARNING

3. Similarly connect the DHD Controller to a nearby AC outlet.

4. Set the main power switch at the rear of the PlasmaWall (see Figure 2-2) to the “on” position. Its power indicator lights red.

5. Set the main power switch at the rear of the DHD Controller (see Figure 2-4) to the “on” position.

6. Press the ON button on the remote control to turn on the DHD Controller and PlasmaWall (or press the power button on the front of the DHD Controller). The power indicator on the DHD Controller lights solid blue.

7. After a brief warm-up period (approximately 10 seconds), the PlasmaWall will display an image.

The PlasmaWall input voltage is pre-set at the factory for either 100

– 120 VAC at 50/60 Hz or 200 – 240 VAC at 50 Hz.

Do not use a power supply voltage other than that for which the PlasmaWall is pre-set, as this may cause fire or electric shock.

IMINAR

PRE

4.1 Turning on the Power

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 29

Operation

4.2

Selecting the Input Source

4.3

Setting the PC Display Properties

By default, the PlasmaWall is configured to display the signal received on its RGBHV (ANALOG RGB IN) input. To use the DVI-D (DIGITAL RGB) input instead:

1. Press MENU and enter the Service Menu passcode.

Note

2. Select Service from the Main Menu.

3. Select Display Device from the Service Menu.

4. Press to select DVI/HDMI, then press ENTER.

You must enter a passcode to access the Service menu.

To maximize image quality when using the PlasmaWall with a personal computer, you may need to adjust the display properties of your PC video card. To do this:

1. Choose Settings from the Windows Start menu and click on “Control Panel.”

IMINAR

PRE

2. Double click on the Display icon.

3. Click the Settings tab on the display dialog box.

4. Adjust the resolution to 1024x768 or 1280x768 pixels.

30 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

5. Click the Advanced button and click the Monitor tab on the dialog box. Set the vertical frequency to 60Hz and click OK.

Operation

Note

WARNING

1. The native resolution of the PL-43DHD is 1024 x 768; the native resolution of the PL-50DHD is 1280 x 768. Other horizontal or vertical resolutions may be scaled upward or downward to fit the display.

2. With most computers, you can get the best picture at 1024

x 768 @ 60Hz or 1280 x 768 @ 60Hz.

3. For best results when using a computer, set the input on the DHD Controller to HD Pass Thru 1 or HD Pass Thru 2, depending on which RGB/HD input you are using.

To prevent image retention (burn) on your display, ALWAYS use a screen saver and set it to the shortest possible time.

IMINAR

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 31

Operation

4.4 Using the On-Screen Menus

Press the MENU button on either the remote control or the DHD Controller front panel to display the Main Menu. To select a menu item, use the UP ( on either the remote control or the DHD Controller front panel to highlight it. Press ENTER to confirm your selection.

The PlasmaWall OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source and signal characteristics, some menu options may not be available.

) and DOWN ( ) buttons

IMINAR

PRE

32 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Operation

Input Source

Aspect Ratio

Picture

Input Position

ISF Presets

Information

(read-only)

Service

Composite

S-Video 1

S-Video 2

Component SD

HD/RGB 1

HD/RGB 2

DVI 1

DVI 2 HD Pass Thru 1/

HD Pass Thru 2 (available only when Display Device Input Source = RGB)

Anamorphic

Standard 4:3

Letterbox

VirtualWide

Cinema

Brightness

Contrast

Color

Tint

Sharpness

Left/Right

Up/Down

Width

Height

Overscan

Recall ISF Night

Recall ISF Day

Recall/Save Custom 1

Recall/Save Custom 2

Reset Custom 1 & 2 to Factory Default

Serial Number

Hardware

Firmware

Date

Grey Bars 1

Test Video

Input Names Rename, Restore or Save

Remote Control

Analog Out Mode RGB--, RGB++ or RGBS

PRE

Display Device

HD Format

Triggers 1 / 2 / 3 / Save

Miscellaneous

Resolution

System Reset

Restore Saved Settings

Grey Bars 2

Color Bars 1

Color Bars 2

Primary

Secondary

Input Source RGB or DVI/HDMI

Configure

HD/RGB 1

HD/RGB 2

ADC Bandwidth Auto, 75 MHz, 150 MHz or 300 MHz

YPbPr Input Resolution Auto, 480i/p, 576i/p, 720p or 1080i

Language (currently, English only)

Menu Mode

Timeout

Side Bar Color

Film Mode (SD src. only) 800x600 ... 1400x1050

480p ... 720p ... 1080i

IMINAR

Calibration

Mirror Mode (flip horizontally, vertically or both)

Left/Right

Up/Down

Width

Height

Auto, RGB or YUV

Gain

Offset

ISF Night - Display Color

ISF Night - Input Image

ISF Night - Input Color

ISF Day - Display Color

ISF Day - Input Image

ISF Day - Input Color

Save ISF Settings Back / Confirm

Output Shift

Splash Configure

OSD Position

Color Temp. (available only when Display Device Input Source = RGB)

Brightness

Contrast

Color

Tint

Sharpness

Gain

Offset

Chroma Delay

Phase

Noise Filter

Gain

Offset Color Temp.

(available only when Display Device Input Source = RGB)

Brightness

Contrast

Color

Tint

Sharpness

Gain

Offset

Chroma Delay

Phase

Noise Filter

Left/Right

Up/Down

Width

Height

Save

Owner Name

ISF Calibrated

ISF Other

Splash Enable

Figure 4-1. DHD Controller OSD Menu Structure for PlasmaWall

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 33

Operation

Runco Video

Input Source

Aspect Ratio

Picture

Input Position

ISF Presets

Information

Calibration

Service

Input Source

> Composite

S-Video 1

S-Video 2

Component SD

HD/RGB 1

HD/RGB 2

DVI 1

DVI 2

HD Pass Thru 1

HD Pass Thru 2

Main Menu The Main Menu is the starting point for accessing all display functions.

Input Source From the Main Menu, select Input Source to choose a video signal source.

➤

(The Calibration and Service menus are hidden and not accessible until you enter a passcode.)

➤

The active source is indicated by an arrow (>) to its left; in the example at left, Composite is the active source.

Note

1. HD Pass Thru 1 and HD Pass Thru 2 are available only when the Display Device Input Source is set to RGB; refer to Device on page 44.

2. Selecting HD Pass Thru 1 or HD Pass Thru 2 loops the HD/RGB output. This prevents display of the on-screen menus. To switch

IMINAR

from HD Pass Thru 1 or 2 to another source, use the direct access buttons on the remote control, or the left- or right-arrow buttons on the DHD Controller.

1 or HD/RGB 2 input signal respectively to the RGB

Display

7    

Aspect Ratio To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio

Aspect Ratio

Anamorphic

Standard 4:3

Letterbox

VirtualWide

Cinema

PRE

➤

from the Main Menu and press ENTER. Select the appropriate aspect ratio for your screen size and the type of program material being viewed; refer to

The currently-selected aspect ratio is indicated by a “7” to its left; in the example at left, Anamorphic is selected.

Note

3. If the DVI 1 or DVI 2 input is active and the input signal is HDCP-encrypted, the RGBHV output of the DHD Controller is disabled.

Table 4-1.

The aspect ratio selection is automatically saved for each input and resolution.

34 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Table 4-1. Aspect Ratio Settings

Remote

Aspect Ratio

Anamorphic ANA Select Anamorphic to view 16:9

Control

Key

16:9 Image on

16:9 Screen

Description

DVDs and HDTV programs in their native aspect ratio. 4:3 images are stretched horizontally to fit a 16:9 screen.

Operation

4:3 Image on

16:9 Screen

Standard 4:3 4X3 Standard 4:3 scales the input

signal to fit in the center of the 16:9 screen. 4:3 is the aspect

Active Image

Area (4:3)

ratio used by computer monitors, standard television programming and most VHS video cassettes.

IMINAR

Letterbox LET

BOX

Letterbox Image on

16:9 Screen

In Letterbox mode, the image is stretched vertically; the top and bottom portions are “blanked off.” Letterbox is best suited for viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen.

PRE

VirtualWide V-WIDE A 4:3 image is scaled

NON-linearly (more on the sides than in the center) to fit a 16x9 screen.

Cinema CINEMA Select Cinema to view 2.35

source material on a 16:9

2.35:1 Image on 16:9 Screen

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 35

screen. The upper and lower portions of the screen are masked, but the geometry of the active image area is not changed.

Operation

Brightness

Contrast

Color

Tint

Sharpness

Picture

Picture Use the controls in the Picture Menu to calibrate your PlasmaWall for optimum picture

➤

quality.

The PlasmaWall has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup and calibration be performed by an ISF certified installation technician.

All signal types require separate processing. Therefore, you need to calibrate each DHD Controller input separately. Runco recommends calibrating the inputs in this order:

1. Component SD

2. S-Video 1 / S-Video 2

3. Composite

4. HD/RGB 1 / HD/RGB 2

5. DVI 1 / DVI 2

Note

Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Runco recommends using the following calibration tools for best results:

• External test pattern source – Ovation Multimedia, Video Essentials or AVIA test DVD (or equivalent).

• A blue filter (provided with many test DVDs), for color level and tint adjustments.

When you change a picture quality setting, save the change to a preset afterwards. Otherwise, the change will be lost when a different input is selected. (Picture quality settings are saved for each input separately.) For information about saving settings, refer to

ISF Presets on page 40.

IMINAR

Connect your test pattern source to the input that you are calibrating and proceed as

PRE

follows. Perform the adjustments in the order listed here.

Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an

acronym for “Picture Line-Up Generation Equipment.”) pattern.

Below Black

bove Black

Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness

Figure 4-2 shows a typical PLUGE

36 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

PLUGE patterns vary but generally consist of some combination of black, white and gray areas against a black background. The example above includes two vertical bars and four shaded boxes.

Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:

• The darkest black bars disappear into the background.

• The dark gray areas are barely visible.

• The lighter gray areas are clearly visible.

• The white areas are a comfortable level of true white.

• The image contains only black, gray and white (no color).

Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the one shown in

Figure 4-3.

Operation

IMINAR

Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast

Select Contrast and press ENTER. Adjust the contrast to a point just below which the white rectangle starts to increase in size.

Note

Brightness and contrast controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

PRE

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 37

Operation

Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in

Figure 4-4.

gray

yellow

cyan

green

red

magenta

blue

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Select Color and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

IMINAR

gray

yellow

cyan

green

red

magenta

blue

PRE

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Note

Like the brightness and contrast controls, the color and tint controls are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

38 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-5. Adjust as needed,

Operation

IMINAR

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

position for the current source.

Note

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Use the right or up cursor button to shift the image to the right; use the left or down button to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Use the right or up cursor button to shift the image upward; use the left or down button to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Use the right or up cursor button to increase the width; use the left or down button to decrease it.

Height: Select Height from the Input Position menu to change the projected image height. Use the right or up cursor button to increase the height; use the left or down button to decrease it.

The input position settings are automatically saved for each input

PRE

and resolution.

Input PositionUse the controls in the Input Position Menu to fine-tune the aspect ratio and image

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 39

Operation

Overscan: Image Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

Select from 1% to 10% of Overscan, as desired.

For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.

ISF Presets For each input, the PlasmaWall lets you save image quality settings as presets that you

ISF Presets

ISF Night

ISF Day



Custom 1 Save



Custom 2 Save



Factory Default

Information Select Information from the Main Menu to see information that uniquely identifies your

Information

Serial Number

Hardware 0

Firmware 0002.001B

Date Mar 24 2006

PRE

➤

can recall at a later time. You can create up to four presets per input and resolution. Use the ISF Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated by a “

7” to its left; in the example shown here, ISF Night is selected.

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

•Brightness

•Contrast

• Color saturation

•Tint

• Sharpness

To reset the Custom 1 and Custom 2 image presets to their factory defaults, select Factory Default and press ENTER.

➤

display: its serial number, the installed hardware and firmware versions and the firmware version build date. Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues.

IMINAR

40 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

should be used by ISF-certified technicians only.

Note

To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF Presets menu (see above). Or, use the corresponding buttons on the remote control.

ISF Night - Display Color: Use the Display Color settings to adjust the color balance at the display device (as opposed to the DHD Controller). These settings are saved independently for each input.

•Gain: Use the Gain controls to correct color imbalances in the bright areas of the

image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

•Offset: Use the Offset controls in the White Balance sub-menu to correct color

imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color.

• Color Temp (RGB Display Device only): Select Color Temp from the Display Color

menu to adjust the color temperature. The default setting is appropriate for most situations. Higher settings produce a “bluer” picture.

You must enter a passcode to access the Calibration menu.

Operation

CalibrationUse the Calibration menu to perform advanced picture quality adjustments. This menu

Calibration

ISF Night

Display Color

Input Image

Input Color

ISF Day

Display Color

Input Image

Input Color

Save ISF Settings

Output Shift

Splash Configure

OSD Position

ISF Night - Input Image: The Input Image controls are similar to those in the Picture

menu, but are accessible only by entering the Calibration menu passcode. This makes it possible to restore the picture quality settings to what they were when the display was installed, simply by recalling the “ISF Night” preset.

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance at the DHD Controller (as opposed to the display device). These settings are also saved independently for each input.

•Gain/Offset: Refer to ISF Night - Display Color, above.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a

Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

• Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or “noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

PRE

IMINAR

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 41

Operation

• Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Save ISF Settings: Whenever you make a change to the ISF settings, you should always

save it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever have to perform a Restore Saved Settings in the Service menu. (System Reset and Restore Saved Settings are described on page 46.)

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal. These settings are saved independently for each aspect ratio.

System Reset, you can restore the saved ISF settings by selecting

Service Use the Service menu to access advanced display configuration settings. This menu

Service

Test Video

Input Names

Remote Control

Analog Out Mode

Display Device

HD Format

Triggers

Miscellaneous

Resolution

System Reset

Restore Saved Settings

Splash Configure: Use the Splash Configure menu to customize the appearance of the

start-up message that appears on the vacuum fluorescent display upon power-up. You can have the PlasmaWall display the owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to 20 characters in length.

Use the up or down cursor button to select a character. Use the right and left cursor buttons to change the cursor position. Press MENU when you have finished entering text. Then, check the “Splash Enable” box to have the PlasmaWall display the information you enter here when it is turned on.

OSD Position: Select OSD Position, press ENTER and use the arrow buttons to change the size and position of the OSD controls.

➤

PRE

should be used by ISF-certified technicians only.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns on the PlasmaWall. Four patterns are available, consisting of white/gray or colored bars. These are useful for calibrating other theater source components (DVD player, HD tuner etc.) that have their own picture controls.

Press MENU to exit test pattern mode.

IMINAR

You must enter a passcode to access the Service menu.

42 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Input Names: You can give each DHD Controller input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component SD input names can be up to 12 characters long; the others can be up to eight characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press or

to select a character to change. When you have finished editing the input name, press

MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

To save input names so that they can be restored after a System Reset (described on page 46), press repeatedly to highlight “Save.” Then, press ENTER.

Operation

Input Names

Restore

Composite Composite

S-Video 1 S-Video 1

S-Video 2 S-Video 2

Component SD Component SD

HD/RGB 1 HD/RGB 1

HD/RGB 2 HD/RGB 2

DVI 1 DVI 1

DVI 2 DVI 2

Save

Note

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the DHD Controller will respond. By default, both are set to

17. You can change these codes if either:

• Another device in the theater (a DVD player, for example) is responding to commands from the DHD Controller remote control ( undesirable.

• You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific device.

Tip

Note

The button takes you from top to bottom in the left column, then from top to bottom in the right column. To highlight “Save,” scroll through both columns.

Figure 2-5) in ways that are unpredictable or

IMINAR

Use the DHD Controller front-panel keypad to change its IR code. Then, change the code sent by the remote to match as described

PRE

below.

Do not change the “Type” setting in this menu.

When you change a remote code on the DHD Controller, you must re-program your remote control to send that same code. To do this:

1. Using a straightened paper clip or similar object, press and hold the

CODE button on the remote control for approximately three seconds, or until the red LED on the remote lights solid red.

2. Enter a new two-digit code between 00 and 31 inclusive. Include a

leading zero for single-digit codes; for example, enter 9 as “09.”

3. The LED turns off to confirm the code change. If you enter an invalid code, the LED

flashes for three or four seconds. Try again, entering a valid code.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 43

Operation

Analog Out Mode: Select Analog Out Mode from the Service menu to change the characteristics of the analog output signal from the DHD Controller. The choices are RGB-- (separate sync with negative polarity), RGB++ (separate sync with positive polarity) or RGBS (composite sync).

Display Device: The options in the Display Device menu allow you to perform certain adjustments at the plasma display.

• Input Source: Select Input Source from the Display Device menu to switch from one

DHD Controller output/PlasmaWall input to the other. Use the RGB or DVI/HDMI, then press ENTER.

or button to select

Note

Tip

• Configure: Select Configure from the Display Device menu to perform the following

display device adjustments (these are global, independent of any input):

•Select Mirror Mode to change the displayed image orientation to suit the

installation method; see from a ceiling, you may want to mount it upside down and run the cables upward (toward the ceiling) to make them less visible. In this case, you would use the “XY” mirror mode.

IMINAR

PRE

Normal operating state Left-right reversal

If the DVI 1 or DVI 2 DHD Controller input is active and the input signal is HDCP-encrypted, the RGBHV output of the DHD Controller is disabled.

Use the serial command DISPLAY 1 or DISPLAY 2 to set the Input Source to RGB or DVI/HDMI respectively, so that the DHD Controller retains this setting after a change the Input Source in the Display Device menu.) For more information, refer to

Figure 4-6. For example, if the PlasmaWall is suspended

System Reset. (This is not the case when you

Miscellaneous Commands on page 53.

[MIRROR MODE: OFF]

Up-down, left-right reversal

[MIRROR MODE: XY]

Figure 4-6. Mirror Mode

•Select Left/Right, Up/Down, Width or Height to fine-tune the aspect ratio and

image position.

44 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

[MIRROR MODE: X]

Up-down reversal

[MIRROR MODE: Y]

HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the DHD Controller to switch from HD to 480i signals or vice versa.

This is generally not necessary unless the DHD Controller – for whatever reason – has difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming HD signal. In most situations, the Auto settings work well.

• HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.

• ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.

• YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i,

480p, 576i, 576p, 720p or 1080i.

Operation

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

To save the trigger settings so that they can be restored after a System Reset (described below), press

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

• Language: Select Language from the Miscellaneous menu and press the up- or

down-arrows to select the OSD language. (Currently, only English is supported.)

• Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear. 1 = Menus fade in and out. 2 = “Checkerboard” dissolve; menus appear and disappear in sections. 3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

• Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

• Side Bar Color: This controls the color of the inactive image area. The range is from

-100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the Standard 4:3 aspect ratio (or the entire screen when no incoming video signal is present).

• Film Mode: Enable Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the PlasmaWall detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode to ensure stable processing for that source.

repeatedly to highlight “Save.” Then, press ENTER.

IMINAR

PRE

Resolution: The DHD Controller defaults to an output resolution of 720p. When using the PlasmaWall with a computer or certain HD sources, you may want to force the DHD Controller to use a different output resolution. If so, select Resolution from the Service menu and choose one. Then, press ENTER to confirm.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 45

Operation

System Reset: To reset ALL DHD Controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel.

Caution

Restore Saved Settings: Following a System Reset, select Restore Saved Settings to apply all previously-saved settings to the PlasmaWall and DHD Controller.

This action is not undoable. Proceed with caution! Before you perform a System Reset, save ALL settings, including “Custom” ISF Presets ( settings (page 42), Input Names (page 43) and Trigger settings (page 45).

page 40), ISF Day/Night presets (page 40), Output Shift

IMINAR

PRE

46 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

5. Maintenance and Troubleshooting

Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the PlasmaWall. If you encounter an issue not described here, please contact your Runco dealer or Runco Technical Support.

Table 5-1. Troubleshooting Chart

Symptom Possible Cause(s) Solution

The display does not turn on after initial installation.

• The PlasmaWall is not plugged in or the AC outlet is not active.

• The DHD Controller is not plugged in or the AC outlet is not active.

•The remote control batteries have run out.

• The serial connection from the DHD Controller to the PlasmaWall is incorrect.

The PlasmaWall and DHD Controller are both on, but there is no picture and on-screen menus do not appear.

• Faulty or incorrect video connection between the DHD Controller and the PlasmaWall.

PRE

• Incorrect input source selection.

• Display Device input source is set to RGB, DHD Controller input is set to

1 or DVI 2 and DVI

DVI source is HDCP-encrypted.

• Ensure that the PlasmaWall is plugged in and that the AC outlet is active.

• Ensure that the DHD Controller is plugged in and that the AC outlet is active.

• Replace the batteries.

• Ensure that the RS-232 output from the DHD

IMINAR

Controller is properly connected to the RS-232C input on the PlasmaWall

Figure 3-3).

(see

• Ensure that the DVI and/or RGBHV outputs from the DHD Controller are properly connected to the video inputs on the PlasmaWall (see 3-3).

• Choose the correct input source on the display (refer

Selecting the Input

to Source on page 30).

• Set the Display Device input source to DVI/HDMI or use a different input on the DHD Controller for the encrypted source material.

Figure

5.1 Troubleshooting Tips

The display is on and menus appear, but there is no picture.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 47

• Incorrect source selection.

• Source component is not turned on.

• Source component is connected incorrectly or not at all.

• Select the correct source.

• Turn on the source

• Check connections from

component.

source component to DHD Controller.

Maintenance and Troubleshooting

Table 5-1. Troubleshooting Chart (continued)

Symptom Possible Cause(s) Solution

Image is too bright and/or lacks definition in the bright areas of the image.

Image appears “washed out” and/or dark areas appear too bright.

Colors in the image are swapped; for example, reds appear blue or vice versa.

RGB-HD images appear “noisy.”

“Out of range” appears on-screen.

IMINAR

• Contrast is set too high. • Lower the contrast setting.

• Brightness is set too high. • Lower the brightness setting.

• The Red/Pr, Green/Y or

Blue/Pb outputs from the source are connected to the wrong inputs on the DHD Controller.

• The Red, Green or Blue

(analog) outputs from the DHD Controller are connected to the wrong inputs on the PlasmaWall.

• Clock and Phase settings

need adjustment.

• The resolution and

frequency of the video card in the computer are not compatible with the PlasmaWall.

• Ensure that the source outputs are connected to the correct DHD Controller input.

• Ensure that the DHD Controller outputs are connected to the correct inputs on the PlasmaWall.

• Adjust Clock and Phase settings (refer to ISF Night

- Input Color on page 41).

• Select a compatible resolution and vertical frequency (refer to

Computer/Video Signal Compatibility on

page 59).

The image is too large or too small.

PRE

• Image size needs adjusting.

• Adjust the image size (refer to Input Position on page 39).

48 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

6. Serial Communications

To interface the PlasmaWall with a home theater automation/control system or a PC running terminal emulation software, connect it to the RS-232 output of the DHD Controller as shown in of the DHD Controller as shown in Figure 3-9.

Configure the RS-232 controller or PC serial port as follows: no parity, eight (8) data bits, one (1) stop bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller RS-232 port.

Serial commands to the DHD Controller take the following form:

• Commands are not case-sensitive.

• For a single command that takes no parameters, type the command followed by a carriage return; for example, to set the aspect ratio to Letterbox, type

LETTERBOX

• For a single command that takes a parameter, type the command, a space or a comma and the desired value followed by a carriage return; for example, to set the brightness to -10, type BRIGHTNESS

BRIGHTNESS,-10

• You can also send a string of multiple commands on a single line, separated by commas. For example, COMPOSITE,BRIGHTNESS switches to the Composite video input, sets the brightness to 100 and sets the aspect ratio to Anamorphic. Command strings can be up to 255 characters long.

<Enter>.

Figure 3-3. Connect your control system or PC to the RS-232 input

-10 <Enter> or

<Enter>.

100,ANAMORPHIC <Enter>

IMINAR

Note

Avoid combining the ON or POWER 1 commands with other commands on a single line. After sending ON or POWER 1, allow at least 15 seconds for the DHD and properly execute multiple serial commands.

Controller to power up. Once it does, it will accept

6.1 RS-232 Connection and Port Configuration

6.2 Serial Command Syntax

Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters.

When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >).

Table 6-1. Serial Commands

Command

OFF NA NA Turns system off

ON NA NA Turns system on

POWER 0/1 NA Turns system on or off (toggles on/off state)

POWER? NA NA Returns power status

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 49

PRE

Parameter

(min/max)

Value

Stored?

Power On/Off Commands

Description

Serial Communications

Table 6-1. Serial Commands (continued)

Command

COMPONENT NA YES Selects the Component input

COMPOSITE NA YES Selects the Composite video input

DVI1 NA YES Selects the DVI 1 input

DVI2 NA YES Selects the DVI 2 input

HD1 NA YES Selects the RGB HD 1 input

HD2 NA YES Selects the RGB HD 2 input

HD1PASS NA YES Loops HD1 input to RGBHV output

HD2PASS NA YES Loops HD2 input to RGBHV output

INPUT? NA NA Returns active input

SVIDEO1 NA YES Selects the S-Video 1 input

SVIDEO2 NA YES Selects the S-Video 2 input

ANAMORPHIC NA YES Selects the Anamorphic aspect ratio

Parameter

(min/max)

INARY

Value

Stored?

Input Selection Commands

Aspect Ratio Commands

Description

ASPECT? NA NA Returns current aspect ratio

ASPECTIN? NA NA Returns the input source aspect ratio

ASPECTOUT? NA NA Returns output screen size

CINEMA NA YES Selects the Cinema aspect ratio

LETTERBOX NA YES Selects the Letterbox aspect ratio

STANDARD NA YES Selects the Standard (4:3) aspect ratio

RELI

VIRTUALWIDE NA YES Selects the VirtualWide aspect ratio

50 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Table 6-1. Serial Commands (continued)

Serial Communications

Command

BRIGHTNESS -100/100 YES Sets a value for brightness

BRIGHTNESS? NA NA Returns brightness setting value

CHROMADELAY -12/12 YES Sets a value for input color chroma delay

CHROMADELAY? NA NA Returns input color chroma delay setting

COLOR -100/100 YES Sets a value for color

COLOR? NA NA Returns color setting value

CONTRAST -100/100 YES Sets a value for contrast

CONTRAST? NA NA Returns contrast setting value

FILMMODE 0/1 YES Sets Film Mode off (0) or on (1)

FILMMODE? NA NA Returns Film Mode setting (0 = off; 1 = on)

FILTER 0/15 YES Sets a value for input color noise filter

FILTER? NA NA Returns input color noise filter setting

PHASE 0/3 YES Adjusts phase

Parameter

(min/max)

Value

Stored?

Picture Adjust Commands

Description

IMINAR

PHASE? NA NA Returns phase setting value

SHARPNESS -6/6 YES Sets a value for sharpness

SHARPNESS? NA NA Returns sharpness setting value

TINT -100/100 YES Sets a value for tint

TINT? NA NA Returns tint setting value

Image Preset Commands

PRE

CUSTOM1 NA YES Loads “Custom 1” image preset

CUSTOM2 NA YES Loads “Custom 2” image preset

DAY NA YES Loads “ISF Day” image preset

NIGHT NA YES Loads “ISF Night” image preset

PRESET? NA NA Returns currently-selected preset

(ISF Day, ISF Night, Custom 1 or Custom 2)

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 51

Serial Communications

Table 6-1. Serial Commands (continued)

Command

IHEIGHT -100/100 YES Sets the value for input height

IHEIGHT? NA NA Returns input height value

IHPOS -100/100 YES Sets a value for horizontal input position

IHPOS? NA NA Returns input horizontal position value

IVPOS -100/100 YES Sets a value for vertical input position

IVPOS? NA NA Returns input vertical position value

IWIDTH -100/100 YES Sets the value for input width

IWIDTH? NA NA Returns input horizontal width value

OVERSCAN 0/10 YES Sets the overscan percentage

OVERSCAN? NA NA Returns overscan percentage

OHEIGHT -100/100 YES Sets the value for output height

OHEIGHT? NA NA Returns output height value

Parameter

(min/max)

INARY

Value

Stored?

Input Position Commands

Output Shift Commands

Description

OHPOS -100/100 YES Sets the value for output horizontal position

OHPOS? NA NA Returns output horizontal position value

OVPOS -100/100 YES Sets the value for output vertical position

OVPOS? NA NA Returns output vertical position value

OWIDTH -100/100 YES Sets the value for output width

OWIDTH? NA NA Returns output horizontal width value

RELI

52 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Table 6-1. Serial Commands (continued)

Serial Communications

Command

BKGND -100/100 YES Sets the background color for 4:3 aspect

BKGND? NA NA Returns background setting value

DATE? NA NA Returns product manufacture date

DISPLAY 1 or 2 YES Sets display device input source

DISPLAY? NA NA Returns display device input source value

HDINPUTRES NA YES Sets YPbPr input resolution and refresh

HWVER? NA NA Returns hardware version number

INRES? NA NA Returns input resolution

Parameter

(min/max)

Value

Stored?

Miscellaneous Commands

ratio (-100 = black; 100 = white)

(1 = RGB; 2 = DVI/HDMI)

rate for HD1/HD2, as follows: 0 = 480i 1 = 480p 2 = 576i 3 = 576p 4 = 720p / 60 Hz 5 = 1080i / 60 Hz 6 = 720p / 50 Hz 7 = 1080i / 25 Hz Any other value = Auto

IMINAR

Description

OUTRES 0/5 YES Sets output resolution, as follows:

0 = 480i 1 = 576i 2 = 480p 3 = 576p

PRE

OUTRES? NA NA Returns output resolution

RGBNN NA NA Sets output color space to RGB with

RGBPP NA NA Sets output color space to RGB with

RGBS NA NA Sets output color space to RGB with

SWVER? NA NA Returns software version number

TRIGGER 1/3 YES Assigns trigger to currently-selected aspect

4 = 720p 5 = 1080i

negative horizontal and vertical sync

positive horizontal and vertical sync

composite sync

ratio

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 53

Serial Communications

Notes:

RELI

INARY

54 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

7. Specifications

Table 7-1 lists the PlasmaWall specifications.

Table 7-1. PlasmaWall Specifications

Native Resolution: PL-43DHD: 1024 x 768

PL-50DHD: 1280 x 768

Screen Size (diagonal): PL-43DHD: 43 inches

PL-50DHD: 50 inches

Active Screen Area: PL-43DHD: 37.375 x 21.125 in. (949.3 x 536.6 mm)

PL-50DHD: 43.250 x 24.500 in. (1098.5 x 622.3 mm)

Screen Aspect Ratio: 16:9

Available Aspect Ratios: Refer to Table 7-2

DTV Compatibility: 480p, 720p, 1080i

Contrast Ratio: 1000:1

ISF Settings: Yes

Data/Graphics Compatibility: Up to 1600 x 1200

Inputs: (1) DVI 1.0 with HDCP

(1) RGB/Component (15-pin D-sub) (1) RS-232 (9-pin, D-sub male) (1) Combination in/out (6-pin mini-DIN jack)

IMINAR

7.1 PlasmaWall Specifications

Power Requirements: 100 to 120 VAC, 50/60Hz

220 VAC (pre-set at the factory only)

Power Consumption (typical): PL-43DHD: 380 W

PL-50DHD: 480 W

PRE

Operating Environment: 32ºF to 104ºF (0ºC to 40ºC);

20% to 80% humidity (non-condensing)

Dimensions: PL-43DHD: See Figure 7-1

PL-50DHD: See Figure 7-2

Weight: PL-43DHD: 80.0 lbs. (36.29 kg)

PL-50DHD: 96.0 lbs. (43.55 kg)

Regulatory Approvals: Complies with FCC

Limited Warranty: Three (3) years parts and labor from the date of delivery to

the end user (except for plasma glass panel). Plasma Glass Panel: One (1) year parts and labor from the date of delivery to the end user.

Specifications are subject to change without notice.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 55

Specifications

7.2

DHD Controller Specifications

Table 7-2 lists the DHD Controller specifications.

Table 7-2. DHD Controller Specifications

Aspect Ratios: 4:3, Letterbox, 16:9 Anamorphic, VirtualWide, Cinema

Video Standards: NTSC, PAL

Output Resolution: 480p, 576p, 720p, 840p, 960p, 1080i

Inputs: (1) Composite; (2) S-Video; (1) Component; (2) HD-R (Pr), G

(Y), B (Pb), H, V; (2) DVI with HDCP

Outputs: (1) HD-R (Pr), G (Y), B (Pb), H, V

(1) DVI-I with HDCP

Control Options: - Discrete infrared remote

- Serial commands via RS-232

- Front-panel controls

RS-232 Communication Parameters:

Trigger Outputs: (3) +12 VDC, each rated at 750 mA and thermal

Bandwidth: 150 Mega Samples per Second (MSPS)

Power Requirements: 100 to 240 VAC (auto-sensing), 50/60 Hz, 160 Watts

Operating Environment: 41°F to 95°F (5°C to 35°C), 0% to 90% humidity

IMINAR

19200 bps, no parity, 8 data bits, 1 stop bit, no flow control

fuse-protected

(non-condensing)

Dimensions: Width = 17.50 inches (444.5 mm)

Weight: 13.0 lbs. (5.90 kg)

PRE

Regulatory Approvals: Complies with FCC, CE C-Tick

Limited Warranty: Two (2) years parts and labor from the date of delivery to

Specifications are subject to change without notice.

Depth = 11.19 inches (284.1 mm) Height = 3.75 inches (95.3 mm)

the end user.

56 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Specifications

Figure 7-1 and Figure 7-2 show the PlasmaWall dimensions (all dimensions are in inches).

Front View Side View

21.491

43.306

43.657

26.738

38.001

2.100

Bottom View

42.246

39.063 0

1.103

3.963

IMINAR

Rear View

26.146

7.3 PlasmaWall Dimensions

19.217

13.311

7.405

4.675

0.593 0

Figure 7-1. PlasmaWall Model PL-43DHD Dimensions

PRE

0.530

11.825

31.325

42.776

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 57

Specifications

24.712

Front View Side View

49.133

50.229

43.729

30.045

2.080

29.515

20.968

15.062

9.156

PRE

IMINAR

.530

1.200

Bottom View

48.073

46.732

Rear View

14.801

34.293

1.253

4.093

48.603

Figure 7-2. PlasmaWall Model PL-50DHD Dimensions

58 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Specifications

The PlasmaWall can display video signals from a variety of computer sources via its RGB and DVI inputs.

Table 7-3 lists the signal types that are compatible with the PlasmaWall.

Table 7-3. Computer/Video Signal Compatibility Chart

Input

Resolution

(DotsxLines)

640x400 56.4 24.8 ** ** – NEC PC-9800

720x400

640x480

848x480 60.0 31.0 ** ** √

800x600

832x624 74.6 49.7 ** ** – Apple Macintosh 16”

1024x768

1280x720 60.0 44.7 *** ** –

1280x768

1152x864

Notes:

Refresh Rate

Vert.

(Hz)

70.1 31.5 ** ** – NEC PC-9800

85.1 37.9 ** ** –

60.0 31.5 ** ** √

66.7 35.0 ** ** – Apple Macintosh 13”

72.8 37.9 ** ** –

75.0 37.5 ** ** –

85.0 43.3 ** ** –

56.0 35.2 ** ** √

60.0 37.9 ** ** √ (1072x600)

72.0 48.1 ** ** –

75.0 46.9 ** ** –

85.0 53.7 ** ** –

60.0 48.4 * ** √ (1376x768)

70.0 56.5 * ** –

75.0

(74.9)

85.0 68.7 * ** –

56.0 45.1 *** * √

60.0 47.8 *** * √

70.0 56.1 *** * –

60.0 53.7 *** *** √

72.0 64.9 *** *** –

75.0 67.5 *** *** –

Horiz.

(kHz)

60.0

PRE

(60.2)

Display Quality

(refer to Notes)

PL-43DHD (1024x768)

PL-50DHD (1280x768)

* ** –

DVI

Support

Remarks

IMINAR

( ) = Apple

Macintosh 19”

7.4 Computer/Video Signal Compatibility

* = Optimal picture; may require changing the aspect ratio using the Service Remote Control

(refer to

** = Picture will be enlarged; some fine detail will be hard to see.

*** = Simple reproduction. Fine detail will not be reproduced.

– = Not supported.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual 59

Appendix A).

Specifications

Table 7-3. Computer/Video Signal Compatibility Chart (continued)

Input

Resolution

(DotsxLines)

1152x870 75.1 68.5 *** *** – Apple Macintosh 21”

1152x900

1280x960 60.0 60.0 *** *** √

1280x1024

1400x1050

1600x1200

Notes:

* = Optimal picture; may require changing the aspect ratio using the Service Remote Control

(refer to Appendix A).

** = Picture will be enlarged; some fine detail will be hard to see.

Refresh Rate

Vert.

(Hz)

66.0 61.8 *** *** – Sun Microsystems LO

76.0 71.7 *** *** – Sun Microsystems HI

60.0 64.0 *** *** √

75.0 80.0 *** *** – (1600x1024)

85.0 91.2 *** *** –

60.0 65.3 *** *** √

75.0 82.3 *** *** –

85.0 93.9 *** *** –

60.0 75.0 *** *** –

65.0 81.3 *** *** –

70.0 87.5 *** *** –

75.0 93.8 *** *** –

85.0 106.3 *** *** –

Horiz.

(kHz)

IMINAR

Display Quality

(refer to Notes)

PL-43DHD (1024x768)

PL-50DHD (1280x768)

DVI

Support

Remarks

*** = Simple reproduction. Fine detail will not be reproduced.

– = Not supported.

PRE

60 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

PlasmaWall Service Remote Control

Appendix A. PlasmaWall Service Remote

Control

The PlasmaWall system includes two remote control units: the standard DHD remote control (see

Figure 2-5) and the Service Remote Control, shown in Figure A-1 and

described in the paragraphs that follow.

ASPECT

RGB

RATIO

SETUP

PC/HDTV-1

SDTV-1

HDTV-2

SDTV-2

POWER

INFO

DIGITAL IN

MAGNIFY

SET

A.1 Overview

MUTE VOLUME

Figure A-1. PlasmaWall Service Remote Control

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual A-1

PlasmaWall Service Remote Control

Note

1. ASPECT RATIO

Press this button repeatedly to select a display aspect ratio (this may be necessary with certain computer resolutions).

2. POWER

Press to cycle the monitor between on and standby.

3. PC/HDTV-1

Selects INPUT 1 (ANALOG RGB IN) on the PlasmaWall.

4. HDTV-2

Selects INPUT 2 (DIGITAL RGB) on the PlasmaWall.

5. INFO

Displays timing information for the current input signal.

6. INSTALLER ADJUST (pin hole)

Used to access the INSTALLER ADJUST menu.

7. MENU

Pressing the MENU button brings up the main menu. Also, if you are in an adjustment mode or function, pressing MENU brings the menu back one level.

8. UP BUTTON

Use to move the menu cursor up in the On-Screen Display.

9. RIGHT BUTTON

Used to move the menu cursor right in the On Screen Display.

The PlasmaWall service remote control is intended for use only by authorized Runco dealers. Use it only as described here or as instructed to by Runco Technical Support.

A.2 Service/Setup Menu

10. LEFT BUTTON

Used to move the menu cursor left in the On Screen Display.

11. DOWN BUTTON

Use to move the menu cursor down in the On-Screen Display.

12. SET BUTTON

When an item is highlighted on the On-Screen Display, the SET button selects the item.

Note

For the vast majority of installations, the DHD Controller remote control gives you all the control you need over display quality settings. However, there are two settings internal to the PlasmaWall that can improve the displayed image quality on INPUT 1: VIDEO NR (noise reduction) and MPEG FILTER. These settings can be found in the Setup Menu, shown in

Figure A-2.

In order to use the PlasmaWall Service Remote Control, you must disconnect the PlasmaWall from the DHD Controller and connect a signal source to INPUT 1 on the PlasmaWall.

A-2 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

PLASMAWALL INPUT1

PICTURE SCREEN SETUP OPTION

AUTO POWER OFF

COLOR TEMP.

VIDEO NR

MPEG FILTER CHROMA EE CINEMA MODE COLOR SPACE CLAMP POSITION SIGNAL

DISABLE

MIDDLE

OFF

RGB

AUTO

750p

PlasmaWall Service Remote Control

SET

CHANGE EXIT

Figure A-2. PlasmaWall Setup Menu

To change the Noise Reduction setting on INPUT 1:

1. Press 1 to switch to PlasmaWall INPUT 1.

2. Press MENU on the PlasmaWall Service Remote Control.

3. Press or to select SETUP.

4. Press to select VIDEO NR, then press SET.

5. Press or to select the desired amount of noise reduction (OFF, LOW, MIDDLE or HIGH).

6. Press SET to confirm your selection.

1. Press 1 to switch to PlasmaWall INPUT 1.

2. Press MENU on the PlasmaWall Service Remote Control.

3. Press or to select SETUP.

4. Press to select MPEG FILTER, then press SET.

5. Press or to select the desired amount of filtering (OFF, LOW, MIDDLE or HIGH).

6. Press SET to confirm your selection.

Video NR (Noise Reduction)

MPEG FilterTo change the MPEG Filter setting on INPUT 1:

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual A-3

PlasmaWall Service Remote Control

Notes:

A-4 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

SERIAL NUMBER

RUMA-010900

rev 04-13-06 v3.0

Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300

www.runco.com

Runco CL-810 Owner’s Operating Manual

Runco PL-43DHD User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

THREE YEAR LIMITED WARRANTY

Safety Precautions

1. Introduction

1.1 About This Manual

Target AudienceRunco has prepared this manual to help home theater installers and end users get the

If You Have Comments About This Manual...

Textual and Graphic Conventions

Using This Manual

1.3 Description, Features and Benefits

Key Features and BenefitsThe PlasmaWall offers these key features and benefits:

Parts List Your PlasmaWall is shipped with the following items. If any items are missing or damaged,

2. Controls and Functions

2.1 PlasmaWall at a Glance

Controls and Indicators

Figure 2-1. PlasmaWall Front-Panel Controls and Indicators

Connectors Figure 2-2 shows the locations of the PlasmaWall connectors and main power switch.

Figure 2-2. PlasmaWall Connectors

DHD Controller Front Panel

Figure 2-3. DHD Controller Front Panel

DHD Controller Rear Panel

OUTPUTS

Figure 2-4. DHD Controller Rear Panel

INPUTS

2.4 DHD Controller Remote Control

Figure 2-5. DHD Controller Remote Control

3. Installation

3.1 Remote Control

Notes on Batteries• When installing batteries, make sure that the battery polarities are correct.

Figure 3-1. Available Range of the Remote Control

Notes on Remote Control Operation

Table 3-1. Installation Overview

3.2 Quick Setup

3.3 Installation Considerations

High-Altitude Operation Due to the design of all plasma glass panels made by every manufacturer, and the

Ambient LightIn general, minimize or eliminate light sources directed at the display. Contrast ratio in your

VentilationIf you are mounting the PlasmaWall in an enclosure, leave at least 2 inches (50 mm) of

Figure 3-2. Ventilation Requirements for Enclosure Mounting

Other Considerations Other considerations and tips that can help improve your installation, avoid damage and

3.4 Connections to the PlasmaWall and DHD Controller

Connecting the PlasmaWall to the DHD Controller

Figure 3-3. Connecting the PlasmaWall to the DHD Controller

Figure 3-4. RS-232 Connection from the DHD Controller to the PlasmaWall

Connecting Source Components to the DHD Controller

Figure 3-5. DVI Source Connections

Figure 3-6. Digital (DTV) RGB Connections

Figure 3-7. Analog RGB Connections

Figure 3-8. Composite, S-Video and Component Video Connections

RS-232 Controller Connection

Figure 3-9. RS-232 Control System Connection

Figure 3-10. Connecting 12-Volt Trigger Outputs

Connecting 12-Volt Trigger Outputs to External Theater Components

Cable Management To minimize cable clutter, you can use the cable ties provided with the PlasmaWall to

Figure 3-11. Installing the Cable Ties

4. Operation

4.1 Turning on the Power

Selecting the Input Source

Setting the PC Display Properties

4.4 Using the On-Screen Menus

Figure 4-1. DHD Controller OSD Menu Structure for PlasmaWall

Input Source

Aspect Ratio

Main Menu The Main Menu is the starting point for accessing all display functions.

Table 4-1. Aspect Ratio Settings

Brightness

Picture

Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness

Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

Input Position

Left/Right

Up/Down

Width

Height

ISF Presets

Information